BONAIRE Touchpad Control Multi Appliance Owner's manual

Brand: BONAIRE

Model: Touchpad Control Multi Appliance

Category: Air filters

Type: Owner's manual

This manual is also suitable for

PNE2002 Series

Using the

Ducted Gas Central Heating

Dual Cycle Refrigerated Air Conditioning

Ducted Evaporative Air Conditioning

with your

multi-appliance

Touch Pad Control

Owner’s Manual

Please keep this important manual in a safe place. It is the owner’s responsibility to ensure that

regular maintenance is carried out on this ducted heating / cooling product. Failure to do so will

void all guarantees beyond statutory and legal requirements.

www.climatetechnologies.com.au

PNE2002 Series Control

MULTI-APPLIANCE TOUCH PAD

Contents

INTRODUCTION.....................................................................................................................................5

GENERAL INFORMATION..........................................................................................................................6

Important Installation Notice.....................................................................................................................6

Data Location...........................................................................................................................................6

NAVIGATING THE CONTROLS.................................................................................................................7

QUICK START - SIMPLE MANUAL OPERATION ..................................................................................................8

ON / OFF .................................................................................................................................................8

APPLIANCE - selecting the desired appliance.........................................................................................8

MODE - operating your appliance in your preferred mode.......................................................................9

SETUP - setting up or reviewing various functions................................................................................10

Child Lock..............................................................................................................................................10

Temperature / Time Toggle....................................................................................................................10

Zones – where zone motors are fitted....................................................................................................10

Adjustment Arrows.................................................................................................................................11

Reset / Fault Code.................................................................................................................................11

Icons......................................................................................................................................................11

DUCTED GAS CENTRAL HEATING........................................................................................................12

GENERAL INFORMATION...............................................................................................................................13

Important Notice.....................................................................................................................................13

Data Location.........................................................................................................................................13

Assembly. ..............................................................................................................................................13

SAFETY.......................................................................................................................................................14

Safety & Owner Responsibility...............................................................................................................14

Precautions............................................................................................................................................14

Features.................................................................................................................................................14

Power or Gas interruption......................................................................................................................14

USING YOUR TOUCH PAD WITH DUCTED GAS CENTRAL HEATING..................................................................15

THERM Operation (Thermostat)............................................................................................................15

ECONOMY & BOOST for heating..........................................................................................................16

FAN........................................................................................................................................................16

ZONES...................................................................................................................................................17

Setting the open or closed status...........................................................................................................17

Programming Your Touch Pad...............................................................................................................17

Using The Program Mode (PGRM)........................................................................................................19

Program Override (PGRM)....................................................................................................................19

Clock Setup............................................................................................................................................20

Summer Shutdown (Optional)................................................................................................................20

First Startup Or Restart After Shutdown ................................................................................................20

DUCTED GAS HEATING MAINTENANCE..........................................................................................................21

General Maintenance.............................................................................................................................21

Scheduled Maintenance.........................................................................................................................21

PROBLEM SOLVING......................................................................................................................................22

DUAL CYCLE REFRIGERATED AIR CONDITIONING..............................................................................23

Bonaire Control System Page 2

MULTI-APPLIANCE TOUCH PAD

Contents

GENERAL INFORMATION...............................................................................................................................24

Important Notice.....................................................................................................................................24

Data Location.........................................................................................................................................24

Assembly. ..............................................................................................................................................24

SAFETY.......................................................................................................................................................24

Safety & Owner Responsibility...............................................................................................................24

Precautions............................................................................................................................................24

Features.................................................................................................................................................24

Power interruption..................................................................................................................................24

Manual Operation ..................................................................................................................................25

ZONES - Selecting ZONE 1, 2, 3, or 4...................................................................................................26

Programming Your Touch Pad...............................................................................................................26

Programming Sequence........................................................................................................................26

DUCTED EVAPORATIVE AIR CONDITIONING ..........................................................................................27

INTRODUCTION ............................................................................................................................................28

Exhaust..................................................................................................................................................28

Water Management................................................................................................................................29

OPERATING THE TOUCH PAD........................................................................................................................30

Cool Mode..............................................................................................................................................30

Boost Mode............................................................................................................................................30

Thermostat Mode...................................................................................................................................31

Program Mode.......................................................................................................................................31

Program Setup.......................................................................................................................................32

Clock Setup............................................................................................................................................33

DUCTED EVAPORATIVE AIR CONDITIONER MAINTENANCE..............................................................................34

General..................................................................................................................................................34

Filter Pads..............................................................................................................................................34

Water Tank ............................................................................................................................................34

Water Level / Float Valve.......................................................................................................................34

Motor and Fan........................................................................................................................................35

Electrical................................................................................................................................................35

Bleed Off................................................................................................................................................35

Pump......................................................................................................................................................35

Water Distribution ..................................................................................................................................35

No Seasonal Maintenance.....................................................................................................................35

TROUBLE SHOOTING GUIDE .........................................................................................................................36

CONTROL SETUP................................................................................................................................37

SETTING UP THE CONTROL - GENERAL.........................................................................................................37

Before Starting.......................................................................................................................................37

Installation..............................................................................................................................................37

USING THE SETUP MODES ...........................................................................................................................38

Product Identification..............................................................................................................................38

CODING.......................................................................................................................................................39

Auto-Coding...........................................................................................................................................39

Bonaire Control System Page 3

MULTI-APPLIANCE TOUCH PAD

Contents

Coding Defaults .....................................................................................................................................39

Forced Scan Auto-Coding:.....................................................................................................................39

Important Notes .....................................................................................................................................39

MULTIPLE UNIT SETUP – HEATER / COOLER..................................................................................................40

Force Coding a New / Additional Product..............................................................................................40

Fault Codes Access...............................................................................................................................41

View The Fault Code..............................................................................................................................41

Fault Codes For High Efficiency, Mid Efficiency Heaters.......................................................................42

Resetting the Touch Pad Control...........................................................................................................43

Calibrating the Thermostat.....................................................................................................................43

EVAPORATIVE AIR CONDITIONING SETUP......................................................................................................44

Setting the Water Management Systems Parameters and values.........................................................44

Setting the Water Level & Bleed rate.....................................................................................................45

Fan Speed Settings ...............................................................................................................................46

MULTIPLE UNIT SETUP – EVAPORATIVE COOLERS.........................................................................................47

Setting the Common Zone For Multiple Units........................................................................................48

Scan For Products:................................................................................................................................48

DUCTED GAS CENTRAL HEATING..................................................................................................................49

Setting Fan SPEEDS – High / Low........................................................................................................49

Setting Fan Speeds - Zoning.................................................................................................................50

Setting the Zone Availability - Heating...................................................................................................51

COMMISSIONING CHECK LIST ...............................................................................................................53

General..................................................................................................................................................53

Unit – Ducted Heating............................................................................................................................53

Unit – Dual Cycle Refrigerated Air Conditioning....................................................................................53

Unit - Ducted Evaporative Air Conditioner .............................................................................................54

Ductwork................................................................................................................................................54

Site.........................................................................................................................................................54

Customer Hand Over.............................................................................................................................54

WARRANTY .......................................................................................................................................55

SERVICE.........................................................................................................................................59

Bonaire Control System Page 4

MULTI-APPLIANCE TOUCH PAD

Introduction

You have chosen one of the world's most advanced control systems incorporating the latest technology.

The Touch Pad control is an Australian and world first for its use with ducted heating and cooling systems.

Designed exclusively for Climate Technologies air comfort products, the self-prompting display panel

controls your unit’s functions, providing the ultimate in heating and cooling flexibility.

This technologically advanced controller comes with manual and thermostat control, programmable timer,

boost function plus many other setup functions.

Your Touchpad Control has been designed to operate the following Climate Technologies products:

Heating – 3, 4, 5 Star Ducted Gas Central Heaters.

Dual Cycle Cooling - Refrigerated Air Conditioning (cooling only) designed to Dual Cycle to Ducted Gas

Central Heaters.

Fresh Air Conditioners - Ducted Evaporative Air Conditioners.

Bonaire Control System Page 5

MULTI-APPLIANCE TOUCH PAD

Introduction

Your Touch Pad Control is designed to automatically detect the appliances during the commissioning of the

unit by the installer. Controller options not required for your appliances will usually not be visible on your

Touch Pad display.

Additional control accessories that can be added to

your Touchpad control for enhanced operation

include:

Remote Thermostat – an extra thermostat that

can be connected in conjunction with the

Touchpad to individually control a zone motor in

a specified area of a ducted gas heating

system.

Home Automation – allows the unit to be

turned ON or OFF through most home security

systems.

Your Touch Pad is designed in Australia to suit

Australian conditions and will ensure that your

home is comfortable all year round.

GENERAL INFORMATION

IMPORTANT INSTALLATION NOTICE

A licensed person is required to install Climate Technologies equipment. If the equipment is not installed in

accordance with the installation instructions and the governing body regulations, Climate Technologies

reserves the right to refuse service on non compliant installations.

Subject to state regulations and by laws a certificate of compliance must be issued for the electrical and

plumbing connections certifying that the work complies with all the relevant standards.

Note: Only a licensed person will have insurance protecting their workmanship.

DATA LOCATION.

Your appliance model number, serial number and model description are located on the appliance data plate

on the end of the heater or inside the cooler in the vicinity of the electronic controls. These details should

also be in the warranty section of this booklet.

You will need this information, should your appliance require servicing, spare parts or just if you require

additional information about this product.

Bonaire Control System Page 6

MULTI-APPLIANCE TOUCH PAD

Navi

atin

the Controls

Nav

igating the Controls

Number Description Function

1 ON / OFF Turns the unit ON or OFF

2 APPLIANCE Touch any area within the APPLIANCE outline to select

product.

3 CLOCK / TEMPERATURE 12 hour clock denoting AM / PM and the day OR room

and SET temperature for HEATING and DUAL CYCLE

cooling mode.

4 MODE Touch any area within the MODE outline and the available

operating modes will be displayed.

5 SETUP Touch any area within the SETUP outline and the

available setup icons will be displayed.

6 FUNCTION SYMBOLS Symbols indicate the unit components functioning.

7 UP / DOWN ARROWS Arrows will adjust the output of the unit.

8 FUNCTION LEVEL Function level displays the output level settings with

graphic bars

9 ZONES Controls zones for Ducted Gas Heating / Dual Cycle Air

Conditioning. Where there is more than one unit fitted the

zones buttons can control the ON / OFF function of one or

more units. Each unit is then treated as a zone.

10 PERIOD In PRGM mode there are 4 operating periods available.

The 1, 2 , 3, 4 advises which operating period the program

is in.

Bonaire Control System Page 7

MULTI-APPLIANCE TOUCH PAD

Navi

atin

the Controls

Quick Start - Simple Manual Operation

Here's all you have to do to get going (if the installer hasn't already done it for you).

Step 1 Turn the control ON at the ON

/ OFF button.

Step 2 Select the Appliance if not already

selected in the APPLIANCE area.

Step 3 Select the MODE of operation required

by pressing anywhere within the MODE

area.

(The icon availability will vary according

to the Appliances selected. See display

options below)

Press the required mode so the

selection is solid. The remaining icons

will flash 5 more times and disappear.

Step 4 Use the arrows to vary the

unit output.

Refer next page for more details.

ON / OFF

When pressing the ON / OFF button to turn the unit on,

the touch pad control will return to the last used setting.

APPLIANCE - SELECTING THE DESIRED APPLIANCE

Press any area within the Appliance outline for the available appliances.

• If only one appliance type is fitted the control will BEEP.

• If more than one appliance type is installed the COOL and HEAT icons will flash. Make your

selection by pressing the required product icon. Once selected the icon will become solid. The

remaining icon will continue to flash a further 5 times then disappear.

When the touchpad is turned on the last appliance used will be activated.

This control is capable of controlling the following Climate Technology products installed with PNE

control systems:

• Ducted Gas Central Heating

• Dual Cycle Ducted Gas Central Heating and Dual Cycle Refrigerated Air Conditioning

• Ducted Evaporative Air Conditioning

• Ducted Gas Central Heating and Ducted Evaporative Air Conditioning.

Bonaire Control System Page 8

MULTI-APPLIANCE TOUCH PAD

Navi

atin

the Controls

Mode / Icon Options

To view the MODE options available press the touch pad anywhere within the MODE outline. The

available functions will be dependent on the products installed.

Ducted Gas Heating

Available Icons HEAT Appliance

(

Ducted Gas

)

Ducted Evaporative A/C

Available Icons COOL Appliance

Dual Cycle Refrigeration A/C

Available Icons COOL Appliance

MODE - OPERATING YOUR APPLIANCE IN YOUR PREFERRED MODE

• COOL – Evaporative Air Conditioning Only

Fan and Pump in manual mode. This means the fan can be adjusted manually via the UP

/ DOWN arrows and the pump operates continuously.

• BOOST – Ducted Gas Central Heating and Evaporative Air Conditioning Only

The room air fan will operate at maximum speed.

• PGRM - Ducted Gas Central Heating, Evaporative Air Conditioning, Dual Cycle Air Conditioning

The unit can be set up in Program Mode to turn the unit ON and OFF in the desired mode.

For ducted heating and dual cycle refrigeration this is a 7-day program.

For ducted evaporative air conditioning this is a 1-day (24-hour) program.

• FAN – Ducted Heating and Evaporative Air Conditioning.

Fan only in manual mode. This means the fan only can be run and adjusted via the UP /

DOWN arrows.

In dual cycle cooling mode the fan will run continuously while the condenser cycles ON

and OFF

• THERM – Ducted Gas Central Heating, Evaporative Air Conditioning, Dual Cycle Air Conditioning

Thermostat mode will control the unit via a temperature sensor located inside the touchpad

itself.

Set the comfort level and the unit will automatically increase or decrease the amount of

heating or cooling required according to demand.

Adjust the comfort level using the UP / DOWN arrows

• ECON – Ducted Gas Central Heating Only

Economy will run a ducted gas central heater at the lowest available fan speed and gas

setting. This is best used once the space has been brought up to temperature.

Bonaire Control System Page 9

MULTI-APPLIANCE TOUCH PAD

Navi

atin

the Controls

SETUP - SETTING UP OR REVIEWING VARIOUS FUNCTIONS

To view the SETUP options available, press the touch pad

anywhere within the SETUP outline. The available

functions are:

• PGRM – Program setup allows you to create a timed

program to start and stop the product. There are 4

period programs available requiring a minimum of 2 to

be set per day.

For ducted evaporative air conditioning the program

option will only function for 24 hours and then the unit

will stop.

• CLOCK – Setting the time

• REVIEW – Pressing the review button will

automatically step the control through the timer

programs set.

CHILD LOCK

This function is designed to be a simple mechanism to lock

the control to prevent unnecessary adjustments to the

system. When the lock is engaged there will be no system

functions available. (This is available in either on or off

modes)

• To engage the Child Lock press and hold anywhere

over the numeric display for 4 seconds. A BEEP

followed by a BEEP will be heard to indicate the lock is

ON.

• To remove the child lock press and hold anywhere over

the numeric display for 4 seconds. A Single BEEP

followed by another single BEEP will be heard to

indicate the lock is OFF.

TEMPERATURE / TIME TOGGLE

To change the display between temperature and time just

press anywhere in the numeric display. In Evaporative

Cooling mode only the time will be displayed.

ZONES – WHERE ZONE MOTORS ARE FITTED

The zone motor option is only available with ducted gas

heating / dual cycle products. These icons allow zones to be

turned ON or OFF. This function will ONLY be made

available by the installer if zone motors have been fitted to

your duct work.

Bonaire Control System Page 10

MULTI-APPLIANCE TOUCH PAD

Navi

atin

the Controls

ADJUSTMENT ARROWS

The adjustment arrows can be used to increase or decrease

the function of product being controlled. The icons will come

on automatically to indicate the unit’s mode of operation.

RESET / FAULT CODE

If the reset icon appears and the touchpad thermostat is

flashing information in clock area, it means the unit has

stopped as the result of a fault e.g. electricity / gas

interruption or some other malfunction.

The information being displayed will continually rotate

between the unit identification and the fault code e.g. HC: 01

and F: 04. Before resetting the control, note the fault code

information. Should a service call be required, this will assist

in quick diagnostics and service requirements.

To RESET the unit, press and hold the RESET icon for

approximately 4 seconds until 2 Beeps have been heard. The

reset icon will disappear and your appliance will be reset. If

there has been no component failure the unit will now resume

its function.

ICONS

The operating icons will be displayed relative to the unit’s operation.

1. Indicator Bars

Evaporative Air Conditioning

(Manual Mode) shows fan speed.

(Thermostat Mode) comfort settings.

Central Heaters shows fan speed setting in FAN mode.

2. Snow Flake Symbol

For evaporative air conditioning it indicates that the

pump is on.

For Dual Cycle Refrigerated Air Conditioning it indicates

that the condenser is operating.

3. Fan Symbol

For Evaporative Air Conditioning it indicates that the fan is operating.

For Ducted Heating it indicates that the fan is operating.

For Dual Cycle Refrigerated Cooling it indicates that the fan is operating.

4 Flame Symbol

Indicates that the thermostat is calling for heat from the ducted central heater

Bonaire Control System Page 11

MULTI-APPLIANCE TOUCH PAD

Ducted Gas Central Heatin

Ducted Gas Central Heating

Owner’s Operation and Maintenance Details

Please keep this important manual in a safe place. It is the owner’s responsibility to ensure that

regular maintenance is carried out on this Ducted Gas Central Heater. Failure to do so will void all

guarantees beyond statutory and legal requirements.

www.climatetechnologies.com.au

Bonaire Control System Page 12

MULTI-APPLIANCE TOUCH PAD

Ducted Gas Central Heatin

Congratulations on purchasing this ducted gas central heating system, an exciting new product

manufactured by Climate Technologies.

Wholly designed and manufactured in Australia, this Ducted Gas Central Heater represents an exciting

new development in warm air furnace design. It embodies the latest advances in gas heating technology.

Your heater is supported by Climate Technologies, Australia’s most advanced manufacturer of a

complete range of climate control products.

To ensure you fully enjoy the benefits of this Ducted Gas Central Heater, please read these instructions

carefully and keep them handy for future reference.

Operated and maintained in accordance with this manual, this unit will provide you with years of warm

and environmentally friendly operation. Please take the time to read this manual.

NOTE: The manufacturer and its service providers reserve the right to refuse service unless

safety and accessibility to the unit can be guaranteed in accordance with the installation

instructions and Australian Standards. The cost of any extra equipment required to provide

access to the unit for servicing is the responsibility of the owner.

General Information

IMPORTANT NOTICE

A licensed person is required to install Climate Technologies equipment. If the equipment is not installed

in accordance with the installation instructions and the governing body regulations, Climate Technologies

reserves the right to refuse service on non compliant installations.

Subject to state regulations and by laws a certificate of compliance must be issued for the electrical and

plumbing connections certifying that the work complies with all the relevant standards.

Note: Only a licensed person will have insurance protecting their workmanship.

DATA LOCATION

Your appliance model number, serial number and model description are located on the appliance data

plate on the end of the heater or under the lid in the vicinity of the electronic controls. These details

should also be in the warranty section of this booklet.

You will need this information, should your appliance require servicing, spare parts or just if you require

additional information about this product.

ASSEMBLY

There is no assembly required of this Ducted Gas Central Heater. Your Dealer or installer will carry out

all assembly and commissioning upon installation.

Bonaire Control System Page 13

MULTI-APPLIANCE TOUCH PAD

Ducted Gas Central Heatin

Safety

SAFETY & OWNER RESPONSIBILITY

The manufacturer and its service providers reserve the right to refuse service unless safety and

accessibility to the unit can be guaranteed. The cost of any extra equipment required to provide access

to the unit for servicing is the responsibility of the owner.

PRECAUTIONS

DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.

DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

DO NOT PLACE ARTICLES IN FRONT OF OR OVER THE RETURN AIR GRILLE.

FEATURES

Your Ducted Gas Central Heater has all the safety devices to ensure safe operation. These devices

conform to the standards set out by the Standards Australia.

POWER OR GAS INTERRUPTION

Should there be an interruption to the power supply during the heating operation the controls will

automatically turn off the gas.

The heater will be ready to resume operation once the power has been restored.

Should there be an interruption to the gas supply, the heater will endeavor to re-light 3 times and if

unsuccessful will lock out. (This is part of the safety features). Should this occur the heater will need to

be reset. If the RESET icon is displayed, press and hold the RESET icon till a BEEP is heard and the

unit will be ready to resume operation.

Please refer to your problem-solving chart to assist resolving other problems.

Bonaire Control System Page 14

MULTI-APPLIANCE TOUCH PAD

Ducted Gas Central Heatin

Using Your Touch Pad with Ducted Gas Central Heating

Using your Touch Pad for manual operation of your Central Heating when you want direct control,

without timers or programming.

THERM OPERATION (THERMOSTAT)

Step 1 To turn the Touch Pad on, press and release the

ON/OFF button. If there is only a central heater

HEAT will automatically display in the Appliance

Outline.

NOTE: Your Touch Pad Control is designed to

automatically detect the appliances you have

installed. Options not required for your appliances

will not be displayed on the touchpad. So don't

worry if you don't see all the menu items listed in

this book.

Step 2 Press anywhere within the MODE outline.

The available icons will flash. Select THERM. The icon will

become solid and the remaining icons will flash 5 more times

before disappearing.

Step 3 Press the arrows to increase or decrease the set

temperature (TEMP).

Step 4 Your Touch Pad measures the room temperature using a thermostat inside its case. The Touch

Pad will run the Heater until it measures temperature a little above your set temperature and

then turn off the unit. When the temperature falls a little below the set temperature the unit will

restart. The unit operation will be as follows:

• When the room temperature (ROOM) is colder than the set temperature (TEMP) the heater

will come on after approximately a 30 second ignition process

• If at start up the room temperature (ROOM) is 2.0° or more below the set temperature

(TEMP), the central heater will start up at high fan speed and high gas rate bring your

house up to temperature as quickly as possible.

• As the room temperature gets closer to the set temperature the central heater will reduce

the room air fan and the gas rate to the burner.

• When the thermostat reaches the set temperature the central heater will be on low fan and

the gas will modulate to low fire.

• When the temperature has gone over the set temperature by 0.5° the central heater will

shut down.

• When the temperature has dropped to 1° below set temperature the unit will restart.

The flame symbol will be displayed on the control to indicate the heater is

functioning.

•

Step 5 To turn the heater OFF Press the ON/OFF button on the touchpad.

Bonaire Control System Page 15

MULTI-APPLIANCE TOUCH PAD

Ducted Gas Central Heatin

The Touch Pad remembers your SET TEMPERATURE setting and uses it next time you turn it ON.

As your activities vary, you may find you need different temperature settings, e.g. a

temperature comfortable for sitting is usually too warm compared to when you’re moving

about.

For economical operation, set a lower set temperature during the day when you are active, or use

economy (ECON). Switch the Touch Pad OFF when asleep and ON again when awake. These cost

saving functions can be programmed to operate automatically (see Programmed Control).

ECONOMY & BOOST FOR HEATING

Economy (ECON) operates the heater at the lowest fan

speed and a lowest possible gas rate. This is best used

once the space has been brought up to temperature.

BOOST operates the heater at the highest fan speed and

a highest possible gas rate.

The unit will switch off when the SET TEMPERATURE is

reached.

Step 1 To select economy or boost switch the Controller

ON.

Step 2 Ensure the APPLIANCE outline is set to HEAT.

Step 3 Press any where in the MODE outline to see the

available icons.

Step 4 Press the ECON or BOOST icon so that it stops

flashing. The remaining icons will flash 5 more

times and disappear.

Step 5 Use the arrows to adjust the

SET temperature as required.

FAN

The fan in your heater can be used to circulate the room

air without running the heater. To run the fan only option:

Step 1 To select FAN only switch the Controller ON

Step 2 Ensure the APPLIANCE outline is set to HEAT.

Step 3 Press any where in the MODE outline to see the

available icons.

Step 4 Press the FAN icon so that it stops flashing. The

remaining icons will flash 5 more times and

disappear. The room air fan will now run.

Step 5 Use the arrows to adjust the fan

speed as required.

Bonaire Control System Page 16

MULTI-APPLIANCE TOUCH PAD

Ducted Gas Central Heatin

ZONES

Selecting ZONE 1 2 3 4 only applies if your home is fitted

with optional motorised ductwork dampers (please consult

your installer) that allow opening or closing of each section

of ducting.

Many homes have no motorised ductwork dampers fitted,

however the control will still display the zones. Where

zone motors are fitted the installer can set your controller

to show only the zones available for use.

In homes with more than one zone, the default requires at least one zone open at all times. The common

zone feature, which allows all zones to be turned off, can only be applied to specific duct designs. This

must ONLY be set by the installer.

SETTING THE OPEN OR CLOSED STATUS

Step 1 To select ZONES switch the Touch Pad Control ON.

Step 2 Ensure the Appliance is set to HEAT and THERM.

Step 3 Press any where in the ZONE area to see the available zone icons.

Step 4 To turn a ZONE ON, press the ZONE icon required to make it solid.

To turn a ZONE OFF press the ZONE icon to make it flash.

The flashing icons will flash 5 more times and disappear. In approximately 30 seconds the new zone

settings will be effective.

PROGRAMMING YOUR TOUCH PAD

Programming your Touch Pad will provide energy and operating time savings. Your heating and or cooling

system will only operate when you need it, and at your chosen comfort levels.

Determine your most comfortable settings, program them and let your Touch Pad do the rest

automatically.

Turning on the program function

Press the PRGM button in the mode panel to run program.

Programming Sequence

If you've never programmed your Touch Pad control

before (or it’s been a while) remember it's easier to

program the whole week to the same settings (by

selecting the whole week MON TUE WED THU FRI

SAT SUN day choice) and then program variations for

particular days or the weekend as you become more

familiar with programming.

If the Controller exits program mode it may be because you've paused longer than about 60 seconds to

make your next choice. All the settings you've made up to then in a completed program period (Period 1,

2, or 3) will be saved. Just switch back to PRGM in setup, select the day combination and scroll through

your settings using the ENTER key and carry on from where you left off.

Bonaire Control System Page 17

MULTI-APPLIANCE TOUCH PAD

Ducted Gas Central Heatin

During the program sequence only the icons requiring changing for each step will be displayed.

In the SETUP outline, there are 2 setup mode icons PGRM and CLOCK as well as 4 function icons,

ENTER, CANCEL, REVIEW and FINISH. To enter setup mode, touch anywhere within the SETUP

outline. The accessible icons will be displayed.

Program Setup

Program setup will take you through the steps to set your Ducted

Gas Central Heater up for automatic control:

Step 1 To select the PGRM (Program) mode touch anywhere

in the SETUP outline.

Step 2 Press PGRM. The 3 icons will disappear and edit

mode has begun with the 1st period.

Two new icons will now be displayed ENTER &

CANCEL.

ENTER will save each step of the program •

• CANCEL will step back the program 1 step at a

time.

Step 3 Using the arrows select the day or day grouping to program. Press ENTER

Step 4 Period 1 will be displayed with ON or OFF. Using the arrows make a selection if

required and press ENTER.

Step 5 Set the Hour using the arrows and press ENTER

Step 6 Set the Minutes using the arrows and Press ENTER

Step 7 Change the Unit in the APPLIANCE area if required.

Step 8 Select the MODE of operation, THERM, ECON, BOOST, FAN (only) and press ENTER.

Step 9 If zones are fitted, select the zones required to be open.

Step 10 Adjust the SET temperature using the arrow. Press ENTER

Default Setup Ducted Gas Central Heating

Program

The First Program period is now completed.

Step 11 Program the second period using steps 4 to 9

Event ON/OFF Start Time Mode

Step 12 If only 2 program periods are required press

FINISH. If a 3rd period is required program

using steps 4 to 9.

1 ON 6:00 am THERM

2 OFF 9:00 am -

Step 13 If only 3 program periods are required press

FINISH. If a 4th period is required program

using steps 4 to 9 and press FINISH.

3 ON 4:00 pm THERM

4 OFF 10:00 pm -

IMPORTANT NOTE: The program does not automatically start at this point.

Bonaire Control System Page 18

MULTI-APPLIANCE TOUCH PAD

Ducted Gas Central Heatin

To start the program, touch the MODE outline area for the available icons to be displayed. Press PRGM

icon and make solid. The icons will flash 5 more times and program mode will be engaged.

Reviewing Entered Programs

REVIEW is a feature that allows you to first view the current program

settings. Each step remains visible for 3 seconds.

Once the review procedure has started the FINISH icon will be illuminated.

The FINISH icon can be used to stop the REVIEW process.

USING THE PROGRAM MODE (PGRM)

Activates the 4 program x 7 day / night timer.

To operate the PGRM mode:

Step 1 Turn the Touch Pad on, press and release the

ON/OFF button. If there is only a central

heater HEAT will automatically display in the

Appliance area.

Step 2 Press the MODE outline. The available icons

will flash. Select PGRM.

The icon will become solid and the remaining

icons will flash 5 more times before

disappearing.

The touchpad will now be in program mode with the current program settings being indicated e.g.

time period, mode of operation, period and settings.

Step 3 To exit the PGRM mode you have 2 options.

1. Turn the unit off using the ON OFF button

2. Press the MODE area. The available icons will flash. Select a new mode of operation.

PROGRAM OVERRIDE (PGRM)

When PGRM is selected, the program can be overridden within an event period (1, 2, 3, or 4) without

altering the program setup. There are 2 scenarios for changing the event:

1. When the program event is ON, operating the unit:

The operating parameters can be altered temporarily. Simply adjust the temperature or change the

zone selection (where fitted) at any time.

2. When the program event has the unit turned OFF.

To override the PGRM mode when the unit is scheduled to be OFF, press and hold the PGRM

mode button for 5 seconds until it beeps and then immediately select one of the mode functions

available. The PGRM button will remain illuminated with your new selection.

The event number will now flash, indicating a temporary change to the program. The program will reset

itself once the next timed event has started or if the PRGM in the mode section is turned OFF then ON or if

the touchpad has been turned OFF then ON.

Bonaire Control System Page 19

MULTI-APPLIANCE TOUCH PAD

Ducted Gas Central Heatin

CLOCK SETUP

Timer setup will take you through the steps to set your 12-hour clock. You

can use FINISH at any stage of setting the Day and Time.

Step 1 To select the CLOCK setup touch anywhere in the SETUP

outline.

Step 2 Press CLOCK. The 3 icons will disappear and edit mode has

begun.

Step 3 Three new icons will now be displayed ENTER, CANCEL &

FINISH.

ENTER will save each step of the program •

•

• CANCEL will abort the setup and no entries will be saved.

FINISH allows you to stop at any time and save the settings.

Step 4 Adjust the hours using the arrows. Press

ENTER

Step 5 Adjust the minutes using the arrows. Press

ENTER.

Step 6 Adjust the day using the arrows. Press

ENTER

Time setup is now complete and all functions are resumed.

SUMMER SHUTDOWN (OPTIONAL)

Step 1 Switch the Touch Pad OFF

Step 2 Switch the power point OFF and turn the gas tap OFF. These connections are usually located

close to the Heater.

FIRST STARTUP OR RESTART AFTER SHUTDOWN

Step 1 Switch on the power point to the heater. Turn on the gas tap on the gas supply line into the

heater.

Step 2 Switch the Touch Pad ON.

Step 3 Select HEAT in the Appliance area if not already displayed.

Step 4 Press the arrows to increase or decrease the SET TEMPERATURE. If the set

temperature is greater than the room temperature, the heater will resume operation.

Bonaire Control System Page 20

Page is loading ...

BONAIRE Touchpad Control Multi Appliance Owner's manual

Brand: BONAIRE

Model: Touchpad Control Multi Appliance

Category: Air filters

Type: Owner's manual

This manual is also suitable for

PNE2002 Series

Download PDF

report

BONAIRE Touchpad Control Multi Appliance Owner's manual

This manual is also suitable for

BONAIRE Touchpad Control Multi Appliance Owner's manual

Related papers

Other documents