Creda SF3 Installation guide

Brand: Creda

Model: SF3

Category: Space heaters

Type: Installation guide

CREDA HEATING

MILLBROOK HOUSE, GRANGE DRIVE, HEDGE END, SOUTHAMPTON, SO30 2DF

UK - TEL: 0844 879 3588 / FAX: 0844 879 3583 / Website: www.credaheating.co.uk

R.O.I. - TEL: 01 842 4833

We offer a technical advisory service on the telephone:

RING 0844 879 3588 (UK) or 01 842 4833 (R.O.I)

GUARANTEE AND CONTACT DETAILS

(A4) Leaflet No. 581-2143-08a

GUARANTEE

Terms and Conditions for UK (outside UK contact your local distributor)

In the unlikely event of a product breakdown during the guarantee period you should

contact our Service and Repair Helpline who will be able to assist with the repair and

advise of the best course of action to be taken.

Please DO NOT remove the product prior to making this call as this may invalidate your

guarantee.

Service and Repair Tel: 0844 879 3588 (UK) or 01 842 4833 (R.O.I)

We guarantee this product for a period of 12 months from the date of purchase.

Within the guarantee period we will resolve, free of charge, any manufacturing defects in the product

resulting from faulty workmanship or material on condition that:-

a) The product has been correctly installed and commissioned in accordance with our instructions and

is being used on the supply circuit or voltage printed on the rating plate.

b) The product has been used in accordance with these instructions and has not been tampered with

or otherwise subject to misuse, neglect or accident.

c) The product has not been taken apart, modified or repaired except by a person authorised by us.

d) Evidence of the date of purchase in the form of an invoice or receipt will be required in order to

qualify under the terms of this guarantee.

e) For the service work to be undertaken free of charge, the work must only be undertaken by us,

or our approved agents.

f) Service under guarantee has no effect on the expiry date.

The guarantee on any exchanged parts or product ends when the original guarantee period ends.

EXCLUSIONS

This guarantee DOES NOT cover damage or defects arising from poor or incorrect installation,

improper use or lack of maintenance.

It is the responsibility of the installer to check that the installation parameters meet the requirements

of the products, and any relevant regulations.

If we are called out to a fault, which is subsequently identified as being an installation fault, we will

make a charge, it is important that the routine checks are completed before calling us out, as many

issues can be simply diagnosed and resolved.

A charge will be made where a call under the terms of the guarantee has been booked and a failure

was not product related, or an engineer arrives and is not able to gain access.

We make no guarantees as to response time for repairs.

We will endeavour to achieve the most timely response possible but while we indicate an average

response time, this should not be taken as a guarantee.

The guarantee applies to a repair or replacement (at our discretion) of the product subject to the

conditions above, and DOES NOT cover compensation for the loss of the product or consequential

loss of any kind.

This guarantee does not apply to the repair or replacement of accessories, isolating switches,

electrical cable, fuses and/or circuit breakers.

This

uarantee does not affect

our statutor

hts.

INSTALLATION INSTRUCTIONS

Model 50816401

INTRODUCTION

THIS HEATER IS NOT EQUIPPED WITH A DEVICE TO CONTROL THE

ROOM TEMPERATURE. DO NOT USE THIS HEATER IN SMALL ROOMS

WHEN THEY ARE OCCUPIED BY PERSONS NOT CAPABLE OF LEAVING

THE ROOM ON THEIR OWN, UNLESS CONSTANT SUPERVISION IS

PROVIDED.

CHILDREN LESS THAN 8 YEARS OLD SHOULD BE KEPT AWAY FOR

THE APPLIANCE UNLESS CONTINUALLY SUPERVISED.

THIS APPLIANCE CAN BE USED BY CHILDREN AGED FROM 8 YEARS

AND ABOVE AND PERSONS WITH REDUCED PHYSICAL, SENSORY OR

MENTAL CAPABILITIES, OR LACK OF EXPERIENCE AND KNOWLEDGE

IF THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION

CONCERNING USE OF THE APPLIANCE IN A SAFE WAY AND

UNDERSTAND THE HAZARDS INVOLVED.

CHILDREN SHALL NOT PLAY WITH THE APPLIANCE.

CLEANING AND USER MAINTENANCE SHALL NOT BE MADE BY

CHILDREN.

Thank you for purchasing a quality

Creda Sunfan Heater

manufactured in England.

Please take time to read this manual thoroughly to familiarise yourself with all

instructions, BEFORE beginning installation.

ALL WIRING AND INSTALLATION MUST BE SUPERVISED BY A SUITABLY

QUALIFIED PERSON.

The heater is intended for connection to fixed wiring.

Installation and wiring must be in accordance with the current edition of BS.7671

(the ‘IET Wiring Regulations’) in force at the time of installation.

Installations outside England and Wales must also conform to any local or

appropriate regulations in effect.

The protective fuse rating must NOT exceed 15A and a means for disconnection in

all poles MUST BE incorporated in the fixed wiring in accordance with the Wiring

Regulations.

This heater is intended for high level wall mounting in industrial/commercial

premises. However, it should NOT be used in corrosive atmospheres.

The heater should be fixed to a wall at a minimum height of 1.8m and there MUST

be a minimum gap of 150mm between the top of the heater and the ceiling.

Therefore the heater should NOT be installed in areas where the ceiling height is

less than 2.3m.

As a general rule, fan heating is NOT recommended for rooms greater than 5.0m

high. 7

9. The arm cover can now be replaced and retained with the two screws (see Diagram 2.0).

10. The

Sunfan Heater

should now be run to establish that it is working correctly and that it

is correctly aligned.

Should the heater require re-alignment, repeat section (8) & (9).

NOTE:- IF THE LOCKING SCREW IS NOT TOO TIGHT A SMALL AMOUNT OF

ADJUSTMENT SHOULD BE POSSIBLE WITHOUT REPEATING SECTIONS (8) & (9).

DCS Dual Remote Control Switch (Hot/Cold) Catalogue No. 82815906

Additional accessories and spare parts can be supplied by your local Creda distributor,

or on our website www.credaheating.co.uk

SCHEMATIC WIRING DIAGRAM

ADDITIONAL ACCESSORIES

The back nut on the cable gland should now be fully tightened to secure the supply

cable.

The terminal marked “L1” is required only if the hot/cold option is taken.

This will require a separate remotely mounted

“DCS Remote Dual Control Switch

(Catalogue No. 82815906)”

available from your local electrical wholesaler or distributor.

Wiring instructions are supplied with the control switch, and as one of the internal

connections in the

Sunfan Heater

will require re-location, this work should only be carried

out by a competent electrician.

8. The

Sunfan Heater

can now be pointed in the required direction by slackening the locking

screw, aligning the heater and re-tightening the locking screw (see Diagram 2.6).

WARNING:

DO NOT SWITCH THE HEATER ON BEFORE REPLACING THE ARM

COVER.

PROTECTION

If the heater is to be installed near an adjacent wall, the heater should be parallel

to, or angled away from it, and there should be a minimum gap of 300mm

between the adjacent wall and any part of the heater (see Diagram 1.0).

The heater MUST NOT be mounted immediately below a fixed electrical socket

outlet, neither should it be directed at any surface nearer than 1.5m.

This heater is protected by two thermal cut-outs.

TC1 being factory re-settable will operate only in the event of a major problem such as fan

blades being stalled.

TC2 is a cyclic device and will protect the heater in the event of the airflow being obstructed.

TC2 will reset when the fault condition has been rectified.

This heater is designed for a long, maintenance free, service life.

The motor is fully enclosed and should require no attention. However, if the heater is

located in a very dusty environment, it is recommended that any build-up of debris is

removed periodically.

MAINTENANCE

1. Remove the two screws from the arm cover.

Remove the arm cover (see Diagram 2.0).

2. Pull the wall plate down and away.

3. Return the

Sunfan Heater

to its box for safe

keeping, retaining the wall plate.

4. Use the wall plate as a template to mark out, drill and wall plug the three fixing holes.

See Diagram 1.0 for minimum clearance from floor, walls and ceiling.

Make sure that the wall plate is vertical.

Note:

The heater will accept cable entry from the top, bottom or rear.

If the rear cable entry is to be used, the cable gland can be discarded.

If either top or bottom entry is required use a knife or similar sharp tool to remove the

thin web of material in the threaded part of the appropriate end of the wall plate.

Alternatively, the gland can be screwed into the required end and tightened with an

appropriate spanner which will result in the thin web of material being removed.

5. Offer the wall plate to the wall and attach with TWO No.10 x 1.5” (or longer) round head

screws in holes A and B only.

DO NOT fix screw in hole C at this stage (see Diagram 2.3).

INSTALLING THE HEATER

6. With the wall plate firmly attached to the wall, latch the heater to the wall plate by

pushing back and down. Secure the heater to the wall/wall plate using a third

No.10 x 1.5” (or longer) round head screw through hole C (see Diagram 2.4).

7. Make sure the mains electricity supply is off.

The

Sunfan Heater

can now be connected to a suitable single-phase electrical supply

using appropriate cable.

If either top or bottom cable entry is required, fit the cable gland in the appropriate

threaded end of the wall plate.

If rear cable entry is required, the cables should project through the hole at the lower

edge of the wall plate.

Pass the twin cable through the cable gland and connect the brown insulated cable to the

terminal marked “L” on the terminal block.

Connect the blue insulated cable to the terminal marked “N” on the terminal block (see

Diagram 2.5).

WARNING:

IT IS MOST IMPORTANT TO ENSURE THAT THE SCREWS IN THE

TERMINAL BLOCK ARE FULLY TIGHTENED.

FAILURE TO DO SO COULD RESULT IN THE CONNECTION

OVERHEATING AND CAUSE DAMAGE TO THE APPLIANCE.

Creda SF3 Installation guide

Brand: Creda

Model: SF3

Category: Space heaters

Type: Installation guide

Download PDF

report

Creda SF3 Installation guide

Creda SF3 Installation guide

Related papers

Other documents