Conrad DIN-rail bracket Compatible Owner's manual

Conrad
Brand
Conrad
Model
DIN-rail bracket Compatible
Category
Coffee making accessories
Type
Owner's manual

This manual is also suitable for

Page is loading ...
Controller Boards
• Please refer to the “Technical Data” section for information about supported controller boards.
• Use the supplied mounting posts and screws to attach your controller board.
• Mounting points are indicated below.
PI = Raspberry PI and ASUS
Tinkerboard
U = Arduino UNO
MG = Arduino Mega
3.5” Drive Bay Accessories
Various 3.5” drive bay form factor computer accessories can also be mounted to the adaptor
e.g. internal USB hub.
Care and Cleaning
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these could
damage the housing or stop the product from functioning properly.
• Use a dry, lint-free cloth to clean the product.
Disposal
The product must not be disposed of with the household waste. At the end of its
service life, dispose of the product according to the relevant statutory regulations.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical Data
Controller boards .................................. Raspberry Pi 1 Model A+, Pi 1 Model B+,
Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+,
Pi 3 Model A+, Asus Tinkerboard, Arduino UNO,
and Arduino Mega boards
Drive bay accessories .......................... 3.5” drive bay form factor computer accessories,
e.g. USB internal hub, USB RS232
Material ................................................. ABS + PC
DIN rail ..................................................35 mm (C45)
Operating conditions .............................+10 to +60 ºC, 30 – 80 % RH
Storage conditions ................................ -40 to +70 ºC, 30 – 80 % RH
Dimensions (W x H x D) .......................107 x 99 x 40 mm
Weight ..................................................95 g
Operating Instructions
Raspberry PI DIN-Rail Mount Adaptor
Item no. 1897728
Intended Use
The product is intended to be used as a DIN-rail mount adaptor and is suitable for industrial
use. It supports various micro controller boards and 3.5” drive bay form factor computer
accessories such as an internal USB hub.
For safety purposes, you must not rebuild and/or modify this product. Using the product for
purposes other than those described above may damage the product. In addition, improper use
can cause hazards such as a short circuit, fire or electric shock. Read the instructions carefully
and store them in a safe place. Only make this product available to third parties together with
its operating instructions.
This product complies with statutory, national and European regulations. All company and
product names are trademarks of their respective owners. All rights reserved.
Delivery Content
• DIN rail mount adaptor
• 6x Mounting posts
• 12x Mounting screws
• Operating instructions
Up-to-Date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of Symbols
The symbol with an exclamation mark in a triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
Safety Instructions
Read the operating instructions and safety information carefully. If you do
not follow the safety information and information on proper handling in these
operating instructions, we will assume no liability for any resulting personal
injury or damage to property. Such cases will invalidate the warranty/
guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. It may become a
dangerous toy for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
may damage the product.
• Always observe the safety information and operating instructions of any other
devices which are connected to the product.
• Consult a technician if you are not sure how to use or connect the product, or if
you have concerns about safety.
• Maintenance, modifications and repairs must be done by a technician or a
specialist repair centre.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microlming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE. *1897728_v2_0219_02_dh_m_en
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Conrad DIN-rail bracket Compatible Owner's manual

Conrad
Brand
Conrad
Model
DIN-rail bracket Compatible
Category
Coffee making accessories
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents