Galley BarTap
®
Installation Guide
THEGALLEY
®
TA P
1
1
Before You Begin Installation
Package Contents
Tools
1. Observe all local plumbing codes.
2. Turn off water supply.
3. Inspect water supplies for signs of damage. Replace if necessary.
4. DO NOT use petroleum-based products on this faucet.
INSTALLATION WARNING: NEVER USE TEFLON TAPE FOR OUT-OF-THE-WALL THREADED CONNECTIONS. USE
PROVIDED RUBBER GASKETS ONLY. NOT COMPLYING WITH THIS INSTRUCTION COULD DAMAGE THE PRODUCT
AND GENERATE LEAKAGE.
#2 & #3 PHILLIPS SCREWDRIVERS ADJUSTABLE WRENCH ADJUSTABLE PLIERS
Remove all contents from the package and
identify before installation.
1 - Aerator Key
2 - Faucet
3 - Optional Base Ring
4 - Stainless Steel Mounting Washer
5- Stainless Steel Mounting Nut with Two
Crosshead Screws
6- Counterweight with two rubber strips
Note: All Hoses come pre-installed into Faucet and
are water tested at the factory.
Recommended Pressure Range: 20PSI -
75PSI
Maximum Flow Rate: l.8GPM / 6.8L /min
Maximum Temperature: 150° F
Product is Certified to NSF/ ANSI 372 and conforms with
the lead content requirements for “lead free” plumbing as
e defined by California, Vermont, Maryland, and Louisiana
state laws and the U.S. Safe Drinking Water Act. This
faucet complies with ASME 112.18.1-2018/CSA B125.1-2018
requirements.
2
1
3
5
6
4
TECHNICAL INFORMATION
2
Optional Base Ring
Stainless Steel Washer
Stainless Steel Mounting Nut
Stainless Steel Crosshead Screws
Ø 1- 1/2” fast water jet hole in
counter top
Ø 1-3/8” drill hole in counter top
Mounting Shank
Installation
Step 1
Step 2
Step 3
Hand Spray Supply Hose
Hand Spray Hose
Cold Supply
Hot Supply
Check Valve Housing
VERY IMPORTANT!
Step 5
Step 4
Step 6
Note: make sure the Hand Spray Hose and
Counterweight are free to extend or retract and
are not in conflict with any plumbing components
or items under the sink or Workstation.
H
C
1”
The Galley BarTap
®
comes with
an Optional Base Ring. It can be
installed with the Base Ring or
without it.
Insert all hoses and Mounting
Shank through the hole in counter
top.
On the underside of the counter
top, install the stainless steel
Washer and Mounting Nut by
slipping them over the hoses
and threading the nut onto the
Mounting Shank. Tighten the
Mounting Nut against the counter
top and tighten the two screws so
the faucet is secure.
Install the Counterweight onto the
Hand Spray Hose as shown.
Proper placement of the
Counterweights is critical for the
proper retraction of the spray hose.
Hand Spray Hose
Connect the Hand Spray Hose to the
Hand Spray Supply Hose on which
the Check Valve housing is fitted.
Before connecting the hot and cold
Supply Hoses, flush water supply
stops to clear any debris. Place
a bucket underneath the stops
and run water for 5 to 10 seconds.
Carefully turn on the water.
Carefully position hot and cold
supplies so they will not interfere
with other hoses.
Connect the 3/8” Compression
Connections (Hot and Cold Supply
Hoses) to your hot and cold inlets.
Hoses are marked hot and cold.
3
Usage
• Faucet turns on by tilting Handle out. Tilting angle is 24°. Handle rotates forward for temperature adjustment.
• When Handle is in upright position, water temperature is fully cold. When Handle is rotated 90° forward, water
temperature is fully hot.
• Adjust Slide Switch down for spray flow or up for laminar flow.
Laminar Flow
Spray Flow
Slide Switch
4
Maintenance:
Indoor Installation
Maintenance:
Outdoor Installation
1. CARTRIDGE REPLACEMENT:
• Using an Allen Key, unthread Set Screw from handle
• Unthread and remove Dome Cap and Cartridge Nut.
• Remove and replace Cartridge. Use the 2 pins on
the bottom of the Cartridge to seat the Cartridge
correctly.
2. CHECK VALVE REPLACEMENT:
• Unthread Hose and Check Valve Housing.
• Remove and replace Check Valves by inserting them
O-Ring side forward into Check Valve Housing.
• Re-assemble.
3. AERATOR REPLACEMENT:
• Use Aerator Key to remove and replace Aerator.
4. AERATOR CLEANING:
• Clean aerator periodically to eliminate any build-up.
Aerator
Aerator
Locking Ring
Aerator Key
Cartridge
Dome Cap
Handle
Allen
Key
Set
Screw
Cartridge
Nut
Check Valve Housing
Hand Spray Supply Hose
O-Ring
Check Valve
Hand Spray Hose
1. CARTRIDGE REPLACEMENT:
• Using an Allen Key, unthread Set Screw from handle
• Unthread and remove Dome Cap and Cartridge Nut.
• Remove and replace Cartridge. Use the 2 pins on
the bottom of the Cartridge to seat the Cartridge
correctly.
2. CHECK VALVE REPLACEMENT:
• Unthread Hose and Check Valve Housing.
• Remove and replace Check Valves by inserting them
O-Ring side forward into Check Valve Housing.
• Re-assemble.
3. AERATOR REPLACEMENT:
• Use Aerator Key to remove and replace Aerator.
4. AERATOR CLEANING:
• Clean aerator periodically to eliminate any build-up.
Important - Your outdoor Galley BarTap
®
must be winterized
if temperature falls below freezing in your area.
5. WINTERIZE YOUR GALLEY BARTAP:
• Turn off water supply under the counter and disconnect
Hot and Cold Supply Hoses.
• Disconnect Check Valve Housing and Hand Spray
Supply Hose (see picture below); remove both Check
Valves.
• Open handle and pull out Hand Spray from spout to
drain any water; drain completely.
5
1
1
Care and Cleaning the Galley BarTap
®
Finishes
Replacement Parts
The Galley BarTap is made of solid stainless steel. This finish has NO PROTECTIVE COATING on it. Stainless steel is by its material
nature very tarnish-resistant, but by no means tarnish or stain proof. This finish will react to it’s environment over time. Cleaners that
contain bleach may cause rust. Keep your Galley BarTap wiped clean and dry, and use only a cleaner specifically made for stainless
steel. Trapped moisture on the surface of your finish can lead to staining. Astringent cleaners, chlorine, bleach, and acidic-based
organic cleansers are potentially harmful to stainless steel finishes.
It is the responsibility of the customer to check for any material finish defects BEFORE installation.
1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use.
2. Periodic cleaning can be done by applying a stainless steel cleaner with a soft, clean cloth to gently remove surface spots and
brighten the finish. For PVD finishes, clean with a soft, warm, damp cloth.
3. Never use cleaners with bleach, abrasives or vinegar. Never use any type of abrasive cleaning pad.
ABOUT OUR FINISHES:
IMPORTANT NOTICE:
SUGGESTED FINISH MAINTENANCE PROCEDURE:
1. Hand Spray
2. Aerator & Ring
3. Aerator Key
4. O-Ring Gasket
5. Acetal Ring
6. Acetal Ring
7. Set screw
8. Cartridge
9. Cartridge Nut
10. Dome Cap
11. Handle
12. Set screw
13. O-Ring Gasket
14. Base Ring
15. O-Ring Gasket
16. Mounting Washer
17. Mounting Nut
18. Mounting Nut Screws
19. Gasket
20. Counterweight
21. Adhesive Strips
22. Check Valve
23. Hand Spray Hose
* XXX Represents Finish
X.1062-XXX
A.362
S.203
O.021
S.
S.241
A.128
S.232
B.709
B.710-XXX
F.019-XXX
A.356
O.066
B.711-XXX
O.022
A.358
F.016
A.357
A.064
S.252
S.273
A.290
A.344
13
19
11
6
4
14
15
16
17
18
12
10
3
2
1
9
8
20
21
23
22
5
7
6
Replacement Parts
The Galley Tap - Limited Lifetime Warranty
11.
Seller provides a Limited Lifetime Mechanical Warranty. Seller warrants its products, installed in a residential application, to be
free from manufacturing defects in materials and workmanship under normal usage for the useful life of the product. This Limited
Lifetime Mechanical Warranty is subject to the warranty conditions and limitations as set forth below.
Seller provides a Limited Lifetime Finish Warranty. For the following Finishes: Polished Stainless Steel, Matte Stainless Steel, PVD
Satin Black Stainless Steel, PVD Gun Metal Gray™ Stainless Steel, PVD Polished Rose Gold Stainless Steel and PVD Brushed Gold
Stainless Steel, seller warrants its finishes, installed in a residential application, to be free from manufacturing defects in materials or
workmanship for the useful life of the product. Please refer to the Seller’s Care Instructions for the proper maintenance of Seller’s
finishes. This Limited Lifetime Finish Warranty is subject to the warranty conditions and limitations as set forth below.
Seller’s Mechanical and Finish warranties are non-transferable and are strictly limited to products correctly installed using our
installation instructions and used in a residential environment. Mechanical or finish problems which result from abuse, misuse,
improper installation, improper maintenance, (including not properly winterizing the Tap in outdoor installations), improper
cleaning, proximity to bodies of saltwater, or accidental damage such as scuffs and scratches are not covered by this warranty. Seller
does not assume liability for labor charges, removal and reinstallation expenses, freight or postage charges, or injuries resulting
from a defective product. This warranty does not allow recovery of incidental or consequential damages such as loss of use,
property damage, or any other consequential damage and Seller accepts no liability for such damage. Seller does not assume any
responsibility other than to repair or replace the defective part(s) after Seller, upon its examination, has determined the product to
be defective and the defective part(s) are covered by the Limited Lifetime Warranty expressed in this warranty. Whether to repair or
replace the product shall be at the sole election of the Seller. In no event shall the liability of The Galley exceed the purchase price
of the Tap. The use of Plumber’s Putty will void this warranty. A non-corrosive epoxy silicone sealing compound may be used. Seller
hereby disclaims all other warranties, expressed or implied, other than those set forth in this warranty. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This
warranty gives you specific legal rights and you may also have other rights which vary from state to state.
These warranties are in effect for Seller’s Products purchased on January 1st, 2017 and thereafter. For warranty claims, please
contact your Galley Dealer, or you may write to:
The Galley, LLC.
Attn: Warranty Claims
12626 South Memorial Drive
Bixby, OK 74008
Please include the original receipt with a description of the problem, model number, store, date of purchase, your name, address
and telephone number.
1. GALLEY TAP LIMITED LIFETIME MECHANICAL WARRANTY —
2. GALLEY TAP LIMITED LIFETIME FINISH WARRANTY —
3. WARRANTY CONDITIONS AND LIMITATIONS —
4. WARRANTY CLAIMS —
Corporate Headquarters
The Galley, LLC.
12626 South Memorial Drive
Bixby, OK 74008
800.375.4255
thegalley.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
The Galley IBT-D-BSS Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
TOUGHBUILT TB-CT-31-A Operating instructions
-
Lynx LFK Installation guide
-
American Standard Shower Systems 1660.125 User manual
-
Kingston Brass HKS8981DKL Installation guide
-
Aquasanita AKVADUO 2663 Installation guide
-
-
Luxier BSH06-SC Installation guide
-
BLANCO 442036 Installation guide
-
-
