ducduc VERONA Assembly Instruction Manual

Category
Baby furniture
Type
Assembly Instruction Manual
Thank you for selecting a ducduc for nod product.
Keep instructions for future use.
Please check contents against the components list in
these instructions. Also, please ensure there was no
damage that may have occurred in shipping. if any
components are missing or you find any damage,
please contact The Land of Nod at 800-933-9904
before continuing.
Read all the instructions before use of the CRIB.
Please remember to securely tighten all bolts and
fasteners and periodically check to make sure every
component is properly and securely in place.
Pay close attention to the safety warnings in these
instructions and on CRIB labels.
A minimum of two people is required to safely
assemble and move the CRIB. Do not attempt to
move this CRIB alone - dragging or sliding it across
the floor may cause structural damage.
VERONA CRIB
CAUTION:
Any mattress
used in this CRIB must be
at least 27 1/4 inches by 51
5/8 inches with a thickness
not exceeding 6 inches.
1
2
G
K.2
L.2
F
Attach CRIB LEG to SIDE PANEL with one RAIL CONNECTOR BOLT ,
LOCKING WASHER , and REGULAR WASHER . Tighten with ALLEN WRENCH . .
REPEAT FOR ACCENT PANEL .
Lay SIDE PANEL down with holes facing up.
While SIDE PANEL is laying down, attach BASE with two BASE CONNECTOR BOLTS ,
LOCKING WASHERS and REGULAR WASHERS . Tighten with ALLEN WRENCH .
Flip to standing position and attach ACCENT PANEL in same fashion.
Align the BASE so that the sticker “Bottom” is facing the floor. The side of BASE with only
two corner holes should be aligned against SIDE PANEL as shown.
I I
J
G
K.2
L.2
J
3
accent panel
connector holes
A.2
K.2
Back
I
Place SIDE RAIL onto BASE with rail connector holes facing SIDE PANEL . Attach
ACCENT PANEL to crib SIDE RAIL and secure in place with two BASE CONNECTOR
BOLTS , LOCKING WASHERS , and REGULAR WASHERS as shown below. Tighten
all bolts with ALLEN WRENCH .
K.2
accent panel
connector holes
base connector holes
base connector holes
G
J
L.2
K.2
base connector holes
Back J
B
I
A.1
mattress support holes
A
Place END RAIL onto BASE with mattress support holes facing the bottom and inside of crib.
Secure END PANEL to BASE with BASE CONNECTOR BOLTS , LOCKING
WASHERS , and REGULAR WASHERS from underneath as shown below.
Place other END RAIL on the opposite side with mattress support holes facing the bottom and
inside of crib. Secure END RAIL to BASE with BASE CONNECTOR BOLTS ,
LOCKING WASHERS , and REGULAR WASHERS from underneath as shown below.
Secure SIDE RAIL with BASE CONNECTOR BOLTS , LOCKING WASHERS , and
REGULAR WASHERS from underneath as shown below. Tighten all bolts with ALLEN WRENCH .
4
It may be easier to access the top frame connector holes by laying the frame on its side (place on
a blanket to prevent scraping). Also, only slightly tighten bolts until all of them are in place and
aligned. Tighten all bolts with ALLEN WRENCH .
5
1
2
F
K.2
L.2
rail connector holes
rail connector holes
F
K.2
L.2
L.2
Back
B
A.1
1
2
Back
B
rail connector holes
rail connector holes
A
6Line up the rail connector holes on SIDE RAIL with rail connector holes on END RAIL .
Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR BOLTS
and insert two RAIL CONNECTOR BOLTS in rail connector holes and slightly tighten with
ALLEN WRENCH . Repeat for END PANEL on opposite side.
Line up the rail connector holes on SIDE PANEL with the rail connector holes on the END RAILS .
Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR BOLTS and
insert and slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN WRENCH .
corner-holes
C
7
8
Back
The MATTRESS SUPPORT PANEL may be installed in one of four positions. See the four
different mattress support holes in each corner of the CRIB. First, select the desired mattress
height. Then, unscrew the MATTRESS SUPPORT PIN from each MATTRESS SUPPORT
BOLT . Insert the smooth ends of each MATTRESS SUPPORT PIN in the desired
mattress support holes on END RAILS . See drawing for proper pin orientation.
Carefully lower MATTRESS SUPPORT PANEL with labels facing up.
Align corner holes to sit on MATTRESS SUPPORT PINS .
Tighten bolts all the way.
D
E
C
C
C
9
K.1
L.1
Attach one LOCKING WASHER and one REGULAR WASHER on top of each
MATTRESS SUPPORT PIN . Secure and tighten each of the four MATTRESS SUPPORT
BOLTS to each of the four MATTRESS SUPPORT PINS
.
Use SCREWDRIVER to
tighten securely.
10 Press firmly in center of MATTRESS SUPPORT PANEL to ensure proper placement.
In the event MATTRESS SUPPORT PANEL does not appear to be secure remove and
repeat steps 7 to 9. The MATTRESS SUPPORT PANEL must be firmly attached at
all four corners.
The mattress height should be lowered as your baby grows to ensure that
he/she does not climb out of the CRIB. When child is able to pull to a
standing position, set mattress to lowest position and remove bumber pads,
large toys, and other objects that could serve as steps for climbing out.
Regularly asses your baby’s abilities and make adjustments accordingly.
To adjust the height of the mattress support, remove the mattress from the
crib. Unscrew all four MATTRESS SUPPORT BOLTS , remove all LOCKING
WASHERS , and REGULAR WASHERS and remove MATTRESS
SUPPORT PANEL . Remove and reinsert the smooth ends of each
MATTRESS SUPPORT PIN in mattress support holes on END RAILS
at desired height. Refer to steps 7 through 9 for reinserting MATTRESS
SUPPORT PANELS and reattaching REGULAR WASHERS , LOCKING
WASHERS , and MATTRESS SUPPORT BOLTS .
Periodically check to make sure every component is properly and securely
in place and all bolts and fasteners are tight.
Do not scratch or chip the finish. Do not use abrasive chemicals for
cleaning. Clean with mild oap on a soft rag. Rinse and dry throughoughly.
If you ever refinish this furniture, be sure to use only a non-toxic finish
specified for childrens furniture.
Store crib in a dry area.
operation
ducduc llc 524 broadway no. 206 ny ny 10012 t 212.226.1868 f 212.226.5504 www.ducducnyc.com
Failure to follow these warnings and the assembly instructions could result in serious
injury or death.
Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
Infants can suocate on soft bedding. Never add a pillow or comforter. Never place
additional padding under infant.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs
to sleep, unless otherwise advised by your physician.
Strings can cause strangulation! Do not place items with a string around a child’s neck, such as
hood strings or pacier er cords. Do not suspend strings over a crib or attach strings to toys.
To help prevent strangulation tighten all fasteners. A child can trap parts of the body or
clothing on loose fasteners.
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
When child is able to pull to a standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
Stop using crib when child begins to climb out or reaches the height of 35 in. (89 cm.).
Check this product for damaged hardware, loose joints, loose bolts or other fasteners,
missing parts, or sharp edges before and after assembly and frequently during use.
Securely tighten loose bolts and other fasteners. DO NOT use crib if any parts are
missing, damaged or broken. Contact ducduc for replacement parts and instructional
literature if needed. DO NOT substitute parts.
If renishing, use a non-toxic nish specied for children’s products.
Follow warnings on all products in a crib.
Never use plastic shipping bags or other plastic lm as mattress covers because they can
cause suocation.
Infants can suocate in gaps between crib sides and a mattress that is too small.
Strangulation Hazard:
Fall Hazard:
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

ducduc VERONA Assembly Instruction Manual

Category
Baby furniture
Type
Assembly Instruction Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI