KennelMaster K6510CLBL/C User manual

Brand: KennelMaster

Model: K6510CLBL/C

Type: User manual

f.'|,@,:

fi,,r,-;r-tr-i..r..::r/.?.,'.;

tt

+,

::,'

.

r-*'"F[cni6hiiCmbly

Start by assembling the lower

frame

by

pushing

swagged

pieces

together.

See

Fig.

1

for

arrangement.

Keep the

tubes

that accept the

vertical tubes

(C)

all

pointed

up in the same direction.

Build

the upper

frame

at this

point

and set

it aside Fig.2.

Plan

gate placement.

Hinge

post

(B)

location

will deter-

mine

the

gate placement.

Position

hinge

in

door

open-

ing

and hooks

should

point

aboirt

45 degrees

outward.

This

will

allow

the fabric to attach ts the

outside

of the

frame.

NotqThe

gate

is

designed

to

be installed

on the

left

side

oJa corner

position.

:

lnsert all 5

vertical

tubes

(C)

into

the

lower

frame

Fig.3

&4. You may need

to tap

the

verticaltubes

(C)

into

the

lower

frame.

Do

not hammer directly on

the tube,

use a

block of wood to

protect

the tube.

With allverticaltubes

(C)

and hinge

post

(B)

in

place,

pick

up the assembled upper frame and

place

it

on the

vertical

tubes

(C).

Fig.

5

This

step will require 2

people

Gate lnstall

The

gate

comes

completely

assembled

with

hinges

pre-attached

Fig.6.

Simply drop the

gate(A)

hinge

pins

down in

to

the

hinge tube

on the

hinge

post

(B).

Push

d

cotter

pin

(E)

into

each of the hinges and bend

back

with

pliers

around the hinge

pin.

Latch

is already

pre-

assembled on the

latch

post

(A).

Notc: Latch can be

opened from

the inside

the

kennel as

well.

Next, installthe latch

post

(A).

Latch

post

must

be

placed

on the

left

side of the hinge

post

(B)

and

to the

tatch

side

of the

gate.

This

post

clamps to the

upper and

lower frame

and can be

slid

to

adjust

the

gate

opening.

Fio. T

@/N

'x->

b-,-

Assemble

the

corrugated

jacks

(K)

to

put

under

the

frame to

lift

it

off

the

ground.

Slide two

pieces

of

the

corrugated

board

together as

shown

in

Fig.

7.

Lift

the

kennel

frame

and

put

the

jack

under

the side

of

the

kenne[

where

installing the

latch

post(A).

This

will

make

it

easier

to clamp

the

latch

post

(A)

on

the

lower

frame.

Set

latch Post at

preferred

location

for

easy

latch

operation

and then

tighten

the

nut

on the

top

and

bottom

of

the

clamps

to

secure.

Fig.8

Note:

Loosen

clamps

of

latch

post

(Al

to adjust

for

precise

latch closure.

Using

a

screw

gun

with

a Phillips

bit,

put

a

self-

tapping

screw

through

pilot

holes

in

tubes

and

into

all vertical posts

attaching

to

the

upper

and

lower

frames.

Fig.9

Chain

Link Fabric

Lay

fabric

down.

Remove

wires

that

hold

the

roll

together.

Lift roll

carefully

and hook

the

chain

link

fabric

onto

the

hinge

post

(B)

tension

strip.

Unroll

the

fabric

around

the

kennelframe.

This

willtake

two

people

to

assure

the fabric

stays

held

to

the

frame

and

tensioned

as

it is

unrolled

and

pulled

around

the

kennelframe.

Fig.

l0

When

you

have

the

fabric

unrolled'and

have

made

it

arouRd

the

kennel

frame

to the

latch

post

(A)

hook

the fabric

onto

the

tension

strip.

Fig.

I

l lf

the fabric

is

too long

and

has

too

much slack,

you

must,tut,,the

roll.

Do this

by

removing

a wire

at

desired

length.

Unhook

the

wire

to

be

removed

at

the

top

and

bottom

with

a

pliers.

Remove

the

wire

by

twisting

the

wire

out

of

the top.

Fig.

I2

Note:

For

hest

fit

to

the

hooks,

it

may

be

necessary

to remoye

two

wires

so

that

the

mesh

are

full

dia-

monds

from

top

to

bottom.

Tension

strip

hooks

can

be

bent

down

to.secure

the

chain

link

fabric

once

final

tension

has

been

achieved.

1
2
3

KennelMaster K6510CLBL/C User manual

Brand: KennelMaster

Model: K6510CLBL/C

Type: User manual

Download PDF

Related papers

Other documents