Jumpking ACC-UBSKU-BOLT Owner's manual

Please contact us at

[email protected]

- Please read all instructions prior to assembly.

- Adult supervision is required during assembly.

- Assembly requires 2 people.

- Use gloves during assembly to protect hands from pinch points and sharp edges.

- Check for any loose nuts and bolts, then tighten if necessary.

- Check all caps and coverings for defects or deterioration. Replace if necessary.

- Inspect the basketball hoop before each use and replace any worn, defective or missing parts.

- This basketball hoop is not suitable for assembly on an enclosure pole with a tunnel sleeve.

- For proper t and grip during assembly, the enclosure pole should be covered with a foam sleeve.

Model: ACC-UBSKU-BOLT

COMPATIBLE MODELS

Bent Pole

Outside Curved

Pole

Straight Pole

Curved Pole

Inside Straight

+ Curved Pole

Description:

Screw and nut set

for Basketball back

board (preassembled

to Part A)

Description:

Basketball Board

and Hoop

Inflatable ball

Quantity:

Part List

Part A Part B

Description:

Inflator and plastic

needle

Quantity:

Part C

Description:

7 Shape tube

Quantity:

Part D

Description:

Middle tube

Quantity:

Part E

Description:

Bottom tube

Quantity:

4 sets

Description:

Screw, nut and washer

set for Basketball back

board

Quantity:

1 set

Description:

Self Tapping Screw

Quantity:

2 pcs

Part F

Part G

Part H

Part I

Description:

Wedge

Quantity:

1 pcs

Description:

U-bolt

Quantity:

2 pcs

Description:

Lock Nut

Quantity:

4 pcs

Part J

Part K Part L

Description:

U-Bolt Bracket

Quantity:

2 pcs

Part M

Description:

Plastic Nut Cap

Quantity:

4 pcs

Part N

ACC-UBN/BBHN ACC-BSKB14

ACC-APN

ACC-UBU/CP

ACC-UBU/MP

HWSTS HWWEDGE HWUBOLT HWUBOLT

HWUBOLT HWUBOLT

ACC-UBU/BP ACC-UBU/SBBS4 ACC-UBU/SBP

How to assemble basketball hoop onto enclosure pole

Part D

Part H

Part E

Part F

Part I

Part J

Part K

Part L

Part M

Part N

Part H

You will need the following parts to complete this step:

1 x 7 Shape tube- Part D

1 x Middle tube - Part E

1 x Bottom tube - Part F

2 x Self Tapping Screw – Part I

Insert one end of the middle tube into the 7 shape tube

and the other end into the bottom tube.

Align the holes of all 3 tubes.

Screw one of the self-tapping screws through the hole

connecting the 7 shape tube to the middle tube and the

other screw through the hole connecting the middle tube

to the bottom tube using a Philips-head screwdriver (not

included).

You will need the following parts to

complete this step:

1 x Basketball Board and Hoop - Part

Parts D, E & F (assembled in previous

step)

4 x Screw and nut set for Basketball

back board - Part G (preassembled to

Part A)

1 x Screw, nut and washer set for

Basketball back board - Part H

Insert 7 Shape tube end into back of Basketball Board. Align

the holes and insert the screw, washer and nut and secure in

place with Philips-head screwdriver & socket wrench (not

included).

You will need the following parts to

complete this step:

1 x Wedge - Part J

2 x U-bolt - Part K

4 x Lock Nut - Part L

2 x U-Bolt Bracket – Part M

4 x Plastic Nut Cap – Part N

Align the basketball hoop onto one

of the trampoline enclosure poles.

Make sure the position of the

basketball hoop is facing inward.

Start attaching the U-bolts followed

by the wedges, U-bolt brackets and

lock nuts. Tighten with socket

wrench (not included). Then place

plastic nut caps over lock nuts.

Part A

Jumpking ACC-UBSKU-BOLT Owner's manual

Related papers

Other documents