VMAC – Vehicle Mounted Air Compressors
Toll Free: 1-888-241-2289 Local: 1-250-740-3200
Fax: 1-250-740-3201
1
A500013
Tank Installation Instructions
RAPTAIR MULTIFUNCTION Diesel Driven Compressor
Important Information
The information in this manual is intended for certified VMAC installers who have been trained in
installation procedures and for people with mechanical trade certification who have the tools and
equipment to properly and safely perform the installation. Do not attempt this installation if you do
not have the appropriate mechanical training, knowledge and experience.
Follow all safety precautions for mechanical work. If you have difficulty with the installation,
contact VMAC.
To order parts, contact your VMAC dealer. Your dealer will ask for the VMAC serial number, part
number, description and quantity. To locate your nearest dealer, call 1-888-241-2289, or see our
website www.vmacair.com and click ‘Find a Dealer’.
Notice: Manuals and products are subject to change without notice
Document #1900991
Version
Revision Details
Revised by/date
Checked by/date
Reviewed by/date
Implemented
A
ECN 14-001 :Release
MH – 15Jan2014
PD 31 Jan 2014
RD 31 Jan 2014
31 Jan 2014
A
Corr: update note on newer gen panels
MSP 16 Aug 2016
DB 16 Aug 2016
JKR 19 Aug 2016
19 Aug 2016
Copyright 2016
All trademarks used in this manual are the property of the respective copyright holder.
The contents of this manual may not be reproduced in any form without the express written permission of VMAC, 1333 Kipp Road, Nanaimo, BC
V9X 1R3. Printed in Canada
VMAC – Vehicle Mounted Air Compressors
Toll Free: 1-888-241-2289 Local: 1-250-740-3200
Fax: 1-250-740-3201
2
Fuel Tank Installation
(NOTE: The generator panel on newer units are equipped with mounting holes and PEM
nuts.)
1. Mark and drill (4X) Mounting holes on generator side panel (This can be done with panel in
place or removed)
Holes can be marked by one of the two following ways,
Using the measurements supplied on this drawing
Align the top and right side of the fuel tank with the top and radiator side panels
of the Raptair-MF
2. Loosely install the fuel tank with supplied fasteners and align square with panels before
tightening.
3. Connect the supply and return fuel lines from the Raptair-MF to the fuel tank using the
supplied hose clamps. (The supply line is 5/16” and the return line is 3/16”)
4. Connect the fuel level sensor to the Raptair-MF wiring harness.
5. Strap tie wires and hoses together after assembly.
G E N E R A T O R S I D E P A N E L
MO U N T I N G L O C A T I O N
( N O T E : O N L Y G E N E R A T O R S I D E P A N E L S H O W N
I N T H I S V I E W )
E N S U R E A I R F L O W I S N O T
B L O C K E D F R O M T H I S V E N T
D I A .3 7 5 ( 3 / 8 )
( 4 X ) 15 .8 4
1.0 8
3 .3 6
12 .6 0
2 .8 0
22.94
D R I L L
H OL E S
( N U T S T O B E I N S T A L L E D
O N I N S I D E O F P A N E L )
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Vmac S700170 Owner's manual
-
Vmac S700162 Owner's manual
-
Vmac V910022 Installation guide
-
Vmac 3550859 Installation guide
-
Vmac V900084 Installation guide
-
Vmac V900117 Installation guide
-
Vmac S700077 Installation guide
-
Vmac V900094 Installation guide
-
Vmac V900103 Installation guide
-
Vmac V300012 Installation guide
