forums.dpreview.com http://forums.dpreview.com/forums/post/24921509
K100D (Super) Pictorial guide to using manual lenses
[imgs]
Thanks in large part to the information I've gleaned from this forum, I've just purchased a K100D Super to take
advantage of the Pentax equipment left over from my old film days. In these days of rapid obsolecence, it's
wonderful to be able to buy a modern camera and still be able to use it with my 25- year-old equipment. Kudos,
Pentax!
Once I got the camera set up correctly it works very nicely with my old manual lenses. But I've seen several posts
questioning how to do this, so as a thanks to the forum I've put together the following illustrated guide. Perhaps it
will inspire a few folks who have some old lenses sitting around to wander down to their local camera store and
give them a try.
GETTING STARTED - configuring the camera:
The camera won't allow you to take pictures with manual lenses until you configure it properly. Press the "menu"
button, go right until you see the "Custom Setting" menu, and then go down a few menu pages until you see the
"Using aperture ring" setting:
At this menu item go right, select "Permitted", and hit the OK button.
Now you can use your manual lenses. Note that this only has to be done once, and there's no need change the
setting back again in order to use the auto- aperture or auto- focus lenses. Once you've set it just leave it that way
and your camera will happily work with whatever lens you throw at it.
Next: Getting ready to shoot (see reply)
forums.dpreview.com http://forums.dpreview.com/forums/post/24921558
GETTING READY TO SHOOT - mounting a manual lens:
First step (pretty obvious really) is to mount the manual lens on your camera. Nothing special here, manual lenses
mount just like automatic ones (with the exception of screw- mount lenses which require an adapter. I'm not
covering them here because I don't own any, sorry!)
The second step is to set the camera to "M" (Manual) mode:
Next, set the focusing mode to "MF" (Manual Focus). There are some options regarding focusing that I'll mention
below, but to get started "MF" will work best.
Turn on SR (Shake Reduction) by flipping the switch near the lower-right corner of the LCD:
...and then turn on the camera:
When the camera is powered up with Shake Reduction turned on and a manual lens mounted, it will ask you for
the focal length of the lens so it knows how much SR to apply when the camera moves. Use the left/right
directional keys on the back of the camera to select the proper focal length and press OK. If you're using a z oom
then try to choose a focal length that's as close to what you'll actually shoot with as possible. For example, if
you're using an 80- 200 z oom at around the halfway point, choose 135mm as the focal length:
You won't see this screen if you turn on SR with the camera already powered up. You can get to this screen by
going through the menu screens (it's just about the last item on the "record" menu), but I find it quicker just to turn
the camera off and then on again.
And now you're ready to shoot some beautiful photographs with that manual lens!
Next: Shooting (see reply)
forums.dpreview.com http://forums.dpreview.com/forums/post/24921563
SHOOTING:
It will take longer to describe this than it does to actually take a shot, so bear with me:
First, set the aperture ring on the lens to the f/stop you will use:
Next, look through the viewfinder and focus:
Half- press the shutter button to turn on the exposure meter:
You can tell the meter is on when the green digits below the viewfinder image light up (there's a menu option that
controls how long the meter stays on - use if if the digits shut off too quickly for your taste). Because it's a manual
lens, the camera has no idea what f/number you've set it to, so it will show "F(blank)" for the aperture.
And here's the secret to metering with the manual lenses: while the meter is still on, press the "AE- L" button on the
back of the camera (it'll probably be very close to where you thumb naturally sits):
When you hit the button the camera will momentarily stop down the lens to take a light reading, then it will set the
shutter speed to the appropriate exposure. You'll see the new shutter speed in the green digits below the
viewfinder image. After setting the shutter speed the lens will immediately open back up again - the whole thing
takes about a second.
If you think the shutter speed is to slow (or too fast!), adjust the aperture (or ISO sensitivity) and repeat (half- press
the shutter to turn on the meter and then press the AE- L button to set the shutter speed).
Everything is set, now just fully depress the shutter button to take the picture:
...and that's it! Once you've got the aperture set in the range you want, the only difference between shooting an
automatic vs. a manual lens that you have to focus the manual lens manually (duh!) and you have to press the
AE- L button to set the shutter speed. And if the lighting conditions aren't changing then you don't even have to do
that. In fact, with constant lighting and a subject that stays within your depth of field, you can probably fire shots off
even faster than with an automatic lens!
Next: More on Focusing, and Summary (see reply)
forums.dpreview.com http://forums.dpreview.com/forums/post/24921571
MORE ON FOCUSING
One of the interesting things that the camera can do is to "assist" your manual focusing. This is enabled in the
custom setup menu ("FI with S lens used"). If enabled, then while the meter is on the autofocus sensor monitors
your focusing (using the centre focus point only). When you hit the right focus point the green hexagon below the
viewfinder will light up and stay on. I've found that in dim lighting conditions and with fast lenses (ie, 50mm f/1.4),
the focus detection is very touchy and seems more distracting than helpful. But if you find it too annoying you can
just go back into the menu and disable it again.
If you do enable the focus assist, you can also use what's known as "focus trap" mode. This is enabled by turning
the autofocus switch to the "AF" position. Of course the camera can't actually autofocus a manual lens, but in this
position it will disable the shutter button unless you've got good focus and the green hexagon is lit in the
viewfinder.
You should be able to use this for difficult focusing situations - macros spring to mind. Set the autofocus switch to
"AF", frame the subject in the viewfinder, focus as best you can and then hold down the shutter button while
slowing moving to and from the subject. With the shutter button held down, the camera will fire as soon as you hit
the correct focus point.
It sounds good in theory, although I admit I haven't actually tried this particular technique yet.
SUMMARY
There are a few things that need to be set up, but once that's done it's actually very easy to use manual lenses.
Pressing the AE- L button to set the shutter speed is simple to do and faster than mucking about with the shutter
speed on my old K1000 and ME Super cameras.
The only caveat is that the smaller APS- C sensor used in Pentax's digital cameras means that lenses have a
reduced field of view compared to when they're used on a full- frame 35mm camera. The effect is like multiplying
their focal length by 1.5, so that a 50mm lens on a K100 digital camera gives you the same picture you'd get with
a 75mm on a film camera. This is a disadvantage if you want to take wide shots, but an advantage for telephoto.
If you've got some old Pentax lenses lying around, the K100 will put them to good use!
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
