E-Bike Bofeili Owner's manual

Bofeili e-Bike

Owner’s Manual

Distributed by e-Bikes USA

2

www.BofeiliUSA.com © e-Bikes USA 2012

General Warning

Due to the nature of e-Bikes, they should only be ridden by those ages 16 & older. Be sure you have

tested the e-Bike in a safe environment prior to use around automobile and/or pedestrian traffic. Always

check your equipment prior and during your ride and follow all information below for your safety.

Read the following information entirely before use.

The Manufacturer of Bofeili e-Bikes

The e-bikes are made by Suzhou Bofeili Electric Technology Co Ltd, established in August 2007 in

China, a high-tech enterprise integrating research and development, production and sale. The

company exports to countries throughout the world and employs around 100 staff, concentrating on the

development of electric bicycles and associated electronics. Suzhou Bofeili Electric Technology Co Ltd

commits itself to supplying high quality, highly reliable, cost effective products in a wide range of

industry solutions with technological innovation and product research in order to meet ever changing

market demands.

e-Bike General Use

The bike can be operated in 3 modes: Twist (thumb) throttle, pedal assist or pedal only.

1. Throttle mode comes in handy if you

are starting uphill, or do not want to pedal.

2. In pedal assist mode the bike senses

that you are pedaling (after 2 revolutions) and

starts to help you. 3 Levels of assistance can be

selected. In its highest assist setting, hardly any

user input is required.

3. No resistance from the motor at all

(freewheel clutch) when used as an ordinary

bike.

3

www.BofeiliUSA.com © e-Bikes USA 2012

Safety First

e-Bike riding can be one of your most pleasurable experiences in the outdoors, but you should always

keep safety first.

Wear an approved bicycle helmet. e-Bikes can have speeds up to 20 mph on battery alone;

faster speeds can be achieved by pedaling in addition to the battery power. Unlimited number of

surface variables can cause you to lose control and crash. Watch out for loose rocks, glass, oil, excess

water, grates/man-hole-covers, broken pavement, etc. that can cause the tires friction loss.

Mechanical Safety Check

Routine inspection of the e-Bike and its various fasteners, tire condition, and frame integrity prior to your

day’s activities is a good practice to avoid problems. Most of the fasteners are metric and will need

metric tools to tighten. Make sure that tires are neither over inflated nor under inflated. Check that the

battery is charged sufficiently for your anticipated distance ride. Test the chain and derailleur to be sure

that changing speeds will not cause any problems.

Safety Ride

Initial Test Ride: Select an environment free from hazards or distractions to test your new e-

Bike. Pedestrian or automobile traffic is not the best place to learn the different modes of using the e-

Bike power or pedaling combination. Although similar to riding a normal bicycle, the e-Bike is different

and requires that you are familiar with the throttle, mode selection, power on/off switch on the e-Bike

control and the battery itself.

Basics

Planning ahead is one of the best ways to avoid problems. Think about the path or road you will be

traveling and if there are places where it would be safest to get off and walk your e-Bike. Narrow paths

shared with other bicycles or pedestrians can cause incident and injury if you don’t first anticipate

possible problems. Use the e-Bike’s bell to alert other bicycles or pedestrians that can’t or don’t see you.

Be responsible to give-way to others, especially pedestrians and vehicles that are larger than you.

Bicycle Laws

Always obey the local bicycle and traffic laws. Obey all traffic lights and stop signs. Some bicycle paths

may prohibit motorized vehicles which would require you to use only the pedal mode of your e-Bike.

Check with local law enforcement for clarification of any other limitations. The e-Bike is manufactured

4

www.BofeiliUSA.com © e-Bikes USA 2012

to have a maximum battery powered speed of 20 MPH. Check your state and local laws for e-Bike laws

and statutes.

Sharing the Road

Using an awareness of automobiles and trucks, enjoy the road with the consideration that at times

visibility or constraints on both bikes and larger vehicles may cause difficult situations. Anticipate and

stay aware. Avoid impairing your hearing or vision that may interrupt warning signals, signs, or horns.

Equally, use your e-Bike with awareness of pedestrians, always yielding to those standing, walking or

running.

Off Road

The Bofeili Sport model is designed for trail riding and is not considered a “Mountain Bike”. The Sport

model is not designed for jumps or trick riding. Enjoy the trails and watch for pedestrians walking the

trails. Always leave the trails in as good or better shape than you found them. Do not venture off the

trails with this model or the City or Folding Touring models which are designed for pavement and gravel

roads.

Wet Weather Riding

Although the motor is protected, DO NOT ride through deep water which could damage the motor and/or

controller. Do not expose the battery to extended periods of weather when not riding. Make efforts to

protect electrical connections from excess water. Do not wash the e-bike with water; only use a dry or

damp cloth to clean the frame and parts.

Night Riding

Though the City and Folding Touring e-Bikes are equipped with lights and reflectors, be sure to wear

high-visibility clothing and additional reflective items. Poor visibility of the road can lead to accidents

with the e-Bike at dangerous speeds. ALWAYS WEAR AN APPROVED BIKE HELMET.

Warning Regarding Modifications and/or Additions

Modifications or additions to the e-Bike that are not approved or misuse will void any manufacturers’ or

dealer warranty of any component or the Bofeili e-Bike.

5

www.BofeiliUSA.com © e-Bikes USA 2012

Bofeili GR-201 Model Folding Touring e-Bike

Specifications:

 Patented Intelligent mid-position crankshaft brushless motor

 Shimano 7-speed derailleur provides speed/torque adjustments

 3 modes of operation, Low, Medium & High

 44 lbs. ready to go

 20 Inch wheels

 Panasonic cell lithium-4 ion battery; "flat brick" shape in locking cargo rack. Battery chargeable

on or off the bike.

 >8 degree hill climbing with pedal assistance

 V brakes front and rear.

 Folding Kick-stand

 Comfortable seat.

 Head light and tail reflector

 Rated 20-30 mile range under good conditions using battery power alone (range is greatly

enhanced with pedal assistance)

 Motor power only give maximum 20 MPH

 Only 44 lbs. (incl. battery) one of the lighter full size electric bikes on the market today

 Load rated at 225 lbs.

6

www.BofeiliUSA.com © e-Bikes USA 2012

Bofeili Sport Model

Specifications:

 Patented Intelligent mid-position crankshaft brushless motor

 Shimano 21-speed derailleur (USES MOTOR TORQUE AND HUMAN POWER)

 26 inch wheels x 1.95 inch wide for comfortable ride .

 Panasonic cell lithium-4 ion battery. “Drink Bottle" shape

 Disc brakes front and rear.

 Front fork shocks

 >8 degree hill climbing with pedal assistance

 Sleek styling with well integrated components.

 Rated 20-30 mile range under good conditions using battery power alone (range is greatly

enhanced with pedal assistance)

 Motor power only give maximum 20 MPH

 Only 55 lbs. (incl. battery) one of the lighter full size electric bikes on the market today

 Load rated 225 lbs.

7

www.BofeiliUSA.com © e-Bikes USA 2012

Bofeili City Cruiser Model

Specifications:

 Patented Intelligent mid-position crankshaft brushless motor

 Shimano 7-speed derailleur provides speed/torque adjustments

 3 modes of operation, Low, Medium & High

 28 Inch wheels 700x40C

 Panasonic cell lithium-4 ion battery; "flat brick" shape in locking cargo rack. Battery chargeable

on or off the bike.

 >8 degree hill climbing with pedal assistance

 V brakes front and rear.

 Comfortable seat.

 Head and tail light

 30 mile range under good conditions using battery power alone (range is greatly enhanced with

pedal assistance)

 Motor power only give maximum 20 MPH

 Only 55 lbs. (incl. battery) one of the lighter full size electric bikes on the market today

 Load rated at 225 lbs.

8

www.BofeiliUSA.com © e-Bikes USA 2012

Bike Fit

With the step-thru styled City e-Bike and the Folding Touring e-Bike, bar height is not an issue, but be

sure that with the Sport e-Bike that when standing over the bike in front of the saddle, there is at least 1”

or more of clearance of the rider inseam and the e-Bike bar (as shown in the picture). Adjust the saddle

and the handle-bars for the most comfortable ride. Optimum leg extension is about 75% so there will be

some bend at the knee left in your leg.

The Saddle height is

adjustable with a Cam Action

Adjustment. The pitch is

adjustable using a metric

wrench.

The Handle Bars on some

models also have Cam Action

Adjustment for height and a friction spline adjustment for pitch.

Knowing your e-Bike

Wheels

The front wheel has a Cam Action attachment which must be very tight to prevent the

axle from coming loose from the forks. You may need to seek another person if you are unable to

perform the tightening yourself. The wheels should be turned to ensure there is no rubbing or wobbling.

Hitting curbs or other obstructions can bend or twist the wheels causing unsafe conditions for ridding. If

this occurs, take your e-Bike to a qualified bicycle repair shop and do not attempt to straighten yourself.

This requires special tools and training.

Brakes

Your e-Bike comes equipped with front and rear brakes and each has a hand grip to activate the brake.

Your e-Bike has either friction or disc brakes. In most cases, using both brakes with equal pressure is the

best way to slow down or stop. In down-hill riding, excessive front brake use can cause the bike wheel to

lock and the bike to plunge forward, throwing the rider off and possible serious injury. Know which hand

grip is for the front and rear.

Adjusting the Brakes:

9

www.BofeiliUSA.com © e-Bikes USA 2012

If rubbing occurs of one of the brake pads, first check that the wheel is properly running true. If not,

adjust on the forks. The friction style brakes exert the most stopping power at the point just before

locking the wheel in place. Rain, oil, or wet conditions will cause less friction and therefore you should

anticipate longer braking time than in dry conditions. The pads should be adjusted to strike the wheel rim

with the maximum amount of rubber to wheel alignment. Pads do wear over time and should be reviewed

in your routine inspections.

Your Bofeili e-Bike is equipped with quick adjusting brake cable nuts near the handle grips. Loosen the

locking nut and twist the adjustment nut to shorten or lengthen the cable which will draw the brake pads

closer or further from the wheel rim.

Fine adjustments of the brake arms can be done with a small

screwdriver tightening or loosening the Spring Adjustment Screw

locate as the diagram indicates. Adjust using small amounts.

Tektro brakes on the Sport e-Bike

The Sport model e-Bike has hydraulic disc brakes designed and

manufactured by Tektro. Service information, adjustment and

maintenance for these brakes can be found at www.Tektro.com.

Please match the exact model on the individual e-Bike to the

service and use on the Tektro company web site.

Controls

The Bofeili e-Bike is equipped with a right hand throttle that twists, similar to a motorcycle throttle.

When the power mode is on, the controller will sense the need for electric assistance after the second

pedal revolution and provide assistance depending on your level set, “Low, Medium, High”. This

assistance will be terminated at the end of pedaling or at braking. Additional power with or without

pedaling can be sent to the motor with a twist of the throttle. If you desire no battery assistance, turn the

control off.

On/Off

Battery Level

Mode: Level of desired power

10

www.BofeiliUSA.com © e-Bikes USA 2012

Motor

Because your Bofeili e-Bike utilizes a patented mid-bike (at the crankshaft), the motor utilizes the gear

system on your e-Bike. The Bofeili INTELEGENT CRANK-SHAFT MOTOR is the best configuration

for e-Bike riding rather than add-on kits or manufactured bikes that have hub motors in the front or rear

wheel which cannot utilize the gear system for speed or for

torque to ride up slopes. The motor is designed to provide

years of enjoyable biking without necessary service. The

brushless motor can be serviced, if ever necessary, by

qualified electric motor repairmen. DO NOT SUBJECT

THE MOTOR TO EXCESS WATER OR POOLS OF

STANDING WATER; this may cause electrical failure and

motor damage voiding all warranty.

Controller

The Controller is the electrical controls

which signal the battery, motor and pedals

to work in concert. Service of the

Controller should ONLY be done by an

experienced motor electrician. For

diagram information; the service tech may

contact the dealer.

11

www.BofeiliUSA.com © e-Bikes USA 2012

Shifting Gears – Shimano Derailleur

Your e-Bike is equipped with a 7-speed (or 21-speed on Sport model) Shimano derailleur. Adjusting

from one speed to another should only be done while the chain is in motion. Importance of timing when

using power takes a little getting used to but selecting the right gear for your given terrain is important.

Which gear to be in?

The numerically lowest number (1) is for the steepest hill while the largest (from 6-21) is for the most

speed. On the rear gear, (1) will have the chain on the largest sprocket while for speed, it will be on the

smallest sprocket.

Wheels, Tires & Tubes

Shimmy or wobble – see a bike shop to true the wheel. Check to make sure the wheel is

properly set in the forks and the cam is tight enough to keep the wheel running true.

Check tire pressure

Tire pressure should not exceed the PSI on the tire. For safe use, fill to the lowest recommended level

and allow the rubber to stretch for a period of time BEFORE inflating further. This precaution should

avoid pre-mature ruptures. For extended rides, a small hand pump and repair kit may be important to

carry. For a more comfortable ride, Bofeili e-Bikes use inner tubes. Tire replacements or extra tubes can

be purchased at e-Bikes USA or other bike part dealers.

Carry an extra tube on that extended ride

12

www.BofeiliUSA.com © e-Bikes USA 2012

Battery –Panasonic Cell Lithium 4 Ion

Warnings

DO NOT SUBJECT THE BATTERY TO EXCESS WET, HOT, SUN, COLD

OR PHYSICAL ABUSE WHICH WILL CAUSE BATTERY FAILURE OR

SHORTENED BATTERY LIFE. DO NOT DROP OR DAMAGE THE BATTERY

WHICH COULD CAUSE FIRE, EXPLOSION, AND/OR PERSONAL INJURY!

The above photo shows one type of battery and it’s gauge which shows 100%, 80%, 50%, & 20%.

Your e-Bike comes with two keys which are used to lock the e-Bike battery in place. Unlocking allows

the battery to be removed and charged inside if the e-Bike is away from an electrical connection. Sports

models have a pin-connection that must be removed from its “cylinder” style battery. The battery can be

charged while on the e-Bike by lifting the black flap on the back or side and inserting the low voltage

charger connection.

13

Storage

If battery is to be stored for an extended period of one month without use, it should be monitored as to

the level of charge and NEVER allow the battery to drop below 20% (or one red light showing) before

recharging. At a minimum, stored Lithium Ion batteries should be recharged at least every three months.

Charging

Charge your battery the first few times by draining (using) the majority of power then charging for at least

12 hours. This will most effectively” break in” the battery and give you the best and longest life possible.

After the first few times, the best practice is to charge the battery with the provided charger for your e-

Bike when the gauges indicates 20% remaining on the battery or one red light remaining. A normal

charge will take 4-8 hours until the green light on the charger is lit. The charger is equipped with 110-240

volt abilities and can be plugged into most all normal household receptacles.

14

Folding

The Folding Touring e-Bike is one of the lightest in its class at

44 lbs. The Folding Touring e-Bike has folding handlebar and

folding mid-frame that allows the bike to be compacted to the

side of a suitcase for easy transport or storage. A three-step

procedure takes only a few seconds to put the handlebar down.

When put back to its riding position it has a latch and

secondary lock that keeps the handlebars in place.

The mid-section fold has a

patented design to maintain a

ridged frame when riding yet a

sturdy hinge mechanism with

heavy latch.

Once the silver outer latch is

pulled back the bolt will be

freed, allowing the e-bike bike

to hinge upon itself. A

bungee-cord or tie will keep the tires together while

loading or hauling.

When returning to riding position, make sure the

bolt of the mid-section is securely locked in place

before the outer cover lock is latched in place. The

seat post is equipped with a quick-release cam if

you desire to lower or remove the seat.

15

Maintenance

Keep your bike and parts free from grit and excess soil build-up. Wipe parts and frame with a dry or

damp cloth. DO NOT RINSE THE e-BIKE WITH WATER. Keep joints and moving parts lightly

oiled as needed.

Perspective

Nothing lasts forever – the more you use it, the harder you use it, and the worse conditions you use it –

the shorter the life

If you find a crack – replace the part ASAP

Corrosion speeds damage – keep your bike and its parts clean and free from salt, grit and

other damaging abrasive/corrosive materials.

Color fades – When not in use, your e-Bike color will remain longer with care like an

auto; wash, wax, and store indoors.

Dents, scratches, excessive weight or use will promote cracks which will grow quickly.

Things that shorten the “life” of your e-bike

 Excess weight

 Rough terrain

 Crashes or physical abuse

 Strong aggressive riders

 Harsh riding style

 Corrosive/abrasive environment (wet, salt, water, sweat, sand, mud, grit)

 Improper storage

 Battery abuse (physical, charging improperly, storage)

Bolts, Nuts, Screws, & Cams

Check all bolts and screws and tighten as necessary. Check wheel cams and cams that adjust the seat and

handlebars. Improper tightness may cause an accident. For extended rides, certain tools may be helpful

to carry. Inspect the e-Bike prior to riding each time.

16

LIMITED WARRANTY

e-Bikes USA warrants for the original owner only the frame, motor, fork, or original component parts of

the Bofeili brand e-Bike to be free from defects in material and workmanship for the period of 1 year.

The warranty applies only to e-Bikes purchased from and assembled by e-Bikes USA. Components

(including the Panasonic cell Lithium Battery) not manufactured by Suzhou Bofeili Electric Technology

Co Ltd shall be covered exclusively by the stated warranty of their original manufacturer.

LIMITED REMEDY

Unless otherwise provided, the sole remedy under the warranty, or any implied warranty, is limited to the

replacement of defective parts with those of equal or greater value at the sole discretion of e-Bikes USA.

This warranty extends from the date of purchase, applies only to the original owner, and is not

transferable. In no event shall e-Bikes USA be responsible for any direct, incidental or consequential

damages, including, without limitation, damages for personal injury, property damage, or economic losses,

whether based on contract, warranty, negligence, product liability, or any other theory.

EXCLUSIONS

The above warranty, or any implied warranty, does not cover:

o Normal wear and tear on parts such as tires, chains, brakes, motor, cables and gearwheels

in situations where there are no assembly or material defects.

o Bicycles serviced by other than a qualified bicycle service center.

o Modifications from the original condition.

o Use of the bicycle for abnormal, competitive and/or commercial activities or for the

purposes other than those for which the e-bike was designed.

o Damage caused by failing to follow the e-Bike USA web site information

o Paint finish and decal damage resulting from taking apart in competitions, jumping,

downhill and/or training for such activities or events or as a result of exposing the bike to,

or riding the bike in, severe conditions or climates.

o Labor and shipping charges for part replacement or changeover.

If you have any questions, please contact us.

e-Bikes USA

www.e-BikesUSA.com

541.924.1837

E-Bike Bofeili Owner's manual

E-Bike Bofeili Owner's manual

Other documents