JVC GR-AX860 User manual

Category
Camcorders
Type
User manual
GR-AX860
COMPACT VHS CAMCORDER
INSTRUCTIONS
YU30052-552-1
Compact VHS
PAL
CONTENTS
GETTING STARTED
6
RECORDING
14
Basic Recording ...................... 14
Basic Features ........................ 15
Video Light ........................... 17
Advanced Features .................. 18
Date/Time Insert .................... 18
Snapshot ................................ 19
Digital Image Stabilizer
(D.I.S.) ................................... 20
Exposure Control .................... 20
White Balance Adjustment ...... 21
Focusing ................................ 22
Programme AE With Special
Effects .................................... 24
Fade/Wipe ............................. 26
Using Menu For Detailed
Adjustment............................. 28
Instant Titles........................... 30
Self-Timer .............................. 32
Animation .............................. 33
Time Lapse ............................. 33
PLAYBACK
34
Using The Cassette Adapter ........ 34
Basic Connections .................... 35
Basic Playback ....................... 36
Features ............................... 37
EDITING
38
Tape Dubbing ......................... 38
Random Assemble Editing [R.A.Edit] ...
38
Insert Editing ......................... 42
Audio Dubbing ........................ 43
USER MAINTENANCE
44
TROUBLESHOOTING
45
INDEX
47
Controls ............................... 47
Connectors ............................ 48
Indicators ............................. 48
Other Parts ........................... 48
Viewfinder ............................ 49
Terms .................................. 50
CAUTIONS
51
SPECIFICATIONS
53
2
Dear Customer,
Thank you for purchasing the JVC Compact VHS
camcorder. Before use, please read the safety
information and precautions contained in the following
pages to ensure safe use of your new camcorder.
SAFETY
PRECAUTIONS
Using This Instruction Manual
• All major sections and subsections are listed in the Table
Of Contents (
Z cover page).
• Notes appear after most subsections. Be sure to read
these as well.
• Basic and advanced features/operation are separated for
easier reference.
It is recommended that you . . .
..... refer to the Index (
Z pgs. 47 – 50) and
familiarize yourself with button locations, etc. before
use.
..... read thoroughly the Safety Precautions that follow and
cautions (
Z pgs. 51, 52). They contain extremely
important information regarding the safe use of your
new camcorder.
IMPORTANT
Connection to the mains supply in the United
Kingdom.
DO NOT cut off the mains plug from this equipment.
If the plug fitted is not suitable for the power points in
your home or the cable is too short to reach a power
point, then obtain an appropriate safety approved
extension lead or consult your dealer.
BE SURE to replace the fuse only with an identical
approved type, as originally fitted, and to replace the
fuse cover.
If nontheless the mains plug is cut off ensure to remove
the fuse and dispose of the plug immediately, to avoid
a possible shock hazard by inadvertent connection to
the mains supply.
If this product is not supplied fitted with a mains plug
then follow the instructions given below:
DO NOT make any connection to the Larger Terminal
coded E or Green.
The wires in the mains lead are coloured in accord-
ance with the following code:
Blue to N (Neutral) or Black
Brown to L (Live) or Red
If these colours do not correspond with the terminal
identifications of your plug, connect as follows:
Blue wire to terminal coded N (Neutral) or coloured
black.
Brown wire to terminal coded L (Live) or coloured
Red.
If in doubt — consult a competent electrician.
This unit is produced to comply with Standard IEC
Publ. 65.
Warning on lithium battery
The battery used in this device may present a fire or
chemical burn hazard if mistreated. Do not recharge,
disassemble, heat above 100°C or incinerate.
Replace the battery with Panasonic (Matsushita
Electric), Sanyo or Maxell CR2025; use of another
battery may present a risk of fire or explosion.
n Dispose of used battery promptly.
n Keep away from children.
n Do not disassemble and do not dispose of in fire.
CAUTIONS:
n To prevent shock, do not open the cabinet. No user
serviceable parts inside. Refer servicing to qualified
personnel.
n When you are not using the AC Power Adapter/
Battery charger for a long period of time, it is
recommended that you disconnect the power cord
from AC outlet.
NOTES:
The rating plate (serial number plate) and safety
caution are on the bottom and/or the back of the
main unit.
The rating plate (serial number plate) of the AC
Power Adapter/Charger is on its bottom.
WARNING:
TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR
MOISTURE.
Crossed Out Dust Bin Mark
n The Crossed Out Dust Bin Mark on
the battery pack indicates that the
product complies with Directives
91/157/EEC and 93/86/EEC.
n Nickel-Cadmium (Ni-Cd) battery
pack must be recycled or disposed
of properly.
3
This camcorder is designed to be used with PAL-type
colour television signals. It cannot be used for
playback with a television of a different standard.
However, live recording and viewfinder playback are
possible anywhere. Use the BN-V12U/BN-V22U/BN-
V25U battery packs and, to recharge them, the
provided multi-voltage AC Power Adapter/Charger. (An
appropriate conversion adapter may be necessary to
accommodate different designs of AC outlets in
different countries.)
n This camcorder is designed exclusively for the VHS-C
video cassette. Only cassettes marked VHS-C can be
used with this unit.
n HQ VHS is compatible with existing VHS equipment.
PAL
SOME DO’S AND
DON’TS ON THE SAFE
USE OF EQUIPMENT
This equipment has been designed and manufactured to
meet international safety standards but, like any electrical
equipment, care must be taken if you are to obtain the
best results and safety is to be assured.
DO read the operating instructions before you attempt to
use the equipment.
DO ensure that all electrical connections (including the
mains plug, extension leads and interconnections
between pieces of equipment) are properly made and
in accordance with the manufacturer’s instructions.
Switch off and withdraw the mains plug when making
or changing connections.
DO consult your dealer if you are ever in doubt about the
installation, operation or safety of your equipment.
DO be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in
any doubt about it working normally, or if it is
damanged in any way — switch off, withdraw the
mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose
dangerous voltages.
DON’T leave equipment switched on when it is unat-
tended unless it is specifically stated that it is
designed for unattended operation or has a standby
mode. Switch off using the switch on the
equipment and make sure that your family knows
how to do this. Special arrangements may need to
be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios
so that you are distracted from the requirements of
road safety. It is illegal to watch television whilst
driving.
DON’T listen to headphones at high volume, as such use
can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for
example with curtains or soft furnishings.
Overheating will cause damage and shorten the
life of the equipment.
DON’T use makeshift stands and NEVER fix legs with
wood screws — to ensure complete safety always
fit the manufacturer’s approved stand or legs with
the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or
moisture.
ABOVE ALL
NEVER let anyone especially children push anything
into holes, slots or any other opening in the case
— this could result in a fatal electrical shock;
NEVER guess or take chances with electrical equipment
of any kind — it is better to be safe than sorry!
4
MAJOR FEATURES
REMEMBER
The Logical Choice
The only compact video
cassettes that can be
used with your VHS VCR*
Programme AE with Special
Effects (
Z pg. 24)
n Cinema n Sepia n Twilight n Sports
n High Speed (1/2000 sec.) Shutter
n Classic Film n Strobe n Slow Shutter
Multi Function Control
(
Z pg. 20 – 33)
Random Assemble Editing
(
Z pg. 38 – 41)
W
T
W
T
W
T
W
T
Zoom-in
Zoom-out
Digital Wipes and Fades
(
Z pg. 26)
Black Fader Blue Fader
Mosaic Fader Shutter Wipe
Slide Wipe Corner Wipe
Dissolve Auto Select
Digital Hyper Zoom (Z pg. 15)
Digital Image Stabilizer
(
Z pg. 20)
Built-In Auto Light (Z pg.17)
PROVIDED ACCESSORIES
8
8
2
2
5
5
4
4
1
1
6
6
3
3
7
7
AC Power Adapter/
Charger AA-V11EK
Battery Pack
BN-V12U
Cassette Adapter
C-P7U
Remote Control
Unit RM-V706U
Editing Cable
DC Cord
Lithium Battery
CR2025
Shoulder Strap Cable adapter
5
QUICK OPERATION GUIDE
SUPPLY POWER
Using the battery pack
1
Hook-on the battery pack’s top end to the
camcorder. (Charging procedure, Z P. 6)
2 Push in the battery pack until it locks into
place.
To remove the battery pack
Slide BATT. RELEASE and pull out the battery
pack.
SHOOTING
1 Slide the LENS COVER open/close knob to
open the lens cover.
2 Set the power switch to “CAMERA”.
— The power indicator will light and an
image will appear in the viewfinder.
3 Press RECORDING START/STOP.
— Recording starts.
To stop recording temporarily, momentarily
press the Recording Start/Stop button once
again.
(For more details, Z P. 14)
2
Push in.
1
Hook on.
BATT. RELEASE
3
1
PUSH
Insert.
EJECT
2
2
REW
1
Set to “PLAY”
1
LENS COVER
open/close knob
3
Recording Start/Stop button
2
Set to “CAMERA”
INSERTING A VIDEO
CASSETTE
1 Slide EJECT.
2 Insert a video cassette.
3 Press PUSH.
(For more details, Z P. 11)
STOP
3
PLAY/PAUSE
PLAYBACK
1 Set the power switch to “PLAY”.
2 Press REW.
The tape will automatically stop at the
beginning of the tape.
3 Press PLAY/PAUSE.
Playback starts and the playback picture
appears in the viewfinder.
To stop playback, press STOP.
(For more details, Z P. 36.)
n
Or simply play back the tape on a VHS
VCR using the Cassette Adapter.
Z
P. 34
6
GETTING STARTED
Power
This camcorder’s 3-way power supply system lets you
choose the most appropriate source of power.
NOTES:
No function is available without power supply.
Use only specified power supply.
Do not use provided power supply units with other equipment.
CHARGING THE BATTERY PACK
SUPPLY POWER
1
Connect the charger’s AC power cord to a wall
outlet. The power indicator lights.
ATTACH BATTERY PACK
2
Align the marks and slide the battery pack in the
direction of the arrow until it locks in place.
The CHG. indicator lights.
DETACH BATTERY PACK
3
When charging is completed, the END indicator
lights. Slide the battery pack opposite the direction
of the arrow.
USING THE BATTERY PACK
ATTACH BATTERY PACK
1
Hook its top end to the camcorder and push the
battery pack in until it locks in place.
DETACH BATTERY PACK
2
Slide BATT. RELEASE and pull out the battery pack.
BATT. PACK RECORDING TIME
BN-V12U approx. 1 hr. (35 min.)
BN-V22U approx. 2 hrs. 10 min. (1 hr. 20 min.)
BN-V25U approx. 2 hrs. 50 min. (1 hr. 50 min.)
BATT. PACK CHARGE DISCHARGE
BN-V12U approx. 1 hr. 10 min. approx. 3 hrs. 30 min.
BN-V22U approx. 2 hrs. 10 min. approx. 7 hrs.
BN-V25U approx. 2 hrs. 40 min. approx. 10 hrs.
REFRESH indicatorREFRESH switch
CHG. (charge) indicator
To AC outlet
Marks
END
indicator
Hook on.
Push in.
BATT. RELEASE
POWER
indicator
ATTENTION:
Before detaching the power source,
make sure that the camcorders power
is turned off. Failure to do so can result
in a camcorder malfunction.
( ): When the Video Light is on
**REFRESH
The AC power adapter features a REFRESH function that allows
you to fully discharge the battery pack before recharging.
To discharge the battery . . .
..... attach the battery pack to the adapter as shown in the
illustration to the left. Then push REFRESH. The REFRESH
indicator lights when discharging starts, and goes out when
discharging is complete.
7
**CHARGE MARKER
A charge marker is provided on the battery pack to
help you remember whether it has been charged or
not. Two colours are provided (red and black)—you
choose which one means charged and which
means discharged.
NOTES:
The recording time per charge is affected by such factors as the time spent in Record/Standby mode and
the frequency of zooming. It is safer to have spare battery packs.
Charging times noted on page 6 are for fully discharged battey pack, and discharging times are for fully
charged battery pack.
Charging and discharging times vary according to the ambient temperature and the status of the battery
pack.
Remember to set the charge marker after charging a battery pack or after detaching a discharged one from
your camcorder.
Perform the REFRESH function after no less than 5 chargings.
High temperatures can damage the battery pack, so use only where good ventilation is available. Don’t
allow it to discharge in container, such as a bag.
If you stop recharging or discharging part way through, make sure to remove the battery pack before
unplugging the adapter’s AC cord.
Remove the battery pack from the adapter immediately after discharging.
To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.
Make sure you unplug the DC cord before charging or discharging the battery pack.
A blinking CHG. indicator means that the battery pack has become hot. Wait until it cools down to
continue.
The CHG. indicator may not light properly with a brand new battery pack, or with one that’s been stored
for an extended period. In this case, remove and reattach the battery pack and recharge it. The CHG.
indicator should light during recharging. If not, contact your nearest JVC dealer.
USING A CAR BATTERY
Use the optional Car Battery Cord or Car Battery
Charger/Adapter (connect as shown in the
illustration to the left).
NOTES:
When using the car battery, leave the engine
idling.
The optional Car Battery Charger (BH-V3E) can
also be used to charge the battery pack.
When using the optional Car Battery Charger or
Car Battery Cord (AP-V7E), refer to the respective
instruction booklet.
USING AC POWER
Use the AC Power Adapter (connect as shown in
the illustration to the left).
NOTE:
The supplied AC Power Adapter/Charger features
automatic voltage selection in the AC range from
110 V to 240 V.
Charge marker
AC Power
Adapter/Charger
AA-V11EK (provided)
To cars
cigarette
lighter
socket
Car Battery Charger/Adapter
BH-V3E (optional)
DC cord
Car Battery Cord
AP-V7E (optional)
To AC outlet
To
DC OUT
terminal
To
DC IN
Jack
8
GETTING STARTED (cont.)
Clock Battery (Lithium) Insertion/Removal
This battery is necessary for clock operation and to
perform date/time settings.
SWITCH OFF POWER
1
Switch off the unit’s power and remove the power
supply unit.
OPEN COVER
2
Open the clock battery compartment cover while
pressing the release tab.
REMOVE BATTERY (when replacing)
3
Insert a pointed, non-metallic object between the
battery and the compartment (
A
) and pull the
battery out.
INSERT BATTERY
4
Ensuring the plus (+) side is up, insert the CR2025
lithium battery and push it in.
CLOSE COVER
5
Close the compartment cover until it clicks in place.
NOTE:
See “SAFETY PRECAUTIONS”(
Z
pg. 2) for information
on safe handling of lithium batteries.
Viewfinder Adjustment
POSITION VIEWFINDER
1
Adjust the viewfinder manually for best viewability
(see illustration at left).
SELECT MODE
2
Set the power switch to CAMERA.
ADJUST DIOPTER
3
Turn the diopter adjustment control until the
indications in the viewfinder are clearly focused.
A
Set POWER to “CAMERA”.
3
1
2
9
Tele Macro OFF
Gain Up AGC
Color Filter NOR.
Tape Length T30
Title
Sub Menu
Shift Zoom OFF
Set
Cancel
1.1.00 10:45
Date/Time
Date/Time Setting
SELECT MODE
1
Set the Power switch to “CAMERA”, and the
Shooting Mode selector to “PRESET”.
ACCESS MAIN MENU SCREEN
2
Press MENU.
SELECT FUNCTION
3
Press to move the highlight bar down to “Date/
Time”, then press NEAR. The Set Date And Time
screen appears.
SET DATE/TIME
4
Press FAR or NEAR until the item you want to set
begins blinking, then press + or to until the correct
setting appears.
If you decide you want to return the date and time
to the previous settings, press FAR or NEAR to
move the highlight bar to “Cancel”, then press
MENU.
If you’re satisfied with the settings, go on to step 5.
START CLOCK OPERATION
5
Once you’ve set the day, month, year and time,
press FAR or NEAR until “Set” begins to blink, then
press MENU. The Main Menu screen reappears.
CLOSE MAIN MENU
6
Press MENU.
NOTES:
To display the date and time in the viewfinder and on a
connected TV, see “Date/Time Insert” (
Z
pg. 18).
If, in step 4, you input an invalid date (30. 2., 31. 6.,
etc.) and perform step 5, “Input Error” appears blinking
at the bottom of the screen. Press +, , FAR or NEAR to
input the correct number.
+
NEAR
FAR
Shooting mode selector
MENU
Set POWER to
“CAMERA”.
Main Menu
Screen
Set Time and
Date Screen
Date
Day/Month/Year
Time
24-hour indication
10
Tele Macro OFF
Gain Up AGC
Color Filter NOR.
Title
Sub Menu
Date/Time
Shift Zoom OFF
Tape Length T45
T30
T45
T60
GETTING STARTED (cont.)
Tape Length Setting
SELECT MODE
1
Set the Power switch to “CAMERA”, and the
Shooting Mode selector to “PRESET”.
ACCESS MAIN MENU SCREEN
2
Press MENU.
SELECT FUNCTION
3
Press + or – to move the highlight bar to “Tape
Length”.
SET TAPE LENGTH
4
Press FAR or NEAR to cycle through until the correct
setting appears (depending on the tape used). T30 =
30 minutes of recording time, T45 = 45 min. and
T60 = 60 min. (when recording in SP mode).
CLOSE MAIN MENU
5
Press MENU.
NOTES:
The tape remaining time (
Z
pg. 14) displayed in the
viewfinder is correct only if the correct tape length has
been selected.
When using a 60-minute tape, the tape ramaining time
displayed will not be accurate.
Main Menu
Screen
+
FAR
NEAR
MENU
Shooting mode selector
11
SP
LP SP
Recording Mode Setting
1
Pressing SP/LP alternates the setting between SP
(standard play-provides higher picture and sound
quality, better for dubbing) and LP (Long Play-more
economical, recording at 1/2 the speed of SP).
NOTE:
If the recording mode is switched during recording, the
playback picture will be blurred at the switching point.
Loading/Unloading A Cassette
OPEN CASSETTE HOLDER
1
Slide EJECT until the holder opens. Do not use force
to open.
INSERT/REMOVE CASSETTE
2
Make sure the label is facing outward.
CLOSE CASSETTE HOLDER
3
Press PUSH and make sure the holder is closed and
locked.
NOTES:
A cassette holder can’t be opened unless a power
supply is attached.
Make sure that the tape is not slack when loading the
cassette. If there is any slack, turn the gear on the
cassette in the direction of the arrow to take up the
slack.
Make sure the Erase Protection tab is present. If not,
cover the hole with adhesive tape. (Some cassettes
have sliding tabs – in this case, check the tab’s
position.)
SP/LP
Gear
Turn to take up
slack.
Erase Protection
12
2
3
1
2
1
GETTING STARTED (cont.)
Grip Adjustment
EXPAND LOOP
1
Separate the Velcro strip.
INSERT HAND
2
Pass your right hand through the loop and grasp the
grip.
ADJUST STRAP LENGTH
3
Adjust so your thumb and fingers can easily operate
the Recording Start/Stop button and Power Zoom
lever. Refasten the Velcro strip.
Shoulder Strap Attachment
ATTACH STRAP
1
Following the illustration at left, thread the strap
through the top of the eyelet 1, then fold it back
and thread it through the keeper 2, and then
through the buckle 3. Repeat the procedure to
attach the other end of the strap to the other eyelet,
making sure the strap isn’t twisted.
ADJUST LENGTH
2
Adjust as shown in the illustration at left 1, then
slide both keepers snug against the eyelets to
prevent slipping 2.
Tripod Mounting
ALIGN AND TIGHTEN
1
Align the screw and camera direction stud on the
tripod with the camera’s mounting socket and stud
hole. Then tighten the screw.
Recording Start/Stop button
13
1
2
3
4
5
6
7
8
9
0
!
@
$
#
%
^
&
*
10°
5m
10°
30°
30°
Installing The Battery
PULL OUT BATTERY HOLDER
1
Pull out while sliding the lock hole.
INSERT BATTERY
2
Making sure the plus (+) side is up, insert the lithium battery
(CR2025) into the battery holder.
REPLACE BATTERY HOLDER
3
Insert the battery holder into the remote control unit, and
push the holder until it clicks into place.
NOTE:
Read the caution concerning lithium batteries (
Z
pg. 2).
BUTTONS
FUNCTIONS
With the camcorder’s power switch With the camcorders power switch set
set to “CAMERA”. to “PLAY”.
1 PAUSE IN Connector —(Z P. 40)
2 Infrared beam
Transmits the beam signal.
transmitting window
3 MBR SET Button —(Z P. 39)
4 INT. TIME Button Self-Timer/Time-Lapse (Z pg. 32, 33)
5 REC TIME Button Animation/Time-Lapse (Z pg. 33)
6 FF Button Retake (forward) (Z pg. 16) FF/FF Shuttle Search (Z pg. 36)
7 REW Button Retake (rewind)/Quick Review (Z pg. 15) Rew/Rew Shuttle Search (Z pg. 36)
8 PAUSE Button Pause/Play (Z pg. 36)
9 PLAY Button Playback start (Z pg. 36)
0 SNAPSHOT Button
Functions same as the SNAPSHOT
Button on the camcorder (Z pg. 19).
! START/STOP Button
Functions same as the Recording Start/Stop
Button on the camcorder.
@ VISS Button Index Code marking (Z pg. 16)
# ZOOM (T/W) Buttons Zoom in and out (Z pg. 15)
$ VCR CTL Button —(Z P. 39)
% A.DUB Button Audio dubbing (Z pg. 43)
^ STOP Button Stop (Z pg. 36)
& INSERT Button Insert Editing (Z pg. 42)
* R.A.EDIT Buttons —(Z P. 40)
The transmitted beam may not be effective or may
cause incorrect operation when the infrared beam
sensor window is directly exposed to sunlight or
powerful lighting.
Infrared beam
effective area
Using The RM-V706U Remote Control Unit
The RM-V706U full-function MBR (Multi-Brand Remote) can operate this camcorder from a distance as well as the basic
operations (PLAY, STOP, PAUSE, FF, and REW) of your VCR. This remote control unit is useful when dubbing from the
camcorder to your VCR, and it makes additional recording functions possible.
Lock hole
Infrared beam
sensor window
14
25min
120min 119min
3min
2min (Blinking)
1min (Blinking)
0min (Blinking)
* min.....(Now calculating)
RECORDING
Basic Recording
NOTE:
You should already have performed the procedures listed
below. If not, do so before continuing.
Power (
Z
pg. 6)
Tape Length (
Z
pg. 10)
Recording Mode Setting (
Z
pg. 11)
Grip Adjustment (
Z
pg. 12)
LOAD A CASSETTE
1
Slide EJECT to open the cassette holder, then insert
the cassette with the label facing out. Press PUSH to
ensure the holder is closed and locked.
ENTER RECORD–STANDBY MODE
2
Slide the LENS COVER open/close switch to open
the lens cover, then set the power switch to
“CAMERA”.
The power indicator lights and the camcorder
enters the Record–Standby Mode.
The scene you’re aimed at appears on the
viewfinder screen, with the word “PAUSE”
superimposed upon it.
START SHOOTING
3
Press the RECORDING START/STOP button.
•The tally lamp lights while recording is in progress,
and “
REC
” appears in the viewfinder.
If you want to turn the tally lamp off, see page 29.
STOP RECORDING
4
Press the RECORDING START/STOP button again to
stop recording.
The camcorder re-enters the Record-Standby
mode.
LENS COVER
SWITCH
POWER
Start/Stop
The power indicator
Tape remaining time indicator
Tally lamp
NOTES:
A cassette holder can’t be opened unless a power supply is attached.
There may be a delay after you slide EJECT until the holder opens. Do not use force.
The tape’s remaining time is displayed in the viewfinder as shown.
The indicated remaining time is approximate.
The time required to calculate the remaining tape length, and the accuracy of the calculation, may vary
according to the type of tape used.
The tape remaining time displayed in the viewfinder is correct only if the correct tape length has been
selected (
Z
pg. 10).
When using a 60-minute tape, the tape ramaining time displayed will not be accurate.
“TAPE END” appears when the tape reaches its end, and the power goes off automatically if left in this
condition for 5 minutes. “TAPE END” also appears when a cassette whose tape is already at its end is
loaded.
If the Record–Standby mode continues for 5 minutes without performing Zoom or any other operations,
the camcorders power shuts off automatically. Set the Power switch to “POWER OFF”, and then back to
“CAMERA” to turn the camcorder on again.
If you’re recording on a cassette from the middle, use the RETAKE function (
Z
pg. 16) to find the end of
the last recording so you don’t erase any of it.
The LENS COVER warning blinks for about 8 seconds when the camcorder is turned on, when the cover is
closed.
15
W
T
W
T
W
T
W
T
W
T
Tele Macro OFF
Gain Up AGC
Color Filter NOR.
Tape Length T45
Title
Date/Time
Sub Menu
Shift Zoom l50x
Zoom-in
Zoom-out
RECORDING
Basic Features
FEATURE: Zooming
PURPOSE: To produce the zoom in/out effect, or
an instantaneous change in image
magnification.
OPERATION: 28X Hyper zoom
Digital circuitry doubles the
maximum 14x magnification offered
by optical zoom.
1) To zoom in, slide the Zoom Lever
toward “T”.
2) To zoom out, slide toward “W”.
Shift Zoom
By digitally processing and
magnifying images, zooming is
possible from 5 – 14 times the
optical zoom limit, to a maximum of
140x magnification.
1) Set the Shooting Mode Selector to
“PRESET” and press MENU to
access the Main Menu screen.
2) Press + or to move the highlight
bar to “Shift Zoom.”
3) Press FAR or NEAR to set the
magnification. “50x” magnifies
wide-angle images to
approximately 3.6 times the
original size, and enables zooming
in the 18x – 50x range. “140x”
magnifies wide-angle images to
approximately 10 times the
original size, and allows zooming
from 50x to 140x. To disable Shift
Zoom, set it to “OFF”.
4) Press MENU to close the Main
Menu screen.
NOTES:
During Hyper Zoom, the speed
increases the further you slide the
Zoom Lever.
Focusing may be come unstable
during Hyper Zoom. In this case,
set the zoom while in Record –
Standby, set manual focus or Focus
Lock (
Z
pg. 22, 23), then zoom in
or out in Record mode.
The Zoom Level Indicator (
5
) only
moves during optical zoom. Once
the indicator reaches “T”, all
magnification from that point is
through digital processing.
During digital image processing,
the quality of the image may suffer.
FEATURE: Quick Review
PURPOSE: To check the end of the last
recording.
OPERATION: 1) Press “
” and release quickly
during the Record–Standby mode.
Tape is rewound for about 2
seconds and played back automati-
cally, then pauses in Record–
Standby mode for the next shot.
NOTE:
Distortion may occur at start of playback.
This is normal.
Zoom indicator bar
Zoom level
indicator
Main Menu
screen
FAR
+
Power zoom lever
MENU
NEAR
Shooting mode
selector
16
RECORDING
Basic Features (cont.)
START/STOP
VISS
FEATURE: Index Code Marking
PURPOSE: To give you automatic access to any
selected point on a recording. Auto
Marking and Manual Marking are
available.
OPERATION:
Auto Marking
An index code is marked to start the
first recording after a cassette is
inserted, as long as the Power switch
is set to “CAMERA”.
Manual Marking
1) Press VISS once to place the index
code. INDEX blinks in the
viewfinder during marking.
NOTE:
If VISS is pressed during
Record–Standby mode, the mark is
placed where RECORDING
START/STOP is pressed.
FEATURE: Retake
PURPOSE: To re-record certain segments.
OPERATION: 1) Make sure the camcorder is in the
Record–Standby mode.
2) Press either RETAKE button to
reach the start point for new
recording.
3) Press RECORDING START/STOP
to start recording.
NOTE:
Noise may appear during Retake.
This is normal.
FEATURE: Auto Pause System
PURPOSE: To automatically stop recording
when the camcorder is pointed
down, preventing accidental
recordings of the ground, your feet,
etc.
OPERATION: 1) Set AUTO PAUSE to “ON”. When
the camcorder is tilted down by a
large degree from its horizontal
position during recording, the
Record-Standby mode is
automatically engaged. “AUTO
PAUSE” appears in the viewfinder.
NOTES:
The Auto Pause System is also
effective when the camcorder is
pointed up, or is positioned upside
down.
Auto Pause also works when the
camcorder is twisted by a large
degree to the left or right.
When you want to shoot in any of
the aforementioned positions,
make sure you set AUTO PAUSE to
“OFF”.
AUTO PAUSE
Down
Record-Standby
Record
Record-Standby
Record-Standby
Normal Upside down
Up
RM-V706U (provided)
RETAKE
17
Video Light
When natural lighting is too dim, you can brighten the
scene by using the built-in video light.
SET VIDEO LIGHT
1
Set the LIGHT ON/AUTO/OFF as required.
ON : Always keeps the light on as long as the
camcorder is turned on.
AUTO : Automatically turns on the light when the
camcorder senses insufficient lighting on
the subject.
OFF : Turns off the light.
The video light can be used with the camcorders
power on.
It is recommended to set the white balance
(Z pg. 21) to indoor mode ( ) when you use the
video light.
When not using the video light, turn it off to save
battery power.
NOTES:
Even if the battery indicator ( ) does not blink in the
viewfinder, if the battery pack’s charge is low, the
camcorder may turn off automatically when you turn
on the video light, or when you start recording with the
video light turned on.
When the LIGHT ON/AUTO/OFF switch is set to
“AUTO”:
Depending on the lighting conditions, the video light
may keep turning on and off. In this case, manually
switch the light on or off using the LIGHT ON/
AUTO/OFF switch.
While the Sports or High-Speed Shutter mode
(
Z
pg. 25) is engaged, the light is likely to stay on.
While the Twilight mode (
Z
pg. 25) is engaged, the
light will not activate.
DANGER
The video light become extremely hot. Do not
touch it either while in operation or soon after
turning it off, otherwise serious injury may result.
Do not place the camcorder into the carrying case
immediately after using the video light, since it
remains extremely hot.
When operating, keep a distance of about 30 cm.
between the video light and people or objects.
Do not use near flammable or explosive materials.
It is recommended that you consult your nearest
JVC dealer for replacing the video light.
LIGHT ON/AUTO/OFF
18
Date/Time Insert
This feature allows you to display the date and time in your
viewfinder and on a connected TV.
NOTE:
You should already have performed the Date/Time
Setting procedure (
Z
pg. 9). If you haven’t, do so before
continuing.
DISPLAY
CHOOSE DISPLAY MODE
1
Press DISPLAY during Record–Standby to cycle
through the available modes as shown in the
illustration at left.
NOTES:
The selected display can be recorded.
If you don’t want to record the display, select Date-off
mode before shooting.
If you want to delete the display during shooting, press
DISPLAY.
If you want to call back a deleted display, engage the
Record-Standby mode and then press DISPLAY to
select the desired display mode.
RECORDING
Advanced Features
Date display
Time display
Date/Time display
Date/Time-off mode
25.12.96
15:28:43
Date display
25.12. 96
25. 12. 96
15:28:43
Date/Time display
Time display
15:28:43
DISPLAY
19
Multi4
Pin-upFrame
Full
Multi 9Multi 4
AB
CD
AB
DE
GH
C
F
I
Record multiple images in one scene
(4 or 9 at a time). The images appear and are
stored in this order: A, B, C, D (E, F, G, H, I for
Multi-Analyzer 9). In the Motor Drive mode,
after “I”, the next image recorded is “A”, and
the cycle is repeated.
Multi-Analyzer 4/Multi-Analyzer 9
Full
A still image that occupies
the entire image field is
recorded.
Frame
A still image with a white
border is recorded.
Pin-Up
A still image on a blue
background. The image is
bordered in white and a
shadow effect is added to
give it a more dimensional
feel.
Snapshot
This interesting feature lets you record several types of
digital still images that look, and sound, like photo-
graphs. It’s a great way to spice up footage of events such
as parties, weddings and graduations.
SELECT SNAPSHOT MODE
1
Press SNAP SHOT MODE to cycle through the
modes as shown in the illustration at left. Once the
desired mode appears, it is selected and activated,
and its indicator appears, within 2 seconds.
PERFORM SNAPSHOT
RECORDING
2
Press SNAP SHOT.
If you press during recording . . .
.... a still image is displayed and recorded in the
selected mode, then the camcorder resumes
normal recording. In the Full and Frame modes,
the new image comes in gradually overall. In
the Pin-Up and Multi-Analyzer modes, the new
image comes in gradually from the centre.
If you press during RECORD–STANDBY . . .
.... a still image is displayed and recorded in the
selected mode, then the camcorder re-enters the
Record–Standby mode.
Motor Drive Function
SELECT SNAPSHOT MODE
1
Select as in step 1 above.
ACTIVATE MOTOR DRIVE
2
During Snapshot recording, press and hold down
SNAP SHOT. You can take rapid snapshots with an
interval of approximately 0.7 seconds between stills.
NOTES:
The Date/Time display will disappear during Snapshot
recording.
The Motor Drive function cannot be activated using the
SNAP SHOT button on the RM-V706U remote control
unit (provided).
When Multi-Analyzer is activated, the shutter sound
may not match the appearance of the images.
SNAP SHOT
SNAP SHOT MODE
20
+
02
+
06
06
RECORDING
Advanced Features (cont.)
Digital Image Stabilizer
This feature compensates for unstable images caused by
camera-shake, particularly noticeable at high
magnification.
ACTIVATE D. I. STABILIZER
1
Press D.I.STABILIZER. “ ” appears in the viewfinder.
To switch off the Digital Image Stabilizer, press
D.I.STABILIZER. The indicator disappears.
NOTES:
Accurate stabilization may not be possible if hand
shake is excessive, or under the following conditions:
When shooting subjects with vertical or horizontal
stripes
When shooting dark or dim subjects
When shooting subjects with excessive backlighting
When shooting scenes with movement in various
directions
When shooting scenes with low-contrast
backgrounds
When the Slow Shutter function is activated
(
Z
pg. 25), the Digital Image Stabilizer (DIS) cannot
be used. If you try to activate this function while DIS is
engaged, “ ” blinks, telling you that DIS has been
deactivated.
Switch off DIS when recording with the camcorder on
a tripod.
Exposure Control
This feature automatically adjusts the iris for the best
available picture quality, but you can override and make
the adjustment manually.
SELECT SHOOTING MODE
1
Set the Shooting Mode selector to “PRESET”.
BRIGHTEN IMAGE
2
Press + (maximum +06). The Exposure level
indicator appears in the viewfinder.
OR . . .
DARKEN IMAGE
Press (maximum –06). The Exposure level
indicator appears in the viewfinder.
When you want to return to the factory setting . . .
RESTORE INITIAL SETTING
3
Press + andsimultaneously. The standard setting is
immediately restored and the Exposure level
indicator disappears.
To brighten the image
To darken the image
+
Shooting Mode Selector
D.I. STABILIZER
Viewfinder
D.I.S. Indicator
Exposure Level Indicator
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

JVC GR-AX860 User manual

Category
Camcorders
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI