JBL L series User manual

Category
Soundbar speakers
Type
User manual

JBL L series

JBL L series are high-quality loudspeakers designed for a variety of uses. They feature a wide frequency response, high power handling, and low distortion, making them ideal for both home and professional audio applications.

Some of the features and capabilities of the JBL L series include:

  • Wide frequency response: The JBL L series loudspeakers have a wide frequency response that extends from 50Hz to 20kHz, making them capable of reproducing a wide range of audio content.
  • High power handling: The JBL L series loudspeakers can handle up to 200 watts of power, making them suitable for use in high-volume applications.

JBL L series

JBL L series are high-quality loudspeakers designed for a variety of uses. They feature a wide frequency response, high power handling, and low distortion, making them ideal for both home and professional audio applications.

Some of the features and capabilities of the JBL L series include:

  • Wide frequency response: The JBL L series loudspeakers have a wide frequency response that extends from 50Hz to 20kHz, making them capable of reproducing a wide range of audio content.
  • High power handling: The JBL L series loudspeakers can handle up to 200 watts of power, making them suitable for use in high-volume applications.
CROSSOVER
NETWORK
013-7600-05278-EP
WOOFER
16PR80BYG-DW02-EP
TWEETER
18DA25BF-DT01-EP
BLK
RED
RED
BLK
LS3
26C
1
04
-
c05
27
8
a0
0
-e
b
a
c
L
1
R3
R
2
-
T
+
C3
W+
C2
R
4
R
1
W
-
a
b
SWW
I
N
-
C1
SWT
IN+
EXPLODED
VIEW
WIRING DIAGRAM
9
11
11
7
6
10
5
4
3
2
1
8
JBL LS326C Studio
L Series
JBL Loudspeaker Troubleshooting/Repair Tips
Most customers prefer to do simple loudspeaker repairs themselves. By following the steps below, a majority of loudspeakers can be returned to
their original factory performance with minimum effort. Choose the example that best describes the problem you are experiencing.
Problem 1: No sound or distorted sound from one loudspeaker in a pair (or set)
Connect the dead/distorting loudspeaker to a different amplifier channel (one that had a functioning loudspeaker connected to it). If it functions
normally, the problem is not loudspeaker-related. If the loudspeaker still makes no sound or sounds distorted, a wire may have become loose
or disconnected, the network (also known as a crossover) may be defective, the drivers (woofer, tweeter, etc.) may be defective or, in very rare
cases, all may be defective.
Refer to the wiring diagram and exploded view below. The network is a small circuit board found on the inside of the terminal cup, or mounted to
an inside wall of the enclosure. It sends low-frequency sounds to the woofer, high-frequency sounds to the tweeter and, if applicable, mid-frequency
sounds to the midrange driver. Make sure all wires are secure and connected. Look for components on the network that look burnt, “bulged,”
or abnormal. If everything looks normal, connect the network to the drivers from another matching loudspeaker. MAKE SURE you attach the
correct wires to each driver – mid- and low-frequency sounds can damage the tweeter! If there is still no sound or distorted sound, the network
is defective. If there is clean undistorted sound, the drivers are defective.
Problem 2: No sound or distorted sound from one or more (but not all) drivers in an enclosure
Remove the problem driver(s) from the enclosure and make sure all wires are secure and connected. If they are, proceed with the following test:
Woofer or midrange driver – Connect the driver’s + and – input terminals directly to the loudspeaker wires from your receiver/amplifier and play
some music at a reasonable volume. If the driver now sounds normal (produces a clean, undistorted sound), the network is most likely defective.
Tweeter – Replace the tweeter with a functioning tweeter from another loudspeaker. If the tweeter now functions normally (produces clean,
undistorted sound), the original tweeter is defective. If the replacement tweeter also sounds distorted or produces no sound, the network is
most likely defective.
Problem 3: Loudspeakers distort, rattle or pop at higher volumes
This is usually NOT a loudspeaker problem. Common causes are too much power (playing the loudspeakers too loud and causing them to distort),
an amplifier with not enough power (the amplifier can’t produce the required volume without distorting), excessive equalization (turning the tone
controls too far clockwise, and/or engaging the loudness/bass boost button on your receiver) or some combination of the above. If only one
loudspeaker is exhibiting the problem, and you’re confident that it’s not caused by too little power/too much power/excessive equalization, see
solutions for Problems 1 and 2.
ITEM PART NO. DESCRIPTION QTY.
1 329-060-05274-0WAE GRILLE ASS’Y 1
2 352-CM04050D949-E SCREW, DOG EAR 4
3 18DA25BF-DT01-EP TWEETER ASS’Y 1
4 248-000-05008-0WAE BAFFLE ASSEMBLY 1
(BAFFLE, DOG EARS, CAPS)
5 16PR80BYG-DW02-EP 6-1/2" WOOFER 1
6 013-7600-05278-EP CROSSOVER NETWORK 1
7 352-CM04012D948-E SCREW FOR TWEETER BRIDGE, 11
NETWORK AND WOOFER
8 316-PC-05201-0TAE LOGO, GRILLE 1
9 051-C05275A-E SWITCH – TWEETER LEVEL 1
SWITCH ASSEMBLY
ITEM PART NO. DESCRIPTION QTY.
10 051-C05278A-E SWITCH – BOUNDARY 1
COMPENSATION
11 352-EM02508C961-E SCREW FOR SWITCHES 4
12 221-060-05165-0TAE PAINT TEMPLATE 1
13 402-000-05697-E OUTER CARTON 1
14 404-000-05093-E CUTTING TEMPLATE 1
15 405-000-05008-E WARRANTY CARD 1
16 406-000-05527-E OWNER’S MANUAL 1
17 431-000-05950-E FOAM PACKING (TOP) 1
18 431-000-05957-E FOAM PACKING (BOTTOM) 1
LS326C ROUGH-IN FRAME PART NO. RIF6CS
  • Page 1 1

JBL L series User manual

Category
Soundbar speakers
Type
User manual

JBL L series

JBL L series are high-quality loudspeakers designed for a variety of uses. They feature a wide frequency response, high power handling, and low distortion, making them ideal for both home and professional audio applications.

Some of the features and capabilities of the JBL L series include:

  • Wide frequency response: The JBL L series loudspeakers have a wide frequency response that extends from 50Hz to 20kHz, making them capable of reproducing a wide range of audio content.
  • High power handling: The JBL L series loudspeakers can handle up to 200 watts of power, making them suitable for use in high-volume applications.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI