Marantz PMD910 User manual

Brand: Marantz

Model: PMD910

Category: DVD players

Type: User manual

DVD Player

Model PMD910 User Guide

CLASS 1 LASER PRODUCT

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

ENGLISH

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION:

POUR ÉVITER LES CHOC ÉLECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE ET POUSSER

JUSQU’AU FOND.

NOTE TO CATV SYSTEM INSTALLER:

This reminder is provided to call the CATV (Cable-TV) system installer’s attention to Section 820-40 of the NEC which provides

guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the

building, as close to the point of cable entry as practical.

NOTE:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions,

may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television

reception, which can be determined by tuning the

equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for

help.

NOTE:

Changes or modifications not expressly approved by the

party responsible for compliance could void the user’s

authority to operate the equipment.

ENGLISH

IMPORTANT SAFETY

INSTRUCTIONS

READ BEFORE OPERATING EQUIPMENT

This product was designed and manufactured to meet strict quality and

safety standards. There are, however, some installation and operation

precautions which you should be particularly aware of.

1. Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2. Retain Instructions – The safety and operating instructions should

be retained for future reference.

3. Heed Warnings – All warnings on the product and in the operating

instructions should be adhered to.

4. Follow Instructions – All operating and use instructions should be

followed.

5. Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners. Use a

damp cloth for cleaning.

6. Attachments – Do not use attachments not recommended by the

product manufacturer as they may cause hazards.

7. Water and Moisture – Do not u se this product near water-for

example, near a bath tub, wash bowl, kitchen sink, or laundry tub,

in a wet basement, or near a swimming pool, and the like.

8. Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall, causing

serious injury to a child or adult, and serious damage to the

product. Use only with a cart, stand, tripod, bracket, or table

recommended by the manufacturer, or sold with the product. Any

mounting of the product should follow the manufacturer’s

instructions, and should use a mounting accessory recommended

by the manufacturer.

9. CART – A product and cart combination should be moved with

care. Quick stops, excessive force, and uneven surfaces may

cause the product and cart combination to overturn.

10. Ventilation – Slots and openings in the cabinet are provided for

ventilation and to ensure reliable operation of the product and to

protect it from overheating, and these openings must not be

blocked or covered. The openings should never be blocked by

placing the product on a bed, sofa, rug, or other similar surface.

This product should not be placed in a built-in installation such as

a bookcase or rack unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

11. Power Sources – This product should be operated only from the

type of power source indicated on the marking label. If you are not

sure of the type of power supply to your home, consult your

product dealer or local power company. For products intended to

operate from battery power, or other sources, refer to the

operating instructions.

12. Grounding or Polarization – This product may be equipped with a

polarized alternating-current line plug (a plug having one blade

wider than the other). This plug will fit into the power outlet only

one way. This is a safety feature. If you are unable to insert the

plug fully into the outlet, try reversing the plug. If the plug should

still fail to fit, contact your electrician to replace your obsolete

outlet. Do not defeat the safety purpose of the polarized plug.

AC POLARIZED PLUG

13. Power-Cord Protection – Power-supply cords should be routed so

that they are not likely to be walked on or pinched by items placed

upon or against them, paying particular attention to cords at plugs,

convenience receptacles, and the point where they exit from the

product.

14. Protective Attachment Plug – The product is equipped with an

attachment plug having overload protection. This is a safety

feature. See Instruction Manual for replacement or resetting of

protective device. If replacement of the plug is required, be sure

the service technician has used a replacement plug specified by

the manufacturer that has the same overload protection as the

original plug.

15. Outdoor Antenna Grounding – If an outside antenna or cable

system is connected to the product, be sure the antenna or cable

system is grounded so as to provide some protection against

voltage surges and built-up static charges. Article 810 of the

National Electrical Code, ANSI/NFPA 70, provides information

with regard to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna discharge

unit, size of grounding conductors, location of antenna-discharge

unit, connection to grounding electrodes, and requirements for the

grounding electrode. See Figure 1.

16. Lightning – For added protection for this product during a lightning

storm, or when it is left unattended and unused for long periods of

time, unplug it from the wall outlet and disconnect the antenna or

cable system. This will prevent damage to the product due to

lightning and power-line surges.

17. Power Lines – An outside antenna system should not be located

in the vicinity of overhead power lines or other electric light or

power circuits, or where it can fall into such power lines or circuits.

When installing an outside antenna system, extreme care should

be taken to keep from touching such power lines or circuits as

contact with them might be fatal.

18. Overloading – Do not overload wall outlets, extension cords, or

integral convenience receptacles as this can result in a risk of fire

or electric shock.

19. Object and Liquid Entry – Never push objects of any kind into this

product through openings as they may touch dangerous voltage

points or short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

ENGLISH

iii

20. Servicing – Do not attempt to service this product yourself as

opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified service

personnel.

21. Damage Requiring Service – Unplug this product from the wall

outlet and refer servicing to qualified service personnel under the

following conditions:

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the

operating instructions as an improper adjustment of other controls

may result in damage and will often require extensive work by a

qualified technician to restore the product to its normal operation.

e. If the product has been dropped or damaged in any way, and

f. When the product exhibits a distinct change in performance – this

indicates a need for service.

22. Replacement Parts – When replacement parts are required, be

sure the service technician has used replacement parts specified

by the manufacturer or have the same characteristics as the

original part. Unauthorized substitutions may result in fire, electric

shock, or other hazards.

23. Safety Check – Upon completion of any service or repairs to this

product, ask the service technician to perform safety checks to

determine that the product is in proper operating condition.

24. Wall or Ceiling Mounting – The product should be mounted to a

wall or ceiling only as recommended by the manufacturer.

25. Heat – The product should be situated away from heat sources

such as radiators, heat registers, stoves, or other products

(including amplifiers) that produce heat.

FIGURE 1

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la Classe B est conforme à la norme

NMB-003 du Canada.

GROUND

CLAMP

NEC - NATIONAL ELECTRICAL CODE

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

ELECTRIC

SERVICE

EQUIPMENT

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

ENGLISH

This product incorporates copyright protection technology that is

protected by method claims of certain U. S. patents and other intellectual

property rights owned by Macrovision Corporation and other rights

owners. Use of this copyright protection technology must be Authorized

by Macrovision Corporation, and is intended for home and other limited

viewing uses only unless otherwise authorized by Macrovision

corporation. Reverse engineering or disassembly is prohibited.

Manufactured under license from Dolby Laboratories. "Dolby" and

the double-D symbol are trademarks of Dolby Laboratories.

DTS" and "DTS Digital" are trademarks of Digital Theater Systems,Inc.

LASER SAFETY

This unit employs a laser. Only a qualified service

person should remove the cover or attempt to service

this device, due to possible eye injury.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN

OPEN AVOID EXPOSURE TO BEAM (WARNING

LOCATION: INSIDE ON LASER COVERSHIELD)

Operating Environment

Operating environment temperature and humidity:

+5°C to +35°C (+41°F to +95°F); less than 85%RH (cooling vents not

blocked)

Do not install in the following locations

• Location exposed to direct sunlight or strong artificial light

• Location exposed to high humidity, or poorly ventilated location

This product is for general household purposes. Any failure due to

use for other than household purposes (such as long - term use for

business purposes in a restaurant or use in a car or ship) and which

requires repair will be changed for even during the warranty period.

ENGLISH

BEFORE YOU START ..................................3

What’s in the box ....................................................................................... 3

Putting the batteries in the remote control ................................................. 3

Using the remote control ............................................................................ 3

Discs compatible with this player ............................................................... 4

DVD Video regions .................................................................................... 4

MP3 compatibility information .................................................................... 4

Caution! ...................................................................................................... 4

BASIC CONNECTION .................................. 5

S -Video Out Connection ........................................................................... 5

Composite video out Connection ............................................................... 6

Component video out connection (480i/480p) ........................................... 6

Analog Audio Connection ........................................................................... 7

Digital Audio Connection ............................................................................ 8

System Control Connection ....................................................................... 9

CONTROLS & DISPLAY ............................10

Front Panel .............................................................................................. 10

Display ...................................................................................................... 11

Rear Panel ............................................................................................... 12

Remote Controller Unit ............................................................................ 13

BASIC FUNCTION .....................................16

Open / Close Disc Tray ............................................................................ 16

Basic play of DVD, VIDEO-CD or CDDA ................................................. 17

Basic play of MP3 .................................................................................... 18

Selecting VIDEO MODE .......................................................................... 18

Selecting MENU ITEMS (DVD or Video CD with PBC only) .................... 19

STOP and POWER OFF .......................................................................... 19

SEARCH .................................................................................................. 20

SKIP ......................................................................................................... 21

SLOW ...................................................................................................... 21

Selecting Audio Languages (DVD only) ................................................... 22

Selecting Subtitles (DVD only) ................................................................. 23

Selecting Angles (DVD only) .................................................................... 23

Kodak picture CD play ............................................................................. 24

JPEG file play .......................................................................................... 24

TABLE OF CONTENTS

ADVANCED FUNCTION ............................25

3D sound effect (MP3, CDDA , Dolby Digital 2CH Stereo) ...................... 25

Utilizing Repeat Function ......................................................................... 26

SHUFFLE (VCD with PBC off, MP3, CDDA only) .................................... 27

PROGRAM (VCD, MP3, CDDA only) ...................................................... 27

Digest (VCD,JPEG,Kodak picture CD, CDDA only) ................................. 28

MARKER (DVD, VCD WITH PBC OFF, CDDA)....................................... 29

Display ..................................................................................................... 29

Zoom screen ............................................................................................ 31

CUSTOMIZING DVD PERFORMANCE ..... 32

Audio ........................................................................................................ 32

Video ........................................................................................................ 33

Other ........................................................................................................ 35

Languages (DVD only) ............................................................................. 35

Parental Lock (DVD only) ........................................................................ 36

ADDITIONAL INFORMATION .................... 37

Handling discs .......................................................................................... 37

Cleaning the pickup lens .......................................................................... 37

Problems with condensation .................................................................... 37

Hints on installation .................................................................................. 38

Moving the player ..................................................................................... 38

Power cord caution .................................................................................. 38

Resetting the player ................................................................................. 38

Malfunctioning of this unit ........................................................................ 38

Glossary ................................................................................................... 39

TROUBLESHOOTING................................40

SPECIFICATIONS ...................................... 42

CONGRATULATIONS ON YOUR PURCHASE OF THIS FINE MARANTZ PRODUCT.

MARANTZ is on the leading edge of DVD research for consumer products and this unit incorporates the latest technological developments.

We are sure you will be fully satisfied with the DVD player.

Thank you for your support.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the

instructions, put them away in a safe place for future reference.

• This player is not suitable for commercial use.

ENGLISH

What’s in the box

Thank you for buying this MARANTZ product. Please confirm

that the following accessories are in the box when you open it.

• Remote control

• AAA/R03 dry cell batteries x2

• Audio/Video cable

• System control cable

• Operating instruction (this manual)

• Warranty card

Putting the batteries in the remote control

1 Open the battery compartment cover on the back of the remote

control.

2 Insert two AAA/R03 batteries into the battery compartment

following the indications (+, -) inside the compartment.

3 Close the cover.

Note

Incorrect use of batteries can result in hazards such as leakage and

bursting. Please observe the following:

• Don’t mix new and old batteries together.

• Don’t use different kinds of battery together—although they may

look similar, different batteries may have different voltages.

• Make sure that the plus and minus ends of each battery match

the indications in the battery compartment.

• Remove batteries from equipment that isn’t going to be used for

a month or more.

When disposing of used batteries, please comply with governmental

regulations or environmental public instruction’s rules that apply in

your country or area.

BEFORE YOU START

Using the remote control

Keep in mind the following when using the remote control:

• Make sure that there are no obstacles between the remote and

the remote sensor on the unit.

• Use within the operating range and angle, as shown.

• Remote operation may become unreliable if strong sunlight or

fluorescent light is shining on the unit’s remote sensor.

• Remote controllers for different devices can interfere with each

other. Avoid using remotes for other equipment located close to

this unit.

• Replace the batteries when you notice a fall off in the operating

range of the remote.

Note

When using this player independently, set a REMOTE CONTROL

switch on the rear panel to INTERNAL. (page 9)

5m(17 feet)

ENGLISH

Discs compatible with this player

Any disc that displays one of the following logos should play in

this player. Other formats, including DVD-RAM, DVD-ROM,

CD-ROM (except those that contain MP3 files), and Photo CD

will not play.

DVD Video compatibility:

• Logos:

• Single-sided or double-sided discs

• Single layer or dual layer discs

• Dolby Digital, DTS (Digital out only), MPEG or Linear PCM

digital audio

• MPEG-2 digital video

Discs are generally divided into one or more titles. Titles may be

further subdivided into chapters.

DVD-R compatibility:

This unit can play DVD-R discs. Please note the following points when

using these discs:

• Logo:

• This unit can play DVD-R discs recorded as DVD video format.

Audio CD compatibility:

• Logos:

• 12cm or 8cm discs

• Linear PCM digital audio

• CD-Audio, CD-R* and CD-RW* formats

CDs are divided into tracks.

*This unit can play CD-R and CD-RW discs recorded in CD Audio or

Video CD format, or with MP3 audio files, or Kodak picture CD files.

Video CD compatibility:

• Logo:

• 12cm or 8cm discs

• MPEG-1 digital audio

• MPEG-1 digital video

Video CDs are divided into tracks.

Super VCD compatibility:

• Logo:

• 12cm (5in.) or 8cm (3in.) discs

• MPEG-1 digital audio

• MPEG-2 digital video

Super VCDs are divided into tracks.

DVD Video regions

All DVD Video discs carry a region mark on the case

somewhere that indicates which region(s) of the world the disc

is compatible with. Your DVD player also has a region mark,

which you can find on the rear panel. Discs from incompatible

regions will not play in this player. Discs marked ALL will play

in any player.

MP3 compatibility information

• The CD-ROM must be ISO 9660 compatible.

• Mono or stereo MPEG-1 Audio Layer 3 format, 32 or 44.1 or

48kHz, fixed bit-rate. Incompatible files will not play.

• Not compatible with variable bit-rate (VBR) files.

• This player only plays tracks that are named with the file

extension “.mp3” or “.MP3”.

• This player is compatible with multi-session discs.

• Use CD-R or CD-RW media for recording your MP3 files. The

disc must be finalized in order to play.

• Audio encoded at 128Kbps should sound close to regular audio

CD quality. Although this player will play 56 to 256k bit-rate MP3

tracks, the sound quality becomes noticeably worse at lower bit-

rates.

• This player can recognize a maximum of 126 folders and 255

tracks.

Caution!

• DVD-R and CD-R/RW discs recorded using a personal computer

or a DVD or CD recorder may not play if the disc is damaged or

dirty, or if there is dirt or condensation on the player’s lens.

• If you record a disc using a personal computer, even if it is

recorded in a compatible format, there are cases in which it may

not play because of the settings of the application software used

to create the disc. (Check with the software publisher for more

detailed information.)

• Unfinalized DVD-R discs cannot be played.

• Unfinalized CD-R/RW discs can be played, but not all time

information (playing time, etc.) will be displayed.

• For more information on using DVD-R and CD-R/RW discs, see

Handling discs starting on page 37.

ALL

ENGLISH

BASIC CONNECTION

• First of all, read through the instructions before connecting other equipment. Make sure that this unit and other equipment to be

connected are set to the standby mode or off, and disconnect the AC mains before starting connection. In order for air to

circulate freely, please do not block ventilation holes of any of the equipment. Select the appropriate screen size at the initial

setting according to your TV set, conventional 4:3 or wide screen 16:9.

• TV MODE SETTING

VIDEO

S-VIDEO

COMPONENT

DIGITAL OUTPUT

COAXIALOPTICAL

REMOTE CONTROL

AUDIO

OUTPUT

VIDEO

OUTPUT

OUTIN

INTERNAL

EXTERNAL

S-VIDEO

AUDIO

OUTPUT

VIDEO

OUTPUT

L R

Note

• Do not connect your DVD-player via your VCR, because the video quality could be distorted by the copy protected system.

S -VIDEO OUT CONNECTION

Note

From the SETUP menu display, set the OUTPUT MODE to S-VIDEO.

a. audio cable (optional)

To audio input connectors on TV. (red, white)

b. S-Video cable (optional)

To S-Video input connector on TV.

Setup Menu / Video Video Output

Progressive Output mode Video Jack S-Video Jack Component Jack

OFF YCbCr Composite

Interlace mode (480i)

ON YCbCr

Progressive mode (480p)

OFF S-Video Composite S-Video

ENGLISH

VIDEO

S-VIDEO

COMPONENT

DIGITAL OUTPUT

COAXIALOPTICAL

REMOTE CONTROL

AUDIO

OUTPUT

VIDEO

OUTPUT

OUT

INTERNAL

EXTERNAL

AUDIO

OUTPUT

VIDEO

OUTPUT

VIDEO

S-VIDEO

COMPONENT

DIGITAL OUTPUT

COAXIALOPTICAL

REMOTE CONTROL

AUDIO

OUTPUT

VIDEO

OUTPUT

OUTIN

INTERNAL

EXTERNAL

AUDIO

OUTPUT

COMPONENT

L R

Composite video out Connection

Note

From the SETUP menu display, set the Progressive to OFF.

Component video out connection (480i/480p)

Note

• If your TV has progressive (480p) video input, from the SETUP menu display, set the progressive mode to ON and also set the

output mode to YCbCr.

• If your TV has interlace (480i) video input, from the SETUP menu display, set the progressive mode to OFF and also set the output

mode to YCbCr.

• All HD TV are compatible with this player but some TV may cause artifacts in the picture.

• If you set progressive mode to ON [progressive scan mode], you can’t see the picture with your Analog TV or some digital TV. In this

case, press stop button for 5 seconds of your remote controller then you can see the picture on the interlace mode with your TV.

d. Audio cable (optional)

To audio input connectors on TV. (red, white)

e. Component-Video cable (optional)

To Component video input connectors on TV.

c. Video/audio cable (accessory)

To audio input connectors on TV. (red, white)

To video input connector on TV. (yellow)

ENGLISH

VIDEO

S-VIDEO

COMPONENT

DIGITAL OUTPUT

COAXIALOPTICAL

REMOTE CONTROL

AUDIO

OUTPUT

VIDEO

OUTPUT

OUTIN

INTERNAL

EXTERNAL

AUDIO

OUTPUT

L R

CLEAR

F/P

MODE

TUNING/PRESET

MEMORY

PHONES

SURROUND

AV SURROUND RECEIVER SR4300

STANDBY

POWER ON/STANDBY

MUTE

S-DIRECT

HT-EQ

DSS/VCR2

DVD

CDR/MD

TAPE

TUNER

A/D

DIMMER

6.1CH-IN

VCR1

VOLUME

DOWN

Analog Audio Connection

Note

• Make analog audio connections to a stereo amplifier or receiver.

• Analog audio connections can also be made to a TV or monitor with stereo input jacks.

• When playing DTS-encoded discs, excessive noise may be output from the Analog Audio out jack. This is not a malfunction.

g. Audio cable (optional)

To audio input connectors on AV amplifier or receiver.

ENGLISH

DISC DIGITAL OUT

Dolby Digital

DTS

PCM

MPEG 2

Dolby Digital Dolby Digital

DTS DTS

PCM PCM

MPEG 2 MPEG 2

Dolby Digital PCM

DTS DTS

PCM PCM

MPEG 2 PCM

SETUP menu

Digital Out

OFF

BTSTREAM

PCM

VIDEO

S-VIDEO

COMPONENT

DIGITAL OUTPUT

COAXIALOPTICAL

REMOTE CONTROL

AUDIO

OUTPUT

VIDEO

OUTPUT

OUT

INTERNAL

EXTERNAL

COAXIALOPTICAL

DIGITAL OUTPUT

CLEAR

F/P

MODE

TUNING/PRESET

MEMORY

PHONES

SURROUND

AV SURROUND RECEIVER SR4300

STANDBY

POWER ON/STANDBY

MUTE

S-DIRECT

HT-EQ

DSS/VCR2

DVD

CDR/MD

TAPE

TUNER

A/D

DIMMER

6.1CH-IN

VCR1

VOLUME

DOWN

Digital Audio Connection

Note

• When a recorded in a Dolby Digital or DTS is loaded, noise will be output if you have made connections via the digital audio jacks

to a receiver or amplifier that cannot decode a Dolby Digital or DTS digital bitstream.

In this case, be sure to set up the SETUP, Audio setting; Digital out to PCM or OFF.

h, i. Optical (h) or coaxial (i) audio cable (optional)

To optiacl or coaxial digital input connectors on AV amplifier or receiver.

• DIGITAL OUT SETTING

AV amplifier or receiver with built-in

Dolby Digital and DTS decorder.

Subwoofer

Front speaker

(left)

Surround speaker (left)

Center speaker

Front speaker

(right)

Surround speaker (right)

ENGLISH

VIDEO

S-VIDEO

COMPONENT

DIGITAL OUTPUT

COAXIALOPTICAL

REMOTE CONTROL

AUDIO

OUTPUT

VIDEO

OUTPUT

OUTIN

INTERNAL

EXTERNAL

REMOTE CONTROL

OUTIN

INTERNAL

EXTERNAL

CLEAR

F/P

MODE

TUNING/PRESET

MEMORY

PHONES

SURROUND

AV SURROUND RECEIVER SR4300

STANDBY

POWER ON/STANDBY

MUTE

S-DIRECT

HT-EQ

DSS/VCR2

DVD

CDR/MD

TAPE

TUNER

A/D

DIMMER

6.1CH-IN

VCR1

VOLUME

DOWN

REMOTE CONTROL

OUT IN

INTERNAL

EXTERNAL

System Control Connection

By connecting this DVD player to another Marantz audio component using a supplied System Control cable, you can remotely

operate the components as a single system.

• When connecting to component with a remote sensor, be sure to connect the REMOTE CONTROL IN jack of this DVD player to

the REMOTE CONTROL OUT jack of the component with the remote sensor.

• When connecting to component which is not equipped with a remote sensor, be sure to connect the component to the REMOTE

CONTROL OUT jack of this DVD player.

Remote switch

• When using this DVD player independently, set this switch to INTERNAL. When using this DVD player in a system with a

Marantz receiver equipped with a remote sensor, set the switch to EXTERNAL.

j. System conrol cable (optional)

To remote control output connector on AV amplifier or receiver.

ENGLISH

qw retyui

o!0!1 !2!3 !4

Front Panel

CONTROLS & DISPLAY

q POWER (STANDBY/ON) button

To switch the unit On or into STAND BY when connected to AC

power outlet.

w STAND BY indicator

Lights when Power is STAND BY mode.

e REMOTE SENSOR

Receives a light signal from the remote controller.

r DISC TRAY

To load or unload a disc. Put a disc to be played on here.

t FL DISPLAY

Displays operation status (Refer to Page11 FL Display).

y PLAY button

To play the loaded disc. Press this button to go to the preferred

item when the menu is displayed on the TV screen.

u STOP button

To stop playing. If using a Video CD 2.0, SVCD or CVD with

PBC, this button works as a RETURN function to move to the

previous menu.

i PAUSE/STEP button

Used to view one frame at a time during play. When you con-

tinue pressing this button, it will function continuously. Press

PLAY button for normal play.

o OPEN/CLOSE button

To open or close the disc tray.

0 FR (Fast Reverse) button

To play the disc fast reverse. It can also be used as a Slow

Reverse button when in pause or step mode, and also a left

arrow(

) button when in menu mode.

!1 FF (Fast Forward) button

To play the disc fast forward. It can also be used as a Slow

Forward button when in pause or step mode, and also a right

arrow(

) button when in menu mode.

2 PREV button

To skip back from the current chapter (for DVD) or track (for

VCD or CD). When in menu mode, this button also works as a

down arrow(

) button. If playing a Video CD with PBC, this

button works as the PREV button to move to the previous play

list.

3 NEXT button

To skip forward to the next chapter (for DVD) or track (for VCD

or CD). When in menu mode, this button also works as an up

arrow(

) button. If playing a Video CD with PBC, this button

works as the NEXT button to move to the next play list.

4 MENU button

To view the general information for the current loaded disc such

as language selection, audio output selection and subtitle lan-

guage selection and so on.

ENGLISH

as dfghj k

l¡0 ¡1 ¡2

Display

a CDDA/SVCD/DVD/MP3

Illuminates the type of a disc loaded on disc tray.

s TITLE/CHAPTER

Illuminates the information of the TITLE or CHAPTER of the

DVD disc under play.

d PLAY/PAUSE/STEP

Illuminates the current operation mode.

f ROTATION

Rotates when the disc is spinning.

g ANGLE

Indicates the current disc being played is viewed as multi angle.

This function only works for discs having scenes recorded at

different angles.

h SUB-T

Indicates the current disc under play has multi subtitle. This func-

tion only works for discs having recordings with multiple subtitle

languages.

j AUDIO

Indicates the current disc under play has multi audio soundtrack

languages. This function only works for discs having recordings

in multiple audio soundtrack languages.

k DTS, LPCM, MPEG,

Indicates the audio type of the disc under play is DTS, LPCM,

MPEG or 2.

l SHUFFLE/PROGRAM

Illuminates under shuffle/program mode.

(Video CD with PBC off or CDDA only)

¡0 REPEAT T, C, 1, A-B, ALL

Illuminates when the current play mode is under repeat title,

chapter, track (single), A-B, disc (all) respectively.

¡1 TIME

Indicates time information and sometimes system information

like STOP, MENU and so on.

¡2 L, C, R, LFE, LS, S, RS

Indicates the audio channel information of the disc under play.

For DVD discs having the Dolby Digital audio.

ENGLISH

Rear Panel

VIDEO

S-VIDEO

COMPONENT

DIGITAL OUTPUT

COAXIALOPTICAL

REMOTE CONTROL

AUDIO

OUTPUT

VIDEO

OUTPUT

OUTIN

INTERNAL

EXTERNAL

SERIAL NO.

zxc v b n

m, .

z DIGITAL OUT (OPTICAL)

Connects digital audio under play mode into an AV amplifier or

a receiver equipped with digital audio decoder for you to enjoy

the theatre-quality sound in your home.

Note

•

Remove the dust protection cap from the optical digital audio output

connector and connect the cable firmly so that the configurations of

both the cable and connector match.

• Do not connect to the digital audio input of an amplifier that does

not have Dolby Digital and dts decoder when you set the digital out

option of setup information to BITSTREAM.

x DIGITAL OUT (COAXIAL)

Connects digital audio under play mode into an AV amplifier or

a receiver equipped with digital audio decoder for you to enjoy

the theatre-quality sound in your home.

c AUDIO OUT

Analogue 2 channel (L/R) audio output in order to connect to a

TV or stereo amplifier.

v VIDEO OUT

Connects composite video signal to Composite Video input con-

nector of TV or monitor to achieve high fidelity colour reproduc-

tion.

b COMPONENT VIDEO OUT (480i or 480p)

Connects component video signal to component video input

connector on TV, if your TV supports interlace video input (480i)

or Progressive video input (480p).

n AC in power cord connection terminal

Creates POWER between wall outlet and the unit.

m S-VIDEO OUT

Connects to TV or monitor equipped with S-VIDEO input. In

order to achieve a sharper and cleaner picture than that when

connected via VIDEO OUT (composite video).

, System Control in / out jack

Connect this DVD player to another Marantz Component, to

operate the components as a single system (page 9).

. System Control external / internal switch

When using this DVD player independently, set this switch to

“INTERNAL” (page 9).

ENGLISH

Remote Controller Unit

Numbers for each button on the remote control unit will be indicated in parenthesis mark starting from the next page.

q POWER

w NUMERIC BUTTONS (1-9, 0)

e CLEAR

r MENU/RETURN

t PREV

y ENT (ENTER)

u FR/SR

i SETUP

o PAUSE/STEP

!0 ZOOM

(ANGLE) / DIGEST

!2 SHUFFLE

!3 MARKER

!4 VOCAL

!5 PAL/NTSC

!6 OPEN/CLOSE

!7 DISPLAY

!8 TOP MENU/PBC

!9 NEXT

@0 ARROW (Left, Right, Up, Down)

@1 FF/SF

@2 STOP

@3 PLAY

@4 SUBTITLE

@5 AUDIO

@6 A-B

@7 REPEAT

@8 3D SOUND

@9 PROG (PROGRAM)

ENGLISH

1. General Function for Remote Control Unit

1. POWER q

Activates the unit POWER ON or into STANDBY.

2. OPEN/CLOSE !6

After pressing power button, press OPEN/CLOSE button to open

or close the disc tray. If pressed under STAND BY, power is

automatically turned on and the tray is opened.

3. NUMERIC w

Used from the menu to select, title/chapter search, time search

and direct track number.

4. CLEAR e

Used when discarding wrong number input, returning to normal

play during slow or search. This button can also be used when

clearing zoom state.

5. PAL/NTSC !5

Set up TV type according to type supported by user’s TV.

2. Basic Function

1. PLAY button @3,

Use this button to play.

2. STOP button @2,

To stop the current playing mode, press STOP button.

Press the stop key for 5 seconds to convert progressive scan

mode into interlace mode.

3. PAUSE / STEP button o,

Use this button to play one frame at a time. To do step back-

ward, press this button during reverse operation i.e. fast reverse

or slow reverse.

4. FF/SF @1,

To play a disc fast forward or slow forward. During pause or

step state, this button works as Slow Forward. (Page 21)

5. FR/SR u,

To play a disc fast reverse or slow reverse. During pause or

step state, this button works as Slow Reverse. (Page 21)

6. NEXT !9,

Used to move to the next chapter (DVD) or track (VCD or CDDA)

from the current chapter or track.

Pressing this button shows next play list when playing VCD with

PBC. (Page 21)

7. PREV t,

Used to move to the previous chapter (DVD) or track (VCD or

CDDA) from the current chapter or track.

Pressing this button shows previous play list when playing VCD

with PBC. (Page 21)

3. Advanced Functions

1. REPEAT @7 (Except VCD with PBC on)

To set up the repeat viewing during play. Two repeat modes are

possible. When using a DVD, “CHAPTER REPEAT ON” repeats

the current chapter and “TITLE REPEAT ON” repeats all chap-

ters in the current title.

When using a VCD with PBC off or CDDA, “REPEAT ONE” re-

peats the current track and

“

REPEAT ALL

”

repeats all tracks on

the disc. To clear the repeat function, press this button until you

see REPEAT OFF on the TV screen. Turn off PBC to use this

function on VCD with PBC included.

(Page 26)

2. A-B @6 (Except MP3)

To repeat the selected segment. The moment you press this

button during play, the starting point for the desired segment is

selected. When you press this button again, the ending point is

selected and starts repeated play of the selected segment auto-

matically. Press this button again to cancel the repeating of the

selected segment.

(Page 25)

3. PROG (PROGRAM

(VCD with PBC off and CDDA only))

Use this button to play the tracks, which you want to watch. You

can program desired tracks up to the total programmed time of

99 minutes. Turn off PBC to use this function on VCD with PBC

included

(Page 27)

4. SHUFFLE !2 (VCD with PBC off and CDDA only)

Use this button to play the loaded disc in a random order. Turn

off PBC to use this function on VCD with PBC included

(Page 27)

5. DIGEST !1 (VCD with PBC off and CDDA only)

Use this button to do quick search or preview the disc contents.

This function shows thumbnail contents of the loaded disc. Turn

off PBC to use this function on VCD with PBC included. (Page 28)

6. ZOOM !0 (Except CDDA and MP3)

Enlarges DVD or VCD screen images up to eight times. You

may also move the image using left, right, up and down arrow

button @0.

(Page 31)

7. MARKER !3 (Except MP3)

Stores playing point up to five locations for the easy search,

when you want to move to the stored playing point.

(Page 29)

8. DISPLAY !7 (Except MP3)

This button has multiple functions. Supports search of a chap-

ter/title for DVD or a track for VCD and CDDA. Also shows infor-

mation for elapsed or remaining time. On DVD, you may see bit

rate meter. (Page 29)

9. 3D SOUND @8 (CDDA and MP3 only)

Adds 3D surround effect to analogue audio output. There are 4

surround modes. (Page 25)

10. PBC !8 (VCD with PBC only)

You may turn on or off the PBC function by pressing this button.

When the VCD with PBC is loaded, PBC function is enabled au-

tomatically. Video CD 2.0, SVCD and CVD are PBC controllable.

11. VOCAL !4

If the disc is a Dolby Digital Karaoke disc, the following modes

are available:

No vocal / Left vocal / Right vocal / Both vocal / Mixed vocal

“Mixed vocal” means sending (Left vocal + Right vocal) / 2 to

both left and right speaker.

ENGLISH

4. DVD Function

1. TOP MENU !8

Used to display the title menu of the loaded DVD disc. This

function is disc dependent. A DVD disc may not contain the title

menu. (Page 19)

2. MENU r

Used to display the contents menu of the loaded DVD disc. This

function is disc dependent. A DVD disc may not contain a con-

tents menu. (Page 19)

(ANGLE !1)

Used to select a different angle when the loaded DVD disc sup-

ports multiple angles. This function is a disc dependent. Many

DVD discs don’t support multiple angles. (Page 23)

4. SUBTITLE @4

Used to change the subtitle language to a different language or

off from the one selected at the initial settings, when the loaded

disc supports multiple languages.

(Page 23)

5. AUDIO @5

Used to change the audio language to a different language from

the one selected at the initial settings, when the loaded disc sup-

ports multiple audio languages.

(Page 22)

5. SETUP Function

1. ARROW @0,

Used to move to the desired menu and moves the image center

of an enlarged screen in zoom mode. Also can be used in marker

or display function.

2. ENT(ENTER y)

Used to select the menu item. When pressed during STOP,

PAUSE, STEP, SEARCH or SLOW state, it also cancels the

current state and converts to PLAY mode.

3. SETUP i

Sets up the various operation information of this unit to custom-

ize DVD performance. (Page 32)

• This remote control supports two remote control codes: DVD1 and DVD2.

• When the unit is shipped from the factory, the remote control is set to DVD1.

• To set the remote control to DVD2, hold down both the “

(Stop)” button and the “2” number button on the remote control for at least five

seconds. (If the batteries in the remote control are replaced while the remote control is set to DVD2, the setting will revert to DVD1.)

• To set the remote control back to DVD1, hold down both the “

(Stop)” button and the “1” number button on the remote control for at least five

seconds.

• To check which remote control code is set at STOP mode, hold down both the Stop and PAUSE buttons; the current setting (either “DVD1” or

“DVD2”) will be displayed in the display window on the main unit.

• Also set the REMOT CODE on the main unit to the same setting as the remote control.

Press SETUP buttom for longer than five seconds in stop mode.

Use the Up/Down buttom (

/ ) to select the type of REMOTE CODE (DVD1/DVD2), and press ENTER you want to set.

To exit the REMOTE CODE setting, press SETUP.

(This setting is set to DVD1 when the unit is shipped from the factory.)

ENGLISH

OA D I N G

BASIC FUNCTION

Open / Close Disc Tray

1. Connect to AC power

When AC power is connected, the STAND-BY INDICATOR on the front panel is turned on.

2. Press POWER button

When the POWER button is pressed, the STAND-BY INDICATOR turns off. TV or monitor screen shows the initial pictures as

shown below.

3. Press OPEN/CLOSE button

When the disc tray opens, OPEN message is displayed on TV screen and Fluorescent display on front panel simultaneously.

4. Load your selected disc using disc tray guide with logo-printed side up

5. Press OPEN/CLOSE button again to close the disc tray

PEN

Page is loading ...

Marantz PMD910 User manual

Brand: Marantz

Model: PMD910

Category: DVD players

Type: User manual

Download PDF

report

Marantz PMD910 User manual

Marantz PMD910 User manual

Related papers

Other documents