Honeywell STFW12D User manual

OneWireless

XYR 6000 ISA100.11a Compliant

Pressure Transmitter

User's Manual

34-XY-25-43

Revision 3

March 2012

ii OneW

ireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual Revision 3

March 2012

Notices and Trademarks

Revision 3 March 2012

While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied

warranties of merchantability and fitness for a particular purpose and makes no express warranties except as may

be stated in its written agreement with and for its customers.

In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information and

specifications in this document are subject to change without notice.

Honeywell, PlantScape, Experion PKS, and TotalPlant are registered trademarks of Honeywell International Inc.

Other brand or product names are trademarks of their respective owners.

Honeywell Process Solutions

1860 West Rose Garden Lane

Phoenix, Arizona 85027

Revision 3

OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual iii

March 2012

About This Document

This document describes preparation, operation and maintenance of the XYR 6000 Wireless Pressure Transmitters.

Mounting, installation and wiring are covered in other documents.

Honeywell does not recommend using devices for critical control where there is a single point of failure or where

single points of failure result in unsafe conditions. OneWireless is targeted at open loop control, supervisory

control, and controls that do not have environmental or safety consequences. As with any process control solution,

the end-user must weigh the risks and benefits to determine if the products used are the right match for the

application based on security, safety, and performance. Additionally, it is up to the end-user to ensure that the

control strategy sheds to a safe operating condition if any crucial segment of the control solution fails.

Revision Information

Document Name

XYR 6000 ISA100.11a Compliant Pressure

Transmitter User's Manual

Document ID Revision

Number

Publication Date

New 34-XY-25-43 1 January 2011

ISA 100 34-XY-25-43 2 October 2011

Added Flange Mount and Remote Seal data,

updated Approvals information

34-XY-25-43 3 March 2012

References

The following list identifies all documents that may be sources of reference for material discussed in this publication.

Document Title

XYR 6000 Transmitters Quick Start Guide 34-XY-25-21

Getting Started with Honeywell OneWireless Solutions OW-CDX010

OneWireless User’s Guide OW-CDX060

OneWireless Builder Parameter Reference OW-CDX070

iv OneW

ireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual Revision 3

March 2012

Support and contact info

United States and Canada

Contact: Honeywell Process Solution

 Global Technical Support - Phone: 001-800-423-9883

 Customer Service (HFS) - Phone: 001-800-343-0228

 Outside United States - Phone: 001-215-641-3610

Calls are answered by dispatcher between 6:00 am and 4:00 pm Mountain Standard

Time. Emergency calls outside normal working hours are received by an answering

service and returned within one hour.

Email support: [email protected]

Mail: Honeywell Process Solutions

1860 West Rose Garden Lane,

Phoenix, Arizona 85027

For more contact details for Europe, Asia, North and South Americas, please see back page.

World Wide Web

Honeywell Process Solutions Support Online:

www.honeywellprocess.com/

Elsewhere

Call your nearest Honeywell office.

Training Classes

Honeywell Automation College:

http://www.automationcollege.com

Symbol Definitions

The following table lists those symbols used in this document to denote certain conditions.

Symbol Definition

ATTENTION: Identifies information that requires special consideration.

TIP: Identifies advice or hints for the user, often in terms of performing a task.

CAUTION

Indicates a situation which, if not avoided, may result in equipment or work (data) on

the system being damaged or lost, or may result in the inability to properly operate

the process.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury. It may also be used to alert against unsafe

practices.

CAUTION symbol on the equipment refers the user to the product manual for

additional information. The symbol appears next to required information in the

manual.

WARNING: Indicates a potentially hazardous situation, which, if not avoided, could

result in serious injury or death.

WARNING symbol on the equipment refers the user to the product manual for

additional information. The symbol appears next to required information in the

manual.

WARNING, Risk of electrical shock: Potential shock hazard where HAZARDOUS

LIVE voltages greater than 30 Vrms, 42.4 Vpeak, or 60 VDC may be accessible.

ESD HAZARD: Danger of an electro-static discharge to which equipment may be

sensitive. Observe precautions for handling electrostatic sensitive devices.

Protective Earth (PE) terminal: Provided for connection of the protective earth

(green or green/yellow) supply system conductor.

Functional earth terminal: Used for non-safety purposes such as noise immunity

improvement. NOTE: This connection shall be bonded to Protective Earth at the

source of supply in accordance with national local electrical code requirements.

Earth Ground: Functional earth connection. NOTE: This connection shall be

bonded to Protective Earth at the source of supply in accordance with national and

local electrical code requirements.

Chassis Ground: Identifies a connection to the chassis or frame of the equipment

shall be bonded to Protective Earth at the source of supply in accordance with

national and local electrical code requirements.

continued

Revision 3

OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual v

March 2012

vi OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual Revision 3

Symbol Description

The Factory Mutual

®

Approval mark means the equipment has

been rigorously tested and certified to be reliable.

The Canadian Standards mark means the equipment has been

tested and meets applicable standards for safety and/or

performance.

The Ex mark means the equipment complies with the requirements

of the European standards that are harmonised with the 94/9/EC

Directive (ATEX Directive, named after the French "ATmosphere

EXplosible").

For radio equipment used in the European Union in accordance

with the R&TTE Directive the CE Mark and the notified body (NB)

identification number is used when the NB is involved in the

conformity assessment procedure. The alert sign must be used

when a restriction on use (output power limit by a country at certain

frequencies) applies to the equipment and must follow the CE

marking.

The C-Tick mark is a certification trade mark registered to ACMA

(Australian Communications and Media Authority) in Australia under

the Trade Marks Act 1995 and to RSM in New Zealand under

section 47 of the NZ Trade Marks Act. The mark is only to be used

in accordance with conditions laid down by ACMA and RSM. This

mark is equal to the CE Mark used in the European Union.

N314 directly under the logo is Honeywell’s unique supplier

identification number.

The ISA100 Wireless Compliant logo indicates the device has

received ISA100.11a conformance certification and is registered

with the Wireless Compliance Institute, assuring device

interoperability.

CRN Canadian Registration Number

March 2012

Revision 3

OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual vii

March 2012

Contents

Support and contact info........................................................................................................................iv

1. INTRODUCTION....................................................................................................1

1.1 Purpose..........................................................................................................................................1

1.2 Scope..............................................................................................................................................1

1.3 OneWireless network overview...................................................................................................1

1.4 About the transmitter....................................................................................................................1

2. SPECIFICATIONS .................................................................................................3

2.1 European Union Usage.................................................................................................................3

2.2 Certifications and Approvals .......................................................................................................4

Transmitter.............................................................................................................................................................4

Electrical Data: .......................................................................................................................................................8

Battery....................................................................................................................................................................8

DC Supply..............................................................................................................................................................8

2.3 Conditions of Certification...........................................................................................................8

IECEx Conditions of Certification ...........................................................................................................................8

ATEX Conditions for Safe Use...............................................................................................................................8

2.4 Maximum Working Pressure:.......................................................................................................9

Provisioning Device................................................................................................................................................9

2.5 Agency compliance information..................................................................................................9

FCC compliance statements ..................................................................................................................................9

IC compliance statements....................................................................................................................................10

Radio Frequency (RF) statement .........................................................................................................................10

European Union restriction...................................................................................................................................10

Restriction ............................................................................................................................................................10

Japanese Restrictions..........................................................................................................................................10

3. PREPARATION ...................................................................................................11

3.1 Installation ...................................................................................................................................11

3.2 Configuration...............................................................................................................................11

3.3 Connecting to network ...............................................................................................................11

3.4 Calibrating the transmitter.........................................................................................................11

Overview ..............................................................................................................................................................11

Calibrate zero.......................................................................................................................................................11

Procedure for field calibration of Honeywell compound characterized XYR6000 pressure transmitters ..............12

4. FUNCTION BLOCKS...........................................................................................15

4.1 Introduction .................................................................................................................................15

4.2 Block description........................................................................................................................15

Block types...........................................................................................................................................................15

Block diagram.......................................................................................................................................................15

4.3 Parameter details ........................................................................................................................16

Contents

Symbol Definitions

viii OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual Revision 3

March 2012

5. OPERATION........................................................................................................17

5.1 Overview ......................................................................................................................................17

Display modes .....................................................................................................................................................17

Provisioning Device..............................................................................................................................................17

5.2 Transmitter connection status...................................................................................................18

5.3 Transmitter PV display ...............................................................................................................19

5.4 Transmitter quick view of parameters ......................................................................................25

5.5 Transmitter menu........................................................................................................................26

Menu tree.............................................................................................................................................................26

5.6 Provisioning Device menus .......................................................................................................27

Overview..............................................................................................................................................................27

Main menu...........................................................................................................................................................27

Security and Node Deployment ...........................................................................................................................28

Device Local Configuration..................................................................................................................................30

Read Device Information......................................................................................................................................31

Advanced Options................................................................................................................................................33

6. MAINTENANCE/REPAIR ....................................................................................35

6.1 Introduction .................................................................................................................................35

6.2 Preventive maintenance.............................................................................................................35

6.3 Inspecting and cleaning barrier diaphragms...........................................................................35

Tools required......................................................................................................................................................35

Procedure ............................................................................................................................................................36

Torque ratings......................................................................................................................................................37

6.4 Replacing sensor module ..........................................................................................................38

Tools required......................................................................................................................................................38

Procedure ............................................................................................................................................................38

6.5 Replacing batteries.....................................................................................................................40

When to replace...................................................................................................................................................40

Tools required......................................................................................................................................................40

Procedure ............................................................................................................................................................40

IS Battery Pack replacement procedure...............................................................................................................41

6.6 Replacing 24V external power module .....................................................................................42

When to replace...................................................................................................................................................42

Tools required......................................................................................................................................................42

Procedure ............................................................................................................................................................42

24V External power module.................................................................................................................................44

6.7 Replacing antenna ......................................................................................................................45

Tools required......................................................................................................................................................45

Procedure ............................................................................................................................................................45

Antenna replacement procedure..........................................................................................................................46

6.8 Parts .............................................................................................................................................48

Transmitter body..................................................................................................................................................48

Meter body...........................................................................................................................................................49

6.9 Dimension drawings...................................................................................................................54

APPENDIX A - MODBUS .............................................................................................55

Contents

Tables

Revision 3 OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual ix

March 2012

Tables

Table 2-1 European Union Usage.................................................................................................................3

Table 2-2 Certifications and Approvals..........................................................................................................4

Table 3-1 Calibrate zero..............................................................................................................................12

Table 4-1 Blocks..........................................................................................................................................15

Table 5-1 Transmitter connection status.....................................................................................................18

Table 5-2 Transmitter PV display ................................................................................................................19

Table 5-3 XYR 6000 DP units......................................................................................................................19

Table 5-4 XYR 6000 Flow units...................................................................................................................20

Table 5-5 PV status.....................................................................................................................................22

Table 5-6 Device status...............................................................................................................................22

Table 5-7 Transmitter quick view of parameters .........................................................................................25

Table 5-8 Menu tree ....................................................................................................................................26

Table 5-9 Buttons for Device Local Configuration.......................................................................................30

Table 5-10 Read Device Information...........................................................................................................31

Table 5-11 Advanced Options.....................................................................................................................34

Table 6-1 Inspecting and Cleaning Barrier Diaphragms .............................................................................36

Table 6-2 Process Head Bolt Torque Ratings.............................................................................................37

Table 6-3 Sensor module replacement .......................................................................................................38

Table 6-4 Transmitter Body Parts................................................................................................................48

Table 6-5 Parts (see Figure 6-7, Figure 6-8)..............................................................................................50

Table 6-6 Parts (see Figure 6-9) .................................................................................................................53

Table 6-7 Drawing numbers for DP models STDW1xx, STDW9xx.............................................................54

Table 6-8 Drawing numbers for DHGP models STGW944, STGW974......................................................54

Table 6-9 Drawing numbers for GP/AP models STAW1xL , STGW9xL, STGW1xL, STGW9xL................54

Table 6-10 Drawing Numbers for Flush, Extended and Pseudo Flanged Models......................................54

Table 6-11 Drawing Numbers for DP Remote Seal Models STRW1xD, STRW9xD...................................54

Table 6-12 Drawing Numbers for GP/AP Remote Seal Models STRW1xG, STRW9xG, STRW1xA,

STRW9xA.............................................................................................................................................54

Table 6-13 – XYR 6000 Pressure Analog In – Modbus table......................................................................55

Table 6-14 XYR 6000 Pressure – Modbus table.........................................................................................58

Contents

Figures

x OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual Revision 3

March 2012

Figures

Figure 1-1 XYR 6000 Functional Diagram....................................................................................................2

Figure 4-1 Block Diagram............................................................................................................................15

Figure 5-1 Main menu..................................................................................................................................27

Figure 5-2 Security and Node Deployment .................................................................................................28

Figure 5-3 Device Local Configuration screen ............................................................................................30

Figure 5-4 Read Device Information............................................................................................................31

Figure 5-5 Advanced Options......................................................................................................................33

Figure 6-1 Assembly of DP Transmitter Process Heads.............................................................................37

Figure 6-2 Sensor module removal and replacement.................................................................................39

Figure 6-3: IS Battery Pack..........................................................................................................................41

Figure 6-4 24V Power Supply Module Assembly........................................................................................43

Figure 6-5 24V External power module.......................................................................................................44

Figure 6-6 Antenna replacement.................................................................................................................47

Figure 6-7 STDW1xx, STDW9xx.................................................................................................................49

Figure 6-8 STGW944, STGW974................................................................................................................49

Figure 6-9 STAW1xL, STAW9xL, STGW1xL, STGW9xL ...........................................................................53

1. Introduction

1.1. Purpose

Revision 3 OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual 1

March 2012

1. Introduction

1.1 Purpose

This manual describes the Honeywell OneWireless XYR 6000 Pressure Transmitter function, operation

and maintenance.

1.2 Scope

The manual includes:

 Details of topics that relate uniquely to the Honeywell XYR 6000 Pressure Transmitter,

 This manual does not cover installation, mounting, or wiring. See XYR 6000 Transmitter Quick Start

Guide (document 34-XY-25-21).

1.3 OneWireless network overview

OneWireless is an all digital, serial, two-way communication mesh network that interconnects industrial

field sensors to a central system.

OneWireless has defined standards to which field devices and operator stations communicate with one

another. The communications protocol is built as an "open system" to allow all field devices and

equipment that are built to OneWireless standard to be integrated into a system, regardless of the device

manufacturer. This interoperability of devices using OneWireless technology is to become an industry

standard for automation systems.

1.4 About the transmitter

The XYR 6000 Pressure Transmitter is furnished with an ISA100.11a-compliant wireless interface to

operate in a compatible distributed ISA100.11a wireless system. The transmitter will interoperate with

any ISA100.11a wireless network.

The transmitter includes

ISA100.11a-compliant electronics for operating in a 2.4GHz wireless network. It

features function block architecture and instantiable input channels.

The XYR 6000 Pressure Transmitter comes in a variety of models for measurement applications involving

one of these basic types of pressure:

 Differential pressure,

 Gauge pressure,

 Absolute pressure.

The transmitter measures the process pressure and transmits the measured value as a digital output signal

in user-configured engineering units. Its major components are an electronics housing and a meter body as

shown in Figure 1-1 (a typical differential pressure model transmitter).

The

XYR 6000 transmits its output in a digital OneWireless protocol format for direct digital

communications with systems.

The Process Variable (PV) is available for monitoring and alarm purposes. Available PV update rates: 1, 5,

10, 30 seconds and are set on the OneWireless User Interface. Slower update rates extend battery life. The

meter body temperature is also available as a secondary variable for monitoring. Figure 1-1 shows a block

di

ag

ram of the XYR 6000 Pressure transmitter’s operating functions.

1. Introduction

1.4. About the transmitter

The XYR 6000 Pressure DP model type is capable of measuring mass flow and volumetric flow. When

minimum and maximum flow rate values are configured as PV scale 0% and 100% values at given PV

units of measure, and the respective DP values at those limits are configured as the calibration scale 0%

and 100% values, the PV value becomes a flow rate in the selected units of measure. Minimum and

maximum flow rate data at given DP values is either provided on or with orifice plates, or is commonly

available according to orifice plate size.

EEPROM

A/D

DP or AP

Sensor

SP

Sensor

Temp

Sensor

Multi-

plexer

Electronics Housing

Meter Body

Radio

Board

Pressure

Input

Micro-

processor

Micro-

processor

EEPROM

Factory

Characterization

Data

Configuration

Data

Battery

Antenn

a

Measurement

Board

Configuration

Data

Figure 1-1 XYR 6000 Functional Diagram

2 OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual Revision 3

March 2012

2. Specifications

2.1. European Union Usage

Revision 3 OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual 3

March 2012

2. Specifications

2.1 European Union Usage

This product may be used in any of the following European Union nations.

Table 2-1 European Union Usage

Country

ISO 3166

2 letter code

Country

ISO 3166

2 letter code

Austria AT Latvia LV

Belgium BE Liechtenstein LI

Bulgaria BG Lithuania LT

Cyprus CY Malta MT

Czech Republic CZ Netherlands NL

Denmark DK Norway NO

Estonia EE Poland PL

Finland FI Portugal PT

France FR Romania RO

Germany DE Slovakia SK

Greece GR Slovenia SI

Hungary HU Spain ES

Iceland IS Sweden SE

Ireland IE Switzerland CH

Italy IT United Kingdom BG

2. Specifications

2.2. Certifications and Approvals

4 OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual Revision 3

March 2012

2.2 Certifications and Approvals

Transmitter

Refer to product lable for applicable ratings.

Table 2-2 Certifications and Approvals

AGENCY TYPE OF PROTECTION Ambient

Temperature

Product Applicability*

Intrinsically Safe:

Class I; Division 1; Groups A, B, C, D;

Class II, Division 1, Groups E, F, G;

Class III, Division 1; T4

Class I, Zone 0 Ex ia IIC T4

Class I, Zone 0 AEx ia IIC T4

-40

o

C to +85

o

C : Battery

-40

o

C to +80

o

C : DC

Supply

Pressure

Temperature/ Discrete

Inputs

Corrosion

High Level INPUT (HLAI)

Universal I/O

Nonincendive:

Class I; Division 2; Groups A, B, C, D;

Class II, Division 2, Groups F, G;

Class III, Division 2, T4

Class I, Zone 2 Ex nA IIC, T4

Class I, Zone 2 AEx nA IIC, T4

-40

o

C to +85

o

C : Battery

-40

o

C to +80

o

C : DC

Supply

Pressure

Temperature/ Discrete

Inputs

High Level INPUT (HLAI)

Universal I/O

Explosion-Proof/ Flameproof:

Class I, Division 1; Groups A, B, C, D;

Class II, Division 1, Groups E, F, G;

Class III, Division 1; T4

Class I, Zone 1 Ex d IIC T4

Class I, Zone 1 AEx d IIC, T4

40

o

C to +85

o

C : Battery

-40

o

C to +80

o

C : DC

Supply

Pressure

Temperature/ Discrete

Inputs

Corrosion

High Level INPUT (HLAI)

Universal I/O

Enclosure: Type 4X/ IP66

CSA

1903673

(USA and

Canada)

Standards Used:

CSA-C22.2 No. 30:M1986

CSA-C22.2 No. 94:M1991

CSA E60079-0: 2002

CSA E60079-15: 2002

FM 3600: 1998

FM 3615: 2006

UL 916:1998

CSA-C22.2 No. 142:M1987

CSA-C22.2 No. 157:M1992

CSA E60079-1: 2002

CSA E61241-0: 2002

FM 3610: 1999

ANSI/ ISA 12.12.02: 2003

CSA-C22.2 No. 213:M1987

CSA-C22.2 No. 60529:2005

CSA E60079-11: 2002

CSA E61241-1: 2002

FM 3611: 2004

UL 50:2003

2. Specifications

2.2. Certifications and Approvals

Revision 3 OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual 5

March 2012

AGENCY TYPE OF PROTECTION Ambient

Temperature

Product Applicability*

Intrinsically Safe:

Class I; Division 1; Groups A, B, C, D;

Class II, Division 1, Groups E, F, G;

Class III, Division 1; T4

Class I, Zone 0 AEx ia IIC T4

-40

o

C to +85

o

C : Battery

-40

o

C to +80

o

C : DC

Supply

Pressure

Temperature/ Discrete

Inputs

Corrosion

High Level INPUT (HLAI)

Universal I/O

Nonincendive:

Class I; Division 2; Groups A, B, C, D;

Class II, Division 2, Groups F, G;

Class III, Division 2, T4

Class I, Zone 2 AEx nA IIC, T4

-40

o

C to +85

o

C : Battery

-40

o

C to +80

o

C : DC

Supply

Pressure

Temperature/ Discrete

Inputs

High Level INPUT (HLAI)

Universal I/O

Explosion-Proof/ Flameproof:

Class I, Division 1; Groups A, B, C, D;

Class II, Division 1, Groups E, F, G;

Class III, Division 1; T4

Class I, Zone 1 AEx d IIC, T4

-40

o

C to +85

o

C : Battery

-40

o

C to +80

o

C : DC

Supply

Pressure

Temperature/ Discrete

Inputs

Corrosion

High Level INPUT (HLAI)

Universal I/O

Enclosure: Type 4X/ IP66

FM

ApprovalsTM

3032450

(USA)

Standards Used:

FM 3600:1998

FM 3615:2006

ANSI/ ISA 12.02.01: 2002

ANSI/ IEC 60529: 2004

FM 3610: 2007

FM 3810: 2005

ANSI/ ISA 12.12.02: 2003

ANSI/ NEMA 250: 2003

FM 3611: 2004

ANSI/ ISA 12.00.01: 2002

ANSI/ ISA 12.22.01: 2005

AGENCY TYPE OF PROTECTION Ambient

Temperature

Product Applicability*

Intrinsically Safe:

II 1 G Ex ia IIB T4

II 1 D Ex tD A20 IP66 T90 oC

-40

o

C to +70

o

C: Battery

-40

o

C to +80

o

C : DC

Supply

Pressure

Temperature/ Discrete

Inputs

Corrosion

High Level INPUT (HLAI)

Universal I/O

Flameproof:

II 2 G Ex d [ia] IIB T4

II 2 D Ex tD A21 IP66 T90 oC

-40

o

C to +70

o

C: Battery

-40

o

C to +80

o

C : DC

Supply

Pressure

Corrosion

High Level INPUT (HLAI)

Universal I/O

Enclosure: IP66

ATEX- KEMA

08ATEX0062X

Standards Used:

EN 60079-0 : 2006

EN 60079-26 : 2007

EN 60079-1 : 2004

EN 61241-0 : 2006

EN 60079-11 : 2007

EN 61241-1 : 2004

2. Specifications

2.2. Certifications and Approvals

6 OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual Revision 3

March 2012

AGENCY TYPE OF PROTECTION Ambient

Temperature

Product Applicability*

Nonincendive:

II 3 G Ex nA [nL] IIC T4

II 3 D Ex tD A22 IP66 T90 oC

-40

o

C to +84

o

C

Pressure

Temperature/ Discrete

Inputs

Corrosion

High Level INPUT (HLAI)

Universal I/O

Enclosure: IP66

ATEX-

DEKRA

08ATEX0074

Standards Used:

EN 60079-0 : 2006

EN 61241-1 : 2004

EN 60079-15 : 2005

EN 61241-0 : 2006

AGENCY TYPE OF PROTECTION Ambient

Temperature

Product Applicability*

Intrinsically Safe:

Ex ia IIB T4

Ex tD A20 IP66 T90 oC

-40

o

C to +70

o

C: Battery

-40

o

C to +80

o

C : DC

Supply

Pressure

Temperature/ Discrete

Inputs

Corrosion

High Level INPUT (HLAI)

Universal I/O

Flameproof:

Ex d [ia] IIB T4

Ex tD A21 IP66 T90 oC

-40

o

C to +70

o

C: Battery

-40

o

C to +80

o

C : DC

Supply

Pressure

Corrosion

High Level INPUT (HLAI)

Universal I/O

Nonincendive:

Ex nA [nL] IIC T4

Ex tD A22 IP66 T90 oC

-40

o

C to +84

o

C: Battery

-40

o

C to +80

o

C : DC

Supply

Pressure

Temperature/ Discrete

Inputs

Corrosion

High Level INPUT (HLAI)

Universal I/O

Enclosure: IP66

IECEx- CSA

09.0001X

Standards Used:

IEC 60079-0 : 2004

IEC 60079-26 : 2007

IEC 60079-15 : 2001

IEC 60079-1 : 2003

IEC 61241-0 : 1999

IEC 60079-11 : 1999

IEC 61241-1 : 1999

2. Specifications

2.2. Certifications and Approvals

Revision 3 OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual 7

March 2012

AGENCY TYPE OF PROTECTION Ambient

Temperature

Product Applicability*

Intrinsically Safe:

Ex ia IIB T4

Ex tD A20 IP66 T90 oC

-40 oC to +70 oC: Battery

-40 oC to +80 oC : DC

Supply

Pressure

Temperature/ Discrete

Inputs

Corrosion

High Level INPUT (HLAI)

Universal I/O

Flameproof:

Ex d [ia] IIB T4

Ex tD A21 IP66 T90 oC

-40 oC to +70 oC: Battery

-40 oC to +80 oC : DC

Supply

Pressure

Corrosion

High Level INPUT (HLAI)

Universal I/O

Nonincendive:

Ex nA [nL] IIC T4

Ex tD A22 IP66 T90 oC

-40

o

C to +84

o

C: Battery

-40

o

C to +80

o

C : DC

Supply

Pressure

Temperature/ Discrete

Inputs

Corrosion

High Level INPUT (HLAI)

Universal I/O

Enclosure: IP66

SAEx

S/09-036X

(South

Africa)

Standards Used:

SANS (IEC) 60079-0 : 2005

IEC 60079-1 : 2003

IEC 61241-0 : 1999

SANS (IEC) 60079-15 : 2006

IEC 60079-11 : 1999

IEC 61241-1 : 1999

ARP 0108 (Edition 1.1)

IEC 60079-26 : 2007

AGENCY TYPE OF PROTECTION Ambient

Temperature

Product Applicability*

Intrinsically Safe:

Ex ia IIB T4 Ga

-40

o

C to +70

o

C: Battery

-40

o

C to +80

o

C : DC

Supply

Pressure

Temperature/ Discrete

Inputs

Corrosion

High Level INPUT (HLAI)

Universal I/O

Flameproof:

Ex d [ia] IIB T4

Ex tb IIIC T90 oC IP66

-40

o

C to +70

o

C: Battery

-40

o

C to +80

o

C : DC

Supply

Pressure

Corrosion

High Level INPUT (HLAI)

Universal I/O

Nonincendive:

Ex nA [ic] IIC T4

Ex tc IIIC T90 oC IP66

-40

o

C to +84

o

C: Battery

-40

o

C to +80

o

C : DC

Supply

Pressure

Temperature/ Discrete

Inputs

Corrosion

High Level INPUT (HLAI)

Universal I/O

Enclosure: IP66

INMETRO**

NCC 11.0331

X

(BRAZIL)

Standards Used:

ABNT NBR IEC 60079-0:2008

IEC 60079-15:2010

ABNT NBR IEC 60529:2009

ABNT NBR IEC 60079-1:2009

ABNT NBR IEC 60079-26:2008

IEC 61241-0 : 1999

ABNT NBR IEC 60079-11:2009

IEC 60079-31:2008

IEC 61241-1 : 1999

*See individual Product manuals as defined in References for exact Models

** At time of Printing Certification was pending.

2. Specifications

2.3. Conditions of Certification

8 OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual Revision 3

March 2012

Electrical Data:

Battery

Two in series connected (D size) Lithium batteries, type 5930 manufactured by Tadiran, type XL-205F

manufactured by Zeno Energy or type PT-2300H manufactured by Eagle Picher.

Additionally for ATEX and IECEx certifications, Lithium Battery SL-2780, manufactured by Tadiran,

GmbH may be used.

DC Supply

For Ordinary Locations, Explosion-proof and Non Incendive:

16.0 V min to 28.0 V max, Current = 100 mA

For Intrinsically Safe:

A Barrier, MTL 728P+ or MTL 7728P+ mounted in a suitable enclosure, or in a non-hazardous

location is needed, see Agency Certification drawings in Section 6.

For Output parameters associated with Temperature/ Discrete Inputs, Corrosion, High Level INPUT

(HLAI) or Universal I/O, see Agency Certification drawings in Section 6.

2.3 Conditions of Certification

IECEx Conditions of Certification

Parts of the antenna are non-conducting and the area of the non-conducting part exceeds the maximum

permissible areas for Category ll 1 G (Zone 0) according to IEC 60079-0. Therefore when the antenna is

used within a potentially explosive atmosphere, appropriate measures must be taken to prevent

electrostatic discharge.

Impact and friction hazards need to be considered according to IEC 600079-0 when the transmitter that is

exposed to the exterior atmosphere is made of light metal alloys, and used in Category ll 1 G (Zone 0).

ATEX Conditions for Safe Use

Because the enclosure of the XYR 6000 Wireless Transmitter is made from aluminum, if it is mounted in

an area where the use of category 1G apparatus is required, it must be installed such that even in the event

of rare incidents, ignition sources due to impact and friction sparks are excluded.

Special precautions shall be taken to prevent the surface of the antenna of the XYR 6000 Wireless

Transmitter from being electrostatically charged.

2. Specifications

2.4. Maximum Working Pressure:

2.4 Maximum Working Pressure:

See individual Product manuals as defined in References.

For detailed transmitter specifications see the following Specification and Model Selection Guides.

 Differential Pressure - S900, document number 34-XY-03-22

 Absolute Pressure - S900, document number 34-XY-03-23

 Gauge Pressure - S90, document number 0 34-XY-03-24

 Flange Mount Spec - S900, document number 34-XY-03-27

 Remote Seal Spec -S900, document number 34-XY-03-28

 Differential Pressure - S100, document number 34-XY-03-44

 Absolute Pressure - S100, document number 34-XY-03-45

 Gauge Pressure - S100, document number 34-XY-03-46

 Flange Mount Spec - S100, document number 34-XY-03-47

 Remote Seal Spec - S100, document number 34-XY-03-48

Provisioning Device

Install the Provisioning Device application on any PDA having

 Windows Mobile version 4.2+

 Infrared port.

2.5 Agency compliance information

This section contains the Federal Communications Commission (FCC), Industry Canada (IC) and Radio

Frequency compliance statements for the OneWireless XYR 6000 Wireless Transmitters device.

ATTENTION

XYR 6000 units must be professionally installed in accordance with the requirements

specified in the OneWireless XYR 6000 Agency Compliance Professional Installation Guide.

FCC compliance statements

 This device complies with Part 15 of FCC Rules and Regulations. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference and (2) this device must

accept any interference received, including interference that may cause undesired operation.

 This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radiofrequency energy and, if not installed and used in accordance with these instructions, may

cause harmful interference to radio communications. Operation of this equipment in a residential area

is likely to cause harmful interference in which case the user will be required to correct the

interference at own expense.

Revision 3 OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual 9

March 2012

2. Specifications

2.5. Agency compliance information

10 OneWireless XYR 6000 ISA100.11a Compliant Pressure Transmitter User's Manual Revision 3

March 2012

 Intentional or unintentional changes or modifications must not be made to the XYR 6000 Wireless

Transmitters unless under the express consent of the party responsible for compliance. Any such

modifications could void the user’s authority to operate the equipment and will void the

manufacturer’s warranty.

IC compliance statements

 To reduce potential radio interference to other users, the antenna type and its gain should be so chosen

that the equivalent isotropic radiated power (EIRP) is not more than that permitted for successful

communication.

 Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation

of the device.

 This Class A digital apparatus complies with Canadian ICES-003.

 French: Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Radio Frequency (RF) statement

To comply with FCC’s and Industry Canada’s RF exposure requirements, the following antenna

installation and device operating configurations must be satisfied.

 Remote Point-to-Multi-Point antenna(s) for this unit must be fixed and mounted on outdoor permanent

structures with a separation distance between the antenna(s) of greater than 20cm and a separation

distance of at least 20cm from all persons.

 Remote Fixed Point–to-Point antenna(s) for this unit must be fixed and mounted on outdoor

permanent structures with a separation distance between the antenna(s) of greater than 20cm and a

separation distance of at least 100cm from all persons.

 Furthermore, when using integral antenna(s) the XYR 6000 Wireless Transmitter unit must not be co-

located with any other antenna or transmitter device and have a separation distance of at least 20cm

from all persons.

European Union restriction

France restricts outdoor use to 10mW (10dBm) EIRP in the frequency range of 2,454-2,483.5 MHz.

Installations in France must limit EIRP to 10dBm, for operating modes utilizing frequencies in the range of

2,454 – 2,483.5MHz.

Restriction

France restricts outdoor use to 10mW (10dBm) EIRP in the frequency range of 2,454-2,483.5 MHz.

Installations in France must limit EIRP to 10dBm, for operating modes utilizing frequencies in the range of

2,454 – 2,483.5MHz.



Japanese Restrictions

For locations in Japan the transmitter power is restricted to 12.14dBm/Mhz {(32mW (15.4 dBm)]

maximum EIRP including the antenna.

Page is loading ...

Honeywell STFW12D User manual

This manual is also suitable for

Honeywell STFW12D User manual

Related papers

Other documents