2. Home
  3. Domestic appliances
  4. Climate control
  5. Fireplaces
  6. White Mountain Hearth
  7. Boulevard Direct-Vent Linear Contemporary Fireplace (DVLL60BP) Unpacking

White Mountain Hearth Boulevard Direct-Vent Linear Contemporary Fireplace (DVLL60BP) Unpacking, Boulevard Direct-Vent Linear Fireplace DVLL60 Unpacking, Boulevard Direct-Vent Linear Fireplace DVLL60 Unpacking Instruction Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the White Mountain Hearth Boulevard Direct-Vent Linear Contemporary Fireplace (DVLL60BP) Unpacking Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
36054-3-0618 Page 1
TOOLS REQUIRED:
• Metal Shear - To Cut Band Straps
• 5/16-inch Hex Drive With Extension
UNPACK THE FIREPLACE
1. Cut the binding straps and remove the shrink wrap.
2. Remove the top protective board and corner posts.
3. Inspectthereplaceforshippingdamage.
4. Liftthereplacefromthepallet.
CAUTION
This is an extremely heavy replace and requires two or more
people to move it. Use gloves when moving this replace.
5. Removethenon-combustibleboardsfromthepallet
andsetthemasideforuselater.
NOTICE:
Non-combustibleboardisrequiredfor
installationabovethereplaceasspeciedinthe
installation instructions.
6. Placethereplacenearitsnalinstallationlocation.
7. The Installation Instruction pack is located to one side
ofthereplace.
NOTICE: The burner or burner screen may have some
discolorationfromtestringatthefactory.Thisisnormal
and will not be visible once the burner screen is covered
with decorative crushed glass media.
REMOVE THE BARRIER SCREEN
1. Removethebarrierscreenassemblybygentlylifting
upwardtorelease,thenpullforward.
REMOVE DOOR LIMITER BRACKET
2. Onsomemodels,beforetheGlassDoorcanbe
removed, a Door Limiter Bracket must be removed.
Using a 5/16-inch hex driver with extension, remove (4
or 5) #10-24 x 3/8-inch screws that retain the Limiter
BrackettothebottomangeoftheGlassDoorframe,
and set the bracket aside. See Figure 1.
NOTICE: TheDoorLimiterBracket,ifincluded,
mustbere-installedtotheGlassDoorframepriorto
operationofthereplace.
DOOR LIMITER BRACKET
GLASS DOOR FRAME
Figure 1
REMOVE THE GLASS DOOR
3.
Remove the glass door using the glass door tool
securedtothetopofthereplace.Usingthetoolasa
lever,releasethebottomoftheglassdoorasshown
in Figure 2.
GLASS DOOR REMOV
AL TOOL
PLACE SMALL 90° END OF
THE
GLASS DOOR REMOVAL TOOL
BEHIND THE BOTTOM DOOR
FLANGE, THEN MOVE TOOL
SIDEWAYSTO DISENGAGE
THE RETAINER CLIPS
Figure 2
NOTICE: Tabs at the top allow the glass door to pivot
outwardatthebottom.Springclipsatthebottomofthe
doorframeengagefourbullettyperetainerstosecure.
4. Pivottheglassdooroutwarduntilthebottomofthe
dooropens6to8inches.Liftupwardonthedoorto
disengagethetopfromthetabretainersatthetop.
See Figure 3.
NOTICE: Because the door is extra long and heavy, it is
recommended that two people remove and install the
GlassDoortogether.
PIVOT
OUT
TABS
2
LIFT UP TO
RELEASE OFF
THE TABS
GLASS DOOR
ASSEMBLY
FIREPLACE
FACE
1
Figure 3
IMPORTANT! PLEASE READ!
36054-3-0618Page 2
MOVING FIREPLACE
Ifnecessary,thereplacecanbemovedwithahandtruck
as shown in Figure 4. The valve end must be up.
Beforemovingthereplacewithahandtruck,unpackthe
replace,removethebarrierscreen,glassdoor,inner
packaging materials, and the light cover. (If included)
TRUCK WITH
VALVE END UP
Figure 4
/