Honeywell HCM 800 - PermaFresh Cool Moisture Humidifier User manual

IMPORTANT SAFETY

INSTRUCTIONS

READ AND SAVE THESE SAFETY

INSTRUCTIONS BEFORE USING THIS

HUMIDIFIER

When using electrical appliances, basic precautions

should always be followed to reduce the risk of re,

electric shock, and injury to persons, including the

following:

1. Always place this humidier on a rm, at and level

surface. This humidier may not work properly on an

uneven surface.

2. Place this humidier in an area where it is not accessible

to children.

3. Do not place the humidier near any heat sources such as

stoves, radiators, and heaters.

4. Do not use the humidier outdoors.

5. Before using the humidier, check the power cord for any

signs of damage. If the cord is found to be damaged, DO

NOT USE and return the humidier to the manufacturer

under the warranty agreement for repair.

6. This appliance has a polarized plug (one blade is wider

than the other). To reduce the risk of shock, this plug is

intended to t only one way in a polarized outlet. If the

plug does not t securely in the outlet, reverse the plug. If

it still does not t, contact a qualied electrician. DO NOT

attempt to defeat this safety feature.

7. To disconnect the humidier, rst turn controls to the

OFF position, then grip the plug and pull it from the wall

outlet. Never pull by the cord.

8. A loose t between the AC outlet (receptacle) and plug

may cause overheating and a distortion of the plug.

Contact a qualied electrician to replace loose or worn

outlet.

9. The humidier should always be unplugged and emptied

when not in operation or while being serviced or cleaned.

10. Never tilt or attempt to move the humidier while it is

operating or lled with water. UNPLUG the humidier

before moving.

11. This humidier requires regular cleaning. Refer to

the CLEANING instructions provided. Never clean the

humidier in any manner other than as instructed in this

manual.

12. Do not direct moisture ow directly at individuals, walls

or furniture.

13. When a humidier is used in a closed room or small

rooms, check periodically for proper ventilation, as

excessive humidity can cause condensation stains on

walls.

14. Turn the humidier OFF if you notice moisture on the

inside of your windows. For proper humidity reading

use a hygrometer, which is available in many hardware

and department stores, or by ordering one from the

manufacturer.

Cool Moisture HuMidifier witH

w

asHable filter

HCM-800 Series

The Honeywell trademark is used by Kaz, Inc. under license from Honeywell Intellectual Properties, Inc.

HCM-800_OM.indd 1 4/5/07 12:06:37 PM

2

SETTING UP YOUR HUMIDIFIER

Your humidier is made up of these parts:

It is recommended that you disinfect your humidier prior to rst use. See CLEANING Instructions.

*Protec

TM

cartridge sold separately.

Motor Housing

Permanent

Washable Filter

and

Filter Holder-1 pc

Water Tank

Base

Tank Cap

Gasket

Screen

(Located

under Motor

Housing)

Filter properly

located on base

Protec

TM

Cleaning

Cartridge

Holder*

HCM-800_OM.indd 2 4/5/07 12:06:38 PM

3

SETTING UP YOUR HUMIDIFIER (CONT’D)

Select a rm, level location at least 6” (15cm) from any walls

for proper airow. Place the humidier on a water-resistant

surface, as water can damage furniture and some ooring.

Kaz will not accept responsibility for property damage caused

by water spillage.

Placement

Fill Tank

Power

Step 1

Remove the water tank Turn tank upside-down.

Remove tank cap by turning

counter- clockwise

.

Step 2

Step 3

Step 4

Fill tank with cool tap water.

Replace tank cap. Tighten by

turning clockwise

.

Place tank back on humidier.

Once the lled water tank has

been placed on the unit do not

move humidier. Doing so could

cause leakage and spills.

With the power switch in the OFF position, plug the

lled humidier into a polarized 120V outlet. DO NOT

FORCE THE POLARIZED PLUG INTO THE OUTLET; it will

only t one way.

DO NOT plug in humidier with wet hands to

avoid electric shock.

Step 1

Water Tank

HCM-800_OM.indd 3 4/5/07 12:06:41 PM

4

OPERATING YOUR HUMIDIFIER

Output/Fan

Speed Control

Set Humidity

Step 1

Set fan speed to desired output:

High ( ) Fast Humidifying

Medium ( ) Everyday moisture control

Low ( ) Nighttime or maintenance use

Step 1

Turn the humidistat knob

clockwise

to the highest

setting (

).

Run on high for at least 1 hour

or until room has reached a

comfortable humidity level.

Step 2

Then, slowly turn the humidistat knob counter-

clockwise

until the humidier shuts o.

The illuminated water window will change from

blue to green when the desired humidity level

is reached.

Once set, the humidier will automatically cycle

on and o based on your setting.

NOTE: To ensure proper humidity in your home, you should

use a hygrometer (room humidity indictor) such as the E-10

and place across the room from your humidier.

(Hygrometer sold separately)

Properly

Maintaining

Room

Humidity

HCM-800_OM.indd 4 4/5/07 12:06:43 PM

5

NOTE: It is recommended that all maintenance be done in the kitchen or bathroom on a water resistant surface.

Remove water tank from unit before moving.

The lter should be cleaned every 1-3 months depending on your water quality. Keep in mind, depending on your water quality,

mineral deposits can still clog or discolor the lter, aecting the performance of your humidier.

It is recommended you clean your lter in the bathroom or kitchen. Keep in mind your lter may be damp depending on your

last usage.

Note: Filter is contained in a lter holding frame. Please do not remove lter from frame or it may be damaged.

Do not discard your lter or frame.

Step 1 Step 2 Step 3 Step 4

Step 5 Step 6 Step 7

Turn o and unplug your

humidier.

Remove the water tank and

motor housing and carefully

set aside.

Remove lter holding frame

and lter from the unit.

Soak lter in 2 tsp vinegar

per gallon of water.

Let stand for 20 minutes. Insert lter frame back into

the base of the humidier.

Note: Do Not Wring or

Squeeze Filter.

Replace motor housing and

water tank.

CLEANING YOUR FILTER

HCM-800_OM.indd 5 4/5/07 12:06:44 PM

6

Step 1 Step 2

1

g

a

l

Step 3

DISINFECTING

Remove the motor housing and lter and carefully set aside.

Failure to do so will damage the lter.

Fill water tank with 1 tsp. of

household bleach and 1 gallon

of cool water.

Let stand for 20 minutes With vinegar in the tank and

base, wipe surface with a soft

cloth or brush.

Step 6 Step 7Step 5 Step 8

Rinse the base and water

tank thoroughly with water

to remove scale and cleaning

solution.

Fill base with clean, cool tap

water. Replace motor housing

back on base and let sit 20

minutes.

With a soft cloth, clean the

screen located under the main

housing to remove mineral

deposits.

NOTE: REMOVE FILTER BEFORE CLEANING.

Failure to remove lter during cleaning will destroy the lter.

Step 1 Step 2 Step 3 Step 4

Turn o and unplug your

humidier.

Remove the water tank and

housing and carefully set the

motor housing aside.

Place base and water tank

in sink or tub and ll with

undiluted vinegar.

Place motor housing on base

and let sit.

NOTE: Do not turn on.

SCALE REMOVAL

Cleaning involves two steps, SCALE REMOVAL and DISINFECTING. Be sure to perform these in the proper order to

avoid harmful chemical interactions.

CLEANING

HCM-800_OM.indd 6 4/5/07 12:06:46 PM

7

Pour some solution into

the base.

Step 4

NOTE: The use of other water treatment products

and chemicals may cause deterioration of the lter

or damage the humidier, thereby hindering the

humidier’s eectiveness.

END-OF-SEASON CARE AND STORAGE

• Follow the CLEANING instructions when the humidier will not be used for at least one week or more,

or at the end of the season.

• At the end of the season, remove and throw away the lter; do not store with a used lter.

• Dry the humidier completely before storing. DO NOT store with water inside the Base or Water Tank.

• Pack the unit in its original carton and store in a cool, dry location.

• Before next use, remember to clean your humidier and install a new lter.

CONSUMER RELATIONS

Mail questions or comments to: Kaz, Incorporated

Consumer Relations Dept.

250 Turnpike Road, Southborough, MA 01772

Please be sure to specify model number.

Call us toll-free at: 1-800-477-0457; E-mail: consumerr[email protected]

Or visit our website at: www.kaz.com

NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CONSUMER RELATIONS FIRST OR SEE YOUR WARRANTY. DO

NOT RETURN THE HUMIDIFIER TO THE ORIGINAL PLACE OF PURCHASE. DO NOT ATTEMPT TO OPEN THE MOTOR HOUSING

YOURSELF, DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE TO THE PRODUCT OR PERSONAL INJURY.

ELECTRICAL RATINGS

The Honeywell QuietCare™ Series models are rated at 120V, 60 Hz.

Step 5

Let stand for 20 minutes. Rinse

with water until the smell of

bleach is gone.

CLEANING (CONT’D)

HCM-800_OM.indd 7 4/5/07 12:06:46 PM

8

TROUBLESHOOTING

Q: I hear the fan turning, but I don’t see any mist. Is my humidier operating properly?

A: Dry air is pulled through the system and a fan disperses invisible, moisture balanced air. There is no “mist” emitted. When

operating normally you will feel only cool air coming from the unit. Monitor the water level in your Tank/ Base. If you notice

a decrease in the Water Tank over 24 hours then the unit is operating normally.

Q: My unit has been running for several hours. I hear the fan spinning, but I do not notice the water level in the

tank decreasing.

A: Check the water window to see if water is owing through the system. If the water window does not show any water owing,

then remove the housing and check the silver screen located on the bottom of the pump to ensure the screen is not blocked.

Also please note, if the humidity level in your home is above 60%, you air is fully saturated and the humidier will be unable

to put out additional moisture.

Q: The humidier is not running (the fan is not even spinning), but all (or some) of the lights are on.

A: The water window will change from blue to green when your desired humidity is reached. The unit will then shut o until the

room humidity drops below the preset level or you change the control to a higher humidity setting.

Q: The Advanced Mist™ Humidistat knob was set according to the manual, but the humidier never seems to turn

back on. Is something wrong?

A: The Humidistat knob may be set too low. Moving the Humidistat knob to the end clockwise should restart the unit.

Q: The Advanced Mist™ Humidistat knob was set according to the manual, but the humidier never seems to turn

o. Is something wrong?

A: The Humidistat knob may be set too high. Reset the Advanced Mist™ Humidistat knob following the instructions under

FEATURES.

Q: My lter has turned light brown and rust colored or has a lot of scaling. Do I need to clean my lter?

A: Probably not. Since your lter has been made with Protec™ antimicrobial the change in color indicates only a mineral

deposit. Soak lter in a sink full of cool water to help break up deposits. The discoloration may remain but will not aect

the humidier’s performance. Your lter should however be cleaned every 1-3 months depending on usage to keep your

humidier operating properly

Q: My humidier doesn’t appear to be as clean as when I rst purchased and/or I’m smelling an unpleasant odor.

What should I do?

A: If you have been using your humidier regularly for over 30 days, follow the cleaning instructions.

Q: Unit is running but I do not see any visible water movement in my water window.

A: Check to be sure your unit is not out of water. Also check to make sure the pump inlet screen is not clogged.

Q: My unit makes a gurgling sound.

A: When the unit rst starts up, there may be air that is sucked into the system which can produce this sound. Please allow 15 to

30 minutes for this to go away.

HCM-800_OM.indd 8 4/5/07 12:06:46 PM

9

You should rst read all instructions before attempting

to use this product.

A. This 3 year limited warranty applies to repair or

replacement of product found to be defective in material

or workmanship. This warranty does not apply to damage

resulting from commercial, abusive, unreasonable use

or supplemental damage. It also does not apply to the

lter or Protec™ Cleaning Cartridge. Defects that are the

result of normal wear and tear will not be considered

manufacturing defects under this warranty.

KAZ IS NOT LIABLE FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES OF ANY NATURE. ANY

IMPLIED WARRANTY OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE ON THIS

PRODUCT IS LIMITED IN DURATION TO THE DURATION

OF THIS WARRANTY.

Some jurisdictions do not allow the exclusion or limitation

of incidental or consequential damages or limitations

on how long an implied warranty lasts, so the above

limitations or exclusions may not apply to you. This

warranty gives you specic legal rights, and you also

may have other rights which vary from jurisdiction to

jurisdiction. This warranty applies only to the original

purchaser of this product from the original date of

purchase.

B. At its option, Kaz will repair or replace this product if it is

found to be defective in material or workmanship.

C. This warranty does not cover damage resulting from any

unauthorized attempts to repair or from any use not in

accordance with the instruction manual.

D. Return defective product to Kaz, Incorporated with a brief

description of the problem. Include proof of purchase and

a $10 US/$15.50 CAN check or money order for handling,

return packing and shipping charges. Please include your

name, address and a daytime phone number.

You must prepay shipping charges. We suggest

having tracking or delivery conrmation. Send to:

In U.S.A.:

Kaz, Incorporated

Attn: Returns Department

4755 Southpoint Drive

Memphis, TN 38118

USA

In Canada:

Kaz Canada, Inc.

Attn: Returns Department

510 Bronte Street South

Milton, ON L9T 2X6

Canada

3 YEAR LIMITED WARRANTY

P/N: 31IMM800190

HCM-800_OM.indd 9 4/5/07 12:06:46 PM

HCM-800_OM.indd 10 4/5/07 12:06:46 PM

Page is loading ...

20

HCM-800_OM.indd 20 4/5/07 12:06:51 PM

Page is loading ...

Honeywell HCM 800 - PermaFresh Cool Moisture Humidifier User manual

This manual is also suitable for

Honeywell HCM 800 - PermaFresh Cool Moisture Humidifier User manual

in other languages

Related papers

Other documents