Dell EMC PowerSwitch N3100 Series Owner's manual

Dell Networking

N2128PX-ON/N3132PX-ON

Switches

Getting Started Guide

Guide de mise en route

Guia de Noções Básicas

Guía de introducción

Regulatory Model: N2128PX-ON/

N3132PX-ON

Regulatory Type: E05W003/E06W003

Page is loading ...

Dell Networking

N2128PX-ON/N3132PX-ON

Switches

Getting Started Guide

Regulatory Models: N2128PX-ON/

N3132PX-ON

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your switch.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of

data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal

injury, or death.

____________________

copyright and intellectual property laws.

Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other jurisdictions.

All other marks and names mentioned herein may be trademarks of their respective companies.

Regulatory Models N2128PX-ON/N3132PX-ON

April 2016 P/N 1VT9M Rev. A00

Contents 3

Contents

1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . 7

N2128PX-ON Hardware Overview. . . . . . . . . . . . . 7

Power Consumption for N2128PX-ON

PoE Switches

. . . . . . . . . . . . . . . . . . . . . 7

N2128PX-ON Model Summary

. . . . . . . . . . . . . . . 8

2 N2128PX-ON Installation . . . . . . . . . . . . . . 9

Rack Mounting an N2128PX-ON Switch . . . . . . . . . 9

Installing in a Rack

. . . . . . . . . . . . . . . . . . 9

Installing as a Free-standing Switch . . . . . . . . 10

Stacking Multiple N2128PX-ON Switches . . . . . . . 10

3 Starting and Configuring the

N2128PX-ON Switch . . . . . . . . . . . . . . . . 11

Connecting an N2128PX-ON Switch to a Terminal . . . 12

Connecting an N2128PX-ON Switch to a

Power Source

. . . . . . . . . . . . . . . . . . . . . . 13

AC and DC Power Connection

. . . . . . . . . . . 13

Booting the N2128PX-ON Switch

. . . . . . . . . . . . 14

4 Contents

Performing the N2128PX-ON Initial Configuration . . . 15

Enabling Remote Management

. . . . . . . . . . . 15

Initial Configuration Procedure

. . . . . . . . . . . 16

Example Session . . . . . . . . . . . . . . . . . . 17

Dell Easy Setup Wizard Console Example

. . . . . 18

Next Steps

. . . . . . . . . . . . . . . . . . . . . 22

4 N3132PX-ON Hardware Overview . . . . . 24

Power Consumption for N3132PX-ON PoE Switches . . . 24

Ventilation System

. . . . . . . . . . . . . . . . . 26

N3132PX-ON Model Summary

. . . . . . . . . . . . . . 27

5 N3132PX-ON Installation . . . . . . . . . . . . 28

Rack Mounting a N3132PX-ON Switch . . . . . . . . . 28

Rack Mounting Safety Considerations

. . . . . . . 28

Installing the Dell ReadyRail System . . . . . . . . 29

Installing as a Free-standing Switch

. . . . . . . . 33

Stacking Multiple N3132PX-ON Switches

. . . . . . . 33

6 Starting and Configuring the

N3132PX-ON Switch . . . . . . . . . . . . . . . . 34

Connecting an N3132PX-ON Switch to a Terminal . . . 35

Connecting an N3132PX-ON Switch to a

Power Source

. . . . . . . . . . . . . . . . . . . . . . 36

AC and DC Power Connection

. . . . . . . . . . . 37

Booting the N3132PX-ON Switch . . . . . . . . . . . . 37

Contents 5

Performing the N3132PX-ON Initial Configuration . . . 38

Enabling Remote Management

. . . . . . . . . . . 38

Initial Configuration Procedure

. . . . . . . . . . . 39

Example Session . . . . . . . . . . . . . . . . . . 40

Dell Easy Setup Wizard Console Example

. . . . . 41

Next Steps

. . . . . . . . . . . . . . . . . . . . . 45

7 NOM Information (Mexico Only) . . . . . . . 47

Page is loading ...

Getting Started Guide 7

Introduction

This document provides basic information about the Dell

®

Networking

N2128PX-ON/N3132PX-ON switches, including how to install a switch and

perform the initial configuration. For information about how to configure and

monitor switch features, refer to the User Configuration Guide, which is

available on the Dell Support website at dell.com/support, for the latest

updates on documentation and firmware.

NOTE: Switch administrators are strongly advised to maintain Dell Networking

switches on the latest version of the Dell Networking Operating System (DNOS).

Dell Networking continually improves the features and functions of DNOS based on

feedback from you, the customer. For critical infrastructure, pre-staging of the new

release into a non-critical portion of the network is recommended to verify network

configuration and operation with the new DNOS version.

N2128PX-ON Hardware Overview

This section contains information about device characteristics and modular

hardware configurations for the Dell Networking N2128PX-ON switch.

Power Consumption for N2128PX-ON PoE Switches

Table 1-1 describes the power consumption for N2128PX-ON PoE switches.

The system power consumption is 90 watt (W). The PoE power budget is

800W for the main power supply (PSU).

Table 1-1. Power Consumption for N2128PX-ON PoE Switches

Table 1-2 shows power consumption data for the PoE-enabled N2128PX-ON

switches operating from the Modular Power Supply (MPS) only. The PoE

power budget is 800W for MPS.

Model Input Voltage Power Supply

Configuration

Maximum Steady

Current

Consumption (A)

Maximum

Steady

Power (W)

N2128PX-ON 100V/60Hz Main PSU 9.73A 965.5W

110V/60Hz Main PSU 8.75A 960.4W

120V/60Hz Main PSU 8.03A 958.3W

220V/50Hz Main PSU 4.33A 931W

240V/50Hz Main PSU 3.97A 928.7W

8 Getting Started Guide

Table 1-2. Power Consumption Data for N2128PX-ON Switches PoE (+ MPS)

Table 1-3 shows power consumption data for the PoE-enabled N2128PX-ON

switches. The PoE power budget is 1600W for the main power supply +

Modular Power Supply (MPS).

Table 1-3. Power Consumption for N2128PX-ON PoE Switches

N2128PX-ON Model Summary

Table 1-4. N2128PX-ON Switch Regulatory Numbers

Model Input

Voltage

Power Supply

Configuration

Maximum Steady

Current Consumption

(A)

Maximum

Steady

Power (W)

N2128PX-

ON

100V/60Hz MPS 9.92A 986.5W

110V/60Hz MPS 8.93A 975.7W

120V/60Hz MPS 8.01A 955.4W

220V/50Hz MPS 4.44A 945.4W

240V/50Hz MPS 4.08A 951.4W

Model Input Voltage Power Supply

Configuration

Maximum Steady

Current

Consumption (A)

Maximum

Steady

Power (W)

N2128PX-ON 100V/60Hz Main PSU + MPS 11.83A 1175W

110V/60Hz Main PSU + MPS 10.71A 1169W

120V/60Hz Main PSU + MPS 9.84A 1168.9W

220V/50Hz Main PSU + MPS 5.4A 1138.4W

240V/50Hz Main PSU + MPS 5.93A 1141W

Marketing

Model

Name

(MMN)

Description Power Supply

Unit (PSU)

Regulatory

Model

Number

(RMN)

Regulatory

Type

Number

(RTN)

N2128PX-

ON

24x1G/4x2.5G/2x10G

SFP+/2xStacking/24x

PoE+/4xPoE 60W Ports

1000W E05W E05W003

Getting Started Guide 9

N2128PX-ON Installation

Rack Mounting an N2128PX-ON Switch

WARNING: Read the safety information in the

Safety and Regulatory Information

as well as the safety information for other switches that connect to or support the

switch.

The AC power connector is on the rear panel of the switch.

Installing in a Rack

WARNING: Do not use rack mounting kits to suspend the switch from under a

table or desk, or attach it to a wall.

CAUTION: Disconnect all cables from the switch before continuing. Remove all

self-adhesive pads from the underside of the switch, if they have been attached.

CAUTION: When mounting multiple switches into a rack, mount the switches

from the bottom up.

1

Place the supplied rack-mounting bracket on one side of the switch,

ensuring that the mounting holes on the switch line up to the mounting

holes in the rack-mounting bracket. Figure 1-1 illustrates where to mount

the brackets.

Figure 1-1. Attaching the Brackets

2

Insert the supplied bolts into the rack-mounting holes and tighten with a

screwdriver.

10 Getting Started Guide

3

Repeat the process for the rack-mounting bracket on the other side of the

switch.

4

Insert the switch into the 48.26 cm (19 inch) rack, ensuring that the rack-

mounting holes on the switch line up to the mounting holes in the rack.

5

Secure the switch to the rack with either the rack bolts or cage nuts and

cage-nut bolts with washers (depending on the kind of rack you have).

Fasten the bolts on bottom before fastening the bolts on top.

CAUTION: Make sure that the supplied rack bolts fit the pre-threaded holes in the

rack.

NOTE: Make sure that the ventilation holes are not obstructed.

Installing as a Free-standing Switch

NOTE: Dell strongly recommends mounting the switch in a rack.

Install the switch on a flat surface if you are not installing it in a rack. The

surface must be able to support the weight of the switch and the switch

cables. The switch is supplied with four self-adhesive rubber pads.

1

Attach the self-adhesive rubber pads on each location marked on the

bottom of the switch.

2

Set the switch on a flat surface, and make sure that it has proper

ventilation by leaving 5 cm (2 inches) on each side and 13 cm (5 inches) at

the back.

Stacking Multiple N2128PX-ON Switches

You can stack N2128PX-ON switches up to 12 switches high using the mini-

SAS ports located on the rear of the switch. When multiple switches are

connected together through the stack ports, they operate as a single unit with

up to 336 front panel ports. The stack operates and is managed as a single

entity. Refer to the User Configuration Guide and the CLI Reference Guide for

more information.

Getting Started Guide 11

Starting and Configuring the

N2128PX-ON Switch

The following flow chart provides an overview of the steps you use to perform

the initial configuration after the switch is unpacked and mounted.

Figure 1-2. Installation and Configuration Flow Chart

12 Getting Started Guide

Connecting an N2128PX-ON Switch to a Terminal

After completing all external connections, configure the switch by connecting

it to a terminal.

NOTE: Read the Release Notes for this product before proceeding. You can

download the Release Notes from the Dell Support website at dell.com/support.

NOTE: Dell recommends that you obtain the most recent version of the user

documentation from the Dell Support website at dell.com/support.

To monitor and configure the switch via serial console, use the console port

on the front panel of the switch to connect it to a VT100 terminal or to a

computer running VT100 terminal emulation software. The console port is

implemented as a data terminal equipment (DTE) connector.

The following equipment is required to use the console port:

• VT100-compatible terminal or a computer with a serial port running

VT100 terminal emulation software,

such as HyperTerminal

®

.

• A serial cable (provided) with an RJ-45 connector for the console port and

DB-9 connector for the terminal.

Perform the following tasks to connect a terminal to the switch console port:

1

Connect the DB-9 connector on the serial cable to the terminal or

computer running VT100 terminal emulation software.

2

Configure the terminal emulation software as follows:

a

Select the appropriate serial port (for example, COM 1) to connect to

the console.

b

Set the data rate to 115,200 baud.

c

Set the data format to 8 data bits, 1 stop bit, and no parity.

d

Set the flow control to none.

e

Set the terminal emulation mode to

VT100

.

f

Select Terminal keys for Function, Arrow, and Ctrl keys. Make sure

that the setting is for Terminal keys (not Microsoft Windows keys).

3

Connect the RJ-45 connector on the cable directly to the switch console

port. The Dell Networking console port is located on the right side of the

front panel and is labeled with a

|O|O|

symbol.

Getting Started Guide 13

NOTE: Serial console access to the stack manager is available from any

serial port via the local CLI. Only one serial console session at a time is

supported.

Connecting an N2128PX-ON Switch to a Power

Source

CAUTION: Read the safety information in the

Safety and Regulatory Information

manual as well as the safety information for other switches that connect to or

support the switch.

The N2128PX-ON model has one internal power supply. The

power receptacle

is on the rear panel.

AC and DC Power Connection

1

Make sure that the switch console port is connected to a VT100 terminal

or VT100 terminal emulator via the RJ-45 to DB-9 female cable.

2

Using a 5-foot (1.5 m) standard power cable with safety ground connected,

connect the power cable to the AC main receptacle located on the rear

panel.

3

Connect the power cable to a grounded AC outlet.

4

If you are using a redundant or external DC power supply, such as the Dell

Networking RPS720 or Dell Networking MPS1000 (N2128PX-ON only),

connect the DC power cable to the DC receptacle located on the rear

panel.

14 Getting Started Guide

Booting the N2128PX-ON Switch

When the power is turned on with the local terminal already connected, the

switch goes through a power-on self-test (POST). POST runs every time the

switch is initialized and checks hardware components to determine if the

switch is fully operational before completely booting. If POST detects a

critical problem, the program flow stops. If POST passes successfully, valid

firmware is loaded into RAM. POST messages are displayed on the terminal

and indicate test success or failure. The boot process runs for approximately

60 seconds.

You can invoke the Boot menu after the first part of the POST is completed.

From the Boot menu, you can perform configuration tasks such as resetting

the system to factory defaults, activating the backup image, or recovering a

password. For more information about the Boot menu functions, refer to the

CLI Reference Guide.

Getting Started Guide 15

Performing the N2128PX-ON Initial Configuration

The initial configuration procedure is based on the following assumptions:

• The Dell Networking switch was never configured before.

• The Dell Networking switch booted successfully.

• The console connection was established, and the

Dell Easy Setup Wizard

prompt appears on the screen of a VT100 terminal or terminal equivalent.

The initial switch configuration is performed through the console port. After

the initial configuration, you can manage the switch from the already-

connected console port or remotely through an interface defined during the

initial configuration.

NOTE: The switch is not configured with a default user name, password, or IP

address.

Before setting up the initial configuration of the switch, obtain the following

information from your network administrator:

• The IP address to be assigned to the management interface.

• The IP subnet mask for the network.

• The IP address of the management interface default gateway.

These settings are necessary to allow the remote management of the switch

through Telnet (Telnet client) or HTTP (Web browser).

Enabling Remote Management

On the N2128PX-ON/N3132PX-ON switches, you can use any of the switch

ports on the front panel for in-band management. By default, all in-band

ports are members of VLAN 1.

The Dell Easy Setup Wizard includes prompts to configure network

information for the VLAN 1 interface on the N2128PX-ON switch. You can

assign a static IP address and subnet mask or enable DHCP and allow a

network DHCP server to assign the information.

Refer to the CLI Reference Guide for commands to configure network

information.

16 Getting Started Guide

Initial Configuration Procedure

Perform the initial configuration by using the Dell Easy Setup Wizard or by

using the CLI. The wizard automatically starts when the switch configuration

file is empty. You can exit the wizard at any point by entering [ctrl+z], but all

configuration settings specified will be discarded, and the switch will use the

default values.

NOTE: If you do not run the Dell Easy Setup Wizard or do not respond to the initial

Easy Setup Wizard prompt within 60 seconds, the switch enters CLI mode. You must

reset the switch with an empty startup configuration in order to rerun the Dell Easy

Setup Wizard.

For more information about performing the initial configuration by using the

CLI, refer to the CLI Reference Guide. This Getting Started Guide shows how

to use the Dell Easy Setup Wizard for initial switch configuration. The wizard

sets up the following configuration on the switch:

• Establishes the initial privileged user account with a valid password. The

wizard configures one privileged user account during the setup.

• Enables CLI login and HTTP access to use the local authentication setting

only.

• Sets up the IP address for the VLAN 1 routing interface, of which all

in-band ports are members.

• Sets up the SNMP community string to be used by the SNMP manager at

a given IP address. You may choose to skip this step if SNMP management

is not used for this switch.

• Allows you to specify the network management system IP address or

permit management access from all IP addresses.

• Configures the default gateway IP address for the VLAN 1 interface.

Getting Started Guide 17

Example Session

This section describes a Dell Easy Setup Wizard session. The following

values are used by the example session:

• The SNMP community string to be used is

public

.

• The network management system (NMS) IP address is

10.1.2.100

.

• The user name is

admin

, and the password is

admin123

.

• The IP address for the VLAN 1 routing interface is

10.1.1.200

with a

subnet mask of

255.255.255.0

.

• The default gateway is

10.1.1.1.

The setup wizard configures the initial values as defined above. After

completing the wizard, the switch is configured as follows:

• SNMPv2 is enabled and the community string is set up as defined above.

SNMPv3 is disabled by default.

• The admin user account is set up as defined.

• A network management system is configured. From the management

station, you can access the SNMP, HTTP, and CLI interfaces. You may also

choose to allow all IP addresses to access these management interfaces by

choosing the (0.0.0.0) IP address.

• An IP address is configured for the VLAN 1 routing interface.

• A default gateway address is configured.

NOTE: In the following example, the possible user options or default values are

enclosed in [ ]. If you press <Enter> with no options defined, the default value is

accepted. Help text is in parentheses.

18 Getting Started Guide

Dell Easy Setup Wizard Console Example

The following example contains the sequence of prompts and responses

associated with running an example Dell Easy Setup Wizard session, using

the input values listed earlier.

After the switch completes the POST and is booted, the following dialog

appears:

Unit 1 - Waiting to select management unit)>

___________Dell SupportAssist EULA__________________

I accept the terms of the license agreement. You can

reject the license agreement by configuring this

command 'eula-consent support-assist reject'.

By installing SupportAssist, you allow Dell to save

your contact information (e.g. name, phone number

and/or email address) which would be used to provide

technical support for your Dell products and services

Dell may use the information for providing

recommendations to improve your IT infrastructure.

Dell SupportAssist also collects and stores machine

diagnostic information, which may include but is not

limited to configuration information, user supplied

contact information, names of data volumes, IP

addresses, access control lists, diagnostics &

performance information, network configuration

information, host/server configuration & performance

information and related data (Collected Data) and

transmits this information to Dell. By downloading

SupportAssist and agreeing to be bound by these terms

and the Dell end user license agreement, available at:

http://www.dell.com/aeula, you agree to allow Dell to

provide remote monitoring services of your IT

environment and you give Dell the right to collect the

Collected Data in accordance with Dell's Privacy

Policy, available at:

http://www.dell.com/privacypolicycountryspecific, in

order to enable the performance of all of the various

functions of SupportAssist during your entitlement to

Getting Started Guide 19

receive related repair services from Dell. You further

agree to allow Dell to transmit and store the

Collected Data from SupportAssist in accordance with

these terms. You agree that the provision of

SupportAssist may involve international transfers of

data from you to Dell and/or to Dell's affiliates,

subcontractors or business partners. When making such

transfers, Dell shall ensure appropriate protection is

in place to safeguard the Collected Data being

transferred in connection with SupportAssist. If you

are downloading SupportAssist on behalf of a company

or other legal entity, you are further certifying to

Dell that you have appropriate authority to provide

this consent on behalf of that entity. If you do not

consent to the collection, transmission and/or use of

the Collected Data, you may not download, install or

otherwise use SupportAssist.

________AeroHive HiveManager NG EULA________________

This switch includes a feature that enables it to work

with HiveManager (an optional management suite), by

sending the switch's service tag number and IP Address

to HiveManager to authenticate your entitlement to use

HiveManager. If you wish to disable this feature, you

should run command 'eula-consent hiveagent reject'

immediately upon powering up the switch for the first

time, or at any time thereafter.

Applying Global configuration, please wait...

Welcome to Dell Easy Setup Wizard

The setup wizard guides you through the initial switch

configuration, and gets you up and running as quickly

as possible. You can skip the setup wizard, and enter

CLI mode to manually configure the switch. You must

respond to the next question to run the setup wizard

within 60 seconds, otherwise the system will continue

20 Getting Started Guide

with normal operation using the default system

configuration. Note: You can exit the setup wizard at

any point by entering [ctrl+z].

Would you like to run the setup wizard (you must

answer this question within 60 seconds)? [Y/N] y

Step 1:

The system is not set up for SNMP management by

default. To manage the switch using SNMP (required for

Dell Network Manager) you can

. Set up the initial SNMP version 2 account now.

. Return later and set up other SNMP accounts. (For

more information on setting up an SNMP version 1 or

3 account, see the user documentation).

Would you like to set up the SNMP management interface

now? [Y/N] y

To set up the SNMP management account you must specify

the management system IP address and the “community

string” or password that the particular management

system uses to access the switch. The wizard

automatically assigns the highest access level

[Privilege Level 15] to this account. You can use Dell

Network Manager or other management interfaces to

change this setting, and to add additional management

system information later. For more information on

adding management systems, see the user documentation.

To add a management station:

Please enter the SNMP community string to be used.

[public]: public

NOTE: If it is configured, the default access level is set to the highest available

access for the SNMP management interface. Initially only SNMPv2 will be

activated. SNMPv3 is disabled until you return to configure security access for

SNMPv3 (e.g. engine ID, view, etc.).

Please enter the IP address of the Management System

(A.B.C.D) or wildcard (0.0.0.0) to manage from any

Management Station. [0.0.0.0]: 10.1.2.100

Page is loading ...

Dell EMC PowerSwitch N3100 Series Owner's manual

This manual is also suitable for

Dell EMC PowerSwitch N3100 Series Owner's manual

in other languages

Related papers

Other documents