Humandata ACM-205-115C8 User manual

Brand
Humandata
Model
ACM-205-115C8
Type
User manual

This manual is also suitable for

HuMANDATA LTD.
Cyclone IV E FPGA Board
ACM-205 Rev2
User’s Manual
Ver. 2.0
Table of Contents
Revision History ................................................................................................. 1
Introduction ........................................................................................................ 1
1. Fixed Pins [IMPORTANT] .................................................................................... 2
2. Specifications ......................................................................................................... 4
3. Overview ................................................................................................................ 5
3.1. Name of Parts .................................................................................................... 5
3.2. Block Diagram ................................................................................................... 6
3.3. Power Supply ..................................................................................................... 7
3.4. Clock ................................................................................................................... 7
3.5. Configuration Switch (SW1) ............................................................................. 7
3.6. JTAG Connector ................................................................................................. 8
4. FPGA Configuration .............................................................................................. 9
5. Configuration Device Programming ...................................................................... 9
6. Additional Documentation and User Support ...................................................... 10
Precautions
Do Not
1. This product uses ordinary off-the-shelf electronic components, and is therefore inappropriate for use
in applications that require special quality or reliability and are expected to protect human lives or
prevent accidents, such as safety mechanisms in fields including space, aeronautics, medicine, and
nuclear power.
2. Do not be used underwater or in high-humidity environments.
3. Do not be used in the presence of corrosive gases, combustible gases, or other flammable gases.
4. Do not turn on power when circuit board surface is in contact with other metal.
5. Do not apply voltage higher than rated voltage.
Attention
6. This manual may be revised in the future without notice owing to improvements.
7. All efforts have been made to produce the best manual possible, but if users notice an error or other
problem, we ask that they notify us.
8. Item 7 notwithstanding, HuMANDATA cannot be held liable for the consequences arising from use of
this product.
9. HuMANDATA cannot be held liable for consequences arising from using this product in a way different
from the uses described herein, or from uses not shown herein.
10. This manual, circuit diagrams, sample circuits, and other content may not be copied, reproduced, or
distributed without permission.
11. If the product emits smoke, catches fire, or becomes unusually hot, cut the power immediately.
12. Be careful of static electricity.
13. This product may be subject to the export restrictions of Japan, the United States, or other countries.
Purchasers are responsible for properly observing export restrictions.
14. HuMANDATA firmly refuses to export (including reexporting) products to countries or regions subject to
export restrictions.
Product Warranty and Scope of Support
1. HuMANDATA guarantees that its products can be assembled as shown in published circuit diagrams and other design documents.
There may be differences between actual components or their prescribed quantities and model numbers and those shown in circuit
diagrams.
2. Except for the guarantee in item 1, above, no guarantees whatsoever are made. When assembling the product as shown in a circuit
diagram is impossible, and the problem can be solved by revising the diagram, HuMANDATA will revise the diagram. When a
problem can be solved only by replacing components or modifying the product, HuMANDATA will take back the product to replace it
with a properly functioning product.
3. If the problem is minor, HuMANDATA will sometimes describe how to make the revision or modification, and ask the customer to
solve the problem.
4. HuMANDATA will determine how to honor the warranty, as through repair, replacement, return, or other action. The customer cannot
specify what action to take.
5. FPGAs and other components used in products sometimes have characteristic defects. Returns and replacements are not possible
even if such defects are discovered, whether before or after purchase.
6. HuMANDATA shall not be obligated to inform customers about defects in the main components used in products.
7. HuMANDATA shall not be obligated to provide support for products, or to provide support for the software of other companies
needed to use HuMANDATA products.
8. Published documentation shall be limited to that published by HuMANDATA at the time of product purchase, and HuMANDATA shall
not be obligated to provide any other documentation.
9. When repairs or replacements are provided under warranty in Japan, purchaser shall pay shipping charges for shipping to
HuMANDATA, and HuMANDATA shall pay shipping charges for shipping to purchaser.
10. When shipping from outside of Japan, purchaser shall pay all expenses including shipping charges and taxes.
11. Under whatever circumstances, HuMANDATA shall provide support for its products for a maximum of one year after shipping from
factory.
12. The Warranty is not applicable and support ends in the event of fire, storm and flood damage, earthquakes, lightning strikes, and
other natural disasters, as well as conflict or other occurrences.
13. Purchaser is assumed to have read and understood all the above when purchasing a HuMANDATA product.
Limitation of Liability
1. Purchasers assume all liability associated with the use of this product.
2. HuMANDATA assumes no liability whatsoever for any direct, indirect, special, incidental, or consequential damages arising from the
use of this product, even if HuMANDATA has been advised of the possibility of such damage, whether legal or in tort.
3. At the time this product is purchased, items 1 and 2 above shall be deemed to have been confirmed by purchaser.
Trademarks and Other Considerations
1. This manual uses various companies’ trademarks in places.
2. HuMANDATA is this company’s registered trademark.
HuMANDATA’s Philosophy
1. HuMANDATA endeavors to raise product quality. We continually make detailed improvements and adjustments that are not shown
in circuit diagrams.
2. HuMANDATA actively publishes, on the Web and in other ways, information considered useful to customers. Examples would be
how to use FPGAs and how to use development tools.
3. HuMANDATA makes efforts for the long-term provision of products and for continuing their long-term support.
4. Instead of concealing small product problems and documentation errors, HuMANDATA makes them public.
5. HuMANDATA abides by Japanese law and its spirit. We make no transactions with purchasers who commit illegal acts.
1
ACM-205 v2.0
Revision History
Date
Revision
Description
Nov. 17, 2020 v2.0
Revised: Product Revision to Rev2
Change: DDR2 SDRAM
Introduction
Thank you for purchasing our product ACM-205.
This is an evaluation board equipped with an Altera Cyclone IV E, power and clock
circuit and configuration device.
It can provide you with very convenient and easy-to-use environment.
2
ACM-205 v2.0
1. Fixed Pins [IMPORTANT]
Depending on the size of on-board FPGA, some I/O pins are configured to power
pins. FPGA pins listed below are needed to be set as a dummy input. And please do
not use them. If you forget to set them properly, serious damage will cause to the
FPGA board.
Pin
CE30/CE40
Pin Function
CE115
Pin Function Destination
V20
I/O
GND
W9
I/O
GND
M9
I/O
VCCINT
K13
I/O
VCCINT
K15
I/O
VCCINT
L20
I/O
VCCINT
W20
I/O
VCCINT
U20
I/O
VCCINT
W16
I/O
VCCINT
W10
I/O
VCCINT
V9
I/O
VCCINT
T9
I/O
VCCINT
K8
VCCIO1
I/O
J15
VCCIO7
I/O
J13
VCCIO8
I/O
W7
VCCIO2
I/O
AB10
VCCIO3
I/O
Y16
VCCIO4
I/O
U21
VCCIO5
I/O
L21
VCCIO6
I/O
To set whole unused pins, follow the steps below:
1. Open “Assignments” and click “Device…”
2. Click “Device & Pin Options…” button
3. Open “Unused Pins” tab
4. Set Reserve all unused pins as “As input tri-stated”
3
ACM-205 v2.0
Following I/O pins are connected on the board for VREF input.
VREF Pin Bank Group
AB4
B
G9
G12
G14
T7
T8
AA24
C
J22
M21
N21
U23
U24
AB11
D
Y10
4
ACM-205 v2.0
2. Specifications
Model Name
ACM-205-30C8 ACM-205-40C8 ACM-205-115C8
FPGA
EP4CE30F29C8N EP4CE40F29C8N EP4CE115F29C8N
DDR2 SDRAM
MT47H64M16NF-25E:M (Micron, 1Gbit)
Serial FLASH ROM
M25P16 (Micron, 16Mbit)
Config. Device
EPCS64 (Altera, 64Mbit)
On-Board Clock
50 [MHz] (30 [MHz])
Power Input
DC 3.3 [V]
External Clock Input
8
User LED
8
User Switch
3 (Push x 2, Dip x 1bit)
Dimensions
3.386" x 2.126" (86 x 54 [mm])
Weight
36 [g] typ.
User I/O
296
User I/O Connectors
FX10A-80P/8-SV1 (Hirose) x 2
FX10A-100P/10-SV1 (Hirose) x 2
PCB
8 Layer FR-4 t1.6 [mm] Immersion gold
Power-On Reset
240 [ms] typ. (Configuration Reset Signal)
JTAG Connector
DIL 10-pin socket, 2.54 [mm] pitch
Status LED
Power (Red), Done (Blue)
Accessories
DIL10 long pin header (Mounted) x 1
FX10A-80S/8-SV x 2
FX10A-100S/8-SV x 2
Spacer x 4
RoHS Compliance
YES
* There may be cases when compatible parts are used.
5
ACM-205 v2.0
3. Overview
3.1. Name of Parts
Component Side
Solder Side
Power LED
On-Board Clock
Serial I/F
FPGA
JTAG
Configuration SW
User SW
User I/O (CNC)
User I/O (CND)
Config. Device
User I/O (CNA)
User I/O (CNB)
User LED
FLASH ROM
Done LED
DDR2 SDRAM
6
ACM-205 v2.0
3.2. Block Diagram
Cyclone IV E
EP4CE
30/40/115
F29C8N
Us er I/Os CNA
Us er I/Os CNB
64
Us er I/Os CNC
Us er I/Os CND
84
148
64 84
148
VIO(D) INPUT
VIO(B) INPUT Ext Clock (Option)
3.3 V INPUT
JTAG
DONE LED
JTAG
Buffer
Config. Device
EPCS64
.jic
POR (240 ms typ.)
8
3
Us er LED
User Switch
Push x2, DIP x1bit
Power LED (3.3V) Power Circuit
2.5V, 1.8V, 1.2V
ACM-205 Rev.C
Oscillator
50 MHz , (30MHz)
DDR2 SDRAM
( 1 G bit)
Ext Clock (Option)
Ext Clock (Option)
Ext Clock (Option) VIO(C) INPUT
SPI Flash
(16Mbit)
Config. Switch
7
ACM-205 v2.0
3.3. Power Supply
This board operates from single DC 3.3 V power supply from the CNA. Internally
required 2.5[V], 1.8[V] and 1.2[V] are generated by on-board voltage regulators.
Power supply for I/O, VIO(B), VIO(C) and VIO(D), can be input from CNB, CNC
and CND.
External power supply should be sufficient and stabilized. Please do not apply over
3.3V voltage.
For more details, please refer to circuit schematics and FPGA data sheet.
3.4. Clock
Oscillators, 30 MHz (U4) and 50 MHz (U3), are equipped as
on-board clock. By factory setting, 50MHz is supplied. To
supply 30MHz, please change the position of PJ1.
External clock can be input from user I/O connectors.
For more details, please refer to circuit schematics.
3.5. Configuration Switch (SW1)
You can change the configuration mode by configuration switch setting.
For each pins details, please refer to Altera configuration user guide.
SW1
No 2 1
Net Label
ASW2
MSEL0
Factory Setting
OFF
OFF
Function
User
Configuration Mode
Configuration Mode
SW1[1]
Configuration Mode
ON
PS (Passive Serial)
OFF
AS (Active Serial)
You can use MSEL0 to set FPGA’s configuration mode.
PS (Passive Serial) : for JTAG mode access
AS (Active Serial) : for operations below
- Access to an on-board configuration device. (Write/Erase)
- Configure the FPGA from the configuration device. (Power- on)
8
ACM-205 v2.0
3.6. JTAG Connector
This connector is used to configure the FPGA. Pin assignment is as follows.
CN3
Signal Name
JTAG Pin
Signal Name
TCK
1
2
GND
TDO 3 4 VCC
TMS
5
6
-
- 7 8 -
TDI
9
10
GND
Please use attached long pin header when you connect Altera cable.
Please pay attention not to attach cables in reverse.
Notice
9
ACM-205 v2.0
4. FPGA Configuration
To configure the FPGA via JTAG, please refer to the following steps.
1. Open [Tools] menu, then click [Programmer].
2. Select [JTAG] from [Mode] list.
3. Open [Processing] menu, then click [Auto Detect].
4. Double-click [none] and select the sof file you made.
5. Check [Program/Configure] and [Verify].
6. Open [Processing] menu, then click [Start].
If configuration is completed successfully, the DONE LED will light up.
Advice
Check if FPGA device name you set is same as that on the board.
Check unused pins setting. (See section 1)
Quartus II help will give you more information.
5. Configuration Device Programming
To program the configuration device via JTAG , you need to prepare jic (JTAG
Indirect Configuration) file. You can generate jic file from sof file using Quartus II.
Please refer to the following steps.
Generating jic file
1. Open [File] menu, then click [Convert Programming Files].
2. Select [JTAG Indirect Configuration File] from [Programming file type] list.
3. Select the device name which on the board from [Configuration device] list.
4. Fill the [File name] as you like.
5. Click [Add Device], then select [Device family] and [Device name].
6. Click [Add File…], then select the sof file for input file.
7. Click [Generate].
Programming Configuration Device
8. Open [Tools] menu, then click [Programmer].
9. Select [JTAG] from [Mode] list.
10. Open [Processing] menu, then click [Auto Detect].
11. Select the jic file you made.
12. Check [Program/Configure] and [Verify]
13. Open [Processing] menu, then click [Start].
10
ACM-205 v2.0
After programming is completed successfully, turn off and on the power.
Configuration data in the configuration device will be automatically loaded into the
FPGA.
Advice
Check if the configuration device name, FPGA device family name and
device name you selected in step 3 and 5 are same as those on the board.
Quartus II help will give you more information.
6. Additional Documentation and User Support
The following documents and other supports are available at
https://www.hdl.co.jp/en/spc/ACM/acm-205/
Circuit Schematic
Pin List
Outline drawing
Net List
… and more.
Cyclone IV E FPGA Board
ACM-205 Rev2
User’s Manual
Ver. 2.0 ...............................................Nov. 17, 2020
HuMANDATA LTD.
Address: 1-2-10-2F, Nakahozumi, Ibaraki
Osaka, Japan
ZIP 567-0034
Tel: 81-72-620-2002 (Japanese)
Fax: 81-72-620-2003 (Japanese/English)
URL: https://www2.hdl.co.jp/en/ (Global)
https://www.hdl.co.jp/ (Japan)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Humandata ACM-205-115C8 User manual

Brand
Humandata
Model
ACM-205-115C8
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers