AGFEO DECT 50 User manual

Category
Telephones
Type
User manual
1
Bedienung
DECT 50
User Guide
System DECT
About this User Guide
This user manual is intended for the telephone system with the firmware installed at the time
of shipment. Should the telephone or the telephone system be updated with new firmware
made available from the manufacturer then some sections of the user guide may no longer be
applicable.
The display diagram in this user guide are only partly shown and may differ from the real
display of the DECT 50 handset.
- Only use the battery which has been approved for use with the handset (3,7V 1.0Ah).
- Only exchange battery of the same type or similar type recommended by the
manufacturer.
- The battery will get warm during the charging process, this is normal.
- Do not use any other charging device other than the designated charging cradle.
- Do not use the handset in the rain, bath tub or handle with wet hands.
- Take care that the charging contacts will not get in contact with other conductive material.
- In thunderstorms it is recommended to disconnect the unit from the mains supply.
- This is a rechargeable product. In day to day use it is normal for the unit to get warm.
Therefore it is advisable not to place the product on antique-, veenered or wooden surfaces.
- To clean the product use a damp cloth (not wet) or an antistatic cloth. Never use a dry cloth
as this could staticly charge the unit. Never spray any cleaning agents directly on the
handset or the base unit.
- Phone calls (including emergency calls) are only possible if the DECT S0 Base plus and the
telephone system are connected to power. NO calls can be made in case of a power failure.
BATTERIES AND RECHARGEABLE BATTERIES
If your product contains batteries or rechargeable batteries, then these must be disposed of at
designated collection points.
Safety Notice:
3
DECT 50
Table of Contents
Introduction
Safety Notice: ............................................................................................................................. 2
About this User Guide ................................................................................................................ 2
Introduction ................................................................................................................................5
User Instructions ....................................................................................................................... 5
Commissioning
The AGFEO DECT 50................................................................................................................... 6
Insert Battery ............................................................................................................................. 7
Using the DECT 50 for the first time .......................................................................................... 7
DECT 50 Switch On / Off ............................................................................................................ 8
Register DECT 50 to an AGFEO DECT-S0-Base plus .................................................................. 8
Base Settings
Display Area of DECT 50 ............................................................................................................. 9
Information Display of DECT 50 .................................................................................................. 9
Select Symbols Displayed .......................................................................................................... 10
Symbols ..................................................................................................................................... 11
Symbols ..................................................................................................................................... 12
Feature Status Indication .......................................................................................................... 13
Set Ringer Volume and Vibration Alarm.....................................................................................14
Ringer Sound.............................................................................................................................15
Setting Handsfree Volume ......................................................................................................... 16
Handset Volume ........................................................................................................................17
Handsfree Microphone Settings ................................................................................................18
Handset Microphone Settings ...................................................................................................19
Call Log Setting ......................................................................................................................... 20
Keypad Lock On / Off .................................................................................................................20
Making a Call
Calling using "Direct" Trunk Seizure .........................................................................................21
Calling without "Direct" Trunk Seizure ......................................................................................22
Redialling ..................................................................................................................................23
Answer a Call ............................................................................................................................23
Call Log .....................................................................................................................................24
Calling a telephone number from the Call Log ..........................................................................24
Delete one entry from the Call Log ............................................................................................24
Delete all entries........................................................................................................................24
Store Phone Number from Call Log to System Phone Book .....................................................25
Call History ................................................................................................................................26
Dialling a number from the Call History .................................................................................... 26
Store phone number from Call History to System Phone Book.................................................26
Caller ID ....................................................................................................................................27
Adjust Handset Volume During Call ..........................................................................................27
Handsfree..................................................................................................................................27
DECT 50 Internal Phone Book ...................................................................................................28
Enter Name ..............................................................................................................................28
Store Entry ................................................................................................................................28
Find Entry.................................................................................................................................. 29
Delete Entry ...............................................................................................................................29
4
DECT 50
Table of Contents
Dialling from the Phone Book ...................................................................................................29
Edit Entry ..................................................................................................................................30
The Phone Book of the Telephone System .................................................................................30
Change Mode of Retrieval ..........................................................................................................31
Retrieve Phone Number from System Phone Book (Vanity)......................................................31
Retrieve Phone Number from System Phone Book (Alphabetical) ............................................32
Retrieve Phone Number from System Phone book (Numerical) ...............................................32
Advanced Settings
Other Settings of DECT 50 .........................................................................................................33
Select Base ................................................................................................................................33
Delete Base ...............................................................................................................................34
Automatic Keypad Lock .............................................................................................................35
Automatic Call Answering .........................................................................................................35
Automatic Call Answering on Removal of DECT 50 from Charging Cradle ...............................36
Do Not Disturb (DND) ................................................................................................................36
Programming Function Buttons...............................................................................................37
Recall Function / Function Key .................................................................................................38
Function Buttons - available programmable Functions (Overview) ...........................................39
Function Buttons - available programmable Functions (Overview) ...........................................40
Pairing - the DECT 50 as an intelligent Cordless Phone Receiver .............................................41
Pairing Setup.............................................................................................................................41
Pairing Undo .............................................................................................................................41
Important Information regarding Pairing Function ...................................................................42
Status Display
Meter Mode ...............................................................................................................................42
Display Software Version ...........................................................................................................43
Technical Data ...........................................................................................................................43
5
DECT 50
The AGFEO DECT 50 is designed in connection with an AGFEO DECT-S0 Base plus to be
operated on an AGFEO ISDN Telephone System. The AGFEO DECT-S0-Base plus must have a
firmware version of 3.0 or higher.
The DECT 50 can be operated (at the time of going to press) on the following
AGFEO ISDN-Telephone Systems:
- ISDN Telephone Systems AS 43, AS 45, AS 200 IT from firmware 8.2
- ISDN Telephone Systems AS 281 All-In-One, AS 35, AS 35 All-In-One from
firmware 8.2
Information regarding firmware upgrades can be obtained via your dealer.
AGFEO GmbH & Co. KG will not be accept any liability for damages resulting from improper
use of the DECT 50.
Congratulation on the purchase of the AGFEO DECT 50 cordless telephone!
With this AGFEO premium product you have selected the latest technology of the cordless
system telephone generation.
It will enable you to operate via the soft keys, the from the telephone system managed home
automation, the common answering machine and extensive AGFEO system functions.
Furthermore you may program the most commonly used functions directly into the function
buttons and manage the systems internal phone book.
The pairing function will even further enhance the easy to operate System Phone AGFEO ST
40, which after only using it once you would not like to miss.
The graphical user interface and intuitive menu driven user guidance will make the
possibilities of AGFEO products a child's play!
Introduction
User Instructions
6
DECT 50
The AGFEO DECT 50
AGFEO
TUV
WXYZPQRS
GHI
JKL
MNO
ABC
DEF
DECT 50
R
1
2
3
6
5
4
7
8
9
0
#
Pick Up / Hang Up
Headset Connection
Volume Control
Display
Softkey Left
Changes pending
on Mode of Operation
Softkey Right
Changes pending
on Mode of Operation
Recall Button to
Abort Programming
in System Menu
Navigation Button
Microphone
Alphanumeric Keypad
7
DECT 50
Using the DECT 50 for the first time
Insert the rechargeable battery into the handset (see above).
Connect the enclosed power supply unit to the charging cradle and plug the power supply into
the mains socket.
Remove the protection film from the display and insert the handset into the charging cradle to
charge the batteries.
The charging symbol will be shown in the display to indicate that the DECT 50 is now being
charged. Once the batteries are completely charged the charging symbol will change to green.
Now continue to register the DECT 50 (refer to page 8).
Insert Battery
To open the battery compartment, press the cover with your thumb and slide this towards the
charging contacts, then lift the cover upwards.
Insert the battery in such a way that the contacts of the battery touch the spring contacts of
the handset.
To refit the cover follow the steps of opening in reverse order.
Approved Rechargeable Batteries:
Only the enclosed battery is approved for use with this handset. Do not use any other battery.
8
DECT 50
DECT 50 Switch On / Off
Register DECT 50 to an
AGFEO DECT-S0-Base plus
Please follow the instruction below to register the DECT 50 to a Base Station:
Ensure that the handset to be registered in close proximity of the base unit. Activate the
registration mode as described in the user manual of your DECT S0-Base plus. Afterwards
continue with your DECT 50 as detailed below:
AGFEO
DECT 50
Menu
Status
Phone Book
Setup
AGFEO
DECT 50
Setup
Configuration
Base Station
Repeater
Language
AGFEO
DECT 50
Base Station
Select Base
Register Base
Delete Base
AGFEO
DECT 50
Search Base
000222111000
Press for 2 seconds
"Setup"
"Base Station"
"Register Base"
Select required Base
Select the desired
memory location
Enter PIN
default:
2580
Select
Select
Select
Select
Select
Base Stations which are in registration mode will now be displayed.
The handset will be registered to the base shortly.
Select
z
Press the left softkey to switch the DECT 50 to on.
To switch the DECT 50 off:
Press for 2 seconds
SelectInfo
Menu
9
DECT 50
Display Area of DECT 50
X
i
A
//
External ISDN-line. One line (one B-channel) is in use. On an incoming ringing call the
x will be displayed in colour.
Internal ISDN-line. One line (one B-channel) is in use.
Analogue Trunk Line. One line is busy.
The line is faulty, the symbol will be indicated in red.
Display of features set.
Up to 9 features can
be displayed. A
description of the
various symbols can be
found on page 10. The
activation will be
shown by a dot, which
will be displayed in a
different colour
depending on status
(see page 13).
Extension status
display, busy on a call
or ringing. Ringing
extension numbers
will be displayed in
colour (Status only
displayed if handset
is off hook).
Status of internal
and external S0s,
each S0 one box.
Reception display,
the DECT 50 is
connected to a
DECT S0 Base Unit.
If the battery charge is low
the red charging symbol will
be displayed and in addition
a warning tone will be
heard. Return the DECT 50
into the charging cradle.
The charging symbol will
now be displayed in white,
indication that the battery is
charging.
Handsfree
mode is
enabled
Handset is
muted.
Keypad is
locked
Information Display of DECT 50
The status information of the handset will be displayed by pressing the left softkey ("Info"
button) when the handset is idle. This will display the time & date, extension number - and
extension name of the DECT 50. If the DECT 50 is paired with another phone then it will also
display which telephone has been paired with the DECT 50.
Pressing the softkey again ("More" button) will display the features allocated to each of the
navigation buttons.
By pressing the right softkey ("Stop" button) the information display will be exited.
AGFEO DECT 50
Info Menu
08:30
(
(
.
)
)
Extn. 11
AGFEO DECT 50
Speaker
08:30
(
(
.
)
)
WK22 Mo 29.May 08
11 22 34 16
i i XX ii XX
D
)
)
x
Handset status.
Red during dialling
preparation, green
if the handset is
off hook.
10
DECT 50
Select Symbols Displayed
Up to 9 symbols can be displayed at the same time. All available symbols may be switched on.
A symbol set to "On" to be displayed will be indicated by an X or a dot.
Press briefly
"Phone Settings"
"Status"
"Icon Display"
Select symbol to be displayed
Switch on
or
Switch off
Change
On
Off
AGFEO
DECT 50
Menu
1 System Features
2 Phone Settings
3 Buttons/Ext Name
AGFEO
DECT 50
Phone Settings
1 Tone Ringer Vol
2 Ringer Sound
4 Remote Seizure
AGFEO
DECT 50
Status
1 S0-Status
2 Internstatus
5 DisplayName in B
Menu
2
9
AGFEO
DECT 50
Icon Display
Appointment Call
7
If no X or dot is within the symbol, then this means that the symbol is not
switched on. The dot means that the symbol is switched on and will be
displayed. An X does indicate that the symbol is switched on but cannot be
displayed. This could be due to the following:
- There are more than 9 symbols switched on.
- The function which will be indicated by this symbol is not programmed for
your DECT 50 (such as Diversion or Call Filter)!
TIP:
You may also set these symbols via TK-Suite Set. To do so go to "Phone Settings/System
Phone Setting" and open the TAB "Display".
11
DECT 50
Symbols
If you click on "Menu" you can scroll through the various features and if so required switch
these on, off or undo them. The symbol selected by the navigation button will be highlighted.
The following pages will give an overview of the features depicted by the various symbols.
Enable/Disable the sending of Caller ID (Withhold Number)
Function Symbol
Switching the Sensors of the Telephone System.
Switching the programmed Relays of the Telephone System.
Enable/Disable Night Service. All assigned lines in the incoming call
distribution table for your extension will be changed.
Diversion program and/or switch on/off.
Wake Up Calls program and/or switch on/off.
Telephone Lock to protect phone against unauthorised use.
Switching of configured EIB objects.
Enable/Disable Do Not Disturb.
12
DECT 50
Symbols
Function Symbol
This will recall the Telephone Systems programming menu. Here you
may program settings within the telephone system.
NOTE:
If this symbol is not visible, then the settings as described
on pages 14 to 20 are not available to your phone!
Call Waiting this feature can be enabled or disabled so callers may wait for
you if you are already on another call.
Programming and switching of Appointment Reminder Calls.
Enable/Disable Call Filter. This feature allows you to carry out a preset
action on receiving calls from a specific- or withheld telephone number.
You may for example reject calls, transfer calls to an answering
machine, divert - or break through an already established call.
Switching the Answering Machine of your ST 40 on or off. This will only be
possible if the DECT 50 is paired to an ST 40 with answering machine module.
13
DECT 50
Green Yellow Red
All Diversions are
enabled.
Wake Up Call enabled.
Telephone Lock is on.
Emergency Call /Direct
Call or Auto Dialling is
enabled, providing it is
programmed in the
telephone system.
All relays are enabled.
Do Not Disturb is
enabled for all calls.
Night service is enabled
for all lines for which
your DECT 50 is
authorised to use.
Withhold own number
enabled
All Answering machine
announcements are
enabled.
Appointment set.
Call Filters enabled.
All Sensors are enabled.
Call Waiting enabled.
All switchable objects
are enabled.
No Diversions are
enabled.
All relays are disabled .
Do Not Distrub is only
enabled for external or
internal calls.
Night service is only
enanbled for some
lines.
Answering machine
announcements are
enabled.
Some Sensors are
enabled.
Some switchable
objects are enabled.
Snooze enabled. Will
ring every 10 mins. up
to an hour or until
disabled.
Appointment expired.
Feature Status Indication
14
DECT 50
Set Ringer Volume and Vibration Alarm
Press briefly
"Phone Settings"
"Tone Ringer Vol"
Select required level
If you want to set the Vibration Alarm:
"Vibration Alarm"
Switch On
After settings are completed press
"Store".
Change
On
AGFEO
DECT 50
Menu
1 System Features
2 Phone Settings
3 Buttons/Ext Name
AGFEO
DECT 50
Phone Settings
1 Tone Ringer Vol
2 Ringer Sound
4 Remote Seizure
Icon Anzeige
AGFEO
DECT 50
Tone Ringer Vol
3 from 0-7
<> Digit or + -
Vibration Alarm
Menu
2
1
Icon Anzeige
AGFEO
DECT 50
Tone Ringer Vol
3 from 0-7
<> Digit or + -
Vibration Alarm
Store
z
=> =>
15
DECT 50
Ringer Sound
Press briefly
"Phone Settings"
"Ringer Sound"
Select "External-“, „Internal-“ or „Door Phone-“ Call
Select Melody
Change
AGFEO
DECT 50
Menu
1 System Features
2 Phone Settings
3 Buttons/Ext Name
AGFEO
DECT 50
Phone Settings
1 Tone Ringer Vol
2 Ringer Sound
4 Remote Seizure
AGFEO
DECT 50
Rhythm/Melody
<> Ringer Type
Ringer Sound
Extension Call
Menu
2
2
AGFEO
DECT 50
Rhythm/Melody
1 from 1-10
<> Digit or +-
Store
You may select one of 10 different Ring Tones:
Change
=> =>
16
DECT 50
Setting Handsfree Volume
The handsfree volume of your DECT 50 has a 7 step adjustment:
Press briefly
"Phone Settings"
"AcousticSettings"
"Handsfree Volume"
Select required level
Change
AGFEO
DECT 50
Menu
1 System Features
2 Phone Settings
3 Buttons/Ext Name
AGFEO
DECT 50
Phone Settings
1 Tone Ringer Vol
2 Ringer Sound
4 Remote Seizure
AGFEO
DECT 50
AcousticSettings
1 Handsfree Volume
2 Handset Volume
4 Handsfree Mike
Menu
2
5
AGFEO
DECT 50
Handsfree Volume
3 from 1-7
<> Digit or +-
Store
z
1
=> =>
17
DECT 50
The handset volume of your DECT 50 has a 5 step adjustment:
Press briefly
"Phone Settings"
"AcousticSettings"
"Handset Volume"
Select required level
Change
AGFEO
DECT 50
Menu
1 System Features
2 Phone Settings
3 Buttons/Ext Name
AGFEO
DECT 50
Phone Settings
1 Tone Ringer Vol
2 Ringer Sound
4 Remote Seizure
AGFEO
DECT 50
AcousticSettings
1 Handsfree Volume
2 Handset Volume
4 Handsfree Mike
Menu
2
5
AGFEO
DECT 50
Handset Volume
3 from 1-5
<> Digit or +-
Store
z
2
Handset Volume
=> =>
18
DECT 50
Handsfree Microphone Settings
The sensitivity of the handsfree microphone of your DECT 50 has a 5 step adjustment:
Press briefly
"Phone Settings"
"AcousticSettings"
"Handsfree Mike"
Select required level
Change
AGFEO
DECT 50
Menu
1 System Features
2 Phone Settings
3 Buttons/Ext Name
AGFEO
DECT 50
Phone Settings
1 Tone Ringer Vol
2 Ringer Sound
4 Remote Seizure
AGFEO
DECT 50
AcousticSettings
1 Handsfree Volume
2 Handset Volume
4 Handsfree Mike
Menu
2
5
AGFEO
DECT 50
Handsfree Mike
3 from 1-5
<> Digit or +-
Store
z
4
=> =>
19
DECT 50
Handset Microphone Settings
The sensitivity of the handset microphone of your DECT 50 has a 5 step adjustment:
Press briefly
"Phone Settings"
"AcousticSettings"
"Handset Mike"
Select required level
Change
AGFEO
DECT 50
Menu
1 System Features
2 Phone Settings
3 Buttons/Ext Name
AGFEO
DECT 50
Phone Settings
1 Tone Ringer Vol
2 Ringer Sound
4 Remote Seizure
AGFEO
DECT 50
AcousticSettings
1 Handsfree Volume
2 Handset Volume
4 Handsfree Mike
Menu
2
5
AGFEO
DECT 50
Handset Mike
3 from 1-5
<> Digit or +-
Store
z
5
=> =>
20
DECT 50
Call Log Setting
Press briefly
"Phone Settings"
"Call Log"
"External"
Select required setting by pressing relevant number
"Extension"
Select extension: Switch on or off as required
Change
AGFEO
DECT 50
Menu
1 System Features
2 Phone Settings
3 Buttons/Ext Name
AGFEO
DECT 50
Phone Settings
1 Tone Ringer Vol
2 Ringer Sound
4 Remote Seizure
AGFEO
DECT 50
Call Log
1 External
2 Extension
Menu
2
AGFEO
DECT 50
External
1 off
2 Including Number
3 from Phone Book
z
Change
=> =>
1
2
AGFEO
DECT 50
Call Log
1 External
2 Extension
Keypad Lock On / Off
AGFEO
DECT 50
08:30
(
(
.
)
)
You can lock the keypad of your DECT 50 in order not to
press any buttons accidentally.
Press and hold the „*“button until a key symbol will be
shown in the display. Press and hold again the "*" button
to switch the keypad lock off.
The keypad lock will switch off automatically on an
incoming call and is reactivated once the call has ended.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

AGFEO DECT 50 User manual

Category
Telephones
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages