Fender Musical Instruments
7975 North Hayden Road, Scottsdale, Arizona 85258 U.S.A.
Since 1946, Fender realized the importance of your amplifier. You see, your amplifier
is more than just a combination of dials, wires and speakers. It is a finely tuned
musical instrument. And like any fine musical instrument, it should be treated with
special care and attention to detail.
At Fender, we know what building guitar amplifiers is all about. For over half a century,
we have been designing and producing some of the world's best amplifiers, helping
shape the face of music. In fact, many of the world's most classic and best sounding
amplifiers have proudly worn the Fender name.
Whether you're after that classic Fender tone, a clean crisp sound for your Bass or
Keyboard or the raw driving power of modern distortion, your decision to purchase a
Fender amplifier is one you will appreciate with each passing note for years to come.
Wishing you years of enjoyment and a heartfelt thank you,
Bill Schultz
Chairman
Fender Musical Instruments Corporation
Fender • Tone
Bill Schultz
Fender • Tradition
3
• ALL TUBE PREAMP AND POWERAMP GENERATE
THAT TONE AS ONLY TUBES CAN
• THREE DISTINCT CHANNELS: NORMAL, DRIVE AND
MORE DRIVE, FOR A BROAD PALETTE OF FENDER
TONES
• MAGNETIC INTERFERENCE REDUCING CHASSIS
ELIMINATES UNWANTED NOISE AND RADIO INTERFERENCE
• FENDER SPECIAL DESIGN
HIGH PERFORMANCE
SPEAKERS
• ROAD-WORTHY AND MUSICAL COMPONENTS, CAPABLE
OF HANDLING THE MOST DEMANDING PERFORMANCE
SITUATIONS
• CABINETRY CONSTRUCTED FROM HAND-SELECTED
WOODS, EMPLOYING RUGGED CORNER JOINERY FOR
ENDURING RELIABILITY
• COVERED IN GENUINE TOLEX FOR LONG LIFE AND
LASTING GOOD LOOKS
FENDER
®
AMERICAN TUBE AMPLIFIERS
HOT ROD DELUXE INTRODUCTION
Fender • Innovation
4
Road House Clean - Relic Strat '60's
Skank 'n' Crank - American Standard Strat (Guitar volume at 6 for skanking rhythm, open to 10 for cranking lead)
Aust-Tone - American Standard Strat
®
Neck Pickup
HOT ROD DELUXE SOUND SETTINGS
IN
IN
IN
Congratulations on your purchase of a Fender Hot
Rod Deluxe, the next step in the evolution of Fender
American Tube Amplifiers. The Hot Rod Deluxe is a
versatile musical instrument that features extensive
tone shaping abilities and virtually unlimited gain —
defining the next generation of FAT Fender Tone.
The Hot Rod Deluxe is rated at 40W R.M.S. and
includes among its many features a unique More
Drive function adding yet another sonic option to the
H.R’s potent arsenal of tones.
NOTE: If you’ve read this far… don’t stop now! Check
out the sound settings and experiment with them.
Spin the tone controls and see what happens…
Patch in the footswitch and give the Reverb a
twist… Roll back the drive, crank the master, make
those tubes dance …
So, take the time to get to know each other…
Tune-up, Plug-in and Play-on.
NOTES REGARDING BIAS:
Your new Fender amplifier has an internally mounted
variable bias control. The bias control is used to set the
idle current in your amplifier's output tubes, properly
matching the amp's performance characteristics to the
types of tubes you intend to use. Each different tube
brand and manufacturer may require a slightly different
bias setting. If you replace your tubes with the Fender
types your amp was originally outfitted with, no bias
adjustment is necessary. Having said that, an amp's
bias can drift over time in much the same way the
intonation settings on your guitar can. Both need to be
looked at periodically. The bias setting of a tube-type
amplifier is analogous to the idle setting on a car. If it is
not set properly, every other aspect of the system
suffers. A properly biased amp will sound great and
will run reliably and safely.
Also, beware! Internal voltages of tube-type amplifiers
are lethal and capacitors are capable of storing these
lethal charges. To ensure tone and safety, biasing
this amp (and all other amps) should be carried out by
qualified personnel only.
MORE... HOT ROD DELUXE SOUND SETTINGS
Live at Monterey - American Standard Strat Neck Pickup
Talkin' Trash - Tele
®
Jr.
Southern Snap - Tele Jr.
Funky Clean - Tele Jr.
Fat-A-Tude - Relic Strat
It Rocks - Guild S100
5
To Taste
IN
ININ
IN
IN
ININ
IN IN
Womanly - Guild
®
S100
IN
A. INPUT 1 - Plug your guitar in here.
B. INPUT 2 - A lower impedance and sensitivity
input than input 1, useful for guitars with active
pickups. When used with passive guitars, it pro-
vides a darker tone. Both inputs are identical if used
simultaneously.
C. BRIGHT/NORMAL - Adds top end brightness to
the NORMAL channel only.
D. VOLUME - Adjusts the overall loudness of the
NORMAL channel.
E. MORE DRIVE - When this button is pressed in,
DRIVE channel gain is increased providing more sustain.
F. DRIVE - Adjusts the amount of preamp gain in
the Drive channel. Turning this control up will
increase the amount of gain and overdrive. This
control works in conjunction with the MASTER
control to set the overall output loudness while the
drive channel is active.
G. TWO COLOR DRIVE CHANNEL INDICATOR -
When the DRIVE channel is in use, the LED is
illuminated. Yellow indicates "Drive", while red indi-
cates "More Drive".
H. TREBLE - Adjusts the amount of high frequency
boost or cut in both the NORMAL and DRIVE chan-
nels. NOTE: Like many vintage amplifiers, all tone
controls are pre-distortion and adjusting them
determines how the amplifier will distort.
I. BASS - Adjusts the amount of boost or cut in the
low frequency range in both the NORMAL and
DRIVE channels. Performance Tip: When playing at
higher volume levels, the tube power amp
enhances bass when it is overdriven. It may be
necessary to use lower bass settings when playing
at high volume settings.
J. MIDDLE - Adjusts the amount of boost or cut in
the middle frequency range in both the NORMAL
and DRIVE channels.
6
HOT ROD DELUXE TOP PANEL FUNCTIONS
MORE
DRIVE
NORMAL
BRIGHT
21
CHANNEL
SELECT
1
12
2
11
3
10
49
58
6
7
1
12
2
11
3
10
49
58
6
7
1
12
2
11
3
10
49
58
6
7
1
12
2
11
3
10
49
58
6
7
1
12
2
11
3
10
49
58
6
7
1
12
2
3
4
5
8
6
7
MASTER
MIDDLE
BASS
TREBLE
DRIVE
VOLUME
INPUTS
BB
A
CC
D
EF
GH
I
JK
L
K. CHANNEL SELECT - When this button is
pressed, the amp switches from the NORMAL
channel to the DRIVE channel.
L. MASTER - Adjusts the overall volume of the
DRIVE channel .
M. REVERB - Adjusts the amount of reverb present
in both the NORMAL and DRIVE Channels.
N. PRESENCE - Adjusts the amount of very high
frequencies present in both the NORMAL and
DRIVE Channels.
O. PREAMP OUT - This unbalanced jack provides
an output signal from the preamp and is pre-reverb.
It may be used to drive effects units in an effects
loop, to drive additional amplifiers in a multi-amp set
up, or as a preamp send to a mixing console.
P. POWER AMP IN - This unbalanced jack provides
a return from your effects units and is pre-reverb. This
jack can also be used as a power amp input.
Q. FOOTSWITCH (INCLUDED) - Plug-in connection
for the remote footswitch to select between the
NORMAL and DRIVE channels and to select "More
Drive". Using the footswitch overrides the front
panel select buttons. NOTE: Any good quality patch
cord will work with the remote footswitch, however, a
speaker grade cord is preferable to a coax guitar cord.
R. PILOT JEWEL - Illuminates if the Hot Rod
Deluxe is receiving power. Should this bulb burn
out, turn off and unplug the amplifier, unscrew the
red jewel and replace the lamp with a type T47 bulb.
S. STANDBY SWITCH - Turns the amplifier on and
off. In the STANDBY position, the amplifier is off.
When the "On/Off" switch (item T) is turned on,
power is supplied to the tube filaments eliminating
warm-up time. Using the STANDBY SWITCH during
short breaks versus using the on/off switch will
increase tube life.
T. POWER SWITCH - Turns the AC power ON
and OFF. When the amplifier is in the OFF position,
the amplifier is completely shut down.
7
ON
OFF
ON
STANDBY
CHANNEL
SELECT
12
11
10
9
8
7
1
12
2
11
3
10
49
58
6
7
1
12
2
11
3
10
49
58
6
7
1
12
2
11
3
10
49
58
6
7
PRESENCE
REVERB
MASTER
D
LE
POWER
AMP IN
PREAMP
OUT
FOOT
SWITCH
K
L
MN
O
P
Q
R
S
T
A. LINE CORD - the Hot Rod Deluxe is equipped
with a grounding type supply cord to reduce the
possibility of shock hazard. Be sure to connect it to
a grounded AC receptacle. DO NOT ALTER THE
AC PLUG.
B. FUSE - The fuse is in the AC supply of the ampli-
fier and will help to protect the amplifier in the event
of an electrical fault or tube failure. If a fuse blows,
replace it only with one of the same type and rating.
(Refer to the specification page to determine the
correct fuse type and rating for your amplifier).
NEVER use a fuse with a higher current rating as this
could damage the equipment and present a serious
safety hazard. If the amplifier repeatedly blows
fuses, it should be taken to an authorized Fender
service center.
C. MAIN SPEAKER - This is the main plug-in con-
nection to the speakers and must always be used as
their primary connection.
D. EXTERNAL SPEAKER - Plug-in connection for
an external speaker. This jack is wired in parallel
with the main speaker jack and must ONLY be used
in conjunction with the main speaker jack. If this
jack is used without the main speaker jack, there will
be no sound. The external speaker jack must be
used with an 8 ohm speaker enclosure.
E. CHANNEL SELECT - Allows the remote switching
from the NORMAL channel to the DRIVE channel.
F. DRIVE/MORE DRIVE - Allows the remote
switching of the Gain from Drive to More Drive.
NOTE: The tubes, external speaker jack, speaker
jack and fuse are not accessible by the user in
Scandinavian countries. Refer any servicing or
changes to a qualified technician.
8
DC
B
A
HOT ROD DELUXE BOTTOM PANEL FUNCTIONS
CHANNEL SELECT
DRIVE / MORE DRIVE
FENDER MUSICAL INTRUMENTS CORP.
MADE U.S.A.
E
F
If the amp is set up but does not function, check the following items:
• Is the power cord properly plugged into an electrical outlet?
• Is there power at the outlet?
• Is the fuse blown?
• Is the speaker properly connected to the amplifier?
• Are all the control knobs turned above two?
• Is the volume control on the instrument turned up?
• Is the instrument properly plugged into the amplifier?
(Eliminate any effects pedals and try using another cord.)
If after checking all of the above your amplifier is still not performing correctly,
consult your authorized Fender Service Center.
TROUBLESHOOTER'S CHECKLIST
The Hot Rod Deluxe tube compliment consists of
three Fender Special Design 12AX7A tubes (part
#099-5091) and two Fender Special Design
5881/6L6 WGC tubes (part #099-5090). For
continued optimum performance from your amplifier,
these tubes should only be replaced with tubes of
the same type and specification. Tube location is
printed on the tube label located inside the cabinet.
TUBE REPLACEMENT
TOLEX COVERING CARE
Your Hot Rod Deluxe is covered in genuine Tolex
for long life and lasting good looks. To clean the
Tolex covering, use a sponge and a light soapy
water solution. Avoid spilling liquids on the operating
surfaces, grill, volume and tone controls, switches
and speakers. ALWAYS unplug your amplifier
before cleaning or approaching it with fluids.
9
HOT ROD DELUXE SPECIFICATIONS
Hot Rod Deluxe
TYPE: PR 246
PART NUMBER: 21-3272 (100V)
21-3202 (120V)
21-3262 (230V)
21-3232 (240V)
POWER REQUIREMENTS: 100V AC, 50/60 Hz 180W
120V AC, 60 Hz, 180W
230V AC, 50 Hz, 180W
240V AC, 50 Hz, 180W
POWER OUTPUT: 40W into 8Ω or 4Ω at 5% THD
INPUT IMPEDANCE : INPUT 1: 1 MΩ
INPUT 2: 136 kΩ
PREAMP OUT 1.5 kΩ Max
OUTPUT IMPEDANCE:
POWER AMP IN 200 mV for clipping
SENSITIVITY:
POWER AMP IN 54 kΩ
INPUT IMPEDANCE:
TUBES: Three Fender Special Design 12AX7A tubes
Two Fender Special Design 5881/6L6 tubes
FUSE: 3A 250V fuse for 100V and 120V versions
1.6A 250V fuse for 230V and 240V versions
SPEAKER: One 8Ω Fender Re-issue "Gold
Special Label" 12" speakers
(P/N 037617)
FOOTSWITCH: 2 Button Footswitch, Controls
Gain and Channel Select
(P/N 050419)
DIMENSIONS: Height: 18.75 in 47.6 cm
Width: 23.5 in 59.7 cm
Depth: 10.5 in 26.7 cm
Weight 49.5 lbs 22.5 kg
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Service by persons other than Fender authorized service technicians
may void the warranty on this product.
THIS UNIT MUST BE EARTH GROUNDED.
THIS EQUIPMENT CONFORMS TO
THE FOLLOWING DIRECTIVES :
EMC 89/336/EEC AND LV 73/23/EEC
10
A Product of:
Fender
®
Musical Instruments Corporation
Corona, CA 91720 USA
TM
Our manuals are intended to be a reference source
throughout the lifetime of your product. We appreciate any
suggestions, and/or comments regarding this manual.
Please send your comments to:
Fender Musical Instruments Corp.
Research and Development
7975 North Hayden Road
Scottsdale, Arizona 85258, USA
Product specifications are subject to change without notice.
Fender
®
, Strat
®
, Tele
®
, and Guild
®
are Registered
Trademarks of the Fender Musical Instruments Corporation.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Century Next Step Deluxe Series Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
PylePro PEGKT15R Owner's manual
-
Fender Deluxe 85 Owner's manual
-
-
-
-
-
-
-
-