RAIN GUARD CU-0205 User manual

Brand: RAIN GUARD

Model: CU-0205

Type: User manual

This manual is also suitable for

CU-0105

Rainguard

Clear-Seal Acrylic

Clear-Seal

™

Acrylic

Urethane

technical data sheet

100% Urethane Water Repellent

Page 1 of 3Customer Service Help-Line 800.272.4647 RainguardPro.com

Description

Rainguard Clear-Seal Acrylic Urethane Sealer is

a single-component, self cross linking urethane/

acrylic sealer and nish coat for decorative

concrete, stone, and other masonry surfaces

Clear-Seal, a waterbased, low VOC, low odor

coating can protect your masonry against

chemical spills and staining agents, UV light, and

wear due to heavy foot and tire trafc.

Clear-Seal is formulated for use on horizontal or

vertical painted or unpainted concrete and wood

surfaces. It may be used as a clear sealer

on commercial, warehouse, or industrial oors,

residential or commercial garage spaces, brick

pavers, or other masonry surfaces.

Features

• Impact and wear resistant

• Resists hot tire pick-up

• Non-yellowing formulation

• Resistant to stains, acids, bases, gasoline,

alcohol and oil (vegetable and motor)

• Low odor

• Non-hazardous

• Resists UV rays

• Environmentally-friendly

• Water clean-up

• Excellent adhesion

• Fast dry time and cure time

Recommended Uses

• Brick

• Concrete

• EFIS or Cement Plaster

• Masonry Block

• Stucco

• Wood

• Clear protection on murals and painted

vertical surfaces

• Repellent of oil, gas, and other uids

Coverage Rates* (Theoretical)

*Extremely porous surfaces may require multiple coats

Substrate Sq Ft / Gallon

Porous Surface 200-300

Dense Surface 100-150

Description U/M Code

Clear-Seal Acrylic High Gloss 1 Gallon CU-0101

Urethane Quick Cure 2 Ounce SP-1300

Clear-Seal Acrylic High Gloss 5 Gallon CU-0105

Urethane Quick Cure 10 Ounce SP-1305

Clear-Seal Acrylic Low Gloss 1 Gallon CU-0201

Urethane Quick Cure 2 Ounce SP-1300

Clear-Seal Acrylic Low Gloss 5 Gallon CU-0205

Urethane Quick Cure 10 Ounce SP-1305

Rainguard

Clear-Seal Acrylic

Page 2 of 3Customer Service Help-Line 800.272.4647 RainguardPro.com

Application

1. Clear-Seal Acrylic Urethane Sealer should be

applied using either brush, t-bar, lamb’s wool

applicator, or most pump-up sprayers. We

do not recommend using a roller to apply, as

this may allow too much air, causing bubbles

to stay in the lm.

2. At time of application, moisture content of all

surfaces should be 30% or less as measured

with an electronic moisture meter.

3. Establish that air, surface and material

temperatures are above 40°f (4.4°C) and

at least 5°f above the dew point prior to

painting. Do not apply at temperatures below

40°f or when temperatures are expected

to drop below 40°f within 48 hours of

application. Do not apply if rain, snow, or

lower temperatures are expected within 48

hours. Do not apply if relative humidity is

greater than 80%.

4. Allow at least 1 hour or until tack-free before

applying a second coat.

Warranty

The information contained herein is offered in

good faith and is believed to be accurate. To be

eligible for a Rainguard Warranty the following

must occur:

1. A site visit must be conducted by an employee

or agent of Rainguard and a Field Inspection

Report completed.

2. A Warranty Application must be fully

completed by the applicator.

3. Field Inspection Report, Warranty Application,

and a copy of the distributor’s invoice must be

submitted to and approved by Rainguard.

This material is only warranted when applied in

accordance with the manufacturer’s guidelines

and warranty procedures. Without adherence to

these specic guidelines, no expressed or implied

warranty of this product is given. Please contact

Rainguard for additional information.

Inspection

Surface must be clean, dry, and free of grease,

paint, oil, dust, curing agents, or any foreign

material that will prevent proper adhesion. The

surface should be porous and be able to absorb

water. Relative humidity in the surface should

be below 80% (per ASTM F-2170). All moisture

should be kept away a minimum of 48 hours

before application and a min. of 48 hours after

installation. This includes sprinklers, rain, fog,

dew, etc.

Drying Time

Wait 24 Hours before opening up to light to

moderate trafc, and 72 Hours before heavy trafc.

Limitations

• Do not apply in temperatures below 50°F or

above 90°F.

• Do not apply on damp or moist surface as it

will whiten and may cause delamination.

• Do not allow any Rainguard products to freeze.

• Prior to coating previously sealed surfaces,

test a small area for adhesion.

• Ok for use as an Industrial Maintenance

Coating, Concrete Masonry Sealer, or Floor

Coating, anywhere in the United States,

including the South Coast Air Quality

Management District (SCAQMD).

• Please become familiar with local Air Quality

laws and regulations prior to applying this

coating. Rainguard bears no responsibility for

improper usage.

Test Panel

Always apply material to a mock wall or test panel.

Test wall or actual surface area to determine

acceptable color, surface porosity, application

rates and methods before starting general

application. It is the duty of the applicator to do a

test area to determine the surface is prepared for

general application of this coating. This adhesion

test can be done by applying a sample in an

inconspicuous area. Allow the sample to dry

and cure. Then cut the coating in a grid pattern

with vertical and horizontal lines cut into the lm.

Then place tape over the cut grid lines and wait

several minutes. Pull the tape up, if any material

delaminates, the surface is not properly prepared

for general application. If the sample is not altered

after removing the tape, the surface is sufciently

prepared for general application.

Precautions

Rainguard recommends the use of slip-resistant

aggregate in all coating or ooring systems that

may be exposed to wet, oily or greasy conditions.

These aggregates can be incorporated into the

materials using different methods to achieve

varying proles and degrees of slip-resistance.

However, textured surfaces can be slippery under

certain conditions. This type of activity on the

ooring surface, maintenance procedures and

type of footwear may all be factors to consider

when deciding the degree of slip-resistance

needed for given area. Rainguard or its sales

agents will not be responsible for injury incurred

in a slip and fall situation. It is the end users’

responsibility to provide for their own safety and to

determine the suitability of these coatings for their

particular application.

Rainguard

Clear-Seal Acrylic

Page 3 of 3Customer Service Help-Line 800.272.4647 RainguardPro.com

Material Type Water Based Urethane

Volume Solids 31%

Color of Material Of-White Emulsion in can

Odor Slight Latex Smell

V.O.C. <50 g/L V.O.C. Compliant

Gloss Level 20 - 25 @ 60°

Flash Point Non-Flammable

pH Value Approximately 7.5

Viscosity 9.6 Seconds No. 4 Ford Cup

Weight Approximately 8.5 lbs./Gal.

Surface Dry/Recoat Approx. 1 Hour

Full Chemical Cure 24-72 Hours

Technical Data

RAIN GUARD CU-0205 User manual

Brand: RAIN GUARD

Model: CU-0205

Type: User manual

This manual is also suitable for

CU-0105

Download PDF

report

RAIN GUARD CU-0205 User manual

This manual is also suitable for

RAIN GUARD CU-0205 User manual

Related papers

Other documents