HP 9315M User manual

Brand: HP

Model: 9315M

Category: Network switch modules

Type: User manual

This manual is also suitable for

ProCurve 9315M

Software release 07.8.04a supersedes earlier software releases in the 07.x software branch. (For information

about software branches and minimum release requirements for management module support, refer to “Software

Branches” on page 3.)

The 07.8.04a release notes provide information on the following items:

• New hardware and software enhancements introduced with software release 07.8.04a

• Known issues in software release 07.8.04a

• Procedure for upgrading the software code on ProCurve 9304M, 9308M, and 9315M Routing Switches with

M2, M4, or EP Redundant Management modules. See “Upgrading Software on an M2, M4, or EP

Management Module to Release 07.8.04a” on page 7.

• General procedures, usage information, and helpful notes for operating and managing ProCurve routing

switches

• Software fixes in release 07.8.04a and earlier releases

Descriptions of the enhancements in release 07.8.00 are included in the manuals for the 07.8.00 release. If you

purchased a Redundant Management module with software version 07.8.00 or greater installed, the CD shipped

with the module includes the 07.8.00 manuals.

If you need to access ProCurve product documentation, refer to “Downloading the Latest Software and

Documentation” on page 3 for information on how to download PDF versions of the latest manuals.

NOTES:

Software Update Notice: Check the ProCurve Website frequently for free software updates for various ProCurve

switch products. (Refer to “Downloading the Latest Software and Documentation” on page 3.)

Mini-GBIC ports: Hewlett-Packard offers and supports only mini-GBICs having a ProCurve label (with product

number J4858B, J4859B, or J4860B) for use with the following modules:

- J4856A ProCurve 9300 Mini-GBIC Module

- J4857A ProCurve 9300 Mini-GBIC Redundant Management Module

- J4885A ProCurve 9300 EP 8-port Mini-GBIC Redundant Management Module

- J4894A ProCurve 9300 EP 16-port Mini-GBIC Module

- J8177B ProCurve Gigabit-copper mini-GBIC is supported for use in only the EP modules (J4885A and J4894A)

Use of other brands of mini-GBICs is not supported.

Flash Images: The flash image files for this software release differ depending on the type of management module

you use. Refer to “Boot Code Requirements for ProCurve Software” on page 5.

SNMP: Starting with software release 05.2.16, the software does not have a default read-write SNMP community.

If you use the default community name “private” as the password for web management access or for read-write

access through a network management application, you need to use the CLI to add the read-write community

string first.

Devices Without Redundant Management: For information about how to upgrade software on the ProCurve

9304M and ProCurve 9308M routing switches without redundant management, refer to the latest 6.6.x release

notes. (See “Downloading the Latest Software and Documentation” on page 3.)

Release Notes

Version 07.8.04a Operating System

for the ProCurve 9304M, 9308M, and 9315M Routing Switches

with Redundant Management (M2, M4, EP, and T-Flow), September 2008

Release Notes for 07.8.04a

ment Company, L.P. The information contained herein

is subject to change without notice.

Publication Number

5991-4722

September 2008

Applicable ProCurve 9300 (Current) Products

9304M Routing Switch . . . . . . . . . . . . . . . . . . (J4139A)

9308M Routing Switch . . . . . . . . . . . . . . . . . . (J4138A)

9315M Routing Switch . . . . . . . . . . . . . . . . . . (J4874A)

EP 10/100-TX RJ-45 Module . . . . . . . . . . . . . (J4881B)

EP 10/100-TX Telco (RJ-21) Module . . . . . . . (J4889B)

EP Mini-GBIC RM Module . . . . . . . . . . . . . . . (J4885A)

EP Mini-GBIC Module. . . . . . . . . . . . . . . . . . . (J4894A)

EP 100/1000-T Module. . . . . . . . . . . . . . . . . . (J4895A)

2-Port 10 Gigabit Ethernet Module . . . . . . . . (J8174A)

EP 100Base-FX Module. . . . . . . . . . . . . . . . . (J8178A)

Gigabit-SX-LC Mini-GBIC . . . . . . . . . . . . . . . (J4858B)

Gigabit-LX-LC Mini-GBIC . . . . . . . . . . . . . . . (J4859B)

Gigabit-LH-LC Mini-GBIC . . . . . . . . . . . . . . . (J4860B)

1000Base-T Mini-GBIC. . . . . . . . . . . . . . . . . . (J8177B)

10 Gigabit Ethernet LR Optic . . . . . . . . . . . . . (J8173A)

10 Gigabit Ethernet SR Optic . . . . . . . . . . . . (J8175A)

10 Gigabit Ethernet ER Optic . . . . . . . . . . . . (J8176A)

9304M/9308M Redundant Power Supply. . . . (J4147A)

9315M Redundant Power Supply. . . . . . . . . . (J4875A)

Trademark Credits

Microsoft®, Windows®, and Windows NT® are

trademarks of Microsoft Corporation. Adobe® and

Acrobat® are trademarks of Adobe Systems

Incorporated.

Disclaimer

The information contained in this document is subject to

change without notice.

HEWLETT-PACKARD COMPANY MAKES NO

WARRANTY OF ANY KIND WITH REGARD TO THIS

MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. Hewlett-

Packard shall not be liable for errors contained herein or

for incidental or consequential damages in connection

with the furnishing, performance, or use of this material.

The only warranties for HP products and services are set

forth in the express warranty statements accompanying

such products and services. Nothing herein should be

construed as constituting an additional warranty. HP shall

not be liable for technical or editorial errors or omissions

contained herein.

Hewlett-Packard assumes no responsibility for the use or

reliability of its software on equipment that is not furnished

by Hewlett-Packard.

Warranty

See the Customer Support/Warranty booklet included with

the product.

A copy of the specific warranty terms applicable to your

Hewlett-Packard products and replacement parts can be

obtained from your HP Sales and Service Office or

authorized dealer.

Hewlett-Packard Company

8000 Foothills Blvd.

Roseville, CA 95747-5551

USA

http://www.procurve.com

iii

Release Notes for 07.8.04a

Contents

Terminology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Product Documentation for Software Release 07.8.04a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Downloading the Latest Software and Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Software Branches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Software Requirements for Management Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Software Supported on ProCurve Routing Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Boot Code Requirements for ProCurve Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Upgrading Software on an M2, M4, or EP Management Module to Release 07.8.04a. . . . . . . . . . . . . . . . 7

Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Upgrading to Software Release 07.8.04a: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

A. Upgrading Boot Code on a Management Module to Version 07.06.05 . . . . . . . . . . . . . . . . . . . . . . 8

B. Upgrading Software on a Management Module From a Release Earlier than 07.6.01b . . . . . . . . . 8

C. Upgrading Software on a Management Module From Release 07.6.01b or Greater. . . . . . . . . . . . 9

Using SNMP to Upgrade Software on a Management Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Upgrading the FPGA on a 10 Gigabit Ethernet Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Using Different Combinations of Management Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Non-Redundant Management on ProCurve 9304M and ProCurve 9308M Routing Switches . . . . . . . . . 13

Maximum Size of Startup-Config and Running-Config Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Removing a Module from an Active Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Configuring the ProCurve 9315M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Minimum Software Release Supported. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Inserting or Removing an EP Module on a ProCurve 9315M. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Slot Locations for Redundant Management Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

MAC Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Server Trunk Groups. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

VLANs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Enhancements and Configuration Notes in 07.8.03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Software Fixes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Known Issues in 07.8.03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

ProCurve 9300M Series Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Release Notes for 07.8.04 Terminology

Terminology

The following table defines basic product terms used in ProCurve routing switch documentation.

Product Documentation for Software Release 07.8.04a

Software release 07.8.04a includes all of the features in release 07.8.00a, plus several new features.

• For documentation on the features in 07.8.04a that were available in earlier releases, refer to the product

documentation set identified for “Software Version 07.8.00a”.

Table 1 describes the main topics covered in the ProCurve Routing Switch documentation set. If you do not

already have a PDF version of the 07.8.00a documentation set, refer to “Downloading the Latest Software and

Documentation” on page 3.

Term Definition

chassis device or chassis A routing switch that accepts optional modules or power supplies. The

ProCurve 9315M, ProCurve 9304M, and ProCurve 9308M routing switches

are chassis devices.

EP (Enhanced Performance)

and Standard

Routing switches can be EP or Standard devices, depending on whether the

management module is an EP or Standard (M2 or M4) module. For a listing of

ProCurve routing switches and their product numbers, see Table 4 on page 5.

routing switch or router A Layer 3 device that switches and routes network traffic. The term router is

sometimes used in this document in descriptions of a routing switch’s Layer 3

routing protocol features.

switch A Layer 2 device that switches network traffic.

ProCurve 9300# An example Command Line Interface (CLI) prompt. Actual prompts show the

product number for the routing switch, such as ProCurve 9300#.

Product Documentation for Software Release 07.8.04a Release Notes for 07.8.04

Table 1: Where To Get More Information

Title Contents

Installation and Basic

Configuration Guide

• Installation

• Basic Features

• System (SNMP, SNTP, Syslog, broadcast and multicast throttling)

• Port configuration (speed, mode)

• Layer 2 (MAC table parameters, MAC filters, broadcast and multicast

filters, port locks)

• Parameter table resizing

• Port monitoring

• Link Aggregation

• Spanning Tree Protocol

• Virtual LANs

• Layer 2 Multicast

• Base Layer 3

• Upgrading Software (Important: See also “Upgrading Software on an M2,

M4, or EP Management Module to Release 07.8.04a” on page 7 in this

document.)

• Hardware Specifications and RFCs

Security Guide • Security (passwords, user accounts, AAA, RADIUS, and TACACS/TACACS+)

• Secure Shell (SSH)

• Denial of Service Protection

Advanced Configuration and

Management Guide

•QoS

•ACLs

• EP rate limiting

• Standard rate limiting

•IP

•RIP

• IP Multicast

• OSPF

•BGP4

• Network Address Translation

• VRRP and VRRPE

•IPX

• AppleTalk

Command Line Interface

Reference

Syntax information for all CLI commands.

Diagnostics Guide • Diagnostic commands

• Backplane debugging commands

• Changing CAM partitions

Release Notes for 07.8.04 Downloading the Latest Software and Documentation

Downloading the Latest Software and Documentation

You can download software version 07.8.04a and the latest routing switch product documentation from the

ProCurve website as described below.

To Download a Software Version:

1. Go to the ProCurve website at http://www.procurve.com.

2. Click on software (in the sidebar).

3. Under “latest software”, click on switches.

NOTE: If you are downloading software for the ProCurve 9304M or ProCurve 9308M, select the option that

matches the type of management module(s) you are using in the routing switch—with redundant management or

without redundant management.

To Download Product Documentation:

For the latest version of product documentation for ProCurve routing switches:

Go to the ProCurve website at http://www.procurve.com.

2. Click on technical support, then manuals.

3. Click on the name of the product for which you want manuals.

4. On the page listing the manuals, find the latest manuals under the heading “For software version 7.8.00a”.

You will need the Adobe® Acrobat® Reader (version 4.0 or greater) to view or print the manuals.

Software Branches

Starting with software releases 06.6.28 and 07.1.10, ProCurve offers the software branches described in Table 2:

Table 2: Software Branches

Software Release Includes: Operates on:

06.6.28 and later 06.x

releases

Bug fixes ProCurve 9304M and ProCurve 9308M routing

switches without redundant management (that is,

with M1 modules)

ProCurve 6308M-SX routing switch

ProCurve 6208M-SX switch

07.1.10 and later 07.1.x

releases

Bug fixes, new features, and

enhancements to existing

features

ProCurve 9304M and ProCurve 9308M routing

switches with redundant management (M2

modules)

07.5.04 release Bug fixes, new features, and

enhancements to existing

features

ProCurve 9304M, ProCurve 9308M, and ProCurve

9315M routing switches with redundant

management (M2 and M4 modules)

07.6.00 and 07.6.01b

releases

Bug fixes, new features, and

enhancements to existing

features

ProCurve 9304M, ProCurve 9308M, and ProCurve

9315M routing switches with redundant

management (M2, M4, EP, and T-Flow) and 1-port

10GB modules

07.6.04 release

07.7.01 release

Bug fixes, new features, and

enhancements to existing

features, including support

for the 2-port 10GB module

ProCurve 9304M, ProCurve 9308M, and ProCurve

9315M routing switches with redundant

management (M2, M4, EP, and T-Flow) and 2-port

10GB modules

Software Requirements for Management Modules Release Notes for 07.8.04

Software Requirements for Management Modules

Table 3 shows the minimum software releases required to run redundant management modules.

Table 3: Minimum Software Requirements for Management Modules

07.7.01b release Bug fixes, 07.7.01 features

and enhancements to

existing features, and a new

procedure for upgrading

software code

ProCurve 9304M, ProCurve 9308M, and ProCurve

9315M routing switches with redundant

management (M2, M4, EP, and T-Flow) and 2-port

10GB modules

07.8.00a release Bug fixes, new 07.8.00a

hardware and software

features, and enhancements

to existing features

ProCurve 9304M, ProCurve 9308M, and ProCurve

9315M routing switches with redundant

management (M2, M4, EP, and T-Flow) and 2-port

10GB modules

Minimum Software

Release Required

ProCurve 9300 Series Redundant Management Modules Supported

07.1.10

Supported only on

ProCurve 9304M and

9308M

J4845A ProCurve 9300 GigLX Redundant Management Module (8-port, M2)

J4846A ProCurve 9300 GigSX Redundant Management Module (8-port, M2)

J4847A ProCurve 9300 Redundant Management Module (0-port, M2)

07.1.19

Supported only on

ProCurve 9304M and

9308M

All of the redundant management modules supported for release 07.1.10

J4857A ProCurve 9300 Mini-GBIC Redundant Management Module (8-port, M4)

07.5.04

Supported on ProCurve

9304M, 9308M, and

9315M

All of the redundant management modules supported for release 07.1.19

J4879A ProCurve 9300 T-Flow Redundant Management Module

07.6.00

Supported on ProCurve

9304M, 9308M, and

9315M

All of the redundant management modules supported for release 07.5.04

J4885A ProCurve 9300 EP Mini-GBIC Redundant Management Module

Table 2: Software Branches

Software Release Includes: Operates on:

Release Notes for 07.8.04 Software Supported on ProCurve Routing Switches

Software Supported on ProCurve Routing Switches

Table 4 shows the software releases supported on each ProCurve routing switch.

Boot Code Requirements for ProCurve Software

To run a software release on a ProCurve routing switch, you must use the minimum version of boot code for each

software image described in Table 5.

Table 4: Software Releases Supported on ProCurve Routing Switches

Routing Switch Software Releases Supported

M2 or M4

Redundant Mgmt

H2R05216.BIN

H2R06605.BIN

H2R06616.BIN

H2R07110.BIN

H2R07119.BIN

H2R07122.BIN

H2R07124.BIN

M2 or M4

Redundant Mgmt

H2R07504.BIN

H2R07600.BIN

H2R07601.BIN

H2R07604c.BIN

H2R07701b.BIN

H2R07800a.BIN

H2R07801d.BIN

H2R07803.BIN

M1 Router

Code only

HPR05216.BIN

HPR06605.BIN

HPR06616.BIN

HPR06628.BIN

HPR06633.BIN

HPR06636.BIN

M1 Switch

Code only

HPS05216.BIN

HPS06605.BIN

HPS06616.BIN

HPS06628.BIN

HPS06633.BIN

HPS06636.BIN

ProCurve 9315M (J4874A)

Routing Switch with EP or

Standard (M2 or M4)

Redundant Management

Module(s)

No Yes No No

ProCurve 9304M (J4139A)

and 9308M (J4138A) Routing

Switches with EP or Standard

(M2 or M4) Redundant

Management Module(s)

Yes Yes No No

ProCurve 9304M (J4139A)

and 9308M (J4138A) Routing

Switches without Redundant

Management (with M1

Management Module)

No No Yes No

ProCurve 6308M-SX (J4840A)

Routing Switch

No N/A Yes No

ProCurve 6208M-SX (J4841A)

Switch

No N/A No Yes

First software release to support the ProCurve 9315M routing switch and the J4879A T-Flow module

First software release to support the EP (Enhanced Performance) modules.

Boot Code Requirements for ProCurve Software Release Notes for 07.8.04

Table 5: Boot Code Requirements

Routing

Switch

Modules Software Image Minimum Boot Code

Required

ProCurve 9304M

ProCurve 9308M

With one of the following

modules (without

Redundant Management):

J4141A 10/100

J4144A Gigabit SX

J4146A Gigabit 4LX/4SX

HPR06636.bin

M1B07108.bin or greater

recommended

ProCurve 9304M

ProCurve 9308M

ProCurve 9315M

With any one or two of the

following Redundant

Management: modules

J4846A Gigabit SX

(M2)

J4845A Gigabit LX

(M2)

J4847A 0-Port

(M2)

J4857A Mini-GBIC (M4)

J4885A EP

J4879A T-Flow

For M2, M4, and EP

Redundant Management

modules:

- H2R07803.bin

For T-Flow Redundant

Management modules:

- TSP07801d.bin

For M2, M4, and EP

Redundant Management

modules:

- M2B07605.bin or greater

For T-Flow Redundant

Management modules:

- M2B07605.bin (all MP

images)

- VSB07100.bin (VSM code)

— 10 Gigabit Ethernet (10GE)

Modules

Note: To upgrade FPGA

code, refer to “Upgrading

the FPGA on a 10 Gigabit

Ethernet Module” on

page 11.

The Field-Programmable

Gate Arrays (FPGAs) in 10

Gigabit Ethernet Modules

use the following software.

J4891A FPGA:

rxbmgr.bin – version 80,

revision 6

rxpp.bin – version 81,

revision 16

txaccum.bin – version 82,

revision 6

txpp.bin – version 83,

revision 13

ageram.bin – version 84,

revision 4

J8174A FPGA:

xpp.bin – version 88, revision

xtm.bin – version 89, revision

Note: To determine the

FPGA versions running on a

10GE module, enter show

flash. The version

information is listed

separately for each 10

Gigabit Ethernet module in

the chassis.

10 Gigabit Ethernet modules

do not use any of the boot

images listed above.

ProCurve 6308M-

—

HPR06636.bin

M1B07108.bin or greater

recommended

Release Notes for 07.8.04 Upgrading Software on an M2, M4, or EP Management Module to Release 07.8.04a

Upgrading Software on an M2, M4, or EP Management Module to

Release 07.8.04a

This section explains how to upgrade the software used on M2, M4, and EP redundant management modules on

a ProCurve 9304M, ProCurve 9308M, or ProCurve 9315M routing switch to release 07.8.04a.

NOTE: As shown in Table 5, newer software versions require newer versions of boot code. Software versions

use a five-digit number in the format: xx.x.xx; for example, 07.8.04a. Boot code versions use a six-digit number in

the format: xx.xx.xx; for example, 07.06.05.

Different procedures are used to upgrade an M2, M4, or EP management module, depending on the version of

software running on the module:

• A software release earlier than 07.6.01b

• Software release 07.6.01b or greater

NOTE: M1 Management modules (discontinued) do not support software releases 07.x.xx, and are, therefore,

not described in this section. The latest software release supported on an M1 management module is 06.6.36.

Restrictions

• Software release 07.8.04a requires boot code version 07.06.05 to support all hardware modules and

decompress new software images.

A new compression algorithm was introduced in software releases greater than 07.6.01b to generate

software images. The new compression algorithm allows a software image to contain more features.

Software release 07.6.01b was introduced as a special release that is used as an intermediate step when you

upgrade to a later software release. After you install release 07.6.01b and reboot a routing switch, the switch

is able to copy the latest software images to flash memory.

• On an M2, M4, or EP redundant management module, boot code is not automatically copied from the active

to the standby management module. (However, software code is automatically copied to a standby

management module.)

To copy boot code from the active to a standby management module, you must enter the sync boot

command.

• On a ProCurve 9315M, software release 07.5.04 is the earliest release supported. If a management module

is running software earlier than release 07.5.04, you cannot upgrade the module in a 9315M chassis. Instead,

you must upgrade it in a 9304M or 9308M chassis.

Upgrading to Software Release 07.8.04a: Overview

To upgrade an M2, M4, or EP management module to release 07.8.04a, you must follow these general steps:

A. Upgrade the boot code on the management module to version 07.06.05. If necessary, use the sync boot

command to copy boot code from the active to a standby management module in the routing switch. Then reboot

the routing switch to load boot code 07.06.05.

ProCurve 6208M-

—

HPS06636.bin

M1B07108.bin or greater

recommended

M1 management modules (without Redundant Management) have been discontinued.

Does not support Secure Shell (SSH) version 1.

Routing

Switch

Modules Software Image Minimum Boot Code

Required

Upgrading Software on an M2, M4, or EP Management Module to Release 07.8.04a Release Notes for 07.8.04

B. If the routing switch is running software EARLIER than release 07.6.01b, copy release 07.6.01b to flash

memory. Then reboot the device to load the 07.6.01b software.

C. Copy release 07.8.04a to flash memory, and reboot the routing switch to load 07.8.04a software.

A. Upgrading Boot Code on a Management Module to Version 07.06.05

To upgrade the boot code on an M2, M4, or EP management module to version 07.06.05:

1. Store boot code version 07.06.05 (filename: M2B07605.bin) on a TFTP server that the routing switch can

access.

2. Enter the following command at the privileged EXEC level of the CLI (for example: ProCurve 9300#) to copy

the boot code from the TFTP server into the flash memory of the management module:

copy tftp flash <ip-addr> <image-file-name> boot

3. Verify that the code has been successfully copied by entering the following command at any level of the CLI:

show flash

The boot code version is displayed on the line that begins with “Boot Image size”. Ensure that boot code

version 07.06.05 is displayed for the active management module.

4. If a standby (redundant) management module is installed in the routing switch, synchronize the boot code on

the standby management module by entering the sync boot command.

Verify that boot code 07.06.05 has been successfully copied on the standby management module by entering

the show flash command.

5. Reboot the routing switch to load boot code 07.06.05.

B. Upgrading Software on a Management Module From a Release Earlier than

07.6.01b

To upgrade the software on an M2, M4, or EP management module from a release EARLIER than 07.6.01b to

release 07.8.04a:

1. Verify the version of boot code installed on the management module by entering the show flash command.

The boot code version is displayed at the end of the line that begins with “Boot Image size”. Ensure that boot

code version 07.06.05 is displayed.

NOTE: The show flash command only displays the version of boot code installed on the device. It does not

display the version of boot code running on the device.

If you rebooted the routing switch after installing boot code 07.06.05 (as described in “A. Upgrading Boot

Code on a Management Module to Version 07.06.05”), the required boot code is running. If you are not sure,

ProCurve recommends that you reboot the device now.

2. Store software release 07.6.01b (filename: H2R07601b.bin) on a TFTP server that the routing switch can

access.

3. Upgrade the software on the management module to version 07.6.01b by entering the following command:

copy tftp flash <ip-address> H2R07601b.bin [primary | secondary]

Where:

primary copies software to the primary (default) storage area in flash memory.

secondary copies software to the secondary area in flash memory.

If no redundant management module is installed, the message TFTP to Flash Done is displayed when the

upgrade is complete.

If a redundant management module is installed, the message Sync Secondary code in flash...Done

Release Notes for 07.8.04 Upgrading Software on an M2, M4, or EP Management Module to Release 07.8.04a

is displayed when the flash images are synchronized and the upgrade is complete.

4. Verify that the software has been successfully copied by entering the show flash command at any level of the

CLI:

• The software release in the primary flash is displayed at the end of the line that begins with “Compressed

Pri Code Size”.

• The software release in the secondary flash is displayed at the end of the line that begins with

“Compressed Sec Code Size”.

Ensure that software release 07.6.01b is stored in the primary or secondary flash area.

5. Reboot the routing switch to load software release 07.6.01b from the area of flash memory (primary or

secondary) where you stored it.

6. Continue with “C. Upgrading Software on a Management Module From Release 07.6.01b or Greater” to

upgrade the software to release 07.8.04a.

C. Upgrading Software on a Management Module From Release 07.6.01b or

Greater

To upgrade the software on an M2, M4, or EP management module from release 07.6.01b or greater to release

07.8.04a:

1. Verify the version of boot code running on the management module by entering the show flash command.

The boot code version is displayed at the end of the line that begins with “Boot Image size”. Ensure that boot

code version 07.06.05 is displayed.

NOTE: The show flash command only displays the version of boot code installed on the device. It does not

display the version of boot code running on the device.

If you rebooted the routing switch after installing boot code 07.06.05 (as described in “A. Upgrading Boot

Code on a Management Module to Version 07.06.05”), the required boot code is running. If you are not sure,

ProCurve recommends that you reboot the device now.

2. Store software release 07.8.04a (filename: H2R07801d.bin) on a TFTP server that the routing switch can

access.

3. Upgrade the software on the management module to version 07.8.04a by entering the following command:

copy tftp flash <ip-address> H2R07801d.bin [primary | secondary]

Where:

primary copies software to the primary (default) storage area in flash memory.

secondary copies software to the secondary storage area.

If no redundant management module is installed, the message TFTP to Flash Done is displayed when the

upgrade is complete.

If a redundant management module is installed, the message Sync Secondary code in flash...Done

is displayed when the flash images are synchronized and the upgrade is complete.

4. Verify that the software has been successfully copied by entering the show flash command at any level of the

CLI:

• The software release in the primary flash is displayed at the end of the line that begins with “Compressed

Pri Code Size”.

• The software release in the secondary flash is displayed at the end of the line that begins with

“Compressed Sec Code Size”.

Ensure that software release 07.8.04a is stored in the primary or secondary flash area.

Using SNMP to Upgrade Software on a Management Module Release Notes for 07.8.04

5. Reboot the routing switch to load software release 07.8.04a from the area of flash memory (primary or

secondary) where you stored it.

NOTE: When you reload the software after upgrading the software to release 07.8.04a, the routing switch

displays a message to say that the configuration has changed and prompts you to save the changes. This

message is displayed even if you do not make any configuration changes because the software records its

release number in the running-config file when the software is loaded onto the switch. Enter Y to reload

without saving the change or save the change and reload.

Using SNMP to Upgrade Software on a Management Module

Third-party SNMP management applications such as HP OpenView can upgrade software on a routing switch.

NOTE: In software releases earlier than 07.5.04, the SNMP agent does not check for type validity with the

SNMP version. In software release 07.5.04 and greater, the SNMP agent does not send a reply for a varbind, if the

type of the varbind is not a known type for that version of SNMP. For example, MIB objects of type Counter64

cannot be retrieved using a v1 packet, as Counter64 is a v2c and v3 type.

Make sure you use the correct procedure for your device and processor type. For example, do not use the

Management Processor procedure to upgrade the switching processors on a T-Flow module.

The syntax shown in this section assumes that you have installed HP OpenView in the “/usr” directory.

ProCurve recommends that you make a backup copy of the startup-config file before you upgrade the software. If

you need to run an older release, you will need to use the backup copy of the startup-config file.

Upgrading a Management Processor using SNMP

Use the following procedure to upgrade:

• An M2, M4, or EP module

• Management processor on the T-Flow module

To upgrade software code on the Management Processor:

1. Configure a read-write community string on the ProCurve device, if one is not already configured. To

configure a read-write community string, enter the following command from the global CONFIG level of the

CLI:

snmp-server community <string> rw

where <string> is the community string and can be up to 32 characters long.

2. On the ProCurve device, enter the following command from the global CONFIG level of the CLI:

no snmp-server pw-check

This command disables password checking for SNMP set requests. If a third-party SNMP management

application does not add a password to the password field when it sends SNMP set requests to an ProCurve

device, by default the ProCurve device rejects the request.

3. From the command prompt in the UNIX shell, enter the following command:

/usr/OV/bin/snmpset -c <rw-community-string> <hp-ip-addr> 1.3.6.1.4.1.1991.1.1.2.1.5.0

ipaddress <tftp-ip-addr> 1.3.6.1.4.1.1991.1.1.2.1.6.0 octetstringascii <file-name>

1.3.6.1.4.1.1991.1.1.2.1.7.0 integer <command-integer>

Where:

<rw-community-string> is a read-write community string configured on the ProCurve device.

<hp-ip-addr> is the ProCurve device’s IP address.

Release Notes for 07.8.04 Upgrading the FPGA on a 10 Gigabit Ethernet Module

<tftp-ip-addr> is the TFTP server’s IP address.

<file-name> is the image file name.

<command-integer> is one of the following values:

20 – Downloads the software code into the device’s primary flash area.

22 – Downloads the software code into the device’s secondary flash area.

Upgrading the FPGA on a 10 Gigabit Ethernet Module

This section explains how to upgrade an FPGA (Field-Programmable Gate Array) on a 10 Gigabit Ethernet

module. 10 Gigabit Ethernet modules do not have boot code separate from the management module. However,

they do have FPGAs that require separate software.

NOTE: The J8174A 2-port 10 Gigabit Ethernet module with XENPAK optics uses a different FPGA file than the

older J4891A 1-port 10 Gigabit Ethernet module. See Table 5 on page 6 for a list of the FPGA files supported on

both the 1-port and 2-port 10 Gigabit Ethernet modules.

The J8174A 2-port 10 Gigabit Ethernet module with XENPAK optics can function in the same chassis with the

older J4891A 1-port 10 Gigabit Ethernet module.

If an upgrade is required for any of the FPGA files, you must upgrade all the FPGA files.

To upgrade the FPGA on a 10 Gigabit Ethernet module:

1. Complete the upgrades of the boot code and software code, if required.

2. Enter the following command for the 10 Gigabit Ethernet module at the privileged EXEC level of the CLI:

10gig copy tftp flash <ip-addr> <filename> [module <slotnum>]

Where:

tftp specifies the location of the FPGA file. The tftp parameter shows that the file is on a TFTP server.

<ip-addr> specifies the IP address of the TFTP server, if you specify tftp.

<filename> specifies the FPGA file name. The 2-port 10 Gigabit Ethernet module has only two FPGA files;

xpp.bin and xtm.bin. For more information on the supported FPGA files, see Table 5 on page 6.

module <slotnum> is an optional parameter that specifies the modules on which you want to install the

upgrade. If you do not specify a slot number, the command upgrades the FPGA on all 10 Gigabit Ethernet

modules in the chassis.

Example

ProCurve 9300# 10gig copy tftp flash 10.10.10.10 rxbmgr.bin

ProCurve 9300# 10gig copy tftp flash 10.10.10.10 rxpp.bin

ProCurve 9300# 10gig copy tftp flash 10.10.10.10 txaccum.bin

ProCurve 9300# 10gig copy tftp flash 10.10.10.10 txpp.bin

ProCurve 9300# 10gig copy tftp flash 10.10.10.10 ageram.bin

NOTE: You can store and copy the FPGA files using any valid filename. You are not required to store and

copy the files using the names listed in “Boot Code Requirements for ProCurve Software” on page 5. The

device uses information within the files to install them in the correct FPGAs, and the show flash command

lists the FPGAs according to the names in “Boot Code Requirements for ProCurve Software” on page 5.

3. Reload the software by entering one of the following commands:

• reload (this command boots from the default boot source, which is the primary flash area by default)

• boot system flash primary | secondary

Using Different Combinations of Management Modules Release Notes for 07.8.04

NOTE: The show flash command will list the new FPGA code versions but the new versions do not take

effect until you reload the software.

Using Different Combinations of Management Modules

This section describes the different combinations of M1, M2, M4, EP, and T-Flow management modules supported

on ProCurve 9304M, ProCurve 9308M, and ProCurve 9315M routing switches.

NOTE: The following types of management modules are mutually exclusive:

- M1 management modules

- M2 or M4 redundant management modules

- EP redundant management modules

- T-Flow redundant management modules

A ProCurve routing switch does not operate if two redundant management modules of different types are installed.

Also, M1 management modules do not operate in a ProCurve 9315M routing switch.

Redundant management means that a device can operate with two management modules installed; one active

(primary) and one standby (secondary). If the active management module becomes unavailable, the standby

management module automatically takes over system operation.

Management modules with redundant management capabilities include the following M2, M4, EP, and T-Flow

modules:

• J4885A ProCurve 9300 EP Mini-GBIC Redundant Management Module (8-port)

• J4879A ProCurve 9300 T-Flow Redundant Management Module (0-port — discontinued)

• J4857A ProCurve 9300 Mini-GBIC Redundant Management Module (8-port, M4 — discontinued)

• J4845A ProCurve 9300 GigLX Redundant Management Module (8-port, M2 — discontinued)

• J4846A ProCurve 9300 GigSX Redundant Management Module (8-port, M2 — discontinued)

• J4847A ProCurve 9300 Redundant Management Module (0-port, M2 — discontinued)

If you are using a Redundant Management module, you can install either one or two such modules in the routing

switch, as shown in Table 6. For more information, see “Using Redundant Management Modules” in the

Installation and Basic Configuration Guide included on the Documentation CD-ROM shipped with your

Table 6: Supported Management Module Combinations

Primary Management Module Secondary Management

Module

Notes

J4885A EP Mini-GBIC Redundant

Management Module

Another EP Redundant

Management Module

—

Any M2 or M4 Redundant

Management Module (Discontinued)

Another M2 or M4

Redundant Management

Module

When you use an M2 and M4 in the same

switch, ProCurve recommends using the

faster M4 as the primary redundant

management module. If the M4 fails, the

system will use the slower M2 module.

J4879A T-Flow Redundant

Management Module (Discontinued)

Another J4879A T-Flow

Redundant Management

Module

—

Any M1 Management Module

(Discontinued)

N/A Supported only in the ProCurve 9304M

and ProCurve 9308M routing switches. No

redundant management options.

Release Notes for 07.8.04 Non-Redundant Management on ProCurve 9304M and ProCurve 9308M Routing Switches

management module, and also downloadable from the ProCurve website (see “To Download Product

Documentation:” on page 3).

Non-Redundant Management on ProCurve 9304M and ProCurve

9308M Routing Switches

Management modules without Redundant Management are sometimes termed “M1” modules (for “Management

1”). These modules, now discontinued, operate only in the ProCurve 9304M and ProCurve 9308M routing

switches. M1 modules include:

• J4141A ProCurve 9300 10/100 Management Module (16-port — discontinued)

• J4144A ProCurve 9300 Gigabit SX Management Module (8-port — discontinued)

• J4146A ProCurve 9300 Gigabit 4LX/4SX Management Module (8-port — discontinued)

NOTE: M1 management modules do not operate in the ProCurve 9315M routing switch. Also, if you are using an

M1 management module in a ProCurve 9304M or ProCurve 9308M, no other management module (non-

redundant or redundant) can be installed in the routing switch.

Maximum Size of Startup-Config and Running-Config Files

Each ProCurve device has a maximum supported size for the running-config and the startup-config file. If you use

TFTP to load additional information into a device’s running-config or startup-config file, it is possible to exceed the

maximum supported size. If this occurs, you will not be able to save the configuration changes.

Table 7 lists the maximum size of the running-config and the startup-config files on ProCurve devices.

NOTE: The maximum supported file size of each file is not the combined size of the running-config and startup-

config files. The running-config and startup-config files can each be the size listed in Table 7.

To determine the size of an ProCurve device’s running-config or startup-config file, copy the file to a TFTP server.

Then use the directory services on the server to list the size of the copied file. To copy the running-config or

startup-config file to a TFTP server, use one of the following commands.

• To copy the running-config to a TFTP server:

copy running-config tftp <ip-addr> <filename>

• To copy the startup-config file to a TFTP server:

copy startup-config tftp <ip-addr> <filename>

Table 7: Maximum Sizes Supported for running-config and the startup-config Files

Device Maximum Size of running-config

and startup-config files

ProCurve 9315 using Management II or

higher

256 kilobytes (KB)

ProCurve 9304M or ProCurve 9308M

using Management II or higher

256 KB

ProCurve 9304M or ProCurve 9308M

using Management I (discontinued)

128 KB

ProCurve 6308M-SX or ProCurve

6208M-SX (discontinued)

64 KB

Removing a Module from an Active Device Release Notes for 07.8.04

Removing a Module from an Active Device

Before you remove a module from a routing switch in operation, first disable the module. Disabling the module

before removing it prevents a brief service interruption on other unmanaged modules. The brief interruption can be

caused by the device re-initializing other modules when you remove an enabled module.

NOTE: This section does not apply to the active or standby Redundant Management modules. The disable

module and enable module commands are not supported on management modules.

To disable a module, enter the following command at the Privileged EXEC level of the CLI:

disable module <slot-num>

Where <slot-num> specifies the slot number as follows:

• Slots in a 4-slot chassis are numbered 1 – 4, from top to bottom.

• Slots in an 8-slot chassis are numbered 1 – 8, from left to right.

• Slots in a 15-slot chassis are numbered 1 – 15, from left to right.

Example

ProCurve 9300# disable module 3

This command disables the module in slot 3.

NOTE: If you remove the module without first disabling it, the routing switch re-initializes the other modules in the

device, causing a brief interruption in service after which the device resumes normal operation.

You do not have to enable a module after inserting it in the chassis. The module is automatically enabled when

you insert the module into a running device or when you power on the device.

To replace a removed module with a different type of module, you must configure the slot for the new module. To

configure a slot for a module, use the module command at the global CONFIG level of the CLI.

After disabling a module, if you decide not to remove the module, re-enable the module using the following

command:

enable module <slot-num>

Example

The following command re-enables the module in slot 3:

ProCurve 9300# enable module 3

Configuring the ProCurve 9315M

When configuring a ProCurve 9315M 15-slot routing switch, take into account the guidelines and restrictions in

this section.

Minimum Software Release Supported

The ProCurve 9315M requires software release 07.5.04 or greater.

NOTE: On a ProCurve 9315M, software release 07.5.04 is the earliest release supported. If a management

module is running software earlier than release 07.5.04, you cannot upgrade the module in a 9315M chassis.

Instead, you must upgrade it in a 9304M or 9308M chassis. For more information, see “Upgrading Software on an

M2, M4, or EP Management Module to Release 07.8.04a” on page 7.

Release Notes for 07.8.04 Enhancements and Configuration Notes in 07.8.03

Inserting or Removing an EP Module on a ProCurve 9315M

NOTE: This section applies only to a ProCurve 9315M (15-slot chassis) with EP modules.

Do not insert or remove EP modules in a ProCurve 9315M until the device has fully booted. Generally, booting

takes around two minutes. You can determine whether the device has fully booted by looking at the management

console. Once the device boots, a command prompt or login prompt is displayed.

After the device has booted, allow time for the device to fully complete the removal or insertion before removing or

inserting another module. Generally, this takes about 30 seconds. After you remove or insert a module, the CLI

displays a message confirming completion of the change. Wait for this message before removing or inserting

another module.

Slot Locations for Redundant Management Modules

The 15 slots in the ProCurve 9315M are divided among 4 internal regions. Slots 1 – 4 belong to the same region;

slots 5 – 8 belong to the same region; slots 9 – 12 belong to the same region, and slots 13 – 15 belong to the

same region. If you are using redundant management modules, ProCurve recommends that you place both

management modules in slots belonging to the same region. For example, if you place one management module

in slot 5, ProCurve recommends that you place the other management module in slot 6, 7, or 8.

MAC Addresses

The ProCurve 9315M makes use of locally administered MAC addresses. If your site already uses locally

administered MAC addresses of the vendor OUI, which is 00e052, there could be a MAC address conflict with one

of the ports on the ProCurve device.

Server Trunk Groups

If you plan to configure ports on a module into a server trunk group, use the following guideline:

• For a multi-slot trunk group (one configured on two forwarding modules), the modules must both be in the

same set of slots (slots 1 – 7 or 9 – 15).

You do not need to follow this guideline for a switch trunk group.

NOTE: In software releases earlier than 07.6.00, the management module(s) and the module that had the server

trunk group’s ports were required to be in the same set of slots (slots 1 – 7 or 9 – 15). In software release 07.6.00

and later, there is no longer a restriction on the location of the management module relative to the module used for

server trunking. However, it is still a requirement that the module that has the server trunk group’s lead ports

cannot reside in slot 8.

VLANs

In release 07.6.01b, you could configure only up to 2195 Layer 2 VLANs on the ProCurve 9315M routing switch.

The system-max vlan <num> command allowed you to allocate a higher number of VLANs, but the software

allowed you to actually create only 2195 of the allocated VLANs.

Starting with release 07.6.04, this restriction has been removed. You can create the full number of allocated Layer

2 VLANs on the 15-slot ProCurve 9315M routing switch, up to 4095.

Enhancements and Configuration Notes in 07.8.03

On ProCurve 9300M Series routing switches, no new software enhancements are supported in software release

07.8.03.

Software Fixes Release Notes for 07.8.04

Software Fixes

The fixes for software bugs found on ProCurve 9300M Series routing switches in software releases 07.8.00h

through 07.8.03 are described in the following table. Software fixes are listed by bug ID for the software release in

which they were implemented.

Bug ID Bug Description Protocol/

Feature

Version

Found

Version

Fixed

07.8.00h

25991 In the display of InUcastPkts and OutUcastPkt 64-

bit packet counters, the packet counts wrap after 32

bits.

Other 07.8.00

31045 The default route learned through OSPF is not

displayed in the routing table if you enter the clear

ip route 0.0.0.0/0.0.0.0 command.

OSPF 07.8.00

32896 802.1w packets are not forwarded by the routing

switch.

Spanning Tree 07.8.00

35710 If you enter the no web management command,

access on port 80 is disabled while access on port

280 is allowed.

Web

Management

07.8.00

35727 During a system reload, the following error

message is displayed even when the number of

Spanning Tree Protocol (STP) instances is reduced

by using topology groups:

Error - failed to bind STP to vlan xxx

Spanning Tree 07.8.00

3676 After you modify an access control list (ACL),

protection against a reload is performed.

ACL 07.8.00

40829 A Border Gateway Protocol (BGP) reload is

performed when the preceding NLRI entry is NULL.

BGP 07.8.00

41630 When private VLANs are configured, if you remove

the lowest numbered port mapping in the primary

VLAN, higher port mappings are disabled.

VLAN 07.8.00

44374 An error message is displayed when you configure

multiple IP address on a group router interface.

Other 07.8.00

44949 ARP learning is performed much slower when

Layer 3 bidirectional traffic is transmitted at a 100M

rate.

Other 07.8.00

45104 A watchdog reset is caused when BGP passes out

of the Direct Memory Access (DMA) range.

BGP 07.8.00

45198 Port 280 remains up if you enter the no web-

management http command followed by the no

web-management hp-top-tools command.

Web

Management

07.8.00

45277 A system reload is performed following a link-list

subroutine error.

Other 07.8.00

Release Notes for 07.8.04 Software Fixes

45318 After you disable and swap a module, the active

management module crashes.

System 07.8.00

45319 When you enter the ip rebind-acl all command, the

following message is logged:

Exceed max DMA 9 L4 cam resource,

using flow based ACL instead

ACL 07.8.00

45415 SSH may reload if a different client public-key is

received for authentication.

SSH 07.8.00

45550 A 10 Gigabit Ethernet port is not displayed in show

fdp interface command output.

CLI 07.8.00

46777 The globally configured value for the sFlow

sampling rate is not applied to the secondary trunk

links when you enter the config-trunk-ind

command in the startup configuration.

sFlow 07.8.00

46924 The sflow sample command entered at the trunk

level is not supported on a routing switch during a

reload.

sFlow 07.8.00

47464 A variable is not initialized to zero. As a result, a

large data chunk may be allocated, causing a

system reload.

System 07.8.00

47599 If route-only mode is configured, forwarding stops

when you exit from monitor mode.

System 07.8.00

47855 The OSPF timer displays the following message:

Warning Checksum bad in Link State

Database error.

OSPF 07.8.00

48115 The debug ip igmp physical_port command is not

performed on ports 32 to 48 on an EP 48-Port 10/

1000-TX RJ45 module.

IGMP 07.8.00

48132 When a trunk server is used, the first packet in a

flow is sent twice.

System 07.8.00

48313 A Protocol Independent Multicast (PIM) reload is

performed after detecting a virtual port (instead of a

physical port) configured in the forwarding OIF.

PIM 07.8.00

48383 ACL-denied packets are not copied to a redirected

interface.

ACL 07.8.00

48442 The BGP route dampening feature does not always

dampen flapping routes after four flaps. Some

routes are still dampened after two flaps.

BGP 07.8.00

48721 The routing switch reloads if an SSH client starts a

session when SSH debugging is enabled.

SSH 07.8.00

48823 If you configure multiple addresses on an interface

and reload the switch, RIPv2 advertises from only

the lowest IP address.

RIPv2 07.8.00

Bug ID Bug Description Protocol/

Feature

Version

Found

Version

Fixed

Page is loading ...

HP 9315M User manual

Brand: HP

Model: 9315M

Category: Network switch modules

Type: User manual

This manual is also suitable for

ProCurve 9315M

Download PDF

report

HP 9315M User manual

This manual is also suitable for

HP 9315M User manual

Related papers

Other documents