Pentair Pool TR40 Triton Fiberglass Sand Filter User manual

TRITON®

FIBERGLASS SAND FILTER

MODELS: TR40, TR50, TR60, TR100, TR140, TR100HD,

TR100C, TR140C, TR100C-3, TR140C-3 and TR60 with

CLEARPRO TECHNOLOGY®

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

INSTALLATION AND

USER’S GUIDE

ESPAÑOL 21 FRANÇAIS 45

ENGLISH 1

i

This document is subject to change without notice.

1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000

10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 553-5000

All Pentair trademarks and logos are owned by Pentair or one of its global afﬁliates. Triton® and ClearPro Technology® are trademarks and/

or registered trademarks of Pentair Water Pool and Spa, Inc. and/or its afﬁliated companies in the United States and/ or other countries.

Unless expressly noted, names and brands of third parties that may be used in this document are not used to indicate an afﬁliation or

endorsement between the owners of these names and brands and Pentair Water Pool and Spa, Inc. Those names and brands may be

the trademarks or registered trademarks of those third parties. Because we are continuously improving our products and services, Pentair

reserves the right to change speciﬁcations without prior notice. Pentair is an equal opportunity employer.

P/N 154901 Rev. J 9/26/17

If you have questions about ordering Pentair Aquatic Systems replacement parts, and pool products, please contact:

CUSTOMER SERVICE / TECHNICAL SUPPORT

Customer Service and Technical Support, USA

(8 A.M. to 4:30 P.M. — Eastern/Paciﬁc Times)

Phone: (800) 831-7133

Fax: (800) 284-4151

Web site

Visit www.pentairpool.com or www.staritepool.com for

information about Pentair products.

Sanford, North Carolina (8 A.M. to 4:30 P.M. ET)

Phone: (919) 566-8000

Fax: (919) 566-8920

Moorpark, California (8 A.M. to 4:30 P.M. PT)

Phone: (805) 553-5000 (Ext. 5591)

Fax: (805) 553-5515

TABLE OF CONTENTS

Important Warnings and Safety Precautions ....

Section 1: Introduction

Triton Fiberglass Sand Filters Overview

General Features

Section 2: Installation .........................................

Installing the Filter

How the Filter Works

Installing the Closures

Initial Start-Up

Section 3: Maintenance .......................................

Filter Care

Filter Cleaning

Filter Backwash Procedure

Chemical Cleaning Procedure

Winterizing the Filter

ii

1

2

3

5

6

7

8

9

Section 4: Troubleshooting .................................

Section 5: Replacement Parts ............................

Filter Pressure Drop Curve

Installing Multiple Triton Filter (Tandem Filter

Piping Kits)

Triton II & TR60 ClearPro Replacement Parts

Triton 100HD, 100C & 140C Replacement

Parts

Triton 100C-3 & 140C-3 Replacement Parts

10

12

13

16

18

TRITON® Fiberglass Sand Filter Installation and User’s Guide

ENGLISH

Consumer Information and Safety

The Triton Series Sand Filters are designed and manufactured to provide many years of safe and reliable service when

installed, operated and maintained according to the information in this manual and the installation codes referred to in

later sections. Throughout the manual, safety warnings and cautions are identiﬁed by the “ “ symbol. Be sure to read

and comply with all of the warnings and cautions.

THIS FILTER OPERATES UNDER HIGH PRESSURE

When any part of the circulating system, (e.g., closure, pump, ﬁlter, valve(s), etc.), is serviced, air can

enter the system and become pressurized. Pressurized air can cause the top closure to separate

which can result in severe injury, death, or property damage. To avoid this potential hazard, follow

these instructions:

1. If you are not familiar with your pool ﬁltering system and/or heater:

a. Do NOT attempt to adjust or service without consulting your dealer, or a qualiﬁed pool

technician.

b. Read the entire Installation & User’s Guide before attempting to use, service or adjust the

pool ﬁltering system or heater.

2. Before repositioning valve(s) and before beginning the assembly, disassembly, or any other

service of the circulating system: (A) Turn the pump OFF and shut OFF any automatic

controls to ensure the system is NOT inadvertently started during the servicing; (B) open the

manual air bleeder valve; (C) wait until all pressure is relieved.

3. Whenever installing the ﬁlter closure FOLLOW THE FILTER CLOSURE WARNINGS EXACTLY.

4. Once service on the circulating system is complete FOLLOW INITIAL START-UP

INSTRUCTIONS EXACTLY.

5. Maintain circulation system properly. Replace worn or damaged parts immediately, (e.g.,

closure, pressure gauge, valve(s), o-rings, etc).

6. Be sure that the ﬁlter is properly mounted and positioned according to instructions provided.

IMPORTANT WARNING AND SAFETY INSTRUCTIONS

IMPORTANT NOTICE:

This guide provides installation and operation instructions for the Triton® Series Fiberglass

Sand Filters. Consult Pentair Water Pool and Spa with any questions regarding this

equipment.

Attention Installer: This guide contains important information about the installation, operation and safe

usage of this product. This information should be given to the owner and/or operator of this equipment after

installation or left on or near the ﬁlter.

Attention User: This manual contains important information that will help you in operating and maintaining

this ﬁlter. Please retain it for future reference.

Before installing this product, read and follow all warning notices and instructions which are

included. Failure to follow safety warnings and instructions can result in severe injury, death,

or property damage. Call (800) 831-7133 for additional free copies of these instructions.

ii

TRITON® Fiberglass Sand Filter Installation and User’s Guide

IMPORTANT WARNING AND SAFETY INSTRUCTIONS

This ﬁlter must be installed by a licensed or certiﬁed electrician or a qualiﬁed pool serviceman

in accordance with the National Electrical Code and all applicable local codes and ordinances.

Improper installation could result in death or serious injury to pool users, installers, or others and

may also cause damage to property.

Always disconnect power to the pool circulating system at the circuit breaker before servicing the

ﬁlter. Ensure that the disconnected circuit is locked out or properly tagged so that it cannot be

switched on while you are working on the ﬁlter. Failure to do so could result in serious injury or

death to serviceman, pool users or others due to electric shock.

Do not operate the ﬁlter until you have read and understand clearly all the operating

instructions and warning messages for all equipment that is a part of the pool circulating

system. The following instructions are intended as a guide for initially operating the ﬁlter

in a general pool installation. Failure to follow all operating instructions and warning

messages can result in property damage or severe personal injury or death.

To reduce the risk of injury, do not permit children to use this product unless they are

closely supervised at all times.

Due to the potential risk that can be involved it is recommended that the pressure test be

kept to the minimum time required by the local code. Do not allow people to work around

the system when the circulation system is under pressure test. Post appropriate warning

signs and establish a barrier around the pressurized equipment. If the equipment is located

in an equipment room, lock the door and post a warning sign.

Never attempt to adjust any closures or lids or attempt to remove or tighten bolts when the

system is pressurized. These actions can cause the closure to separate and could cause

severe personal injury or death if they were to strike a person.

Never exceed the maximum operating pressure of the system components. Exceeding

these limits could result in a component failing under pressure. This instantaneous release

of energy can cause the closure to separate and could cause severe personal injury or

death if they were to strike a person.

iii

TRITON® Fiberglass Sand Filter Installation and User’s Guide

1

ENGLISH

SECTION 1

INTRODUCTION

Triton® Fiberglass Sand Filters Overview

Triton® II Sand Filters

The Triton II ﬁlter is the result of over 40 years of product evolution and reﬁnement. It has set the industry

standard for effectiveness, efﬁciency, long runs between service, and providing years of dependable,

low maintenance operation.

The Triton II ﬁlter features a special internal design that keeps the sand bed level, ensuring even water

ﬂow, and resulting in the most efﬁcient ﬁltration possible.

The Triton II ﬁlter provides superior ﬁltration performance and delivers a level of dependability and

ease of operation and maintenance for a track record that’s unsurpassed. Every design detail has

been reﬁned to make Triton II the industry standard.

Triton® C and Triton® C-3 Commercial Sand Filters

This ﬁlter series features multiple diverters for increased ﬁltration rates in commercial applications up

to 20 GPM/Sq. Ft.

Triton® HD Side Mount Sand Filters

All the same great performance and features of the original Triton’s with maximum operating pressure

of 75 psi for those special high pressure installations such as single pump in-ﬂoor cleaning systems.

Triton II - Residential

Triton C - Commercial

Triton C-3 - Commercial

Triton HD - Commercial

2

TRITON® Fiberglass Sand Filter Installation and User’s Guide

General Features

Triton® II

• Time-proven internal design ensures that all water receives maximum ﬁltration for crystal clear

results

• A one-piece, ﬁberglass reinforced tank with a UV-resistant coating for years of dependable,

corrosion-resistant service

• Flow system design controls ﬁltration quality and ensures maximum run times between backwashing

to save you time

Triton® C and Triton® C-3

• Maximum Operating Pressure 50 psi

• Full 2 in. drain

• 8 in. opening for easy access to sand bed

• The Triton C-3 features standard 3 in. ﬂange connections

• TR100C & TR140C models are available in black or almond

• TR100C-3 & TR140C-3 models are available in black only

Triton® HD

• Maximum Operating Pressure 75 psi

Additional Features:

• Combination sand and water drain speeds servicing and winterizing

• All internal parts are threaded for ease of maintenance

• Swing-away water diffuser allows instant access to sand and all internal parts

• NSF-Listed

TRITON® Fiberglass Sand Filter Installation and User’s Guide

3

ENGLISH

SECTION 2

INSTALLATION

NOTE: Before installing this product, read and follow all warning notices and instructions starting on page ii.

Installing the Triton® Fiberglass Sand Filter

Only a qualiﬁed service person should install the Triton ﬁlter. This ﬁlter is designed and intended for use

to ﬁlter water.

Introduction

The following general information describes how to install the Triton Fiberglass Sand Filter. This ﬁlter

operates under pressure and if assembled improperly or operated with air in the water circulation

system, the top closure can separate and result in an accident causing property damage or serious

bodily injury. A warning label has been afﬁxed to the top of the ﬁlter and should not be removed. Keep

safety labels in good condition and replace if missing or illegible.

How the Filter Works

The high rate sand ﬁlter is designed to operate for years with a minimum of maintenance and when

installed, operated and maintained in accordance with these instructions, it will provide years of trouble

free operation.

Dirt is collected in the ﬁlter as the water ﬂows through the control valve at the side of the ﬁlter and is

directed into the top bulkhead. Dirty water ﬂows into the diffuser at the top of the tank and is directed

downward into the top surface of the ﬁlter sand bed. The dirt is collected in the sand bed and the clean

water ﬂows through the laterals and lower piping at the bottom of the ﬁlter up into the lower bulkhead.

The ﬂow then goes into the control valve at the side of the ﬁlter. Clean water is returned through the

piping system into the pool.

The pressure will rise and the ﬂow to the pool will be lowered as the dirt is collected in the ﬁlter. Eventually,

the ﬁlter will become so plugged with dirt that it will be necessary to perform the backwash procedure. It

is important to know when to backwash the ﬁlter. Backwashing is discussed further under the subsequent

sections of this guide.

Please note that a ﬁlter removes suspended matter and does not sanitize the pool. The pool water

must be sanitized and the water must be chemically balanced for sparkling clear water. Your ﬁltration

system should be designed to meet your local health codes. As a minimum, you must be sure that

your system will turn over the total volume of water in your pool at least two to four times in a twenty-

four hour period.

Refer to Table 1 for Filter Operation Data.

FILTER MODEL

MODEL

FILTER

AREA

(Sq. Ft.)

Flow Rate

*(GPM)

@20 GPM/FT2

Turnover Capacity (Gallons)

(Based on 20 GPM / Sq. Ft.)*

4 TURNS PER DAY 3 TURNS PER DAY 2.4 TURNS PER DAY 2 TURNS PER DAY

TR40 1.92 38 13,680 18,240 22,800 27,360

TR50 2.46 49 17,640 23,520 29,400 35,280

TR60 3.14 63 22,680 30,240 37,800 45,360

TR60 ClearPro 3.14 63 22,680 30,240 37,800 45,360

TR100 4.91 74 26,640 35,520 44,400 53,280

TR100HD 4.91 74 26,640 35,520 44,400 53,280

TR100C/TR100C-3 4.91 98 35,280 47,040 58,800 70,560

TR140 7.06 106 38,160 50,880 63,600 76,320

TR140C/TR140C-3 7.06 141 50,760 67,680 84,600 101,520

Table 1.

*TR100, TR100HD AND TR140 ARE BASED ON 15 GPM/SQ. FT.

4

TRITON® Fiberglass Sand Filter Installation and User’s Guide

Failure to operate your ﬁlter system or inadequate ﬁltration can cause poor water clarity obstructing

visibility in your pool and can allow diving into or on top of obscured objects which can cause serious

personal injury or drowning.

Clear water is the result of proper ﬁltration as well as proper water chemistry. Pool chemistry is a

specialized area and you should consult your local pool service specialist for speciﬁc details. In general,

proper pool sanitation requires a free chlorine level of 1 to 3 PPM and a pH range of 7.2 to 7.6.

Filters should never be tested or subjected to air or gas under pressure. All gases are compressible

and under pressure create a danger. Severe bodily injury or property damage could occur if the ﬁlter is

subjected to air or gas pressure.

1. Check carton for any evidence of damage due to rough handling in shipment. If carton or any ﬁlter

components are damaged, notify the freight carrier immediately.

2. Carefully remove the accessory package and the ﬁlter tank from the carton.

3. Mount the ﬁlter on a permanent slab, preferably concrete poured in a form or on a platform constructed

of concrete block or brick. DO NOT use sand to level the ﬁlter or for the pump mounting, as it will

wash away.

4. Provide space and lighting for routine maintenance access. Do not mount electrical controls over

the ﬁlter. One needs to be able to stand clear of the ﬁlter when starting the pump. Minimum space

requirements may be found on the large nameplate on the ﬁlter.

5. Position ﬁlter so that the port locations are in the desired ﬁnal positions. Follow valve installation

procedures.

6. If you have a Multiport Valve, assemble the valve to the tank, being sure the o-ring on the valve

ﬁttings are in place and are clean. Use a lubricant, applied lightly, such as silicone grease, Dow

#33, #40 or GE 300 or 623, or similar product on o-rings and o-ring grooves prior to assembly.

7. If you have a two position slide valve, align the valve with the tank so that the handle is toward the

top of the tank, push valve into ports and turn the valve nuts snugly on the tank ﬁttings. It is not

necessary to cinch the valve nuts to the tank ﬁtting beyond hand tightness.

8. The shipping straps used to support the TR100C-3, TR140C and the TR140C-3 multi-diffuser

should be removed before loading sand and gravel in the ﬁlter.

9. Sand speciﬁcations – be certain the proper sand is used as described in Table 2. Before pouring

the sand into the ﬁlter, look inside and check the lower under-drain for broken or loose laterals (or

ﬁngers), which may have been accidentally damaged by rough handling during shipment. Replace

any broken parts if necessary.

NOTE: The free board distance is the most important variable and should be maintained. Sand density

will vary and therefore sand amount is given as a reference.

† Media required to meet NSF requirements.

‡ Pea Gravel to be 1/4” to 1/8” diameter.

* Sand to be No. 20 standard silica (uniformity coefﬁcient not greater than 1.75) .018-.020 in diameter particle size.

Table 2.

"X" FREE BOARD

ALL SAND

or

SAND & GRAVEL

MODEL

FREE BOARD

“X”

ALL SAND*

(POUNDS)

FILTER MEDIA†

(POUNDS)

PEA GRAVEL ‡ SAND

TR40 8 1/4” 175 50 125

TR50 9 3/4” 225 50 175

TR60 10 1/2” 325 50 275

TR60 ClearPro 10 1/2” 325 50 275

TR100 11 1/4” 600 150 450

TR100HD 11 1/4” 600 150 450

TR100C-3 11 1/4” 600 150 450

TR140 13 1/2” 925 275 650

TR140C-3 13 1/2” 925 275 650

TRITON® Fiberglass Sand Filter Installation and User’s Guide

5

ENGLISH

Failure to position the Automatic Air Vent inside of the Closure will allow excessive trapped air to accumulate in

the ﬁlter. Trapped air and the closure not properly closed can cause the closure to seperate and could cause

severe bodily injury and/or property damage.

10. Pivot the diffuser out of the center of the tank on the TR40, 50, 60, TR60 ClearPro, 100 & 140 by

rotating the diffuser assembly counter clockwise. (NOTE: The multi-diffuser assembly should not be

moved on models TR100HD, TR100C, TR100C-3 and TR140C, TR140C-3. After installing the ﬁlter

media as described below, check to make sure the tops on the diffusers are parallel to the top of the

sand bed.) Fill the tank about half full of water. Pour pea gravel ﬁrst (if used) and then the sand into the

top of the ﬁlter at a slow rate so that the impact of the ﬁlter media does not damage the laterals. See

Table 2 for the proper amounts of sand and gravel. Fill ﬁlter to the proper level to maintain freeboard,

as shown in Table 2. Pivot the diffuser assembly back to its vertical position if it was moved. Be certain

the automatic air vent is protruding into the top of the closure as indicated below in Figure 1. Ensure

that the automatic air vent is in the center of the ﬁlter closure. Wash away all sand around the threaded

opening at the top of the tank.

For Threaded Closures

Use care when installing closure. The closure should turn freely in the ﬁlter, if resistance to closure

insertion is felt, then slowly remove the closure by turning counter-clockwise. The starting thread of the

tank and closure must engage properly in order to secure the closure. Do not cross-thread closure.

Failure to install the closure properly can cause the closure to seperate and could cause severe bodily

injury and/or property damage.

For Oval Closures

Use care when installing closure. The closure should be inserted into the tank by placing the small

diameter of the oval closure into the larger diameter of the tank opening. Insert the side of the closure

that does not have the pressure gauge and air bleeder ﬁrst. The closure will need to be inserted at a

30° angle. Once the closure is inside the tank, it can be rotated 90° and lifted up to seal the tank. The

aluminum bridge with load spring can then be placed over the closure bolt and the hand knob tightened

to load the closure properly. The knob should be tightened by hand only. DO NOT USE A WRENCH TO

TIGHTEN THE KNOB. You could damage the tank or closure and cause a failure by using a wrench.

Failure to install the closure properly can cause the closure to seperate and could cause severe bodily

injury or property damage.

NEVER ATTEMPT TO TIGHTEN OR LOOSEN THE CLOSURE WITH THE PUMP RUNNING. Failure

to follow this instruction can result in the closure seperating and causing severe bodily injury or property

damage.

11. Assemble the pressure gauge and bleeder valve to the closure lid. Clean the lid o-ring and lubricate

with silicone grease such as Dow #33, 40 or GE 300, 623 lubricant. Place the closure lid on the ﬁlter

and tighten, making certain the air vent is up inside the dome of the closure.

12. With the plastic wrench, provided with the ﬁlter, tighten the closure as tight as possible using two

hands on the wrench handles. As a minimum, the closure

must be hand tight + 1/4 turn.

13. The oval closure that is used on the TR140C-3 and the

TR100C-3 models will need to be installed as described in

the above warning note for oval closures.

14. Assemble piping and pipe ﬁttings to pump and valve. All piping

must conform to local and state plumbing and sanitary needs.

15. Use sealant compounds on all male connections of pipe

and ﬁttings. Use only pipe compounds suited for plastic pipe.

Support pipe to prevent strains on ﬁlter, pump or valve.

16. Long piping runs and elbows restrict ﬂow. For best efﬁciency,

use the fewest possible number of ﬁttings, and large diameter

pipe (at least 2” for TR100 and TR140, at least 3” for TR100C-3

and TR140C-3).

MANUAL AIR

BLEEDER

VALVEPRESSURE

GAUGE

CLOSURE

TANK

AUTOMATIC

AIR VENT

XX

Figure 1.

6

TRITON® Fiberglass Sand Filter Installation and User’s Guide

Operating at excessive vacuum levels can cause the tank to crack and could cause property damage.

17. When installing backwash lines, it is recommended that a vacuum breaker be installed on installations where

the backwash line length exceeds 40 ft. or the backwash line discharges more than 10 ft. lower than the surface

of the pool. Alternately a vacuum break pit should be provided.

18. A check valve is recommended between the ﬁlter and heater to prevent hot water “back-up” which will damage

the ﬁlter and valve.

19. The maximum operating pressure of the unit is 50 pounds per square inch (psi) and 75 pounds per square inch

(psi) for the Triton HD model (only). Never operate this ﬁlter above these pressures or attach a pump to this ﬁlter

that has more than 50 psi shut off pressure or 75 psi shut off pressure for the Triton HD model (only).

20. Never install a chlorinator upstream of the ﬁlter. Always locate downstream and with a check valve between the

chlorinator and ﬁlter.

21. A positive shut off valve is not recommended at the outlet of the ﬁltering system. If the system is ever run with

such a valve closed, the internal air relief system becomes inoperative and risk of tank separation could exist.

Additionally, running the system with no ﬂow will seriously damage the equipment.

22. Never store pool chemicals within 10 ft. of your pool ﬁlter. Pool chemicals should always be stored in a cool, dry

well ventilated area.

23. The oval closure used on the TR100C-3 and TR140C-3 is designed to provide a vacuum relief mechanism that

protects the tank from vacuum conditions. The closure will allow air to enter the tank if the tank is higher that 8 ft.

above the water level. In these cases, when the ﬁlter restarts after shut down, you may observe air being returned

to the pool in the return ﬁttings. This is not unusual, it is simply the automatic air relief in the ﬁlter removing the

air in the ﬁlter.

Initial Start-up

1. On a new pool, clean the pool before ﬁlling the pool with water. Excessive dirt and large particles can cause

damage to the pump and ﬁlter.

2. Ensure the backwash line is open so that water is free to come from the pool and ﬂow out the backwash line.

Set the valve position as follows:

a. If using a Multiport valve, set valve to backwash position.

b. If using a Two Position Slide Valve, push handle down to backwash position and engage lock by twisting

handle.

3. Check pump strainer pot to be sure it is full of water.

Air entering a ﬁlter and tank closure not installed properly can cause the closure to seperate and could cause severe

bodily injury and/or property damage.

4. Check closure on ﬁlter for tightness.

5. Open the manual air bleeder on the ﬁlter closure. Stand clear of the ﬁlter and start the pump allowing it to prime.

6. Close the air bleeder on the closure when all the air is removed from the ﬁlter and a steady stream of water

emerges.

NOTE: Pool ﬁlter sand is typically pre-washed and should not require extensive backwashing. However, the shipping

process may cause excessive abrasion which could require an extended backwash cycle at initial start-up; continue

to backwash until the backwash water is as clear as the pool water.

To prevent equipment damage and possible injury, always turn the pump off before changing the valve position.

7. Stop the pump. Set the valve position as follows:

a. If using a Multiport valve, set the valve to the ﬁlter position.

b. If using the Two Position Slide Valve, raise the handle to ﬁlter position and engage valve lock by twisting handle.

8. Ensure all suction and pool return lines are open so that water is free to come from the pool and return to the pool.

9. Open the manual air bleeder on the ﬁlter closure. Stand clear of the ﬁlter and start the pump.

10. Close the air bleeder on the ﬁlter closure when all the air is removed from the ﬁlter and a steady stream of water

emerges.

11. The ﬁlter has now started its ﬁltering cycle. You should ensure that water is returning to the pool and take note

of the operating pressure when the ﬁlter is clean.

TRITON® Fiberglass Sand Filter Installation and User’s Guide

7

ENGLISH

SECTION 3

MAINTENANCE

This section describes how to maintain your Triton® Fiberglass Sand Filter.

Filter Care

The ﬁlter is a very important part of the pool equipment and installation. Proper care and maintenance

will add many years of service and enjoyment to the pool. Follow these suggestions for long trouble-

free operations:

1. To clean the exterior of the ﬁlter of dust and dirt, wash with a mild detergent and water then hose

off. Do not use solvents.

2. If internal maintenance is required, sand may be removed by removing the sand drain from the bottom

of the ﬁlter and ﬂushing with a garden hose. Pentair Sand Vacuum P/N 542090 may also be used.

3. If after a number of years, the ﬁlter tank appears foggy in color or rough in texture, the tank surface

can be painted. We recommend the use of a Quick Dry Spray Enamel. Do NOT paint the valve.

Always visually inspect ﬁlter components during normal servicing to ensure structural safety. Replace any

item which is cracked, deformed or otherwise visually defective. Defective ﬁlter components can allow

the ﬁlter top or attachments to separate and could cause severe bodily injury or property damage.

4. The ﬁlter closure on your Triton Sand Filter was manufactured with high quality corrosion resistant

materials. This part should be carefully inspected whenever servicing your ﬁlter. If excessive leakage

is noted coming from the closure/tank interface, the closure and o-ring should be carefully inspected

and replaced if any signs of deterioration exist.

5. Your ﬁlter is a pressure vessel and should never be serviced while under pressure. Always relieve

tank pressure and open air bleeder on the ﬁlter closure before attempting to service your ﬁlter.

6. When restarting your ﬁlter, always open the manual air bleeder on the ﬁlter closure and stand clear

of the ﬁlter.

Cleaning Frequency

1. The ﬁlter on a new pool should be backwashed, and cleaned after approximately 48 hours of

operation to clean out plaster dust and/or construction debris.

2. There are three different ways to identify when the ﬁlter needs backwashing.

a. The most accurate indicator on pool systems with a ﬂow meter is to backwash when the

ﬂow decreases 30% from the original (clean ﬁlter) ﬂow. For example, if the original ﬂow was

60 GPM, the ﬁlter should be backwashed when the ﬂow is reduced by about 20 GPM (or

30%) to 40 GPM.

b. A more subjective and less accurate indicator is to observe the amount of water ﬂowing

from the ﬂow directionals located in the wall of the pool. The ﬁlter should be backwashed

once it is detected that the ﬂow has been reduced by about 30%.

c. The most commonly used but less accurate indicator is to backwash when the ﬁlter gauge

reading increases 10 PSI over the initial (clean ﬁlter) reading.

3. It is important not to backwash the ﬁlter solely on a timed basis such as every three days. It is

also important to note that backwashing too frequently actually causes poor ﬁltration. Factors like

weather conditions, heavy rains, dust or pollen, and water temperature all affect the frequency of

backwash. As you use your pool, you will become aware of these inﬂuences.

4. If at any time the starting pressure after backwashing the ﬁlter indicates 4 to 6 PSI higher than

normal starting pressure, it is time to perform a chemical cleaning procedure.

8

TRITON® Fiberglass Sand Filter Installation and User’s Guide

Filter Backwash Procedure

To prevent equipment damage and possible injury, always turn off pump before changing valve positions.

1. Stop the pump.

2. Ensure that the suction and backwash lines are open so that water is free to come from the pool

and ﬂow out the backwash line. Set control valve position as follows:

a. If using a Multiport Valve, set valve to backwash position.

b. If using a Two Position Slide Valve, push handle down to backwash position and engage lock

by twisting handle.

3. Stand clear of the ﬁlter and start pump.

4. Backwash ﬁlter for approximately 3 to 5 minutes or until backwash water is clean.

5. Stop the pump.

a. If using a Multiport Valve, set valve to rinse position and continue with remaining steps.

b. If using a Two Position Slide Valve, skip to step 8.

6. Stand clear of the ﬁlter and start pump.

7. Rinse ﬁlter for approximately 30 seconds.

8. Stop the pump and set valve as follows:

a. If using a Multiport Valve, set valve to ﬁlter position.

b. If using a Two Position Slide Valve, raise handle to ﬁlter position and engage valve lock by

twisting handle.

9. Ensure that pool return line is open so that water may freely ﬂow from the pool back to the pool.

10. Open manual air bleeder on Triton closure. Stand clear of ﬁlter and start pump.

11. Close manual air bleeder of the closure when all the air is removed and a steady stream of water

emerges from the bleeder.

12. The ﬁlter has now started its ﬁltering cycle. You should ensure that water is returning to the pool

and take note of the ﬁlter pressure.

13. The ﬁlter pressure, in the above Step 12, should not exceed the pressure originally observed on

the ﬁlter when it was initially started. If after backwashing, the pressure is 4 to 6 PSI above the

start condition, it will be necessary to chemically clean the sand bed.

TRITON® Fiberglass Sand Filter Installation and User’s Guide

9

ENGLISH

Chemical Cleaning Procedure

1. It is recommended that an approved cleaner be used. Please contact your local pool chemical

supplier or retail store for the proper cleaner.

These cleaners will remove oils, scale and rust from the sand bed in one cleaning operation.

2. Mix a solution following the manufacturers instructions on the label.

3. Backwash the ﬁlter as outlined on page 8.

4. If the ﬁlter is below pool level, shut off the pump and close appropriate valving to prevent draining

the pool.

5. Shut off pump, open ﬁlter drain and let ﬁlter drain. Place valve in backwash position.

6. After ﬁlter has drained, close ﬁlter drain and remove the pump strainer pot lid.

7. Ensure that the backwash lines are open.

8. Turn the pump on and slowly pour the cleaning solution into the pump strainer with the pump

running.

9. Continue adding solution until the sand bed is saturated with cleaning solution. Replace lid on

pump.

10. Shut off the pump and leave ﬁlter in backwash position. Allow ﬁlter to stand overnight (12 hours).

11. Replace the pump lid and follow backwash procedures on page 8.

12. Do not allow the cleaning solution to get into the pool.

Winterizing your Filter

1. In areas that have freezing winter temperatures, protect the pool equipment by backwashing the

ﬁlter.

2. After backwashing, shut the pump off, open the manual air bleeder on the closure and adjust the

valve as follow:

a. On the Multiport Valves, move the handle of the valve to the Winterize Position (*).

b. On the Two Position Slide Valve, if possible, remove the valve piston assembly; clean,

lubricate and store in a dry location for the winter.

*NOTE: The Multiport valve should be left in the winterize position during shutdown season so the

valve diverter has no pressure on the rubber seal.

3. On the TR40, 50, 60, and TR60 ClearPro, remove the wing-type plug on the bottom of the ﬁlter.

On the TR100, TR100HD, TR100C, TR100C-3, and TR140, TR140C, TR140C-3, remove the 1½”

drain plug cap. The ﬁlter will drain very slowly, and therefore, it is recommended that the drain plug

be left out.

4. Drain all appropriate system piping.

5. We recommend covering the equipment with a tarpaulin or plastic sheet to inhibit deterioration

from weather. Do NOT wrap pump motor with plastic.

10

TRITON® Fiberglass Sand Filter Installation and User’s Guide

SECTION 4

TROUBLESHOOTING

Use the following troubleshooting information to resolve possible problems with your Triton® Filter.

THIS FILTER OPERATES UNDER HIGH PRESSURE

When any part of the circulating system, (e.g., closure, pump, ﬁlter, valve(s), etc.), is serviced, air can enter

the system and become pressurized. Pressurized air can cause the top closure to separate which can

result in severe injury, death, or property damage. To avoid this potential hazard, follow these instructions:

1. If you are not familiar with your pool ﬁltering system and/or heater:

a. Do NOT attempt to adjust or service without consulting your dealer, or a qualiﬁed pool

technician.

b. Read the entire Installation & User’s Guide before attempting to use, service or adjust

the pool ﬁltering system or heater.

2. Before repositioning valve(s) and before beginning the assembly, disassembly, or any other

service of the circulating system: (A) Turn the pump OFF and shut OFF any automatic controls

to ensure the system is NOT inadvertently started during the servicing; (B) open the manual air

bleeder valve; (C) wait until all pressure is relieved.

3. Whenever installing the ﬁlter closure FOLLOW THE FILTER CLOSURE WARNINGS EXACTLY.

4. Once service on the circulating system is complete FOLLOW INITIAL START-UP INSTRUCTIONS

EXACTLY.

5. Maintain circulation system properly. Replace worn or damaged parts immediately, (e.g., closure,

pressure gauge, valve(s), o-rings, etc).

6. Be sure that the ﬁlter is properly mounted and positioned according to instructions provided.

NOTE: Turn off power to unit prior to attempting service or repair.

Problems and Corrective Actions

PROBLEM CAUSE REMEDY

Pool water not sufﬁciently clean 1. Pool chemistry not adequate to inhibit Maintain pool chemistry or consult pool service

algae growth. technician.

2. Too frequent a backwash cycle. Allow pressure to build to 10 psi above clean

ﬁlter condition before backwashing.

3. Improper amount or wrong sand size. Check sand bed Freeboard and sand size or

consult a pool service technician.

4. Inadequate turnover rate. Run system for longer time or consult dealer or

pool service technician.

High ﬁlter pressure 1. Insufﬁcient backwashing. Backwash until efﬂuent runs clear.

2. Sand bed plugged with mineral deposits. Chemically clean ﬁlter.

3. Partially closed valve. Open valve or remove obstruction in return line.

Short cycles 1. Improper backwash. Backwash until efﬂuent runs clear.

2. Pool chemistry not adequate to inhibit Maintain pool chemistry or consult pool

algae growth. service technician.

3. Plugged sand bed. Manually remove top 1” surface of sand bed,

replace with new sand and chemically clean entire

sand bed as described in the Chemical Cleaning Procedure.

4. Flow rate too high. Restrict ﬂow to capacity of ﬁlter.

TRITON® Fiberglass Sand Filter Installation and User’s Guide

11

ENGLISH

Return ﬂow to pool diminished, 1. Obstruction in pump hair and Clean basket in pump strainer.

low ﬁlter pressure lint strainer.

2. Obstruction in pump. Disassemble and clean pump.

3. Obstruction in suction line to pump. Clean skimmer basket. Remove obstruction in lines.

Open valves in suction line.

Sand returning to pool 1. Broken under drain lateral. Replace broken or damaged laterals.

Sand loss to waste 1. Backwash rate too high. Reduce backwash ﬂow rate.

2. Improper sand size. Change to proper sand.

3. Air strainer is damaged or missing. Replace damage components.

Leak at closure 1. Improperly tightened closure. Shut off pump, relieve tank pressure,

open air bleeder, tighten closure properly.

2. Dirt or contamination on sealing surface. Shut off pump, relieve tank pressure, open

air bleeder, remove closure and clean all sealing

surfaces. Reassemble closure properly.

3. Damaged part. Same as above except replace damaged o-ring,

closure, tank or any combination of parts as required.

Leak at bulkhead 1. Improper tightened bulkhead assembly. Shut off pump, relieve tank pressure, open air bleeder,

remove closure and remove sand to access leaking

bulkhead on TR40, 50, 60, TR60 ClearPro, 100, 100C,

140 or 140C. Hold the 2” bulkhead and tighten the

2” internal locknut. On the TR100C-3/TR140C-3, using

the special wrench, P/N 154020, hold the 3” ﬂange

spacer and with wrench, P/N 154019, tighten the

3” ﬂange adapter. Hand tighten plus 1/2 turn.

2. Dirt or contamination on sealing surfaces. Shut off pump, relieve tank pressure, open

air bleeder, remove closure and remove sand to

access leaking bulkhead. Remove attached tank

internals and remove bulkhead assembly. Clean all

mating surfaces and seals. Replace the bulkhead

assembly, being careful to assemble properly.

Tigthen assembly as indicated above.

3. Damaged part. Same as above except replace damaged part or

combination of parts.

PROBLEM CAUSE REMEDY

12

TRITON® Fiberglass Sand Filter Installation and User’s Guide

SECTION 5

REPLACEMENT PARTS

Pressure Drop Curve for the Triton® Series Fiberglass Sand Filters

Installing Multiple Filters with Tandem Filter Piping Kits

CAUTION: WHEN MULITPLE FILTERS ARE

INSTALLED, WE HIGHLY RECOMMEND

THE USE OF A PENTAIR TANDEM FILTER

PIPING KIT. THESE KITS INCLUDE

PLUMBING SUPPORTS (BETWEEN

INLET AND OUTLET PIPING AND

BETWEEN OUTLET PIPING AND

FLOOR) TO ASSURE INTEGRITY

OF THE INSTALLATION.

SEE FIGURE A.

CAUTION: PENTAIR RECOMMENDS THE

USE OF A TANDEM FILTER

PLUMBING KIT(S) OR SOME

SORT OF PLUMBING SUPPORT

TO ASSURE PLUMBING INTEGRITY.

FAILURE TO INCLUDE THESE SUPPORTS

COULD VOID YOUR WARRANTY.

FIGURE A.

INLET

OUTLET

0

1

2

3

4

5

6

7

8

010 20 30 40 50 60 70

Pressure Loss (ft)

Flow Rate (GPM)

Pressure Loss Curves (TR40, TR50, TR60)

TR40

TR50

TR60

0

2

4

6

8

10

12

14

16

020 40 60 80 100 120 140 160

Pressure Loss (ft)

Flow Rate (GPM)

Pressure Loss Curves (TR100C/TR100HD, TR100C-3/TR140C-3, TR140C)

TR100C/TR100HD

TR100C-3/TR140 C-3

TR140C

0

2

4

6

8

10

12

14

16

18

20

020 40 60 80 100 120 140 160

Pressure Loss (ft)

Flow Rate (GPM)

Pressure Loss Curves (TR100, TR140)

TR100

TR140

0

1

2

3

4

5

6

7

8

010 20 30 40 50 60 70

Caída de Presión (Ft.)

Índice de Flujo (GPM)

Curva de Caída de Presión (TR40, TR50, TR60)

TR40

TR50

TR60

TRITON® Fiberglass Sand Filter Installation and User’s Guide

13

ENGLISH

TRITON® II & TR60 CLEARPRO FIBERGLASS SAND FILTER

Replacement Parts

20

21 22

24

23

25

29

32

29

30, 31

28

17

18

26

14

16

15

11

13

12

10

7

9

835

5

27

6

3

4

1

234

19

33

TR40

TR50

TR60

TR60 ClearPro

TR100

TR140

MODEL A DIM. B DIM. C DIM. D DIM.

TR40 30 ½ in. 19½ in. 10 ¾ in. 32 ½ in.

TR50 34 ¾ in. 21½ in. 11-7/8 in. 36 ¾ in.

TR60 35 ½ in. 24½ in. 13-5/8 in. 37 ½ in.

TR60 ClearPro 35 ½ in. 24½ in. 13-5/8 in. 37 ½ in.

TR100 39 ¾ in. 30½ in. 16 ¼ in. 41 ¾ in.

TR140 45 ¼ in. 36½ in. 18 ¾ in. 47 ¼ in.

DETAIL B

Before Dec. 1, 1991

6" "V" THREAD

DETAIL A

After Dec. 1, 1991

6" BUTTRESS THREAD

Filters manufactured after Dec 1, 1991 utilize a 6 in.

buttress thread in the ﬁlter tank top opening and on

the closure, see Detail A.

Filters manufactured before Dec 1, 1991 utilize a 6

in. “V” type thread, see Detail B.

6 in. closures in Detail A. and B. are NOT

interchangeable.

18

26

17

★ Used on

TR100 and

TR140 ﬁlters.

14

TRITON® Fiberglass Sand Filter Installation and User’s Guide

Item

No. Part No. TRITON II & TR60 CLEARPRO SAND FILTERS

Description

1 154689 Air bleeder/tee assy.

2 154700 Adapter - brass air bleeder

3 190059 Gauge - back mount pressure

4 154661 O-ring - air bleeder adapter

5 154664 Nut - 3/8 in. - 16 s/s

6152519 Closure face seal - 6 in. buttress thread, see

Detail A u

154559 Closure - 6 in. “V” thread Blk., see Detail B 

7154493 O-ring closure 

152516 O-ring closure 

8 150035 Strainer ECL/TR

9

150039 Tube air relief TR40

150040 Tube air relief TR50/60

150041 Tube air relief TR100

150042 Tube air relief TR140

10

154598 Diffuser assy. TR40/50

154599 Diffuser assy. TR60

154462 Diffuser assy. TR100

154906 Diffuser assy. TR140

11

154803 Piping assy. upper TR40

156814 Piping assy. upper TR50

154533 Piping assy. upper TR60

154426 Piping assy. upper TR100

154500 Piping assy. upper TR140

12 150036 Connector air relief tube

13

154801 Piping assy. lower TR40

156816 Piping assy. lower TR50

154805 Piping assy. lower TR60

155284 Piping assy. lower TR60 ClearPro -1/4 Turn Lateral

154807 Piping assy. lower TR100

154489 Piping assy. lower TR140

14

154636 Tank & ft. assy. TR40 - 6 in. btr. thd., Detail A

154637 Tank & ft. assy. TR50 - 6 in. btr. thd., Detail A

154638 Tank & ft. assy. TR60 - 6 in. btr. thd., Detail A

154639 Tank & ft. assy. TR100 - 6 in. btr. thd., Detail A

154640 Tank & ft. assy. TR140 - 6 in. btr. thd., Detail A

NOTES

u Filters manufactured after Dec 1, 1991 utilize a

6 in. buttress thread in the ﬁlter tank top opening

and on the closure, see Detail A.

 Filters manufactured before Dec 1, 1991 utilize a

6 in. “V” type thread, see Detail B.

 Compatible with closure P/Ns 154570 and

154559

 Compatible with closure P/N 152519

6 IN. CLOSURES IN DETAIL A AND B ARE NOT

INTERCHANGEABLE.

To determine manufacture date, the ﬁrst 4 digits

of the serial number indicate the month and year

product was manufactured.

TR60 ClearPro - 1/4 Turn Lateral for ﬁlters

manufactured after May 15, 2007 utilize Lower

Piping Assy. P/N 155284.

TRITON® II and TR60 CLEARPRO

FIBERGLASS SAND FILTER

Replacement Parts TR40

TR50

TR60

TR60 ClearPro

TR100

TR140

DETAILED VIEW

13

15

16

Detail for Triton® II - TR60 Filters

with ClearPro Technology®

TRITON® Fiberglass Sand Filter Installation and User’s Guide

15

ENGLISH

NOTES

Filters manufactured after Dec 1, 1991 utilize

a 6 in. buttress thread in the ﬁlter tank top

opening and on the closure, see Detail A.

Filters manufactured before Dec 1, 1991 utilize

a 6 in. “V” type thread, see Detail B.

6 in. closures in Detail A. and B. are NOT

interchangeable.

To determine manufacture date, the ﬁrst 4 dig-

its of the serial number indicate the month and

year product was manufactured.

u Used on Filters manufactured before 5-85.

 Used on Filters manufactured after 5-85.

 Used on Filters manufactured before 3-83.

 Used on Filters manufactured after 3-83 thru 3-96.

y For Installations w/out Valve (Pair).

z Used on TR100 & 140 Filters.

NOTE 1: Replacement of tank foot requires the use of foot

mounting tape. See P/N’s.

NOTE 2: Fitting package includes items 1, 2, 4, 5 and 27.

Item

No. Part No. TRITON II & TR60 CLEARPRO SAND FILTERS

Description

15

152290 Lateral - 6 11/16 in. L TR40/50/60, 8 req.

150085 Lateral Assy. - 1/4 turn TR60, 6 req.

150088 Lateral Assy. - TR60 ClearPro, 6 req.

152202 Lateral - 9 1/8 in. L TR100, 8 req. 

154543 Lateral - 6½ in. L TR100, 8 req. u

154540 Lateral - 12 in. L TR140, 8 req.

16

154763 Hub Lateral TR40/50/60

152222 Hub Assy. TR60 ClearPro

154453 Hub Lateral TR100/140

17

152220 Sand drain 2 in. z

154698 Spigot ¾ in. NPT sand drain 

154685 Spigot ½ in. NPT sand drain 

18 154871 Cap thd. 1½ in. z

357161 Plug ¼ in. NPT drain

19

154512 Wrench 6 in. closure

154510 Wrench closure aluminum

151608 Wrench 8½ in. closure aluminum

20 154412 Locknut 2 in. internal, 2 req.

21 154416 Spacer 2 in. internal, 2 req.

22 154492 O-ring 2 in. bulkhead, 2 req.

23 154408 Spacer 2 in. external, 2 req.

24 154538 Gasket 2 in. bulkhead, 2 req.

25 154405 Bulkhead 2 in., 2 req.

26 274494 O-ring 3/16 in. X 2 5/8 in. i.d. z

192115 O-ring #2-12 air adapter

27 154418 Washer 3/8 in. s/s

28

154926 Foot 16 in. dia., TR40/50 (see NOTE 1)

154520 Foot 19 in. dia., TR60 (see NOTE 1)

154596 Foot 24 in. dia., TR100/140 (see NOTE 1)

29 274494 O-ring valve adptr., 2 req.

30 271092 2 in. thd. adptr. kit y

31 271094 1½ in. thd. adptr. kit y

32 271096 1½ in. & 2 in. slip adptr. kit y

33

154641 Kit closure, 6 in. buttress thd., Blk., DETAIL A

154697 Kit closure, 6 in. “V” thd., Tan, DETAIL B

154856 Kit closure, 8½ in. buttress thd., Blk.

34 154687 Fitting package complete (see NOTE 2)

35

154611 Spacer air vent strainer 3¾ in. TR40

154612 Spacer air vent strainer 4½ in. TR50/60

154613 Spacer air vent strainer 5½ in. TR100

154614 Spacer air vent strainer 5 in. TR140

- 154402 Tape ft. mounting TR40/50/60, 3 req.

- 154407 Tape ft. mounting TR100/140, 3 req.

- 151602 Bulkhead wrench 2 in.

- 154714 Bulkhead kit, include items 20-25

TRITON® II and TR60 CLEARPRO

FIBERGLASS SAND FILTER

Replacement Parts TR40

TR50

TR60

TR60 ClearPro

TR100

TR140

16

TRITON® Fiberglass Sand Filter Installation and User’s Guide

26

24

17

28

29

10

9

12

31

30 14

13

11

18

19

15

16

10

11

30 31

932

8

7

5

4

3

6

2

1

27

32

25

37

TR 100C

UPPER PIPING SHOWN

IN ISOMETRIC

TANK VIEW TR 140C

22

20 21 35, 36

20

34

33

23

TR 140C

TR 100HD

TRITON® 100HD, 100C & 140C FIBERGLASS SAND FILTER

Replacement Parts TR100HD

TR100C

TR140C

MODEL A DIM. B DIM. C DIM. D DIM.

TR100HD 39¾ in. 30½ in. 16¼ in. 41¾ in.

TR100C 39¾ in. 30½ in. 16½ in. 43¾ in.

TR140C 45¼ in. 36½ in. 18¾ in. 49¼ in.

Page is loading ...

Pentair Pool TR40 Triton Fiberglass Sand Filter, Triton Fiberglass Sand Filter User manual

Related papers

Other documents