McIntosh RS100 Operating instructions

Brand: McIntosh

Model: RS100

Category: Supplementary music equipment

Type: Operating instructions

McIntosh RS100: The Art of Sound Redefined - Experience the pinnacle of wireless audio with our state-of-the-art loudspeaker system. Stream your favorite music from any Bluetooth-enabled device or seamlessly integrate it into your home network for a multi-room audio experience.

McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.com

RS100

Wireless Loudspeaker

System

Operation Guide

Ne pas exposer cet appareil à des éclaboussures ou

gouttelettes d’un liquide. Aucun objet remplie de

liquide comme par exemple un vase ne doit être placé

sur l’appareil.

16. If this equipment is supplied with a power supply cord

only, the mains plug of the power supply cord shall

remain readily operable. To completely disconnect this

equipment from the a.c. mains remove the plug from

the a.c. receptacle.

Si l’équipement est uniquement alimenté par un cordon

G¶DOLPHQWDWLRQOD¿FKHGXFRUGRQG¶DOLPHQWDWLRQGRLW

demeurer aisément accessible. Pour déconnecter

complètement l’équipement du réseau d’alimentation,

GpFRQQHFWHUOD¿FKHGXFRUGRQG¶DOLPHQWDWLRQGHOD

prise murale.

17. If this equipment is supplied with AC /DC Adapter

with separate power supply cord or the AC/DC Adapter

plugging directly into an a.c. receptacle, they shall

remain readily operable. To completely disconnect this

equipment from the a.c. mains remove the AC /DC

Adapter mains power supply cord from the a.c. recep-

tacle or remove the AC /DC Adapter when it is directly

plugged into the a.c. receptacle.

Si l’équipement est alimenté par un adaptateur AC/DC

munis d’un cordon d’alimentation ou un adaptateur

AC/DC qui est alimenté directement à la prise mu-

rale, ils doivent demeurer aisément accessibles. Pour

déconnecter complètement l’équipement du réseau

d’alimentation, déconnecter l’adaptateur AC/DC de la

prise murale ou déconnecter le cordon d’alimentation

de l’adaptateur AC/DC de la prise murale.

18. WARNING: Do not expose batteries or battery pack to

H[FHVVLYHKHDWVXFKDVVXQVKLQH¿UHRUWKHOLNH

AVERTISSEMENT: Les batteries ou bloc de batteries

ne doivent pas etre exposees a une chaleur excessive

telle que celle du soleil, feu ou autre source de chaleur

similaire.

19. CAUTION: danger of explosion if battery is incorrect-

ly replaced. Replace only with the same or equivalent

type.

ATTENTION: danger d’explosion si la pile n’est pas

remplacée correctement. Ne remplacer que par le

même type ou un type équivalent.

20. Connect mains power supply cord only to a mains

socket outlet with a protective earthing connection.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accor-

dance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

DPSOL¿HUVWKDWSURGXFHKHDW

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

WKHSURYLGHGSOXJGRHVQRW¿WLQWR\RXURXWOHWFRQVXOW

an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

2QO\XVHDWWDFKPHQWVDFFHVVRULHVVSHFL¿HGE\WKH

manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table

VSHFL¿HGE\WKHPDQXIDFWXUHURUVROGZLWKWKHDSSDUD-

tus. When a cart is used, use caution when moving the

cart/apparatus combination to avoid injury

from tip-over.

13. Unplug this apparatus during lightning

storms or when unused for long periods of

time.

5HIHUDOOVHUYLFLQJWRTXDOL¿HGVHUYLFHSHUVRQQHO

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

15. Do not expose this equipment to dripping or splashing

DQGHQVXUHWKDWQRREMHFWV¿OOHGZLWKOLTXLGVVXFKDV

vases, are placed on the equipment.

7KHOLJKWQLQJÀDVKZLWKDUURZKHDGZLWKLQDQHTXLODWHUDOWULDQJOHLV

intended to alert the user to the presence of uninsulated “dangerous

YROWDJH´ZLWKLQWKHSURGXFW¶VHQFORVXUHWKDWPD\EHRIVXI¿FLHQWPDJQL-

tude to constitute a risk of electric shock to persons.

7KHH[FODPDWLRQSRLQWZLWKLQDQHTXLODWHUDOWULDQJOHLVLQWHQGHGWRDOHUW

the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

ATTENTION:

RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

WARNING - TO REDUCE RISK OF FIRE OR

ELECTRICAL SHOCK, DO NOT EXPOSE THIS

EQUIPMENT TO RAIN OR MOISTURE.

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED PERSONNEL.

To prevent the risk of electric shock, do not

remove cover or back. No user-serviceable

parts inside.

IMPORTANT SAFETY

INSTRUCTIONS!

PLEASE READ THEM BEFORE

OPERATING THIS EQUIPMENT.

Your decision to own this McIntosh RS100 Wireless

Loudspeaker System ranks you at the very top among

discriminating music listeners. You now have “The

Best.” The McIntosh dedication to “Quality,” is as-

surance that you will receive many years of musical

enjoyment from this unit.

Please take a short time to read this information. We

want you to be as familiar as possible with all the fea-

tures and functions of your new McIntosh.

Thank You

Please Take A Moment

Technical Assistance

If at any time you have questions about your McIntosh

product, contact your McIntosh Dealer who is familiar

with your McIntosh equipment and any other brands

that may be part of your system. If you or your Dealer

wish additional help concerning a suspected problem,

you can receive technical assistance for all McIntosh

products at:

McIntosh Laboratory, Inc.

2 Chambers Street

Binghamton, New York 13903

Phone: 607-723-3512

Fax: 607-724-0549

The serial number, purchase date and McIntosh Dealer

name are important to you for possible insurance claim

or future service. The spaces below have been provided

for you to record that information:

Serial Number: _____________________________________

Purchase Date: _____________________________________

Dealer Name: ______________________________________

Customer Service

If it is determined that your McIntosh product is in need

of repair, you can return it to your Dealer. You can also

return it to the McIntosh Laboratory Service Depart-

ment. For assistance on factory repair return procedure,

contact the McIntosh Service Department at:

McIntosh Laboratory, Inc.

2 Chambers Street

Binghamton, New York 13903

Phone: 607-723-3515

Fax: 607-723-1917

Table of Contents

Safety Instructions ......................................................... 2

Thank You and Please Take a Moment ......................... 2

Technical Assistance and Customer Service ................. 2

Table of Contents ........................................................... 2

General Information ...................................................... 2

RS100 Quick Start .................................................... 3 - 9

Introduction ..................................................................10

FCC INFORMATION(For US and Canada Customers)

is Product Contains FCC ID:2AAWQ-CAPRI-

CA2L

a) User Information acc. to FCC15.21 as following:

Changes or modications not expressly approved by

the party responsible for compliance could void the

user’s authority to operate the equipment.

b) Statement for Class B digital device acc. to FCC

15.105 as following:

NOTE: is equipment has been tested and found

to comply with the limits for a Class A/B

digital device, pursuant to part 15 of the

FCC Rules. ese limits are designed to

provide reasonable protection against harm-

ful interference in a residential installation.

is equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interfer-

ence to radio communications. However,

there is no guarantee that interference will

not occur in a particular installation. If this

equipment does cause harmful interference

to radio or television reception, which can

be determined by turning the equipment

o and on, the user is encouraged to try to

correct the interference by one or more of

the following measures:

—Reorient or relocate the receiving

antenna.

—Increase the separation between the

equipment and receiver.

—Connect the equipment into an outlet

on a circuit dierent from that to which

the receiver is connected.

—Consult the dealer or an experienced

radio/ TV technician for help.

—is device complies with Industry

Canada licence-exempt RSS stan-

dard(s). Operation is subject to the fol-

lowing two conditions: (1) this device

may not cause interference, and (2) this

device must accept any interference,

including interference that may cause

undesired operation of the device.

Le présent appareil est conforme aux

CNR d’Industrie Canada applicables

aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux

conditions suivantes : (1) l’appareil ne

doit pas produire de brouillage, et (2)

l’utilisateur de l’appareil doit accepter

tout brouillage radioélectrique subi,

même si le brouillage est susceptible

d’en compromettre le fonctionnement.

c) e device must be kept more than 20 cm from all

persons.

General Information

1. For additional connection information, refer to the

RZQHU¶VPDQXDOVIRUDQ\FRPSRQHQWVFRQQHFWHG

to the RS100 Wireless Loudspeaker System.

2. For the RS100 to receive streaming audio signals

from a mobile device, a wireless router with Wi-Fi

capabilities is required, in order to facilitate commu-

nications between the RS100 and the mobile device.

3. When connecting the RS100 to a wired Home

Computer Network (of which

LQFOXGHVDZLUHOHVVURXWHUD

86%WR(WKHUQHW5-

Adapter such as a Monoprice

LVUHTXLUHG

4. The RS100 is designed to be

compatible with the majority of Powered Subwoof-

ers. However, do to a wide range of Powered Sub-

woofer Designs, it is important the input sensitivity

of the Subwoofer be at least 0.2 Volts. This will as-

sure music recordings are reproduced with adequate

dynamic range. Check with your McIntosh Dealer

for additional information.

5. The performance of the RS100 is dependent upon the

speed and operational range of the Wireless Router

used.

6. When the RS100 is connected to a wired Home

Computer Network with a Wireless Router, the

speed should be 1 Gigabit or faster.

7. The Play-Fi App for Streaming Music and Remote

Control Operation of the RS100 is available at Web

Sites for download free of charge:

For Apple Powered Mobile Devices:

KWWSVLWXQHVDSSOHFRPXVDSSSOD\¿LG"

mt=8

For Android Powered Mobile Devices:

KWWSVSOD\JRRJOHFRPVWRUHDSSVGHWDLOV"LG FRP

 SKRUXVSOD\¿KO

8. When discarding the unit, comply with local

rules or regulations.

9. Periodically, check the McIntosh Web Site at

www.mcintoshlabs.com for the latest infor-

mation on the RS100 and other McIntosh Products.

Performance Features ...................................................10

Rear Panel Connections ................................................10

Connecting to External Components ...........................10

How to Operate the RS100 ...........................................11

Specifications............................................................... 12

Packing Instructions .................................................... 12

STEP 1

RS100 Quick Start, for Apple Powered Devices

STEP 2

STEP 3

ACCESSORY

PACK

REMOVE UNIT FROM CARTON

CONNECT THE SUPPLIED AC CORD

REMOVE PROTECTIVE COVER

AND OPEN ACCESSORY PACK

COVER

STEP 4

RS100

REMOVE

AC CORD

AC OUTLET

AC CORD CONNECT TO THE

RS100 CONNECTOR

THE RS100 IS COMPATIBLE WITH BOTH APPLE POWERED

AND ANDROID POWERED MOBILE DEVICES. THERE ARE

OPERATIONAL DIFFERENCES BETWEEN BOTH TYPES OF

MOBILE DEVICES

WHEN USING AN APPLE POWERED MOBILE DEVICE, PRO-

CEED TO STEP 5 ON PAGE 3 “RS100 QUICK START”SEC-

TION OF THIS OPERATION GUIDE

WHEN USING AN ANDROID POWERED MOBILE DEVICE,

PROCEED TO STEP 9 ON PAGE 7 “RS100 QUICK START”

SECTION OF THIS OPERATION GUIDE

STEP 5

DOWNLOAD AND INSTALL THE PLAY-FI APP TO

YOUR APPLE POWERED MOBILE DEVICE

The Play-Fi App for Music

Streaming and Remote Operation

of the RS100 is available at the

Web Site for download free of

charge:

For Apple Powered Mobile Devices:

https://itunes.apple.com/us/app/play-fi/

id779245456?mt=8

MOBILE DEVICE

PLAY-FI APP

NOTE:

The graphic illustration of this Apple Powered Mobile Device

may vary slightly from your Apple Mobile Device.

REMOVE PROTECTIVE

PLASTIC FILM FROM

THE FRONT PANEL

STEP 7 ESTABLISH COMMUNICATIONS WITH THE MOBILE DEVICE, SETTING UP THE PLAY-FI APP

FOR A SINGLE RS100 AND EACH RS100 OF A STEREO PAIR

3rd - SELECT

“Play-Fi APP”

5th - SELECT

“Settings”

6th - SELECT

“Wi-Fi”

7th - LOCATE Play-Fi

Device (RS100)

9th - Communications

established with

RS100

10th - SELECT

“Play-Fi

APP”

STEP 6 ESTABLISH CONNECTION WITH

A WIRELESS ROUTER

SELECT

SETTINGS

SELECT Wi-Fi

SETTINGS

SELECT YOUR

ROUTER

NOTE: If your Apple Powered Mobile Device is currently Wi-Fi Connected to your

Wireless Router, proceed to STEP 7.

USB

Ethernet

Adapter1

Wired Network

Router

Wireless

Network

Router

Wireless

Network

Router

WIRED NETWORK WITH

WIRELESS Wi-Fi ROUTER

WIRELESS NETWORK

Wi-Fi ROUTER

NOTES:

1 Refer to the page 2, note 3 for additional information.

2 7KHWHUP³<RXU1HWZRUN´LVXVHGWRUHIHUWRQDPHRIWKHZLUHG1HWZRUNZLWK:LUHOHVV5RXWHU

connected to the RS100 or just a Network Wireless Router used with the RS100.

3 It is advisable, during the initial communications setup, to physically locate the RS100 and the Wire-

less Router in close proximity to one another.

4,IWKHUHLVGLI¿FXOW\LQHVWDEOLVKLQJFRPPXQLFDWLRQVEHWZHHQWKHQHWZRUN5RXWHU56DQGRUWKH

Mobile Device, temporarily switch Off other Wi-Fi devices connected to the same Router.

5 The performance capability of the network wireless router can effect whether the RS100 connects

to your mobile device and the quality of the music streamed. For additional information on wireless

routers refer to KWWSVSOD\¿FRPIDTHQWU\UHFRPPHQGHGURXWHUVDQGQHWZRUNVSHFL¿FDWLRQV

1st - PRESS IN AND RELEASE

TO POWER ON A SINGLE

RS100

2nd - GREEN LED INDICATES

WHEN THE RS100 IS IN

THE SETUP MODE, FOR

ESTABLISHING WIRELESS

OR WIRED NETWORK

CONNECTIONS

Continue to

STEP 7, Num-

ber 11 on the

8th - Setting Up

communications

with RS100

4th - SELECT “Set-up New Device”

NOTE: Proceed with “Set-up new De-

vice” after the “WI-FI/NET” LED

LQGLFDWRUFKDQJHVIURPÀDVKLQJ

rapidly to slowly pulsing On/Off.

11th - SELECT

“Your

Network”

12th - Enter your

Network

Password

if required

13th - SELECT

“Set-up”

Play-Fi

Connecting

to Your Router

14th - SELECT the

name of the

room where

the RS100 is

located

16th - SELECT

“Music” to

start playback

of the desired

music

RS100 Quick Start for Apple Powered Devices, con’t

STEP 7, con’t

15th - SELECT “Location Name”

NOTE: The “WI-FI/NET” LED

indicator will change

from slowly pulsing On/

Off to On all the time.

STEP 8 ESTABLISH COMMUNICATIONS WITH THE MOBILE DEVICE, SETTING UP THE

PLAY-FI APP FOR A STEREO PAIR

17th - SELECT

“Play-Fi

APP”

While a single RS100 may be

used in a room for a Monaural

Sound Stage, most RS100s will be

used in pairs to produce a Stereo

Sound Stage.

When RS100s are going to be

used as a Stereo Pair in a room,

some additional setup procedures

are required.

After Step 7 (number 3 thru 16)

has been completed and music

is streaming from your mobile

device to the single RS100, then

perform the following additional

steps:

1. Stop the stream of music and

return to the Mobile Device

Main Icon Screen.

2. Then switch Power Off to the

working RS100.

3. Switch Power On to the sec-

ond RS100 and perform Step

6 (number 3 thru 16) for this

RS100.

4. After music is playing from

the second RS100, stop mu-

sic playback and return to

the Mobile Device Main Icon

Screen, refer to number 16.

5. Switch power back On to the

¿UVW56VZLWFKHG2IILQ

step 1).

6. Perform Step 8 (number 17

thru 28) to setup the pair of

RS100s as Left and Right

Channels.

18th - Display of

the RS100

pair loca-

ted in the

same room

19th - Select the

“Play-Fi

Settings

Menu”

20th - Select

“Stereo

Pair”

21st - Select

“Create

a Stereo

Pair”

22nd - Press the Icons (one at a

time) to identify which

Loudspeaker is playing the

Left Channel Sound

23rd - Select the

“Left Channel

Loudspeaker”

Continue

to STEP 8,

Number 24

on the next

page

RS100 Quick Start for Apple Powered Devices, con’t

STEP 8, con’t

24th - Select the

“Right Channel

Loudspeaker”

25th - Enter a Name

for the just created

Stereo Pair of

Loudspeakers

26th - Select “DONE”

for the just created

Stereo Pair of

Loudspeakers

27th - Select

“MASTER

BEDROOM 12”

28th - Select “MUSIC” to

start playback

of desired music

ESTABLISH COMMUNICATIONS WITH THE MOBILE DEVICE,

SETTING UP THE PLAY-FI APP FOR A STEREO PAIR, con’t

RS100 Quick Start for Android Powered Devices, con’t

STEP 9

DOWNLOAD AND INSTALL THE PLAY-FI APP TO

YOUR ANDROID POWERED MOBILE DEVICE

The Play-Fi App for Music

Streaming and Remote

Operation of the RS100 is

available at the Web Site for

download free of charge:

For Android Powered Mobile Devices:

 KWWSVSOD\JRRJOHFRPVWRUHDSSVGHWDLOV"

LG FRPSKRUXVSOD\ILKO

MOBILE DEVICE

PLAY-FI APP

NOTE:

The graphic illustration of this Android Powered Mobile Device

may vary slightly from your Android Mobile Device.

STEP 10 ESTABLISH CONNECTION WITH A WIRELESS ROUTER

SELECT SETTINGS SELECT Wi-Fi SETTINGS SELECT YOUR ROUTER

NOTE: If your Android Powered Mobile Device is currently Wi-Fi Connected to your Wireless Router, proceed to STEP 11.

USB to Ethernet Adapter1

Wired Network

Router

Wireless Network

Router

WIRED NETWORK WITH WIRELESS Wi-Fi ROUTER WIRELESS NETWORK Wi-Fi ROUTER

Wireless Network

Router

NOTES:

1 Refer to the page 2, note 3 for additional information.

2 7KHWHUP³<RXU1HWZRUN´LVXVHGWRUHIHUWRQDPHRIWKHZLUHG1HWZRUNZLWK:LUHOHVV5RXWHUFRQQHFWHGWRWKH56RUMXVWD1HWZRUN:LUHOHVV5RXWHUXVHGZLWKWKH56

3 It is advisable, during the initial communications setup, to physically locate the RS100 and the Wireless Router in close proximity to one another.

4,IWKHUHLVGLI¿FXOW\LQHVWDEOLVKLQJFRPPXQLFDWLRQVEHWZHHQWKHQHWZRUN5RXWHU56DQGRUWKH0RELOH'HYLFHWHPSRUDULO\VZLWFK2IIRWKHU:L)LGHYLFHVFRQQHFWHGWRWKHVDPH5RXWHU

5 The performance capability of the network wireless router can effect whether the RS100 connects to your mobile device and the quality of the music streamed. For additional information on wireless routers refer

to KWWSVSOD\¿FRPIDTHQWU\UHFRPPHQGHGURXWHUVDQGQHWZRUNVSHFL¿FDWLRQV

STEP 11 ESTABLISH COMMUNICATIONS WITH THE RS100

3rd - SELECT

“Play-Fi APP”

5th - ENTER

“Network

(Router)

Password”

6th - SELECT

“Next”

Searching for Play-Fi Devices

7th - SELECT the name of

the room where the

RS100 is located

8th - SELECT “Location Name”

NOTE: The “WI-FI/NET” LED

indicator will change

from slowly pulsing On/

Off to On all the time.

9th - SELECT “Music”

to start playback of

desired music

4th - SELECT “Set-up New Device”

NOTE: Proceed with “Set-up new Device” after the

“WI-FI/NET” LED indicator changes from

ÀDVKLQJUDSLGO\WRVORZO\SXOVLQJ2Q2II

1st - PRESS IN AND RELEASE

TO POWER ON A SINGLE

RS100

2nd - GREEN LED INDICATES

WHEN THE RS100 IS IN

THE SETUP MODE, FOR

ESTABLISHING WIRELESS

OR WIRED NETWORK

CONNECTIONS

STEP 12 ESTABLISH COMMUNICATIONS WITH THE MOBILE DEVICE, SETTING UP THE PLAY-FI APP FOR A STEREO PAIR

10th - SELECT “Play-Fi

APP”

While a single RS100 may be

used in a room for a Monaural

Sound Stage, most RS100s will be

used in pairs to produce a Stereo

Sound Stage.

When RS100s are going to be

used as a Stereo Pair in a room,

some additional setup procedures

are required.

After Step 11 (number 3 thru 9)

has been completed and music

is streaming from your mobile

device to the single RS100, then

perform the following additional

steps:

1. Stop the stream of music and

return to the Mobile Device

Main Icon Screen.

2. Then switch Power Off to the

working RS100.

3. Switch Power On to the sec-

ond RS100 and perform Step

11 (number 3 thru 9) for this

RS100.

4. After music is playing from

the second RS100, stop mu-

sic playback and return to

the Mobile Device Main Icon

Screen, refer to number 9.

5. Switch power back On to the

¿UVW56VZLWFKHG2IILQ

step 1).

6. Perform Step 12 (number 10

thru 18) to setup the pair of

RS100s as Left and Right

Channels.

11th - Display of the

RS100 pair located

in the same room

12th - Select the “Play-

Fi Settings Menu”

13th - Select “Stereo Pair” 14th - Press the Icons (one at a time)

to identify which Loudspeaker is

playing the Left Channel Sound

15th - Select the “Left Channel

Loudspeaker”

RS100 Quick Start for Android Powered Devices, con’t

16th - Enter a Name for the just

created Stereo Pair of

Loudspeakers

17th - Select “MASTER

BEDROOM 2”

18th - Select “MUSIC” to

start playback of

the desired music

Dimensions

The following dimensions can assist in determin-

ing the best location for your RS100. There is ad-

ditional information below pertaining to installing

the RS100 into cabinets.

Front View of the RS100

Wireless Loudspeaker System

Rear View of the RS100

Wireless Loudspeaker System

Side View of the RS100

Wireless Loudspeaker System

8.2"

20.8cm

13"

33.1cm

7.6"

19.4cm

20.3cm

15.2cm

5.7"

14.4cm

4.1"

10.4cm

Low Frequency

Acoustic Opening

Note: For proper

Low Frequency

Performance do not

block the Acoustic

Opening.

RS100

Front View

5.1cm

RS100

Side View

7.6cm

Low Frequency

Acoustic Opening

Note: For proper

Low Frequency

Performance do not

block the Acoustic

Opening.

The RS100 is designed to be placed upright on a

table or shelf. For proper Low Frequency perfor-

mance do not block the Acoustic Opening located

on the RS100 Rear Panel. Do not install the RS100

directly above a heat generating device. Allow at

Installation

OHDVWLQFKHVFPDERYHWKHWRSLQFKFP

RQERWKVLGHVDQGDWOHDVWLQFKHVFPEHKLQG

the Rear Panel so that airflow is not obstructed and

proper Low Frequency performance is achieved.

Now you can take advantage of traditional McIn-

tosh standards of excellence in the RS100 Wireless

Loudspeaker System.

The RS100 provides superior spaciousness

sound reproduction with unusual sound stage

depth. The McIntosh Sound is “The Sound of the

Music Itself.”

Introduction

Performance Features

• Play-Fi®

Listen to music from wireless mobile devices.

• Streaming Radio

The RS100 allows for listening to Internet Radio

Stations and local AM/FM Stations (via the Inter-

QHWZKHQFRQQHFWHGWRDPRELOHGHYLFHXVLQJWKH

Play-Fi App.

• Auxiliary Input

The RS100 Aux Input accommodates a wide range

of analog audio components. The Amplifier uses

noiseless and reliable Electronic Input Switching

and is designed to drive the built-in McIntosh

Loudspeakers to a high level of performance.

• Built-in Networking Capability

The RS100 has the ability to connect to an existing

network for connecting to other devices such as

NAS Storage Devices.

• Subwoofer Output

The RS100 Sub Output accommodates a wide

range of available Powered Subwoofer Loudspeak-

ers.

• Integrated Loudspeaker Design

The RS100 Integrated Loudspeaker Design incor-

porates a Woofer and Midrange/Tweeter, a DSP

Electronic Crossover with active Equalization,

dual Power Amplifiers and achieves a high level of

sonic performance.

• Illuminated Output Level Meter

The Illuminated Peak Responding Output Level

Meter on the RS100 is calibrated in Decibels and

responds to 95% of a full scale reading to a single

cycle tone burst signal.

• Solid State Front Panel Illumination

The illuminated Front Panel is accomplished by

H[WUDORQJOLIH/LJKW(PLWWLQJ'LRGHV/('V

Introduction, Performance Features, Dimensions, Installation, Rear Panel Connections and Connecting to External Components

Rear Panel Connections

AUX INput accepts

high level signals

from a source

SUB OUT supplies an ana-

log audio signal to the input

on a Powered Subwoofer

USB Connector for

connection to a wired

network via an adapter1

and for service use

1for additional information refer to page 2

“General Information”, number 3

Connect the supplied

AC Power Cord to a

live AC outlet

Connecting to External Components

The RS100 connection instructions below, together

with the Connection Diagram below (single chan-

QHOLVDQH[DPSOHRIFRQQHFWLQJRSWLRQDOH[WHUQDO

components. Your external components may vary

from this, however the actual components would

be connected in a similar manner.

Analog Audio Connections:

&RQQHFWDFDEOHVIURPWKH56$8;,1SXW

to the external SACD/CD Transport unbal-

anced audio output jack.

1RWH)RU6WHUHR2SHUDWLRQEHWZHHQWKH

56V/HIWDQG5LJKW&KDQQHOVDQG

WKH6$&'&'7UDQVSRUWWZRMDFNVDUH

UHTXLUHG

&RQQHFWDFDEOHVIURPWKH5668%ZRRIHU

OUT to the external Powered Subwoofer input

MDFNV/HIWDQG5LJKW&KDQQHOV

1RWH,IWKH3RZHUHG6XEZRRIHUKDVRQO\RQH

LQSXWMDFNXVHD³<´$GDSWHUWRFRQQHFW

WKHRXWSXWVIURPERWK56¶VWRWKH

VLQJOHLQSXWMDFN

3. Connect the supplied AC Power Cord between

the AC Socket on the Rear Panel of the RS100

WRDOLYH$&RXWOHWWKDWLVDOZD\V2Q

SACD/CD Transport

USB

Ethernet

Adapter1

Wired Network Router

Wireless

Network

Router

Powered Subwoofer

SDUWLDOYLHZ

Connect to

AC Outlet

;Q7<B=A6:/0=@/B=@G7<1

07<56/;B=<<G

;12##

A/1212 >:/G3@

6/<21@/4B327<CA/E7B6CA/<27;>=@B32>/@BA

Wireless

Network

Router

STANDBY/ON Control

switches the RS100 ON or

OFF by pressing in the Con-

trol; rotate the Input Control

to select the AUX Input for

listening

Rotate the Volume Control to increase or

decrease the listening level, press momentari-

ly in the Volume Control to Mute or Un-Mute

the sound. The word “VOLUME” above the

Volume Control will flash when minimum

or maximum listening level has been reached

and also flashes when Muting is active

Rapid flashing of the

Green LED Indicates

the initial start of the

Network Communi-

cation process. Slow

pulsing of the Green

LED indicates the Net-

work Communication

process is proceeding.

Steady illumination of

the Green LED Indica-

tor indicates Network

Communication has

been established

Indicates when the

RS100 is in Standby.

It also indicates the

operational status

E\FRORURIWKH

currently selected

Input. Refer to the

chart below

Front Panel Controls, Display and How to Operate the RS100

Your McIntosh RS100 is factory configured for im-

mediate enjoyment of superb audio from a Mobile

Device via Play-Fi or an external Audio Compo-

nent Source connected to the AUX Input.

If you wish to make a Play-Fi Wireless Connec-

tion between the Mobile Device and the RS100,

please refer to “RS100 Quick Start” starting on

SDJHVWHSIRUDGGLWLRQDOLQIRUPDWLRQ

Power On/Off

Momentarily press the STANDBY/ON - INPUT

Control on the RS100 Front Panel to switch it On.

To switch Off the RS100 Press and release the

STANDBY/ON - INPUT Control on the Front

Panel.

1RWHV7KH6OHHS0RGHLQGLFDWHGE\WKH/('\HO-

ORZDOORZVIRUUHVXPSWLRQRIOLVWHQLQJDIWHU

VZLWFKLQJWKH56EDFN2Q

7KH6WDQGE\0RGHLVDFWLYDWHGE\SUHVVLQJ

IRUILYHVHFRQGVDQGWKHQUHOHDVLQJWKH

67$1'%<21,1387&RQWURO:KHQ

VZLWFKLQJWKH56EDFN2QIURPWKH

6WDQGE\0RGHWKHZLUHOHVVFRQQHFWLRQZLOO

QHHGWREHUHHVWDEOLVKHG

Power Mode

The RS100 incorporates an Auto Off Feature,

which automatically places it into the Power Saving

Mode. This occurs approximately 30 minutes after

there has been an absence of audible audio signals

on the selected input. To change the current setting

perform the following:

Press and hold in simultaneously the STAND-

BY/ON - INPUT Control and the VOLUME

Control until the LED located below STAND-

BY/ON - INPUT Control flashes twice.

1RWH7KHFRORURIWKH/('ZKHQLWIODVKHVLQGL-

FDWHVZKLFKPRGHWKH3RZHU6DYLQJ0RGH

LVQRZVHWWR7KHFRORU*5((1LQGLFDWHV

2QDQGWKHFRORU5('LQGLFDWHV2II

Source Selection

Select Play-Fi Input by pressing the Play-Fi Screen

Icon located on the Mobile Device used to estab-

lish Network Connection with the RS100. Refer to

³564XLFN6WDUW´VWDUWLQJRQSDJHVWHSIRU

additional information.

Select the AUX Input Source by rotating the

STANDBY/ON - INPUT Control. The LED below

the Control will change from green to blue in color

to indicate the AUX Input Source has been select-

ed.

How to Operate the RS100

Meter indicates the Output

of the Amplifier and other

operational changes

Standby/Input Indicator

Color Operation

Red Connected to AC Power and in Standby Mode

Yellow Sleep Mode

Green 3OD\)L,QSXW1HWZRUN&RQQHFWLRQ

Blue $X[,QSXW5HDU3DQHO&RQQHFWLRQ

1RWH7KH0RELOH'HYLFHZLOOSDXVHWKHFXUUHQW

WUDFNSOD\LQJZKHQVZLWFKLQJWR$8;,QSXW

Source on the RS100.

Volu me L evel

To increase the Volume Level, rotate the Front

Panel VOLUME Control clockwise. To lower the

Volume Level, rotate the Front Panel VOLUME

Control counterclockwise. When the maximum or

minimum volume level is reached the word “VOL-

UME” will flash rapidly.

1RWHV:KHQWKH56LVLQ3OD\)L0RGHDQG

WKH)URQW3DQHO9ROXPH&RQWURO6HWWLQJ

LVFKDQJHGWKH0RELOH'HYLFH9ROXPH

$GMXVWPHQW,QGLFDWRUZLOODOVRLQGLFDWHWKH

change.

:KHQXVLQJDSDLURI56VLQWKH6WHUHR

0RGHRI2SHUDWLRQWKH)URQW3DQHO92/-

80(&RQWUROVRQWKH56PD\EHXVHG

WRDOWHUWKHFKDQQHOEDODQFHEHWZHHQWKH

/HIWDQG5LJKW&KDQQHOV:KHQWKH56V

DUHVZLWFKHG2IIDQGEDFN2QWKHSUHYL-

RXV&KDQQHO%DODQFHDGMXVWPHQWPDGHLV

UHWXUQHGWRWKHQRUPDOVHWWLQJ

Mute

To mute the volume level, momentarily press in

on the Front Panel VOLUME Control. During

the time the sound is muted the Front Panel word

“VOLUME” will f lash slowly. To un-mute and

return to the previous volume level, momentarily

press in on the Front Panel VOLUME Control.

When the Play-Fi Input is selected on the RS100,

the Mobile Device can also Mute and Un-Mute the

sound.

1RWH:KHQWKH56LVLQ3OD\)L0RGHDQG

WKH0XWH)XQFWLRQLVHQJDJHGXVLQJWKH

)URQW3DQHO92/80(&RQWUROWKH0RELOH

'HYLFH0XWHLQGLFDWLRQZLOODOVRLQGLFDWH

the change.

Meter Illumination

If desired, the illumination of the OUTPUT LEV-

EL Meter may be switched Off by performing the

following steps:

1. Momentarily press the STANDBY/ON - IN-

PUT Control and VOLUME Control at the

same time and the Meter Illumination will

switch Off.

2. To switch On the Meter Illumination repeat

step 1.

Play-Fi

For Mobile Device specific information (Apple or

$QGURLGJRWRWKH3OD\)LZHEVLWHDWhttps://play-

ILFRP

1RWHV,I\RXKDYHTXHVWLRQVDERXWWKH3OD\)L

$SSDQGLWV2SHUDWLRQUHIHUWRWKH3OD\)L

³.QRZOHGJH%DVH´IRUDGGLWLRQDOLQIRUPD-

tion.

6RPHRIWKH,QWHUQHW0XVLF6WUHDPLQJ6HU-

YLFHVDYDLODEOHYLDWKH3OD\)L$SSRIIHU

WKHOLVWHQHUWKHDELOLW\WRDOWHUWKHVRXQG

TXDOLW\RIPXVLFEHLQJVWUHDPHG5HIHUWR

HDFKRIWKH0XVLF6WUHDPLQJ6HUYLFH¶V,Q-

WHUQHW:HE6LWHIRUDGGLWRQDOLQIRUPDWLRQ

RQKRZWRPDNHFKDQJHVWRWKHLUGHIDXOW

VHWWLQJVLIDYDLODEOH

Reset of Microprocessors

In the unlikely event the controls of the RS100 stop

functioning, the internal microprocessors can be

reset by performing the following:

1. Disconnect the AC Power Cord from the Rear

Panel of the RS100, wait two minutes and then

reconnect AC Power Cord to the Rear Panel of

the RS100.

2. Momentarily press the STANDBY/ON - IN-

PUT Control switching back On the RS100 and

then resume listening.

Resetting to Factory Default Settings

If it becomes desirable to reset all of the RS100

settings to the factory default values, perform the

following steps:

Warning$IWHUWKH56LVUHWXUQHGWR)DFWRU\

'HIDXOW6HWWLQJVLWZLOOEHFRPHQHFHVVDU\

WRUHHVWDEOLVKFRPPXQLFDWLRQVEHWZHHQ

WKH56DQGWKH0RELOH'HYLFHYLDWKH

1HWZRUN&RPPXQLFDWLRQV5HIHUWR³56

4XLFN6WDUW´VWDUWLQJRQSDJHVWHSIRU

DGGLWLRQDOLQIRUPDWLRQ

1. With the RS100 On, press and hold in simulta-

neously the STANDBY/ON - INPUT Control

and VOLUME Control until the meter starts to

deflect upwards followed by an audible beep,

then release both controls.

2. Disconnect the AC Power Cord from the Rear

Panel of the RS100, wait two minutes and then

reconnect the AC Power Cord to the Rear Panel

of the RS100.

3. Proceed to “Quick Start” STEP 6, on page 4 of

this Operation Guide.

6SHFL¿FDWLRQVDQG3DFNLQJ,QVWUXFWLRQV

Audio Specifications

Aux Iput Sensitivity

200mV

Aux Input Impedance

10,000 ohms

Subwoofer Output Filter

2,000Hz Low Pass

Subwoofer Output Impedance

200 ohms

Type A connector with Host Mode.

Used for firmware Updates and Network Connec-

tion using a special adapter (see page 2, note 3 for

DGGLWLRQDOLQIRUPDWLRQ

USB Connector

,(((DEJQ:L)L'XDO%DQG:36

Wi-Fi Connectivity

Power Requirements

100-240 Volts, 50/60Hz at 60 Watts

Standby: Less than 0.5 watt

Overall Dimensions

:LGWKLVLQFKHVFP

+HLJKWLVLQFKHVFP

'HSWKLVLQFKHVFPLQFOXGLQJWKH)URQW

Panel and connection cables.

Weight

SRXQGV.JQHWLQFOXGHVWKHH[WHUQDO

3RZHU6XSSO\SRXQGV.JLQVKLSSLQJ

carton

Shipping Carton Dimensions

:LGWKLVLQFKHVFP

+HLJKWLVLQFKHVFP

'HSWKLVLQFKHVFP

General Specifications Packing Instructions

In the event it is necessary to repack the equipment

for shipment, the equipment must be packed exact-

ly as shown below. Failure to do this will result in

shipping damage.

Use the original shipping carton and interior parts

only if they are all in good serviceable condition.

,IDVKLSSLQJFDUWRQRUDQ\RIWKHLQWHULRUSDUWV

are needed, please call or write Customer Service

Department of McIntosh Laboratory. Refer to

page 2. Please see the Part List for the correct part

numbers.

Quantity Part Number Description

1 310573SP Shipping carton only

1 310569SP Left side foam pad

1 310572SP Right side foam pad

1 310570SP Nonwoven bag

1 310571SP Plastic bag

1 310568SP Accessory box

Loudspeaker Specifications

System Driver Complement

2QHLQFK:RRIHU0LGUDQJHZLWKDFRXVWLFSRUW

One 3/4 inch Dome Tweeter

Frequency Response

55Hz - 20kHz

Crossover Frequency

2,000Hz

Enclosure Finish

High Gloss Black

Grille Finish

Black Knit Cloth

Grille Attachment

Magnetic

The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated who reserve the right to

improve design without notice.

The RS100 is designed to employ non-McIntosh-provided services (including but not limited to Play-Fi® and

Wi-Fi®), some of which require separate customer subscriptions and some of which do not, as part of the Products’

functionality. Because McIntosh cannot control the providers of such services or the services themselves, the owner

of the Product therefore assumes all risks related to the use of services provided by anyone other than McIntosh itself.

McIntosh cannot and does not warrant against, and shall have no liability of any kind for any of the following that are

attributable to non-McIntosh providers or services: (i) interruption, discontinuance, or other unsatisfactory performance

of service; (ii) reduced Product functionality that is so attributable; or (iii) any other loss or damage of any kind that is

so attributable.

McIntosh Laboratory, Inc.

2 Chambers Street

Binghamton, NY 13903

www.mcintoshlabs.com

McIntosh Part No. 041661SP

RS100

wireless loudspeaker

www.mcintoshlabs.com

■ The RS100 wireless speaker allows you to easily add streaming

music to any room you want. Just connect it to your Wi-Fi

network and then stream from your mobile device. Auxiliary input

available for non-streaming use.

■ Features DTS Play-Fi® technology to give you the freedom and

exibility to wirelessly play your music at home anyway you want

over your existing Wi-Fi network.

■ Start with one speaker and add more over time. Up to 16

individual speakers can be connected to a single Wi-Fi network -

enough for stereo playback in 8 separate rooms.

■ Stream different music to each room from different mobile

devices, giving each family member or guest control over what

they want to hear in their room.

■ Besides accessing your personal music library, the Apple and

Android apps have built-in support for many leading online

streaming services including Amazon Prime Music, Deezer,

KKBox, Pandora®, QQMusic, Rhapsody, SiriusXM®, Songza,

Spotify® and TIDAL.1

■ Unlike many other streaming solutions, DTS Play-Fi provides

lossless playback of up to 16-bit/48kHz les; it also has playback

support for high-resolution music les up to 24-bit/192kHz.

Easily add streaming music to any room

1. All services may not be available in all regions; certain services may not yet be

enabled for all apps; subscriptions may be required. List subject to change. iPhone shown with DTS Play-Fi app. iPhone not included. Speakers sold individually.

www.mcintoshlabs.com

Companion Products

The RS100 may be added to any existing system or can be the rst piece used to build a luxury audio system.

Your Authorized Dealer can provide additional information on other McIntosh products.

To learn more, please call us at 1.800.538.6576.

35104500

For the Consumer’s Protection:

In order to ensure the highest level of customer satisfaction, “new” McIntosh products may only be purchased over-the-

counter or delivered and installed by an Authorized McIntosh Dealer. McIntosh products that are purchased over the

Internet, by phone or mail order are presumed to be “used” and do not qualify for any McIntosh Warranty. McIntosh does

not warrant, in any way, products that are purchased from anyone who is not an Authorized Dealer or products that have

had their serial number altered or defaced.

RS100

wireless loudspeaker

System Type:

2-way, rear ported wireless bookshelf

speaker with high gloss black nish

Grill:

Magnetically attached black cloth

Power Handling:

60 Watts

Woofer/Midrange:

One 4” long throw under hung voice

coil in a ½” thick top plate, copper

cap for distortion reduction

Tweeter:

One ¾” Titanium dome, magnetic

uid cooled

Response:

55Hz to 20kHz (active high pass)

Sensitivity:

85dB (1w / 1m)

Crossover Frequency:

2,500Hz

Inputs:

1 Unbalanced Analog

Outputs:

1 Unbalanced Analog (for subwoofer)

USB Input:

1 for rmware updates or direct

connection to network via USB-to-

Ethernet adapter (not included)

Control:

Apple or Android mobile app and

Windows desktop app

Embedded Streaming Services in

Apps: Amazon Prime Music, Deezer,

KKBox, Pandora®, QQMusic,

Rhapsody, SiriusXM®, Songza, Spotify®

and TIDAL (all services may not be

available in all regions; certain services

may not yet enabled for all apps;

subscriptions may be required. List

subject to change.)

Overall Dimensions (W x H x D):

8¼” (20.8cm) x 12¾” (32.3cm) x 8”

(20.3cm)

Weight:

15 lbs (6.8 kg) net

17.5 lbs (8 kg) in shipping carton

04166700

HOME ELECTRONICS

THREE YEAR LIMITED WARRANTY

Welcome to the family of McIntosh

owners. This is the Warranty for your

new McIntosh Home Electronic Product

(the “Product”). Your Product has been designed

to give many years of trouble-free performance.

Nonetheless, failures do sometimes occur even

with equipment as well-built as McIntosh’s.

Therefore, please read this Warranty carefully,

because it contains rights, as well as limitations,

exclusions, and obligations, which in the event

of such a failure may be very important to you. If

after reading it thoroughly, you have any questions

about the Warranty, please do not hesitate to write

or telephone McIntosh at the address or phone

number shown on the back of this warranty.

Please note that this is the only Warranty which

McIntosh provides for your Product, and that no

one, including your dealer, has any authority to

either modify or expand upon this Warranty. If

your dealer has offered or made any warranties

or representations concerning the Product which

differ from those contained in this Warranty, they

are strictly between you and the dealer, and will

neither be binding upon McIntosh nor change any

of the provisions in this Warranty. Please also note,

that if your Product ever does require Warranty

service, obtaining such service will be much easier

if you have completed and returned the enclosed

Warranty Registration Card. So please take a

PLQXWHWR¿OORXWDQGUHWXUQWKH5HJLVWUDWLRQ&DUG

now, before you become too distracted by the great

sounds coming from your new McIntosh Product!

Scope and Duration of Warranty

Subject to the terms and conditions stated below, McIntosh Laboratory, Inc. (“McIntosh”) warrants

to the original owner that this Product shall be free from defects in workmanship or materials for a

term of three (3) years from the date when it was purchased from an Authorized McIntosh Dealer.

Provided, however, that rather than the three (3) years of coverage afforded the Product generally, where

applicable, vacuum tubes contained in our Products are warranted for 90 days from the date of purchase,

hard disc drives and projector lamps contained in our Products are warranted for one (1) year from the

date of purchase.

Limitations on Persons and Products Covered by this Warranty

This Warranty and all rights provided here under are limited to the original owner. In the event that the

original owner transfers ownership of the Product prior to expiration of the three-(3) year term, this

Warranty shall terminate in its entirety upon the date of such transfer. In addition, McIntosh does not

warrant in any way Products which are purchased from anyone who is not an Authorized McIntosh

Dealer, or which have had their Serial Numbers altered or defaced. Therefore this Warranty is void

and inapplicable if this Product has been purchased from someone other than an Authorized McIntosh

Dealer, or has had its original Serial Numbers altered or defaced.

Geographical Limitations

This Warranty has been included with a McIntosh Product that is designed, intended to be sold and used

only within the United States and Canada. Accordingly, this Warranty only applies to Products which

are purchased in the United States or Canada, and only applies while such Products are used in the

United States or Canada. Products purchased outside the United States or Canada, and failures occurring

outside the United States or Canada, are not covered by this Warranty.

What McIntosh will do under the Warranty

In the event of any defect covered by this Warranty, McIntosh shall without charge provide all parts,

PDWHULDOVDQGODERUQHFHVVDU\WRUHVWRUHWKH3URGXFWWRLWVRULJLQDOVSHFL¿FDWLRQV$IWHUUHSDLU0F,QWRVK

shall return the Product to its owner at the owner’s expense. In the alternative, McIntosh may at its sole

option either replace the Product without charge, or if replacement is not commercially practicable

or repair or replacement cannot be accomplished within a reasonable time, McIntosh may refund the

purchase price of the Product, subject where appropriate to reasonable depreciation for actual use

in accordance with applicable laws, in full satisfaction of its warranty obligations. McIntosh or its

Authorized Service Agency will undertake to complete the repair and return of the Product as soon as

circumstances permit, unless prevented by causes beyond their reasonable control.

Limitations on McIntosh’s Obligations under the Warranty

McIntosh’s sole Obligation under this Warranty shall be to repair or replace the Product, or at its option

refund the purchase price, as provided for hereinabove. McIntosh does not warrant against, nor shall

it be liable for, any of the following: removal or installation charges; shipping expenses either to or

from McIntosh or its Authorized Service Agency; loss of use; property damage of any kind; or other

incidental or consequential damages or losses of any kind.

Note: Some states do not allow exclusion or limitation of consequential damages, so the foregoing

exclusions may not apply to you.

Parts and Occurrences that are not Covered by the Warranty

This Warranty does not cover any of the following: (a) glass panels, cabinetry, trim, or other appearance

items (except where they are defective at the time of original sale and the Product is delivered for

UHSDLU ZLWKLQ WKH ¿UVW WKLUW\  GD\V WKHUHDIWHU E EDWWHULHV RU GDPDJH WR WKH 3URGXFW FDXVHG E\

failure of batteries; (c) or damage to the Product caused by failure of projector lamp; (d) loss of, or

GDPDJH RU FRUUXSWLRQ WR GLJLWDO GDWD ¿OHV RU RWKHU LQIRUPDWLRQ FRQWHQW RI DQ\ NLQG UHJDUGOHVV RI

cause; (e) failures arising from accident, catastrophe, misuse, neglect, or failure to properly connect

and operate the Product in accordance with the accompanying instructions; (f) failures arising from

improper installation or removal of the Product; or (g) failures arising from any tampering, alteration,

or damage to the Product or attempted servicing of the Product by anyone other than McIntosh or an

Authorized McIntosh Service Agency; and McIntosh shall have no liability or obligation of any kind

with respect to any of the foregoing types of failures.

What the Owner must do to obtain service under this Warranty

To obtain service under this Warranty, the owner must at the owner’s expense arrange for any necessary

de-installation of the Product, and deliver or ship the Product to McIntosh at the address below, or

to an Authorized McIntosh Service Agency, properly packaged, prepaid, and insured at the owner’s

expense. In addition, the owner must provide evidence that the Product is at the time of delivery within

the scope of his Warranty, by either having completed and submitted to McIntosh on a timely basis the

accompanying Warranty Registration Card, or by including the original sales receipt (photocopies are

not acceptable) with the Product when it is delivered for repair.

What the Owner must Pay For

As noted above, the owner must pay any expense of removing the Product from its installation, and

must pay any expenses for delivery of the Product to McIntosh or the Authorized McIntosh Service

Agency. Upon return of the Product to the owner following repair, it shall be the owner’s responsibility

to pay for the shipping charges incurred in return of the Product, as well as to arrange and pay for any

re-installation which may be required. In addition, it shall be the owner’s obligation to pay for any

repairs made to any Product for which the owner has neither completed and submitted the Warranty

Registration Card at the time of purchase nor included the original sales receipt with the Product when

delivered for service, at McIntosh’s or its Authorized Service Agency’s then-current repair rates.

How to learn where the nearest Authorized McIntosh Service Agency is, or

obtain answers to other questions concerning this Warranty

In order to learn the name and address of the nearest Authorized McIntosh Service Agency, obtain

instructions for shipment of a covered Product to McIntosh, or obtain the answers to any other

questions you may have concerning this Warranty, you may telephone McIntosh’s Customer Service

Department between the hours of 9:00 a.m. and 4:30 p.m. Eastern Time, Monday through Friday, at

888-979-3737 (607-723-3512) or write to McIntosh at 2 Chambers Street, Binghamton, New York

13903-2699, Attention: Customer Service Department or visit the “Contact Us” area of the McIntosh

Web Site at www.mcintoshlabs.com.

1RWH7KLV:DUUDQW\JLYHV\RXVSHFL¿FOHJDOULJKWVDQG\RXPD\DOVRKDYHRWKHUULJKWVZKLFKYDU\

from state to state.

McIntosh RS100 Operating instructions

Brand: McIntosh

Model: RS100

Category: Supplementary music equipment

Type: Operating instructions

Download PDF

report

McIntosh RS100 Operating instructions

McIntosh RS100 Operating instructions

Related papers

Other documents