Sharp AQUOS LC-46LE820UN Operating instructions

Brand: Sharp

Model: AQUOS LC-46LE820UN

Category: LCD TVs

Type: Operating instructions

This manual is also suitable for

SHARP

AQUOS

LC-40LE820UN

LC-46LE820UN

LC-52LE820UN

LC--60LE820UN

LiQUiD

Ti_Li_Vl

| DOLBY

DIGITAL{

H _:::lINll|TM

HIGH-DEFINITION MULTIMEDIA INTERFACE

1245

NYCE

IMPORTANT • Please read this operation manual before starting operating the equipment.

IMPORTANT • Veuillez lire ce mode d'emploi avant de commencer b.utiliser I'appareil.

IMPORTANTE • Lea este manual de operaci6n antes de comenzar a operar el equipo.

LC-40LE820U

LC-46LE820U

LC-52LE820U

LC-60LE820U

LiQUiD CRYSTAL TELEViSiON

ENGLISH

OPERATION MANUAL

IMPORTANT:

To aid reporting in case of loss or theft, please record the

TV's model and serial numbers in the space provided. The

numbers are located at the rear of the TV.

Model No.:

Serial No.:

iMPORTANT INFORMATION

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

RISK OF ELECTRICSHOCK

DO NOTOPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrow-head

symbol, within an equilateral triangle,

is intended to alert the user to the

presence of uninsulated "dangerous

voltage" within the product's

enclosure that may be of sufficient

magnitude to constitute a risk of

electric shock to persons.

The exclamation point within a

triangle is intended to alert the user

to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the product.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

Q-1

iMPORTANT iNFORMATiON

WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly

approved by the manufacturer could void the user's authority to operate this equipment.

CAUTION:

This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other

equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded

cables and connectors for connections.

DECLARATION OF CONFORMITY:

SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-40LE820UN/LC-46LE820UN/LC-52LE820UN/LC-60LE820UN

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

RESPONSIBLEPARTY:

SHARPELECTRONICSCORPORATION

Sharp Plaza, Mahwah, New Jersey07495-1163

TEL: 1-800-BE-SHARP

For BusinessCustomers: URLhttp://www.sharpusa.com

INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

"Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National

Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of cable entry as practical."

This product qualifies for ENERGY STAR when "Home" is selected for "TV Location".

Setting "TV Location" to "Home" allows the TV to achieve an energy-saving status for household use.

Trademarks

* Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby

Laboratories.

* "HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI

Licensing LLC."

* Products that have earned the ENERGY STAR_>are designed to protect the environment through superior energy

efficiency.

* L C "J ;¢ 71'I-, L C F O N T, _T.)b'_'--C 7_ _' t'-and LC logo mark are registered trademarks of SHARP Corporation.

This product is embedded with LC Font technology, which was developed by SHARP Corporation for clearly

displaying easy-to-read characters on LCD screens. However, other fonts are used for some screen pages, too.

* "x.v.Color" and x.v.Co_or are trademarks of Sony Corporation.

* Netflix and the Netflix logo are the registered trademarks of Netflix, Inc.

Q-2

DEAR SHARP CUSTOMER

Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years

of trouble-free operation of your product, please read the important Safety instructions carefully before

using this product.

iMPORTANT SAFETY iNSTRUCTiONS

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage

if improperly handled. This product has been engineered and manufactured with the highest priority on safety.

However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please

observe the following instructions when installing, operating and cleaning the product. To ensure your safety

and prolong the service life of your Liquid Crystal Television, please read the following precautions carefully

before using the product.

lo)

11)

12)

13)

14)

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The

wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

Only use attachments/accessories specified by the manufacturer.

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate

normally, or has been dropped.

Additional Safety Information

15) Power Sources-This product should be operated only from the type of power source indicated on the

marking label. If you are not sure of the type of power supply to your home, consult your product dealer or

local power company. For products intended to operate from battery power, or other sources, refer to the

operating instructions.

16) Overloading- Do not overload wall outlets, extension cords, or integral convenience receptacles as this

can result in a risk of fire or electric shock.

17) Object and Liquid Entry- Never push objects of any kind into this product through openings as they may

touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill

liquid of any kind on the product.

18) Damage Requiring Service-Unplug this product from the wall outlet and refer servicing to qualified

service personnel under the following conditions:

a) When the AC cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the product,

c) If the product has been exposed to rain or water,

d) If the product does not operate normally by following the operating instructions.

Adjust only those controls that are covered by the operating instructions as an improper adjustment

of other controls may result in damage and will often require extensive work by a qualified technician

to restore the product to its normal operation,

e) If the product has been dropped or damaged in any way, and

f) When the product exhibits a distinct change in performance - this indicates a need for service.

19) Replacement Parts-When replacement parts are required, be sure the service technician has used

replacement parts specified by the manufacturer or have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock, or other hazards.

20) Safety Check-Upon completion of any service or repairs to this product, ask the service technician to

perform safety checks to determine that the product is in proper operating condition.

21) Wall or ceiling mounting-When mounting the product on a wall or ceiling, be sure to install the product

according to the method recommended by the manufacturer.

Q-3

iMPORTANT SAFETY iNSTRUCTiONS

Outdoor Antenna Grounding - If an outside antenna is

connected to the television equipment, be sure the antenna

system is grounded so as to provide some protection against

voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA 70,

provides information with regard to proper grounding of the

mast and supporting structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding conductors,

location of antenna-discharge unit, connection to grounding

electrodes, and requirements for the grounding electrode.

EXAMPLE OFANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE ANSI/NFPA 70

_:_- ANTENNA

LEADINWIRE

ANTENNA

/", LLI NX DISCHARGEUNIT

-"i_....f:./NECSECTION810-20/

1"IGRO NO,NG

J ONDUCTORS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC -- NATIONAL ELECTRICAL CODE

• Water and Moisture -- Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a swimming pool; and the like.

Stand -- Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base

can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart,

stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product

on a wall, be sure to follow the manufacturer's instructions. Use only the mounting hardware recommended by the

manufacturer.

Selecting the location -- Select a place with no direct sunlight and good ventilation.

Ventilation -- The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents

and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place

the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not

designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper

ventilation is provided or the manufacturer's instructions are followed.

The Liquid Crystal panel used in this product is made of glass. Therefore, it can break when the product is dropped or

applied with impact. Be careful not to be injured by broken glass pieces in case the panel breaks.

Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

The Liquid Crystal panel is a very high technology product with 2,073,600 pixels, giving you fine picture details.

Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that

this does not affect the performance of your product.

Lightning - For added protection for this television equipment during a lightning store% or when it is left unattended and

unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to

the equipment due to lightning and power-line surges.

Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric

light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,

extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

To prevent fire, never place any type of candle or flames on the top or near the TV set.

To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items.

Do not display a still picture for a long time, as this could cause an afterimage to remain.

To prevent fire or shock hazard, do not expose this product to dripping or splashing.

No objects filled with liquids, such as vases, should be placed on the product.

Do not insert foreign objects into the product. Inserting objects in the air vents or other openings may

result in fire or electric shock. Exercise special caution when using the product around children.

Precautions when transporting the TV

When transporting the TV, never carry it by holding or otherwise putting pressure onto the display. Be sure to always

,_ carry the TV by two peoPle ho!d!ng it w!th two hands -- one hand on each side of the TV; _._

Caring for the Cabinet

Use a soft cloth (cotton, flannel, etc.) and gently wipe the surface of the cabinet.

Using a chemical cloth (wet/dry sheet type cloth, etc.) may deform the components of the main unit cabinet or cause

cracking.

Wiping with a hard cloth or using strong force may scratch the surface of the cabinet.

Ifthe cabinet is very dirty, wipe with a soft cloth (cotton, flannel, etc.) soaked in neutral detergent diluted with water and

thoroughly wrung out, and then wipe with a soft dry cloth.

The cabinet is primarily made of plastic. Avoid using benzene, thinner, and other solvents, as these may deform the

cabinet and cause the paint to peel off.

Do not apply insecticides or other volatile liquids.

Also, do not allow the cabinet to remain in contact with rubber or vinyl products for a long period of time. Plasticizers

_ !nsidethep!asticmay causethe cab!nettodeformandcausethepa!nttopee! off. j

@-4

iMPORTANT SAFETY iNSTRUCTiONS

F-

Caring for the Liquid Crystal panel

• Turn off the main power and unplug the AC cord from the wall outlet before handling.

Gently wipe the surface of the display panel with a soft cloth (cotton, flannel, etc.).

To protect the display panel, do not use a dirty cloth, liquid cleaners, or a chemical cloth (wet/

dry sheet type cloth, etc.). This may damage the surface of the display panel.

Wiping with a hard cloth or using strong force may scratch the surface of the display panel.

Use a soft damp cloth to gently wipe the display panel when it is really dirty.

(It may scratch the surface of the display panel when wiped strongly.)

Ifthe display panel is dusty, use an anti-static brush, which is commercially available, to clean it.

To avoid scratching the frame or screen, please use a soft, lint free cloth for cleaning. Approved cleaning cloths are

available directly from Sharp in single (00Z-LCD-CLOTH) or triple (00Z-LCD-CLOTH-3) packs. Call 1-800-BE-SHARP for

ordering, or VISIT http://www.sharpusa.com/SharpDirect.

Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind:

THE ISSUE

o The home theater entertainment experience is a growing trend and larger flat panel displays

are popular purchases. However, flat panel displays are not always supported on the proper

stands or installed according to the manufacturer's recommendations.

o Flat panel displays that are inappropriately situated on dressers, bookcases, shelves, desks,

speakers, chests or carts may fall over and cause injury.

THIS MANUFACTURER CARES!

o The consumer electronics industry is committed to making home entertainment enjoyable

and safe.

TUNE INTO SAFETY

o One size does NOT fit all. Follow the manufacturer's recommendations for the safe installation

and use of your flat panel display.

o Carefully read and understand all enclosed instructions for proper use of this product.

o Don't allow children to climb on or play with furniture and television sets.

o Don't place flat panel displays on furniture that can easily be used as steps, such as a chest

of drawers.

o Remember that children can become excited while watching a program, especially on a

"larger than life" flat panel display. Care should be taken to place or install the display where it

cannot be pushed, pulled over, or knocked down.

o Care should be taken to route all cords and cables connected to the flat panel display so that

they cannot be pulled or grabbed by curious children.

WALL MOUNTING: IF YOU DECIDE TO WALL MOUNT YOUR FLAT PANEL DISPLAY, ALWAYS:

o Use a mount that has been recommended by the display manufacturer and/or listed by an independent laboratory (such

as UL, CSA, ETL).

o Follow all instructions supplied by the display and wall mount manufacturers.

o Ifyou have any doubts about your ability to safely install your flat panel display, contact your retailer about professional

installation.

o Make sure that the wall where you are mounting the display is appropriate. Some wall mounts are not designed to be

mounted to walls with steel studs or old cinder block construction. Ifyou are unsure, contact a professional installer.

• A minimum of two people are required for installation. Flat panel displays can be heavy.

Note: CEA is the preeminent trade association promoting growth in the $161 billion

C_ U.S. consumer electronics industry. More than 2,200 companies enjoy the benefits of

CEA membership, including legislative advocacy, market research, technical training and

Consumer Electror_ A_sociation

WWW,,_F Of_/$a_et _ education, industrypromotion and the fostering of business and strategic relationships.

Q-5

Contents

iMPORTANT iNFORMATiON ..................... 1

Trademarks ....................................... 2

DEAR SHARP CUSTOMER ....................... 3

iMPORTANT SAFETY iNSTRUCTiONS ........ 3=5

Supplied Accessories ............................ 7

QUICK REFERENCE

Attaching the Stand ............................ 7

QUICK INSTALLATION TIPS ................... 8

Using the Remote Control Unit ................. 8

Preparation

Antennas ....................................... 9

Installing Batteries in the Remote Control Unit... 9

Part Names

TV (Front) ..................................... 10

TV (Rear)...................................... 10

Remote Control Unit ........................... 11

Introduction to Connections

Experiencing HD Images ...................... 12

Types of Connection .......................... 12

Displaying an External Equipment Image ....... 12

Connecting to External Equipment

Connecting a Blu-ray Disc/DVD Player or

HD Cable/Satellite Set-top Box ........... 13-14

Connecting a VCR, Game Console,

Camcorder or Cable/Satellite Set-top Box .... 14

Connecting an Audio Amplifier ................. 15

Connecting a PC .............................. 16

Watching TV

Turning On/Off the Power ..................... 17

Initial Installation ............................... 17

Direct

Button Operation

Changing Channels ....................... 18

Changing Volume .......................... 18

MUTE ...................................... 18

Sleep Timer ................................ 18

FLASHBACK ............................... 18

SURROUND ............................... 18

FREEZE.................................... 18

INPUT...................................... 19

AV MODE .................................. 19

AUDIO ..................................... 19

DOCK ...................................... 20

POWER SAVING ........................... 20

Closed Captions and

Digital Closed Captions ................... 20

VIEW MODE ............................... 21

On-Screen Display Menu

On-Screen Display Menu Operation ........... 22

Menu Operation Buttons ...................... 22

Menu Items ................................... 23

Picture Settings ............................ 24-25

Audio Settings ................................ 26

Power Control ................................. 27

System Options ............................ 28-30

Initial Setup ................................. 30-33

Information ................................. 34-36

Enjoying Photo and Music Playback

Viewing Photos and Listening to Music ........ 37

Photo Mode ................................ 38-39

Music Mode ................................... 40

USB Memory Device Compatibility ............. 40

Other Viewing Options

Presetting Remote Control Function ........... 41

Operating the Connected Equipment ....... 41-42

Using AQUOS LINK

Controlling HDMI Equipment

Using AQUOS LINK ....................... 43-45

Link Operation Menu ....................... 45-46

Using a PC

Displaying a PC Image on the Screen .......... 47

Adjusting the PC Image ....................... 48

Setting Audio Input ............................ 48

PC Compatibility Chart ........................ 48

RS-232C Port Specifications .................. 49

Using the Intemet

Internet Setup .............................. 50-51

Displaying Updated Information and

Support Service ............................. 51

Entering Text (Software Keyboard) ............. 52

Using the Browser .......................... 53-56

Instantly Watching Movies from Netflix ...... 57-59

Appendix

Removing the Stand ........................... 60

Setting the TV on the Wall ..................... 61

Troubleshooting ............................ 62-63

Troubleshooting - Error Message .............. 63

Specifications .............................. 64-65

Optional Accessory ............................ 65

Information on the Software License for

This Product ................................. 66

Calling for Service ............................... 67

LIMITED WARRANTY ............................ 67

Dimensional Drawings

o The dimensional drawings for the LCD TV set are shown

on the inside back cover.

Q-6

Supplied Accessories

Make sure the following accessories are provided with the product.

LC-40LE820UN/

LC-46LE820UN/

LC-52LE820UN

Remote control unit "AAA" size battery Cable clamp Stand unit Operation manual

(x 1) (x 2) (x 1) (x 1) (x 1)

Page 8 Page 9 Page 8 Page 7

[] Connection guide (x 1)

Always use the AC cord supplied with the TV.

The illustrations above are for explanation purposes and may vary slightly from the actual accessories.

QUICK REFERENCE

o Before attaching (or detaching) the stand, unplug the AC cord.

o Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged.

o Attach the stand in the correct direction.

o Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.

o Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.

Confirm that there are 9 screws (5 short screws

and 4 long screws) supplied with the stand unit.

Attach the supporting post for the stand unit onto

the base using the box for the stand unit as shown

below.

o The supporting post attaches to the base at an off-

centered location on the base. Be sure to attach the

supporting post in the direction indicated below and

attach the stand to the TV with the wider side of the

base facing forward.

_4_ _11_ Long ......

4 Insert and tighten the 4 screws into the 4 holes on

the rear of the stand unit.

_ Short screws

' A

II II

5 (i_ Insert the stand cover.

(9 Insert the screw to secure the stand cover.

Short screw -illi--_! _ (_

3 Insert the stand into the openings on the rear of the

TV.

Soft cushion

To detach the stand, perform the steps in reverse

order.

Q-7

QUICK REFERENCE

1 Attach your antenna to the back of the television.

(See page 9.)

2 Connect the AC plug for the television into the AC

outlet.

Place the TV close to the AC outlet, and keep the power

plug within reach.

,, TO PREVENT RiSK OF ELECTRIC SHOCK, DO NOT

TOUCH UN-INSULATED PARTS OFANY CABLES

WiTH THE AC CORD CONNECTED.

3 Bundle the cords properly with the cable clamp.

When turning on the TV for the first time, press

POWER on the touch sensor panel on the front of

the TV.

Use the remote control unit by pointing it towards the

remote control sensor on the TV. Objects between the

remote control unit and the remote control sensor may

prevent proper operation.

Remote control sensor 1300

30° 30°

30°

17" (5 m)

Cautions regarding the remote control unit

o Do not expose the remote control unit to shock. In addition,

do not expose the remote control unit to liquids, and do not

place in an area with high humidity.

o Do not install or place the remote control unit under direct

sunlight. The heat may cause deformation of the remote

control unit.

The remote control unit may not work properly if the remote

control sensor on the TV is under direct sunlight or strong

lighting. In such cases, change the angle of the lighting

or the TV, or operate the remote control unit closer to the

remote control sensor.

iMPORTANT:

IFTHE UNIT DOES NOT POWER ON - UNPLUG THE

TELEVISION FROM THE OUTLET AND REPEAT THE

INSTALLATION STEPS.

IFYOU STILL ENCOUNTER NO POWER, PLEASE CONTACT

US AT 1-800-BE-SHARP.

POWER

5 Insert the batteries into the remote control unit. (See

page 9.)

Speakers cannot be detached from the TV.

The TV can be rotated up to 20 degrees to right and left.

Q-8

Preparation

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections

that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector,

plug it into the antenna terminal at the rear of the TV set. For connecting the antenna cable to the TV, use

commercially available cables.

Connecting Antenna Cable

+ Connect the antenna cable to the TV using one of the methods in the illustration as shown ((_, (_, (_ or (_).

Home Antenna

(_ Cable without a CATV CableTV lead-In terminal(75-ohm)

1.A 75-ohm system is generally a round cable with F-type connector

that can easily be attached to a terminal without tools.

2.A 300-ohm system is a flat "twin-lead" cable that can be attached

to a 75-ohm terminal through a 300/75-ohm adapter.

_F-type connector

75-ohm coaxial cable (round)

300-ohm twin-lead cable (flat)

F=type connector should be finger=tightened only.

.....%//_, _,_ F-type connector

When connecting the RF cable to the TV set, do not tighten F-type i_;i_sf_ _

connector with tools. _/ x/ ,_.__

If tools are used, it may cause damage to your TV set. (The breaking <

_! in!ema! ci!cuit: etc') _5:th m c°axia! _ab!e

If the remote control fails to operate TV functions, replace the batteries in the remote control unit.

1 Open the battery cover. 2 Insert two "AAA" size batteries (supplied with 3 Close the battery cover.

the product).

+ Place the batteries

with their terminals

corresponding to the (+)

and (-) indications in the

battery compartment.

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.

+ Do not mix batteries of different types. Different types of batteries have different characteristics.

+ Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage

in old batteries.

+ Remove batteries as soon as they are worn out. Chemicals that leak from batteries that come in contact with skin can cause a

rash. Ifyou find any chemical leakage, wipe thoroughly with a cloth.

+ The batteries supplied with this product may have a shorter life expectancy due to storage conditions.

+ Ifyou will not be using the remote control unit for an extended period of time, remove batteries from it.

Q-9

Part Names

Center Icon il .............[_'J

Remote control sensor

VOL-/+ I INPUT I POWER 2

CHV/A MENU

OPC sensor "1

(See page 24.)

"10PC: Optical Picture Control

*2 See pages 17 and 22 for using the touch sensor panel.

INPUT 1 terminals

"1 See pages 12 to 16 and 43 for external equipment connection.

*2 See page 48 for details on the Audio Select function.

us_ _ USE} 1 terminal

ETHERNET terminal

I ® AUO_OOUTl_AUDIO OUT terminal

_ INPUT 2 terminal

_ INPUT 3 terminal (PC-IN)

AUDIO,._AUDIO IN terminal

(shared for INPUT 3 and INPUT 4) *2

_ INPUT 4 terminal (HDMI)

ARC: Audio Return Channel

INPUT 5 terminal (HDMI)

INPUT 6 terminal (HDMI)

INPUT 7 terminal (HDMI)

DIGITAL l

Auo_o_ DIGITAL AUDIO OUTPUT terminal

us_2_ USB 2 terminal

The illustrations in this operation manual are for explanation purposes and may vary slightly from the actual operations.

The examples used throughout this manual are based on the LC-52LE820UN model.

Q-10

Part Names

_-||e " e| e | T 1

POWER: Switch the FV power on or enter standby. (See page

17.)

TV, STB, DVDoVCR, AUDIO: Switches the remole control for

TV, SIB, DVD, BD, VCR and AUDIO operation. (See pages 41 to

42 for details.)

* To enter the code registration mode, you need to press an

appropriate button (STB, DVD=VCR or AUDIO) and DISPLAY

at the same time.

External equipment operational buttons: Operate the external

equipment,

OPTION: Display the LJnkOperation Menu screen, This button

will functbn only when AQUOS LINK is used, (See pages 43 b 46

for details`)

SLEEP: Set the sleep timer. (See page 18.)

0----9:Set the channel. (See page 18.)

._(DOT}: (See pages 18 and 41`)

CC: Display captbns from a closed-caption source. (See page 20.)

AV MODE: Select an audio or video setting. (See page 19,)

MUTE: Mute the sound. (See page 18,)

VOL+/-: Set the volume. (See page 18.)

MENU: Display the menu screen. (See page 22.)

AQUOS NET: Switches the display to the Sidebar Widget,

TV +Web, Web or R/screen. (See pages 50 to 58 br details.)

,I,/V/41/iI_, ENTER: Select a desired item on the screen.

EXIT: lum off fl-le menu screen.

SU RROU ND: Select Surround settings. (See page 18`)

FAVORITE CH: Set the favorite channels. (See page 31.)

A, B, C, D: Select 4 preset favorite channels in 4 diff_rent

categories. (See page 31,)

While watching, you can toggle the selected channels by pressing

A, B, C and D.

DISPLAY: Display the channel inforrnation.

POWER (SOURCE}: Turns the power of the external equipment

on and off.

REC STOP: Stops one touch recording. This button will function

only when AQUOS UNK is used. (See pages 43 to 45 for details

POWER SAVING: Select Power Saving setlings. (See page 20`)

ENT: Jumps to a channel after selecting with the (1--9 buttons.

FLASHBACK: Return to the previous channel or extemal input

mode. (See page 18`)

VIEW MODE: Select the screen size. (See pages 21,47 and 59

INPUT: Select a R/input source. (l_/, INPUT 1, INPUT 2, INPUT 3,

INPUT 4, INPUT 5, INPUT 6, INPUT 7) (See pages 12 and 19.)

CN/X,/V: Select the channel, (See page 18,)

DOCK: Display the DOCK, (See page 20`)

RETURN: Retum tothe previous menu screen.

AUDIO: Selects the MTS/SAP or the audio mode during multi-

channel audio broadcasts. (See page 19`)

FREEZE: Set the still image. Press again to retum to normal

screen. (See page 18.)

• When using the remote control unit, point it at the TV.

@-11

introduction to Connections

An HDTV without an HD source is just an ordinary TV.

To enjoy HD images on the TV, you should get HD programming from the following:

• Over-the-air broadcasting via HD quality antenna

• HD cable/satellite subscription

HD compatible external equipment

o Forinformationon updatingto HDprogramming, askyourcable/satelliteserviceprovider.

Image quality differs depending on the terminal used. To enjoy clearer images, check the output terminals of your

external equipment and use its appropriate terminals for higher quality images.

o The illustrationsofthe terminalsareforexplanationpurposesand mayvary slightlyfrom the actual products.

Quality H_rn_ _ HDMI-certified cable

lab

AUDIO

DVI OUT

O3.5mmstereominijackcable _ I ® ....... I

DVI-HDMIconversion cable _ I _ H_

_ _ _._ Component video cable _ [ _ _o_,__ _ _

COMPONENT

R_AUO,O_L Audio cable _[ _-_._,,_,hi

,,_Page 13

,,_Page 14

Standard _ R_ _L AV cable _

Quality V,DEO AMO,O _=_ (AV r!!!! p!ug and RCA p!ugs) _ _, Page 14

To view external source images, select the input source by pressing INPUT on the remote control unit or on the TV.

Example 1 Press INPUT.

* The CH List screen displays.

2 Press A/T to select the input source.

You can also select the input source by pressing

INPUT. Each time INPUT is pressed, the input source

toggles.

INPUT1 ,_ INPUT2 ,_ INPUT3

t ,l

TV * INPUT4

iNPUT

AQUOS

NET DOCK

An image from the selected source automatically

displays.

If the corresponding input is not plugged in, you

cannot change the input. Be sure to connect the

equipment beforehand.

Q-12

Connecting to E×ternal Equipment

You can connect many types of external equipment to your TV. To view external source images, select the input

source from INPUT on the remote control unit or on the TV. (See pages 12 and 19.)

For connecting the TV to external equipment, use commercially available cables.

To protect equipment, always turn off the TV before connecting any external equipment.

Please read the relevant operation manual (Blu-ray disc player, etc.) carefully before making connections.

When using HDMI cable (INPUT 4, 5, 6 or 7}='

The HDMI (High Definition Multimedia Interface) terminal is an audio-video interface that enables a connection for audio and

video signals using a single cable. The HDMI tern_inal supports high-resolution video input.

HDMI-certified cable

= Blu-ray disc player ,, DVD player

o HD cable/satellite set-top box

To enjoy 1080p display capability, connect your external equipment using an HDMI-certified cable or a component cable and

set the equipment to 1080p output.

Supported Audio format: Linear PCM, sampling rate 32/44.1/48kHz.

When you connect external equipment using a DVI-HDMI conversion cable or when you connect ARC-compatible

equipment, use INPUT 4.

m When using DVI=HDMI conversion cable (iNPUT 4}="

= Blu-ray disc player • DVD player

o HD cable/satellite set-top box

DVI-HDMI conversion cable

Back panel

vertical inputs

When using a DVI-HDMI conversion cable, you should make an analog audio connection. In this case, in addition to

connecting a DVI-HDMI conversion cable to the INPUT 4 (HDMI) terminal, connect a © 3.5 mm stereo minijack cable to the

AUDIO IN terminal and set "Audio Select" to "HDMl÷Analog". (See page 48.)

Q-13

Connecting to External Equipment

[] When using Component cable (iNPUT 1):

BID-ray disc player • DVD player

HD cable/satellite set-top box

Audio cable

Component video cable

AUDIO-R (Red)

AUDIO-L (White)

Back panel

horizontal inputs

To enjoy 1080p display capability, connect your external equipment using an HDMI-certified cable or a component cable and

set the equipment to 1080p output.

See page 13 for connecting a BID-ray disc player, DVD player or an HD cable/satellite set-top box to the HDMI terminal.

[] When using Composite cable (INPUT 2):

=Game console = VCR

Camcorder • Cable/Satellite set-top box

Back panel

vertical inputs

/ ...........

/¸ ,_, A_;_{_ _; i_

/ •

AV cable (AV mini plug and RCA plugs)

: i,lt>

' :;

• For the AV cable to connect to the INPUT 2 terminal, use a plug described below.

!_!!i_i_ii!_!_!ii_ii!i_i!_ii_i_iii_i!_i_!!i!i!!_!!i_!_!_!_!!_!ii!i_i_!_!_!_!i;!_i_i_:;_i__!iiii!_!i_!_!i_!_!_i_i_iii_i_i_iii_i_i_i_iii_i_i_i_ii_!_!_i_!!_!!_i!iiii_!_i!_i_i_i!_:_!_i_i!_!i_i_i_!i_ii_!i_i_!_!_!i_i!_!i_i_i!i!iii!!i!i_i_i_i_i!_!!_!!_i_!i_i_!_i_i!i!i!!i!ili_i_i_i_i!_!!_!!_i_!i_i_i_i_i_i_iiii:i;_i!_ii_!_il!_ii_i_!:ii!!i!i_!'iiJiii!iiiii!i!_!ii_i!_!!i_!!iiii_!i!iii__!i!iii_i_iiii__iiiiii_i_iii_i_iii_i_iii_ili_ii_ii_ii:_

1 AUDIO (LEFT)

2 Composite Video

3 A&V Ground (EARTH)

4 AUDIO (RIGHT)

Q-14

Connecting to E×temal Equipment

II When using optical fiber cable:

It is possible to output audio through the DIGITAL AUDIO OUTPUT terminal. (See page 28 for details.) PCM audio

outputs from the terminal.

Back panel

vertical inputs

Optical fiber cable

AUDIO

OUTPUT

Depending on the connected equipment, audio will not output from the DIGITAL AUDIO OUTPUT terminal in HDMI

connection. In this case, set the audio formats of the connected equipment to PCM, 32/44.1/48 kHz.

When using audio cable:

Back panel

vertical inputs

Audio cable

/ h

i :!!!!!!!2ilmZ!!.

i!!ii .................

, i;

See page 29 for details on the Output Select function.

Q-15

Connecting to External Equipment

Refer to page 48 for a list of PC signals compatible with the TV.

When using HDMI cable (iNPUT 4, 5, 6 or 7}:

HDMI-certified cable

Back panel

vertical inputs

[_ HORtt|

iD.om,

D HOrn|

Depending on the board, only video signals may be output. In this case, in addition to connecting an HDMI-certified cable to

"HDMl+Analog". (See page 48.)

• The HDMI terminals only support digital signal.

m When using DVI=HDMI conversion cable (iNPUT 4}:

t__ ® 3.5 mm stereo minijack cable

/_.__ _ DVI-HDMI conversion cab_,

Back panel

vertical inputs

'_ _ AUDIO IN

When using a DVI-HDMI conversion cable, you should make an analog audio connection. In this case, in addition to

connecting a DVI-HDMI conversion cable to the INPUT 4 (HDMI) terminal, connect a G 3.5 mm stereo minijack cable to the

AUDIO IN terminal and set "Audio Select" to "HDMl+Analog". (See page 48.)

m When using analog RGB cable (iNPUT 3}:

Back panel

vertical inputs

Analog RGB cable

(D-sub 15-pin cable or VGA cable)

'_ (_ AUDIO IN

When using an analog RGB cable, input the audio signal to the AUDIO IN temqnal of INPUT 3.

When connecting a PC to the INPUT 3, set "Audio Select" to "Video+Audio". (See page 48.)

Q-16

Watching TV

Press POWER on the TV or on the remote control unit to turn the

power on.

POWER

DISPLAY_ _/s%°W_/

DVD,VCR AUDIO

POWER

(On/Standby)

o The Initial Installation starts when the TV powers on for the first time. Ifthe

TV has been turned on before, the Initial Installation will not be invoked. For

changing the settings of the Initial Installation, perform "EZ setup" on the Initial

Setup menu on page 30.

Press POWER on the TV or on the remote control unit again to turn the

power off.

o The TV enters standby and the image on the screen disappears.

o Ifyou are not going to use this TV for a long period of time, be sure to remove

the AC cord from the AC outlet.

• Weak electric power is still consumed even when the TV is turned off.

ENERGY STAR qualification is based on AV MODE

"STANDARD".

Air/Cable {Antenna setting)

Make sure what kind of connection is made with your TV

when selecting "Air" or "Cable".

3 Press _/_ to select "Air" or "Cable".

Press ENTER to enter the setting.

When you turn on the TV for the first time, it will

automatically memorize the broadcasting channels

available in the region where you live. Perform the

following steps before you press POWER on the

remote control unit.

1. Insert the batteries into the remote control unit. (See page 9.)

2. Connect the antenna cable to the TV. (See page 9.)

3. Plug in the AC cord to the AC outlet. (See page 8.)

AOUOS

NET DOCK

Language {Language setting)

Select from among 3 languages: English, French and Spanish.

1 Press A/V to select the desired language listed on the

screen, and then press ENTER.

OH Search {Channel search)

Channel auto search makes the TV look for all channels

viewable in the set area.

4 When "Air" is selected in Antenna setting:

Press 41/_ to select "Start", and then press ENTER.

TV Location

Select "Home" or "Store" for the location where you plan to

install the TV. This product qualifies for ENERGY STAR in

Home mode default setting.

2 Press _/_ to select "Home" or "Store".

Press ENTER to enter the setting.

When "Cable" is selected in Antenna setting:

Press A/Y to select "Analog & Digital Search Start" to

search both analog and digital broadcasts, or to select

"Analog Search Start" to search only analog broadcasts,

and then press ENTER.

Home: "Power Saving" is set to "Advanced", and AV

MODE is set to "STANDARD".

Store: "Power Saving" is set to "Off" and AV MODE is set to

"DYNAMIC (Fixed)", Picture Reset and Feature Demo can

be set,

Picture Reset: AV MODE will be set to "DYNAMIC (Fixed)"

regardless of whether Picture Reset is "On" or "Off", if you

select "On", AV MODE will be reset to "DYNAMIC (Fixed)" if

there is no operation for 30 minutes. When "Off" is selected,

AV MODE will be set to "DYNAMIC (Fixed)",

Feature Demo: When "On" is selected, after all the settings are

completed, the Fealure Demo screen is displayed ifthere is

no operation for several minutes,

= The Channel search will start automatically.

= To exit the Channel search screen, select "Cancel", and

then press ENTER.

o If no channel is found, confirm the type of connection

made with your TV and try "EZ Setup" again.

(See page 30.)

For changing the settings of the Initial Installation, perform

"EZ setup" on the Initial Setup menu on page 30.

Q-17

Direct Button Operation

_ _ gREC

EC3 EC3 EC] EC3

POWER

OPTION SLEEP SAVING RECSTOP

C3 [Z3

CO AVMODEVIEWMODEFLASHBACK

Ao0os

NET DOCK

FAVORITESURROUNDAUDIO FREEZE

You can change channels in several ways.

Method 1

Using CN/X/V on the remote control unit or on the TV.

Method 2

Using remote control buttons 0-9, • (DOT).

Examples:

Toselect a1or 2-digit channel number(e.g.,Channel5):

Press5_ ENT.

Toselect a3-digit channel number {e.g., Channel 115}:

Pressl_l_5_ENT.

Toselect a 4-digit channel number (e.g., Channel22.1):

Press2_ 2 _, (DOT} _ 1_ENT.

Method 3

Selecting the program from CH List.

1 Press INPUT on the remote control unit.

• The CH Listscreen displays,

2 Press _/_ to select "CABLE" or "AIR".

, A listof viewableprograms isdisplayed,

3 Press A/T to select the desired channel, and then

press ENTER.

Mutes the current sound output.

Press MUTE.

= "({_)" willbe displayed on the screenfor 30 minutes,and

the sound is silenced.

o Within 80 minutes of pressing MUTE, mute can be

canceled by pressing VOL+/- or MUTE,

Mute will be canceled after 80 minutes have passed.

However, the TV will not suddenly output a loud sound as

the volume level is set to 0 automatically.

Allows you to set a time when the TV automatically

switches to standby.

Press SLEEP.

= Theremainingtimedisplayswhenthesleeptimerhasbeenset.

= Each time you pressSLEEP, the remainingtime switches

asshown below.

Off ,m 30 ,_, 60 _ 90 _ 120

t I

= When set, the time automatically starts counting down.

= If you want to adjust the sleep timer, you can press SLEEP

twice then change the time setting.

= When it is 5 minutes before the time expires, the remaining

time will start to keep appearing every minute.

= Select "Off" by pressing SLEEP to cancel the sleep timer.

= TheTV willenter standby when the remainingtime reaches0

Press FLASHBACK to switch to the previously tuned

channel.

PressFLASHBACK againto switch backtothe currently

tuned channel.

FLASHBACK will not work if no channel has been

changed after the TV is turned on.

= When selecting a 1-digit channel number, it is not

necessary to press 0 before the number.

= When you enter 0-9 only, channel selection will be made if

there is no operation within a few seconds.

= Ifyou push "0" by itself, nothing will happen.

= Complete the above steps within a few seconds.

= When you enter 0-9 and • (DOT), channel selection will be

made if there is no operation within a few seconds.

You can change the volume by pressing VOL+/- on

the TV or on the remote control unit.

= To increasethe volume, pressVOL+.

= To decrease the volume, pressVOL-.

Audio status

The surround function produces Surround effect from

the speakers. Each time you press SURROUND, the

mode changes between On and Off.

On: Makesit possibleto enjoynatural,realisticsurround

sound.

Off: Outputs the normalsound.

= You can have the same settings by choosing "Surround"

on the menu items. (See page 26.)

Allows you to capture and freeze a moving image that

you are watching.

Press FREEZE.

A movingimageis captured,

• Press FREEZE againto cancelthe function,

Speaker Variable sound Mute

When "Output Select" is set to "Variable", the indicator on

the screen changes as shown below.

= See page 29 for details on the Output Select function.

= When this function is not available, "No displaying still

image available." will display.

= The still image automatically goes out after 30 minutes.

= If you are using the freeze function and a broadcast

activates the V-CHIP BLOCK, the freeze function will be

canceled and a V-CHIP BLOCK message will appear.

o You can have the same settings by choosing "Freeze" on

the menu items. (See page 28.)

(:D-18

Direct Button Operation

To view external source images, select the input source by

pressing INPUT on the remote control unit or on the TV.

1 Press iNPUT.

,, The OH List screen displays.

2 Press A/Y or press iNPUT again to select the input

source.

o An image from the selected source automatically displays.

o Each time iNPUT is pressed, the input source toggles.

= Ifthe corresponding inputisnot plugged in,you cannot change

the input.Besureto connectthe equipment beforehand.

= See pages 12 to 16 and 43 for external equipment

connection.

AV MODE gives you several viewing options to choose

from to best match the surrounding environment of the

TV, which can vary due to factors like room brightness,

type of program watched or the type of image input

from external equipment.

Press AV MODE. Current AV MODE displays.

= Press AV MODE again before the mode displayed on the

screen disappears. The mode changes as shown below:

Example:

When the input source is TM, iNPUT 1 or 2 terminals

AUTO _ STANDARD _ MOVIE _GAME

I !

DYNAMIC (Fixed)_ DYNAMIC _ USER [TV]

Example:

When the input source is INPUT 3, 4, 5, 6 or 7

terminals

AUTO _" STANDARD _ MOVIE _ GAME ,_ PC

l 1

DYNAMIC (Fixed)'= DYNAMIC ",=x.v.Color* = USER[ ie ]

* "x.v.Color" can only be selected when an x.v.Color

signal is input using INPUT 4 to 7.

AUTO: Optimizes the image quality automatically based

on the room brightness and image signal.

STANDARD: For a highly defined image in a normal

lighting.

MOVIE: For a movie.

GAME: Lowers image brightness for easier viewing.

PC: For PC.

USER: Allows the user to customize settings as desired.

You can set the mode for each input source.

x.v.Color: Supports the x.v.Oolor international standard

for wide color space. The x.v.Color signal allows you

to experience colors that conventional color signals

cannot reproduce.

DYNAMIC: For a clear-cut image emphasizing high

contrast, useful for sports viewing.

DYNAMIC (Fixed}: Changes the image and sound

settings to the factory preset values. No adjustments

are allowed.

II MTS/SAP stereo mode

The TV has a feature that allows reception of sound

other than the main audio for the program. This feature

is called Multi-channel Television Sound (MTS). The TV

with MTS can receive mono sound, stereo sound

and Secondary Audio Programs (SAP). The SAP

feature allows a TV station to broadcast other

information, which could be audio in another language

or something completely different like weather

information.

You can enjoy Hi-Fi stereo sound or SAP broadcasts

where available.

= Stereo broadcasts: View programs like live sporting

events, shows and concerts in dynamic stereo sound.

= SAP broadcasts: Receive TV broadcasts in either MAIN

or SAP sound.

MAIN sound: The normal program soundtrack (either in

mono or stereo).

SAP sound: Listen to a second language, supplementary

commentary or other information. (SAP is mono sound.)

If stereo sound is difficult to hear.

= Obtain a clearer sound by manually switching to fixed

mono-sound mode.

You can change MTS as shown below to match the television

broadcast signal.

Press AUDIO to toggle between audio modes.

Examples: when receiving MTS and SAP

STEREO mode: STEREO_,_ MONO

STEREO + SAP mode: ST(SAP),=, SAP(ST),=, MONO

"It I

MAIN + SAP mode: MAIN*,_ SAP

MONO mode: MONO

II Digital broadcasting audio mode

The types of audio transmitted in a digital broadcast include

SURROUND as well as MONO and STEREO. Inaddition, it

is possible for multiple audio tracks to accompany a single

video track.

Press AUDIO to toggle between audio modes.

Example: when receiving Digital broadcasting

STEREO (Audio1) ._ STEREO (Audio2)

t.... SURROUND (Audio3) 4_..-1

= MTS only operates while in TV mode.

= You can have the same settings by choosing "Change

Audio" on the menu items. (See page 28.)

= You can select a different AV MODE item for each input

mode. (For example, select STANDARD for TV input and

DYNAMIC for INPUT 1.)

= When you play games, "GAME" is recommended for AV

MODE.

o You cannot set "GAME" or "PC" when the TV is connected

to the Internet or when the input source is "USB".

o You can have the same settings by choosing "AV MODE"

on the menu items. (See page 24.)

Q-19

Page is loading ...

Sharp AQUOS LC-46LE820UN Operating instructions

Brand: Sharp

Model: AQUOS LC-46LE820UN

Category: LCD TVs

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Sharp AQUOS LC-46LE820UN Operating instructions

This manual is also suitable for

Sharp AQUOS LC-46LE820UN Operating instructions

Related papers

Other documents