Terzismo PTL7145D User manual

Brand: Terzismo

Model: PTL7145D

Category: Washing machines

Type: User manual

ࠌشᎅࣔ஼

ীᇆ ˍ

Instruction and installation manual

Please read and save these instruction

P T L 7 1 4 5 D

Introduction

Read this manual carefully as it offers practical

advice to help you get the most from your washing

machine.

This «Instruction and Installation Manual» contains

everything you need to know about the everyday

running of your machine.

Please refer to this manual for installation and

maintenance instructions. The manual also contains

information about possible working problems,

advice about sorting clothes for washing, an

explanation of label symbols and hints about how to

remove stubborn stains.

1.- CONTROL PANEL 2.- LID 3.- DRUM

4.- DETERGENT DISPENSER 5.- PLINTH PANEL

6.- FILTER

Table of contents

page

Safety measures 3

Setting up - Installation 5

Preparing the wash. Opening/ closing the drum 7

Detergent load 8

Electronically-controlled variable load- Fuzzy Logic 8

Description of controls 9

Programmes selection 17

General recommendations 18

Troubleshooting 20

Washing hints 21

Safety measures

This appliance meets the European Directives

2004/108/EC, 2006/95/EC which have been substituted

respectively by 89/336/EEC, 73/23/EEC and subsequent

modifications thereof.

This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance

by a person responsible for their safety.

Children should be supervised to ensure that they do not play

with the appliance.

ATTENTION: FOR ALL CLEANING AND MAINTENANCE

WORK

• Remove the plug.

• Turn off the water inlet tap after each wash.

• The manufacturer fits all the machines with an earth

connection.

Ensure that the electrical installation has an earth connection

and that it is connected; if not, call a qualified Service Center.

The earth connection is essential for user safety as it elimi-

nates the risk of electrical discharge.

• Power sockets should be in easily accessible places so that

the washing machine can be unplugged in case of any

problems.

• If the electric cable is damaged replace with an original set

(cable and plug) supplied by the manufacturer or official after-

sales service.

note:

In the event that it is necessary to replace the power cable,

make sure that you comply with the following colour-code chart

during the wiring:

blue neutral

brown phase

Yellow-green earth

The manufacturer accepts no responsibility for any

damage to people or things resulting from the failure to

comply with the appliance’s installation and safety

regulations.

• Do not touch the appliance with wet hands or feet.

• Do not use the appliance when bare-footed.

• Use extension cords only with extreme care.

• Do not use adapters or multiple plugs.

• Do not allow the appliance to be used by children or the infirm

without due supervision.

• Do not pull on the power cord or the appliance itself to remove

the plug from the socket.

• Do not leave the appliance outdoors or exposed to the

atmospheric elements (rain, sun, etc.).

• Do not cover the appliance with cloth or plastic while it is

working.

• Do not install the appliance in damp places or anywhere

where it could be sprayed by the shower.

• Do not install the appliance on a surface which obstructs the

space between the floor and the base of the machine.

• Keep all packaging out of the reach of children as it could

constitute a health hazard.

ATTENTION:

DURING A WASH CYCLE THE WATER

CAN REACH TEMPERATURES OF 90ºC.

Setting up - Installation

• Unpack the appliance.

• Remove the 4 screws (A) from

both clamps and the 4

screws (B).

• Replace the 4 screws (A) and

fit the trims provided (D).

If your model offers this function:

Position the protection sheet as shown in the

diagram.

1.- Washing machine with wheel trolley.

2.- Washing machine without wheel trolley.

ATTENTION: DO NOT TURN THE TAP ON

• The washing machine should be connected to the

water mains via the new tube supplied with the

appliance (inside the drum). Do not use the old tube for

this purpose.

• Connect one end of the water inlet pipe with the elbow

bend to the electrovalve (top rear part of the machine)

and the other end to a tap or a plumbed-in 3/4" gas

threaded connection.

• Place the washing machine close to the wall, ensuring

that there are no bends or kinks anywhere in the tube.

Hook the outlet pipe to the edge of the sink or preferably

to a fixed drainage outlet of a diameter greater than that

of the outlet pipe and at a height of min. 50 cm. and a

maximum of 75 cm. from the floor.

If necessary, use the curved accessory to attach and

support the outlet pipe more securely.

If your model offers this function:

• To move the washing machine easily, turn the trolley

lever to the right. Once you have finished moving the

machine, return the lever to its original position.

• Level the machine by adjusting the front feet.

a) Turn the nut clockwise to release the screw on the

foot.

b) Raise or lower the foot by rotating it until it stands

firmly on the floor.

c) Lock the foot in position by turning the nut

anticlockwise until it comes up against the bottom of the

washing machine.

Check that the appliance is properly levelled.

Check that the washing machine does not rock by trying

to move two diagonally opposite top corners at the

same time.

• If you move the washing machine from one place to

another, you must level the feet again afterwards.

• Connect the machine.

Preparing the wash. Opening/ closing the drum

ATTENTION:

IT IS IMPORTANT TO MAKE SURE THAT THE

DRUM IS CAREFULLY OPENED AND CLOSED,

OTHERWISE THE MACHINE OR LAUNDRY

COULD GET DAMAGED.

ENSURE THAT THE DOORS FIT TOGETHER

PERFECTLY AND ARE PROPERLY CLOSED.

Open the washing machine lid.

Open the drum by pressing the (A) button with one

hand while pressing down on the opposite door

with the other.

Place clothes in the drum one item at a time, and

without squashing. Do not exceed the load limits

recommended in the “programme table”. An

overloaded washing machine will not wash

properly, and will leave clothing wrinkled.

To close the drum, place the doors so that the one

with the (A) button is below the other and they fit

together perfectly.

Detergent load

II I

Maximum Main wash

washing powder

Maximum Main wash

washing liquid

Maximum pre-wash

washing powder

recommended

Maximum scenting agent

The detergent dispenser is divided into 3 compartments:

.- Compartment I is for the pre-wash detergent.

.- Compartment II is for the main wash detergent.

.- The compartment

is for fabric conditioners, scenting agents and special additives such as starch,

blueing, etc.

The detergent dispenser has two reference marks:

.- Recommended (lower reference mark). This indicates the recommended level for the pre-wash and

main wash compartments.

.- Max. This indicates the maximum level, which should never be exceeded.

Important:

- Do not use liquid detergent for programs with a prewash cycle and/or timed start.

When the clothes present stains that need treatment with bleaches liquids products, you can proceed

to their preliminary cleaning in the washing machine. For that: Introduce the bleach product in the

"compartment II", and set the rinse program

. Once finished set the programmer to the OFF position,

add the rest of the laundry, and proceed with a normal was program.

Electronically- controlled Variable Load – Fuzzy Logic

This machine has electronics that automatically process all stages of the wash to ensure exceptional

results and at the same time save you time and money.

Once a programme has been selected, the machine optimises the following elements depending on

the wash load and type of fabric:

- quantity of water and power consumption

- wash time

- rinse efficiency

The washing machine also:

- detects suds and increases the amount of rinse water if necessary

- adjusts spin speed according to load distribution, thus forestalling any imbalance in the mechanism.

Description of controls

A Programme selector with OFF

position

B START/PAUSE button

C SPIN SPEED button

D TEMPERATURE SELECTION

button

E DELAY START button

F WASH TIME button

G EXTRA RINSE button

H OPTIONS button

I EASY IRON button

L Digital display

M DOOR LOCKED indicator light









Press the START/PAUSE button to start

the selected cycle.

 Once a programme is selected the

programme selector remains stationary on

the selected programme till cycle ends.

 Switch off the washing machine by

turning the selector to OFF.



Press to start the selected cycle.

ADD OR REMOVE ITEMS AFTER THE

PROGRAMMES HAS STARTED (PAUSE)



Press and hold the START/PAUSE

button for about 2 seconds (some

indicator light and the time remaining

indicator will flash, showing that the

machine has been paused).



Wait 2 minutes until the safety device

unlocks the door.



After you have added or removed items,

close the door and press the

START/PAUSE button (the programme

will start from where it left off).

CANCELLING THE PROGRAMME

 To cancel the programme, set the

selector to the OFF position.

WARNING:

Don’t touch the display while inserting

the plug because the machines

calibrates the systems during the first

seconds: touching the display, the

machine couldn’t work property. In

this case, remove the plug and repeat

the operation.

Opening the door

A special safety device prevents the

door from being opened immediately

after the end of the cycle.

Wait for 2 minutes after the wash

cycle has finished and the "Door

Security" light has gone out before

opening the door.

PROGRAMME selector with OFF

position

When the programme selector is turned

the display lights up to show the settings

for the programme selected.

For energy saving, at the end of the

cycle or with an inactivity period, the

display level contrast will decrease.

N.B.: To switch the machine off, turn the

programme selector to the OFF

position.

The programme selector must be

returned to the OFF position at the end

of each cycle or when starting a

subsequent wash cycle prior to the next

programme being selected and started.

START/PAUSE button

Close the door BEFORE selecting the

button START/PAUSE.

When the START/PAUSE button has

been pressed, the appliance can take

few seconds before it starts working.

 By pressing this button, it is possible to

reduce the maximum speed, and if you

wish, the spin cycle can be cancelled.

 To reactivate the spin cycle press the button

until you reach the spin speed you would

like to set.



It is possible to modify the spin speed

without pausing the machine.

 This button allows you to change the

temperature of the wash cycles.



It is not possible to raise the temperature

over the maximum allowed for every

programme, in order to save the fabrics.



This button allows you to pre-programme

the wash cycle to delay the start of the

cycle for up to 24 hours.



To delay the start use the following

procedure:

- Set the required programme.

- Press the button once to activate it (h00

appears on the display) and then press

it again to set a 1 hour delay (h01

appears on the display). The pre-set

delay increases by 1 hour each time the

button is pressed, until h24 appears on

the display, at which point pressing the

button again will reset the delay start to

zero.

- Confirm by pressing the START/PAUSE

button (the light on the display starts to

flash). The countdown will begin and

when it has finished the programme will

start automatically.



It is possible to cancel the delay start by

turning the programme selector to OFF.

If there is any break in the power supply

while the machine is operating, a special

memory stores the selected programme

and, when the power is restored, it

continues where it left OFF

The option buttons should be selected

before pressing the START/PAUSE

button.

If an option is selected that is

not compatible with the selected

programme then the option indicator

first flashes and then goes off.

SPIN SPEED button

To prevent damage to the fabrics, it is

not possible to increase the speed

over that which is automatically

suitable during the selection of the

program.

The machine is fitted with a special

electronic device, which prevents the

spin cycle should the load be

unbalanced.

This reduces the noise and vibration in

the machine and so prolongs the life of

our machine.

TEMPERATURE SELECTION button

DELAY START button



By selecting this button there is a choice

of 3 levels of wash intensity, depending

on how much the fabrics are soiled (can

be used only on some programmes as

shown in the table of programmes).

 Once the programme has been selected

the indicator light will automatically show

the wash time set for that programme.

 Selecting a different wash time the

relevant indicator will light up.

 This button allows you to add rinses at

the end of the washing cycle. The

maximum number of extra rinses is

related to the programme selected.



This function has been studied for the

people with delicate and sensitive skin,

for which also a least residue of detergent

can cause irritations or allergies.



It advises to also use this function for the

children items and in case of washings of

very dirty items, for which it is due to use

a lot of detergent, or in the washing of

toweling items whose fibres mostly have

the tendency to hold the detergent.

You can choose between three different

options:

- PREWASH

 This option allows you to make a prewash

and it is particularly useful for heavily

soiled loads (can be used only on some

programmes as shown in the table of

programmes).



We recommend you use only 20% of the

recommended quantities shown on the

detergent pack.

- HYGIENE PLUS



With this option it is possible to hygienize

the clothes, the washing programme

reach a temperature of 60°C.

- NIGHT & DAY



This option reduces the intermediate spin

speed to 400 rpm, where applicable,

increase the water level during rinsing and

keep the laundry immersed in water after the

final rinse, in order to spread the fibre

sevenly.



During the phase in which the water is

held in the tub, the relevant indicator light

blink to show that the machine is at a

standstill.

 Deselect the option to end the cycle with a

spin dry (which may be reduced or cancelled

using the appropriate button) and emptying

phase.



Thanks to electronic control, the water

in the intermediate phases is emptied

silently, making this option very useful for

washing at night.

This function allows you to minimizes

creases as much as possible, eliminating

the intermediate spins or reducing the

intensity of the last one.

WASH TIME button

EXTRA RINSE button

OPTIONS button

EASY IRON button

The display’s indicator system allows you to

be constantly informed about the status of

the machine.

1) DOOR LOCKED INDICATOR LIGHT



The indicator light is illuminated when the

door is fully closed.



When START/PAUSE is pressed on

the machine with the door closed, the

indicator will flash momentarily and then

illuminate.



A special safety device prevents the door

from being opened immediately after the

end of the cycle. Wait for 2 minutes after

the wash cycle has finished and the

DOOR LOCKED light has gone out before

opening the door. At the end of the cycle

turn the programme selector to OFF.

2) SPIN SPEED

This show the spin speed of the selected

programme that can be changed or omitted

by the relevant button.

3) WASH TEMPERATURE

This show the washing

selected programme that can be changed

(where allowed) by the relevant button.

4) CYCLE DURATION



When a programme is selected the

display automatically shows the cycle

duration, which can vary, depending on

the options selected.



Once the programme has started you will

be kept informed constantly of the time

remaining to the end of the wash.



The appliance calculates the time to the

end of the selected programme based

upon a standard loading, during the cycle,

the appliance corrects the time to that

applicable to the size and composition of

the load.

Digital Display

Close the door BEFORE selecting the

START/PAUSE button.

If the door is not properly closed,

the light will continue to flash for

about 7 seconds, after which the

start command will be automatically

delete. In this case, close the door

in the proper way and press the

START/PAUSE button.

8109

34 5 67

5) WASH TIME

{



Once the programme has been selected

the indicator light will automatically show

the wash time set for that programme.

 Selecting a different wash time the

relevant indicator will light up.

6) EXTRA RINSES

{

The indicator lights show the extra rinses

selected by the relevant button.

7) OPTIONS

}

The indicator lights show the option

that can be selected by the relevant

button (PREWASH, HYGIENE PLUS and

NIGHT & DAY).

8) WI-FI (some models only)



In the models with the Wi-Fi option, the

icon indicates that the Wi-Fi system is

working.

 For all other information in the Wi-Fi

system, there is a specific manual inside

the machine.

9) DELAY START

This flashes when delay start has been set.

10) Kg MODE (function active only on

Cotton and Synthetics programmes)



During the first minutes of the cycle, the

"Kg MODE" indicator remain on while the

intelligent sensor will weigh the laundry

and adjust the cycle time, water and

electricity consumption accordingly.

 Through every wash phase "Kg MODE"

allows to monitor information on the wash

load in the drum and in the first minutes

of the wash it:

- adjusts the amount of water required;

- determines the length of the wash cycle;

- controls rinsing according to the type of

fabric selected to be washed it;

- adjusts the rhythm of drum rotation for

the type of fabric being washed;

- recognizes the presence of lather,

increasing, if necessary, the amount of

water during rinsing;

- adjusts the spin speed according to the

load, thus avoiding any imbalance.

PROGRAM

kg*

(MAX.)

TEMP.°C DETERGENT

Recommended

Max.

Eco 20°C

20° 20°

Baby 60°C

4,5

60° 60°

Daily 59

2,5

40° 40°

Rapid 30

2,5

30° 30°

Rapid 14

30° 30°

Dark Colours

3,5

40° 40°

(

)

Auto Clean

Rinse

- -

Drain & Spin

- -

Shirts 1)

3,5

30° 30°

(

)

Lingerie

40° 60°

Wool & Silk

30° 30°

Delicates

2,5

40° 40°

Mixed 1)

3,5

40° 60°

(

)

40° 90°

(

)

Table of programmes

( ) Only with PREWASH option

selected (programmes with

PREWASH option available).

1) For the programmes shown you

can adjust the duration and

intensity of the wash using the

WASH TIME button.

IMPORTANT:

Do not use liquid detergent for programs with a prewash cycle and/or time delay.

PREPARING THE WASH CYCLE

1.- Once the washing is loaded, ensure that the drum doors are properly closed..

2.- Add detergent and additives, not exceeding the maximum level indicator.

.- detergent for pre-wash I

.- detergent for wash programme II

.- fabric conditioner

Technical data mod. PTL 7145D

Mains

voltage

Wash

power

rating

Spin

Power

rating

Pump

Motor

Power

rating

Heating

element

power

rating

Max.

Power

input

Mains

Fuse

Amp.

rating

Water

pressure

Water

consumption

*prog.

EN60456

Energy

consumption

*prog.

EN60456

220-230V.

50Hz.

175 W. 340 W. 30 W. 1300 W. 1500 W. 10 A.

0,05-0,8 Mpa

52 L.

0,75 Kw.

To clean different types of fabrics and

various levels of dirt, the washing machine

has specific programs to meet every need

of washing (see table of programmes).

Eco 20°C

This innovative programme, allows you to wash

different fabrics and colours together, such a

cottons, synthetics and mixed fabrics at only 20°

and provides an excellent cleaning performance.

Consumption on this program is about 40% of

conventional 40°C. cottons wash.

Baby 60°C

This program allows you to wash all baby

clothes getting a perfect clean and

sanitizing effect, setting the temperature a

60°C minimum. To optimize the result of the

sanitizing effect we recommend the use o

powder detergent.

Daily 59 Min.

This specially designed programme

maintains the high quality wash performance

whilst greatly reducing the wash time. The

programme is designed for a reduced load

(see table of programmes).

Rapid 30 Min.

complete washing cycle (wash, rinse and

spin). This programme is particularly suited

to slightly dirty cottons and mixed fabrics.

With this programme it is recommended to

use only 20% of the detergent normall

used to avoid waste.

Rapid 14 Min.

complete washing cycle (wash, rinse and

spin). This programme is suited to slightly dirt

cottons and mixed fabrics. With this programm

it is recommended to use only 20% of the

detergent normally used to avoid waste.

Dark Colours

Program designed to mix all dark garments and t

avoid the loss of colour and the formation of creases.

We recommend the use of liquid detergent.

Auto Clean

This program is suited to clean the drum of you

appliance. It is recommended to use thi

program every 50 washing cycles, to ensure a

long service life and avoid bad odors. Make sure

to start the program exclusively without laundry in

the machine, using only powder detergent fo

washing machine. When the washing cycle

finishes, open the door of the washing machine

to dry the drum.

Rinse

This program performs 3 rinses with an

intermediate spin (which can be reduced o

excluded by using the appropriate button) . I

is used for rinsing any type of fabric, fo

example after a wash carried out by hand.

Drain & Spin

The program completes the drain and a

maximum spin. It is possible to delete or reduce

the spin with the SPIN SPEED button.

Shirts

The washing cycle is optimized to reduce the

creation of creases, keeping an excellent washing

performance. It is also possible to further reduce

the spin speed, to ensure an easier ironing.

Lingerie

This program has been designed to

perfectly clean the everyday underwear: it is

particularly indicated for cottons and

resistant synthetics, with also the possibility

to mix colours (colourfast clothes only).

Wool & Silk

This programme allows a delicate washing

cycle, particularly suited to garments specified

as "Machine-Washable" Wool fabrics and

laundry items made from Silk or specified as

"Wash as Silk" on the fabric label.

Delicates

This program alternates among moments o

work during breaks and is particularly suitabl

for washing delicate fabrics. The wash cycle

and rinses are carried out with a high level o

water to ensure the best performance.

Mixed

The washing and rinsing are optimized in

the rhythms of rotation of the drum and to

the water levels. The gentle spin, ensures a

reduced formation of creases in the fabric.

This program is suitable to clean normall

soiled cotton laundry and it is the most efficien

program in terms of combined energy and

water consumptions for washing cotton laundry.

Programmes selection

General recommendations

CLEANING AND MAINTENANCE OF THE MACHINE

Do not use abrasives, spirits or solvents when cleaning the exterior of the washing machine. It is sufficient

to use a damp cloth.

The washing machine requires very little maintenance.

• Drying the rubber seal of the drum.

• Cleaning the dispenser and its compartments.

• Cleaning the filter.

• Cleaning prior to removals or when the machine is to stand idle for long periods.

To help conserve the washing machine, dry the rubber seal and leave the door open when the

cycle ends.

CLEANING THE FILTER

The washing machine comes with a special filter, located behind the machine’s front plinth panel, that

collects larger objects (coins, buttons, etc.) which could even block the pump.

It is advisable to clean the filter whenever the machine fails to rinse the clothes as well as it should

or when it fails to drain properly.

When it is necessary to clean the filter, proceed as follows:

• Use a basin to collect the water coming out.

• Remove the filter and clean it.

• Once the filter is clean, replace it by following the above-

mentioned pro in reverse.

CLEANING THE DETERGENT DISPENSER AND ITS COMPARTMENTS

.- It is advisable to clean the three compartments of the

detergent dispenser (pre-wash, wash, and fabric conditioner)

from time to time. To do this, remove the detergent dispenser

and after cleaning it, fit it back in place.

To remove and fit the detergent dispenser, follow the steps

indicated in the images.

removing

.- Press button A

.-Hold down the button and pull the detergent dispenser

outwards

.- Remove the dispenser and clean it

.- In the case of the pre-wash (I) and wash (II) compartments,

it is advisable to remove any dried-in remains of detergent

which obstruct the flow of the detergent to the drum.

.- In the fabric conditioner compartment, the trap (S) located at

the rear part of the dispenser should be removed by pulling

them out.

Remove any solid residue which could block the holes in the

compartments.

fitting

.- Fit in the tabs as shown

.- Push the detergent dispenser towards the housing (C) in the

door until the tab clicks into place.

Troubleshooting

FAULT CAUSE SOLUTION

1.- No programme works • The appliance is not plugged

in.

• The general switch is discon-

nected.

• There is no electricity.

• The fuses in the electric insta-

llation are damaged.

• The door is open.

• Plug it in.

• Activate the general switch.

• Check.

• Close the door.

2.- The appliance does not

load water

• See causes for 1.

• The tap is turned off.

• Check.

• Turn on the tap.

3.- The water does not drain • The filter is clogged.

• The outlet pipe is bent.

• Check the filter.

• Straighten the outlet pipe.

4.- The spin function does not

work

• The washing machine has not

yet drained the water.

• The “Spin Exclusion” option is

activated.

• Wait a few minutes for the was-

hing machine to drain.

• Enable the spin option.

5.- Strong vibrations during

spin cycle

• The washing machine is not

correctly levelled.

• The anchoring device for trans-

port has not been removed.

• The wash load is not evenly

distributed.

• Adjust the feet.

• Remove the transport support.

• Distribute it evenly.

6.- The high-speed spin does

not work

• The wash load is not evenly

distributed within the drum.

• Distribute the wash load evenly

in the drum.

7.- Display will show error nº

0,1,5,6,7,8,9,12,13,15,16

• Contact technical service.

8.- Display will show error nº 2

• Machine does not fill with water • Check that water inlet tap is open.

9.- Display will show error nº 3

• Water does not empty from

machine

• Check that outlet is not clogged

• Check for kinks in outlet tube.

10.-Display will show error nº 4

• Too much water in machine. • Shut off water tap.

• Contact technical service

If the problem or malfunctioning persists, disconnect the

machine, turn off the tap and do not try to repair.

For all repairs contact an Official Technical Assistance centre

and always insist on the

use of original parts. Failure to do so

of your machine.

When contacting a Technical Assistance Centre always refer to

the model (see also control panel) and the registration and serial

numbers indicated on the plate at the bottom front of the

machine behind the plinth panel or on the guarantee certificate.

That is to say, everything that appears in the box.

Providing this information will ensure a faster and more efficient

service.

may compromise the safety

Page is loading ...

Terzismo PTL7145D User manual

Brand: Terzismo

Model: PTL7145D

Category: Washing machines

Type: User manual

Download PDF

report

Terzismo PTL7145D User manual

Terzismo PTL7145D User manual

Related papers