Camerons Products MSC-2769-SLD User manual

Brand: Camerons Products

Model: MSC-2769-SLD

Type: User manual

This manual is also suitable for

Camerons MSC-2769-SLD

MSC-2769-SLD CAMERON

OWNER'S MANUAL

ASSEMBLY INSTRUCTION,CARE,

MAINTENANCE & USER'S GUIDE

",,,",,,

CAUTION

This unit is designed to be used safely by up 6 children between the age of 2

to 8, with a maximum weight of 100 pounds(45.4kgs) each, simultaneously,

not to exceed a combined weight of 600 pounds(272.72kgs).

WARNING

Please read this instruction manual before you start with the assembly or use this swing set.

You must follow all safety instructions while using this equipment; be absolutely sure that the surface, on which

this swing set is set up on, is properly surfaced with fine sand, wood chips or double shredded bark mulch. Do

not use this swing set on hard pack soil, concrete or any kind of hard surface. Read all cautionary statement on

page 1 - page 4, before using this equipment. Save this instruction manual for future reference.

CUSTOMER SERVICE:

DO NOT RETURN TO THE STORE,

PLEASE CALL

1-866-884-0535

Monday-Friday, 8:00AM-5:00PM Eastern Time

www.Sportspowercustomerservice.com

Sportspower Ltd

Flat M, 3/Floor, Kaiser Estate Phase 3, 11 Hok Yuen Street,

Hunghom, Kowloon, HongKong

USER'S GUIDE

1 [CAUTION!

]READ BEFORE USING THIS EQUIPMENT I

GENERAL INSTRUCTION

• Read this manual and follow all instructions before using and assembling this unit.

• Observing the following statements and warnings reduces the likelihood of serious fatal injury.

• Recommending on-site adult supervision for children of all ages at all times.

• This unit is designed to be used safely by up to 6 children between the age of 2 to 8, with a maximum

weight of 100 pounds (45.4 kgs) each, simultaneously, not to exceed a combined weight of 600 pounds

(272.72 kgs).

_WARNIN_Lawn swings is designed for use by children over two years of age. Use by children under the

age of two can result in entrapment between the seat and back areas. NEVER place children in rearward

facing position or with legs between the seat and backrest because the child's body may pass through the

opening causing entrapment of the child's head.

_WARNIN_ This unit must be assembled and disassembled by a capable adult person.

We suggest that you get someone to help.

Children must not use the equipment until properly assembled and anchored.

Always locate the swing set on level groundY

_WA_'_IN_ Do not allow swing set near any obstruction or sharp object ! Place gym set on level ground, not

less than 6ft (1.8m) from any structures or obstacles such as fence, garage, shed house, overhanging

branches, laundry line, electrical wires.

If the seats of swing, glide or slide are wet, do not use this equipment.

If any bolts & nuts are missing, do not use this equipment!

_WARNIN_ A capable adult should supervise the use of this equipment at all times. Do not allow reckless

playing, such as jumping off swing, slide, or Glide ride.

• Provide proper surface material cover for this equipment prior to using this equipment. See page 3 of this

manual for more information.

_WA_'_IN_ Do not allow more than one child to play on the swing, trapeze bar or slide at any one time.

Children shall take turns using the slide.

If the child has any physical condition that may affect his/her ability to use this equipment, one

shall consult a physician, before allowing the child to use this equipment.

,_WARNIN_ Do not allow child over the weight limit to use this equipment. Adults should never ride on any

of the rides, swing, trapeze or slide.

_WARNIN_ Do not allow child to stand on the swing seats or glide ride.

_WA_'_IN_ Instruct children not to walk too close in front of, behind, or between moving items. Instruct

children to keep a safe distance away to avoid being struck by items in play.

_WA_'_IN_ Instruct children not to twist swing chains or ropes or loop them over the top support bar since

this mac reduce the strength of the chain or rope.

_WARNIN_ Instruct children to avoid swinging empty play items.

_ Teach children to sit in the center of the swing play items, with their full weight in the seats.

_WARNINq Instruct children not to use the equipment in any manner other than intended.

_WARNIN_ Instruct children not to get off equipment while it is in motion. Do not allow children to jump

from moving play items.

_WA_IN_ Parent to dress children appropriately while on and around this equipment (Examples would

include the use of well fitting shoes and the avoidance of ponchos, scarves, jewelry and other loose fitting

clothing t]1at is potentially hazardous while using equipment).

_[_ WA_ING Do not allow children to climb or play on equipment when it is wet.

_WA_ING Do not stand on the lawn swing when using this ride. One child per seat only!

_WA_ING Check the openings between rollers and sliding surfaces of roller slides for foreign materials

that could be potentially hazardous to users.

• Please verify that suspended climbing ropes, chain, or cable are secured at both ends, and verify that

suspended climbing ropes, chain, or cable cannot be looped back on itself.

_WARNIN_ Instruct children not to attach items to the playground equipment that are not specifically

designed for use with the equipment such as but not limited to jump ropes, clothesline, pet leashes, cables

and chain as they may cause a strangulation hazard.

• It is recommended that the gym set be placed in concrete. Be certain that all anchoring devices ( including

concrete ) are placed below the level of the playing surface or below ground level to prevent tripping.

_WARNIN_ DO not allow children to lean to the side when riding on other rides, structural members on

collide with other playmates.

Do not install home playground equipment over concrete, asphalt, packed earth, grass, carpet, or

any other hard surface. A fall onto a hard surface can result in serious injury to the equipment user.

_WA_ING Do anchor all gyms.

_WA_ING If the swing set is set up on grounds with sandy soil condition, it must be anchored with

concrete footing (Concrete not included).

OPERATING INSTRUCTIONS

(WARNING THE BUYER)

Observing the following statements and warnings reduces the likelihood of serious or fatal injury.

This unit is designed to be used safely by up to 6 children between the age of 2 to 8, with a maximum

weight of 100 pounds (45.4 kgs) each, simultaneously, not to exceed a combined weight of 600 pounds

(272.7 kgs).

On-site adult supervision for children of all ages is recommended..

Instruct children not to walk close to, in front of, behind, or between moving items.

Instruct children not to twist swing chains or ropes or loop them over the top support bar since

this may reduce the strength of the chain or rope.

_ Instruct children to avoid swinging empty seats.

Teach children to sit in the center of the swings with their full weight on the seats,

WARNING]

Instruct children not to use the equipment in a manner other than intended,

Instruct children not to get off equipment while it is in motion.

_WA_IN_ Adult should dress children appropriately (examples would include the use of well-fitting shoes

and the avoidance of ponchos, scarfs, and other loose-fitting shoes and other loose-fitting clothing that is

potentially hazardous while using equipment).

_WA_IN_ Instruct children not to climb when the equipment is wet.

Please verify that suspended climbing ropes, chain, or cable are secured at both ends, and that

suspended climbing ropes, chain, or cable cannot be looped back on itself.

'_kWARNIN_ Instruct children not to attach items to the playground equipment that are not specifically

designed for use with the equipment, such as, but not limited to, jump ropes, clothesline, pet leashes,

cables and chain as they my cause a strangulation hazard.

Lawn swings, if applicable, are designed for use by children two years of age and older. The use by children

under the age of two can result in entrapment between the seat and back rest because the child's body may pass

through the opening, causing entrapment of the child's head. Such entrapment may result in strangulation.

NEVER place children in a rearward facing position or with legs between the seat and backrest.

_k WARNING Instruct children not to go down slide head first.

_WARNING Check slide bed for extreme heat before letting children use slide ( When exposed to direct

sunlight )

A /

AWARNIN_ Do not allow children to climb on swing from structural members (Legs, top bar and chin bar).

These are structural components only and NOT play features.

• If there is any cracked or damaged parts, do not use this equipment; call the 1-866-884-0535 number for

replacement part.

• Please save this instruction manual for future reference and review each season.

• Plastic components should be replaced every three years.

TIGHTENING NUTS & BOLTS

• At the start of assembling, do not tighten bolt/nut all the way, so to allow some possible adjustment, for

ease of installation.

• After all major components are assembled, go back over all bolts and nuts and properly tighten all of them

before using this product.

CARE & MAINTENACE INSTRUCTION

• Check all nuts and bolts twice monthly during the usage season for tightness and tighten as required. It

is particularly important that this procedure be followed at the beginning of each season.

• Oil all metallic moving parts monthly during the usage period.

• Sand rusted areas on metal tubing and repaint using a nonlead-based paint meeting the requirements of

Title 16 CFR Part 1303.

• Check swing seats, ropes, cables and chains monthly during usage season for evidence of deterioration.

Replacement should be made in accordance with manufacturer's instructions.

• Check all coverings for bolts and sharp edges twice monthly during usage season to be certain they are

in place. Replace when necessary. It is especially important to do this at the beginning of each new

season.

• Remove plastic swing seats slide and take indoors or do not use when temperature drops below 32

degrees F (0 degrees C).

Disposal Instructions

+ Please use with care to disassemble the unit, when it is no longer in operational condition. Wear

heavy duty working gloves!

+ Consumer may wish to recycle the steel tubing, please take the frame to your local recycling

center.

+ Be sure to completely disassemble the whole swing and slide sets, before disposal.

+ Do not leave partially disassembled equipment in area where accessible by children.

+ All plastic parts could be recycled, take it to your local recycling center.

+ All rusted parts, bolts shall be properly disposed of in trash bin. Do not reuse.

"_ Do not let children play with any disassembled parts destined for disposal, such as chain, slide,

tubings, bolts, nuts, screws!

IMPORTANT

CONSUMER INFORMATION SHEET

The Consumer Product Safety Commission estimates that about 100,000 playground equipment-

related iniuries resulting from falls to the ground equipment treated annually in U.S. hospital emergency rooms. Iniuries

involving this hazard pattern tend to be among the most serious of all playground iniuries, And have the potential to be fatal,

particularly when the iniury is to the head.

The surface under and around playground equipment can be a major factor in determining the iniury-causing potential of a fall.

It is self evident that a fall onto a shock absorbing surface is less likely to cause a serious iniury than a fall onto a hard surface.

Playground equipment should never be placed on hard surfaces such as concrete or asphalt and while grass may appear to be

acceptable it may quickly turn to hard packed earth in areas of high traffic. Shredded bark mulch, wood chips fine sand or fine

gravel are considered to be acceptable shock absorbing surface when installed and maintained at a sufficient depth under and

around playground equipment.

Table below lists the maximum height from which a child would not be expected to sustain a life-threatening head iniury in a

fall onto four different loose-fill surfacing materials if they are installed and maintained at depths of 6, 9, and 12 in.

FALL HEIGHT IN FEET FROM WHICH

A LIFE THREATENING HEAD INJURY WOULD NOT BE EXPECTED

TYPE OF MATERIAL 6INCH DEPTH 9INCH DEPTH 12INCH DEPTH

Double shredded bark mulch 6 10 11

Wood Chips 6 7 12

Fine Sand 5 5 9

Fine Gravel 6 7 10

However, it should be recognized that all iniuries due to falls can not be prevented no matter what surfacing material is used.

We recommend that a shock absorbing material should extend a minimum of 6ft in all directions from the perimeter of

stationary equipment such as climbers and slides. However, Because children may deliberately jump from a moving swing.

The shock absorbing material should extend in the front and rear of a swing a minimum distance of 2 times the height of the

pivot point measured from a point directly beneath the pivot on the supporting structure.

This information is intended to assist in comparing the relative shock-absorbing properties of various materials. No particular

material is recommended over another. However, Each material is only effective when properly maintained. Materials should

be checked periodically and replenished to maintain correct depth as determined necessary for your equipment. The choice of

a material depends on the type and height of the playground equipment. The availability of the material in your area and its

cost.

Note: The maximum fall height for this product is 6 feet. The minimum ground clearance between the bottom of the

suspended plays and the playing or ground service must be 8 inches.

YOU MUST MAINTAIN A MINIMUM OF 8 INCHES OF GROUND CLEARANCE

This information has been extracted from the CPSC publication on" Playground Safety". You can obtain more information by

sending a postcard to the: Office of public Affairs, U.S. Consumer Product Safety Commission, Washington, D.C. 20207.

HARDWARE (ACTUAL SIZE BUT FOR REFERENCE ONLY )

Hardware used for main frame assembly

,:LB1) BOLT 5/16"x63 4PCS _), BOLT 5/16"x63 12PCS

• :<........................i f

)

LBy NYLON NUT 5/16"

16PCS

_ ARC WASHER

28PCS

,_ LARGE WASHER

4PCS

Hardware used for swing seats assembly

'\ .........................../

'/J2"_' ARC WASHER

'\ //

4PCS

i 2_ LARGE WASHER

4PCS

/F-_\

J6 NYLONNUT 5/16"

k. /

8PCS

Hardware used for trapeze assembly

\ //

",2;; "- .........

i_S5) ARC WASHER

2PCS

NYLON NUT

2PCS

Bracket used for glide ride assembly

_N_ BOLT 5/16"x25 2PCS

@, NYLON NUT 5/16"

2PCS

Hardware used for glide ride assembly

_} BOLT 1/4"x34 4PCS

,<__ BOLT 1/4"x48 2PCS

/'i i\ Y,

'.\.._ ../ ,

_',_, BOLT 1/4"x34 4PCS

,@ SCREW O5.5x16 4PCS

_ NYLONNUT 1/4"

10PCS

_ CAP BOLT 1/4"x14 2PCS

f--\

(N10) SPRING WASHER

\\ /'

10PCS

_i_' ARC WASHER

4PCS

Hardware used for slide assembly

(Z_ BOLT 1/4"x34

14PC S

'\ j

_gl BOLT 1/4"x59 2PCS

_X BOLT 1/4"x96 2PCS

,_ SMALL WASHER

6PCS

/ \

_5_' NYLON NUT 1/4"

14PCS

\./

, __ SMALL ARC WASHER

4PCS

@ SPRING WASHER

12PCS

Tools needed for assembly

Special Socket Wrench

(included)

Tape Measure

Not included

wrench

(included)

Hammer

(If you intend to install

anchor, this is needed.)

Not included

j .........................................................................................................................................................J-' /

/J/' ,,//

_ "_/I j

Big Allen Wrench

(included)

Flat Head Philips

Head Screwdriver

Not included

Small Allen Wrench

(included)

Parts used for main frame assembly.

A1 _::::_:_:_:'_ LEFT TOP BAR 1 PC

A2 _ RIGHTTOP BAR 1 PC

A3 ....-s_::::_" MIDDLE TOP BAR 1 PC

A4 _ TOP SECTION LEG 4 PCS

A5 _ BOTTOMSECTION LEG 4 PCS

A6 %_ CROSS BAR 2 PCS

C2 5 _ END CAP (PREASSEMBLED) 2 PCS

Hardware used for main frame assembly

B1 BOLT 5/16".63 4 PCS

BOLT 5/16%63 12 PCS

B3 NYLONNUT 5/16 _ 16 PCS

B4 ARC WASHER 28 PCS

B5 WASHER 4 PCS

C1 PLASTIC CAP 20 PCS

Parts used for swing seats assembly

Jl ___ PVCCOVEREDCHAIN(PREASSEMBLED) 4 PCS

EYE BOLTWITH ATTACHMENT

J3 ,,9 BOLT (PREASSEMBLED) 4 PCS

J4 EYE BOLT (PREASSEMBLED) 4 PCS

K1 SWINGSEAT 2 PCS

K2 RUBBERCOVER (PREASSEMBLED) 4 PCS

Hardware used for swing seats assembly

J2 ARC WASHER 4 PCS

J5 LARGEWASHER 4 PCS

J6 NYLONNUT 5/16" 8 PCS

K3 PLASTIC CAP 8 PCS

Parts used for trapeze assembly

P1 TRAPEZE TUBE 1 PC

$1 EYE BOLT WITH ATTACHMENTBOLT 2 PCS

T3 RUBBER CAP (PREASSEMBLED) 2 PCS

Hardware used for trapeze assembly

$5 ARC WASHER5/16" 2 PCS

$6 NYLONNUT 5/16" 2 PCS

T4 PLASTIC CAP 2 PCS

1 0

Parts used for glide ride assembly

L1 TOP SECTION HANGER 2 PCS

L2 .....................................BOTTOMSECTION HANGER 2 PCS

L3 ......................................._ GLIDE SEAT SUPPORT 2 PCS

M1 TUBE CAP (PREASSEMBLED) 2 PCS

M2 SMALL NYLONBEARING (PREASSEMBLED) 4 PUS

M3 e_ LARGENYLONBEARING(PREASSEMBLED) 4 PCS

'°_ ' GLIDE SEAT 2 PCS

M4 _, y

M5 FOOTREST 2 PCS

Brackets used for glide ride assembly

L6 _

BRACKET CLAMP

REINFORCING STEEL SPACER

1 PC

2 PCS

N3 BOI,T 5/16".25 2 PCS

N7 NYLON NUT 5/16" 2 PCS

1 1

Hardware used for glide ride assembly

N1 _ BOLT1/4"'34 4 PCS

N2 _:_ BOLT1/4"'48 2 PCS

N4 i BOLT1/4_,34 4 PCS

N5 ii SCREWs5.5.16 4 PCS

N6 J-BOLT 2 PCS

N8 NYLONNUT1/4" 10 PCS

N9 CAPBOLT1/4".14 2 PCS

NIO SMALLWASHER 10 PCS

1 2

Parts used for slide assembly

SLIDE SUPPORT(W/ATTACH-MENTHOLE TO I,EG)

SLIDE SUPPORT

SLIDE LEG TUBE

SLIDE TOP SUPPORT BAR

SLIDE FRONT SUPPORT

SLIDE LADDER STEPS

SLIDE

CAP FOR X4(PREASSEMBLED)

1 PC

2 PCS

1 PC

3 PCS

1 PC

2 PCS

Hardware used for slide assembly

1 3

ASSEMBLY INSTRUCTION

Place the playground equipment on level ground, not less than 6 ft

(1.8 m) from any structure or obstruction such as a fence, garage,

house, overhanging branches, laundry lines, or electrical wires.

Do not install the playground equipment over concrete, asphalt,

packed earth, or any other hard surface. A fall onto a hard surface

can result in serious injury to the user.

TIGHTENING NUTS & BOLTS

Do not over-tighten the nuts and bolts when you are assembling

your playground equipment. This will allow for some possible

adjustments and ease of installation.

Once you have finsihed the assembly of the playground assembly,

go back over all of the nuts and bolts and properly tighten all of

them before using the playground equipment.

Main frame layout

// /

A5 J/

A1 ///

', \

\ ',,

A5 ',\,

' ',,

\ \,

\ ,,

1 4

Step 1

Insert A1 into A3, secure with B1, B3, B4 and C1.

Insert A3 into the other end of A2, secure with B1, B3, B4 and C1

Note: Please make sure that concave holes face down and round holes face up.

Round hole

faces up

Concave hole

faces down

Step 2

B2 B4

-L

/ /

J //

/ //

C1 2 B4 B2

Insert small end of A4 into the

socket at the end of A1.

Align the holes and secure

using B2, B4, B3 and C 1.

Insert small end of A4 into the

socket at the end of A2.

Align the holes and secure

using B2, B4, B3 and C1.

1 5

Step 3

Insert A5 into A4 and align the holes.

Attach A6 to the left outer side of A5.

Secure all three pieces using B2, B4, B5,B3 and C 1.

Repeat above the right side.

///

B4 A6

Cl B3

\, \\

Step 4

AS _\,, \\,

\\ \,

\ \,

',, \

Insert J3 which is pre-assembled with

J1, K2 and J4 into holes on A1.

Secure it with J2, J6 and K3.

Repeat for remaining two chains on A1.

1 6

Step 5

> AttachK1 to J4.

Secure with J5,J6 and K3.

Repeat for remaining One swing seat.

[ /

i /

Step 6

Attach P1 to S1.

;_ Attach S 1 to A3.

Secure using $5, $6 and T4.

1 7

Step 7

Attach L4, L5 and L6 to A2 as shown.

Secure using N3 and N7.

Use special socket wrench and screw

driver to tighten.

, //

USESPECIALSOCKET

WRENCHANDSCREW

DRIVERTOTIGHTENNT.

Step 8

Attach M5 to L2.

Secure using N5.

Attach L2 to L 1 and align holes.

Secure using N4, N10 and N8.

Insert M 1 into L 1if not pre-assembled.

Attach M 1 to the top of L 1 and insert

M2 into M1 and align if not pre-assembled.

N10

1 8

NIO

L1 _i

[ i

Step 9

Attach L1 to L5.

Secure using N2, N10 and N8.

L3 M3

Step 10

InsertM3intoL2 ifnot pre-assembled.

AttachL3to outersidesof L2.

SecureusingN6andN9. Seediagram

forsequence.

1 9

Page is loading ...

Camerons Products MSC-2769-SLD User manual

Brand: Camerons Products

Model: MSC-2769-SLD

Type: User manual

This manual is also suitable for

Camerons MSC-2769-SLD

Download PDF

report

Camerons Products MSC-2769-SLD User manual

This manual is also suitable for

Camerons Products MSC-2769-SLD User manual

Other documents