Short Form Specifications
Cabinet top surface shall be 16-gauge stainless steel with all cor-
ners welded and polished and reinforced with heavy-gauge channels.
Insulated folding lid shall be stainless steel with high impact plastic
liner and have chrome plated, die cast handles. Opening shall have a
throat liner constructed of high impact plastic.
The exterior sides and the watertight inner liner shall be 22-gauge
stainless steel. The unit shall be insulated with foamed-in-place high
density polyurethane. Unit to be equipped with 4.00" (10.2cm) diam-
eter, polylefin swivel casters and non-marking gray corner bumpers.
Refrigeration system controlled by an electronic control with built in
defrost timer. System will also include a blower coil and a condensate
evaporator. Unit designed to maintain a temperature setting from -5ºF
to 40ºF (-21ºC to 4ºC).
THE FOLLOWING APPLIES TO MODELS CP-2 AND CP-4 ONLY:
On CP-2 and CP-4, stainless steel perforated dispenser tubes (2 on
CP-2 and 4 on CP-4) for plates shall be furnished with properly cali-
brated, non-fatiguing stainless steel springs. Each dispenser tube
shall have a maximum capacity of approximately 50 plates.
NOTE: The maximum dish diameter that can be dispensed by these
models is 9.62" (24.4cm).
THE FOLLOWING APPLIES TO MODEL CM-2 ONLY:
On CM-2, self-leveling mechanism to be field adjustable by adding or
removing stainless steel extension springs on perimeter of vertical
side channels. A 20.00" x 20.00" (50.8cm x 50.8cm) carrier tray shall
be provided. The dispenser shall have a capacity of three to four 20"
x 20" racks (50.8cm x 50.8cm). Racks are not supplied by Delfield;
most hold 20-25 mugs.
Optional Accessories and Modifications
• Heavy duty casters (consult factory)
• Fiberglass panels
• Laminate panels
• Lid-locking device (specify model number)
Mobile chilled mug and plate dispensers
PROJECT
ITEM #
QUANTITY DATE
APPROVAL
CM/CP
MODEL CP-4
The Delfield Company, 980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2002 The Delfield Company. All rights reserved. Printed in U.S.A.
Techanical Data–Standard Unit
CM/CP
Mobile chilled mug and plate dispensers
MODEL APPROX. ELECTRICAL NEMA SHIP
NUMBER CAPACITY CONNECTION HP AMPS PLUG WEIGHT
CM-2 60 mugs 120V/60 Hz/ single phase 1/3 10.0 5-15P 485lbs - 200kg
CP-2 100 plates or bases 120V/60 Hz/ single phase 1/3 10.0 5-15P 410lbs - 186kg
CP-4 200 plates or bases 120V/60 Hz/ single phase 1/3 10.0 5-15P 485lbs - 220kg
NOTES:
• These models include a 9' (2.7cm) cord with NEMA 5-15 plug.
• The following information is required with an order to ensure proper operation of CP-2 and CP-4 models:
1) Height of one plate.
2) Overall diameter of the plate,
3) Height of a stack of eleven plates, and
4) Weight of a stack of 10 plates.
The Delfield Company, 980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2002 The Delfield Company. All rights reserved. Printed in U.S.A.
MSCM_CP 05/02
PLAN VIEW
CM-2 MODELS
ELEVATION VIEW
CM-2 MODELS
PLAN VIEW
CP-2 MODELS
PLAN VIEW
CP-4 MODELS
ELEVATION VIEW
CP-2 MODELS
ELEVATION VIEW
CP-4 MODELS
RIGHT END
CM-2 MODELS
RIGHT END VIEW
CP-2 MODELS
RIGHT END VIEW
CP-4 MODELS
48.00"
121.9cm
28.00"
71.1cm
20.37"
51.8cm
2.50"
6.4cm
32.50"
82.55cm
28.00"
71.12cm
20.37"
51.8cm
1.87"
4.8cm
13.12"
33.3cm
2.40"
6.1cm
MAX
9.62"
24.4cm
23.12"
58.7cm
48.00"
121.9cm
28.00"
71.12cm
20.37"
51.8cm
1.87"
4.8cm
13.12"
33.3cm
2.40"
6.1cm
MAX
9.62"
24.4cm
23.12"
58.7cm
36.00"
91.4cm
5.00"
12.7cm
5.00"
12.7cm
36.00"
91.4cm
5.00"
12.7cm
36.00"
91.4cm
/
