Tripp Lite B140-110 Owner's manual

Owner’s Manual

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

DVI over Cat5 Extenders

and Extender/Splitters

Extender Kit Models:

B140-101, B140-1P1-WP-1, B140-101X, B140-1A1-WP

Local Unit Models: B140-002 and B140-004

Remote Unit Models: B140-1P0, B140-1P0-WP-1,

B140-1A0, B140-1A0-WP-1 and B140-110

Warranty

Registration:

chance to win a FREE Tripp Lite

product—www.tripplite.com/warranty

Package Contents 2

Product Features 2

Mounting (Optional) 8

Standard Extender Kit Installation 9

Extender Kit with Remote/Repeater Installation 11

(B140-101X and B140-1A1-WP extender kits only)

Standard Extender/Splitter Installation 14

Extender/Splitter with Remote/Repeater Installation 17

(B140-1A0 and B140-1A0-WP-1 remote receiver units only)

Extender/Splitter Daisy-Chain Installation 20

Extender/Splitter Daisy-Chain with Remote/Repeater Installation 22

(B140-004 extender/splitter, and B140-1A0 and B140-1A0-WP

remote receivers only)

Warranty & Warranty Registration 27

201110026-93-3094-EN.indd 1 11/3/2011 11:37:06 AM

Package Contents

Product Features

B140-101

B140-1P1-WP-1

B140-101X

B140-1A1-WP

B140-002

B140-004

B140-1A0

B140-1A0-WP-1

B140-1P0

B140-1P0-WP-1

B140-110

Local Unit (L), Remote Unit

(R), or Both (B)

B B B B L L R R R R R

External Power Supplies

(0, 1, or 2)

0 0 1 2 1 1 1 1 0 0 1

Mounting Hardware X X X X X

Wallplate Screws X X X X

Screwdriver for Equalization

Adjustment

X X X X X

DVI Daisy-chain Cable X

All

• SupportDVI-DSingle-Linkvideoresolutionsupto1920x1080(60Hz)

• Plug-and-play;nosoftwareordriversrequired

• Compatiblewithallmajoroperatingsystems

•HDCPcompatible

B140-101

• DVIoverCat5PassiveExtenderKit(Box-style)

• Extenda1024x768(60Hz)signalupto100ft.fromthesource,or

a1920x1080(60Hz)signalupto50ft.fromthesource

• Noexternalpowerrequired

201110026-93-3094-EN.indd 2 11/3/2011 11:37:06 AM

Product Features

B140-1P1-WP-1

• DVIoverCat5PassiveExtenderWallplateKit

• Extenda1024x768(60Hz)signalupto75ft.fromthesource,ora

1920x1080(60Hz)signalupto50ft.fromthesource

• RJ45-stylewallplatesallowfortheuseofstandardCat5e/6patch

cables;110punchdownconnectionnotrequired

• Noexternalpowerrequired

B140-101X

• DVIoverCat5ActiveExtenderKit(Box-style)

• Extenda1024x768(60Hz)signalupto200ft.fromthesource,or

a1920x1080(60Hz)signalupto150ft.fromthesource

• Remotereceiverunitfeaturesabuilt-inEqualizationcontrolforvideo

image adjustment

• Includesmountinghardwarethatallowsremoteunittobe

wallmounted, rackmounted or pole mounted

B140-1A1-WP

• DVIoverCat5ActiveExtenderWallplateKit

• Extenda1024x768(60Hz)signalupto200ft.fromthesource,or

a1920x1080(60Hz)signalupto150ft.fromthesource

• Remotereceiverunitfeaturesabuilt-inEqualizationcontrolforvideo

image adjustment

• RJ45-stylewallplatesallowfortheuseofstandardCat5e/6patch

cables;110punchdownconnectionnotrequired

201110026-93-3094-EN.indd 3 11/3/2011 11:37:06 AM

Product Features

B140-002

• 2-PortDVIoverCat5Extender/SplitterLocalTransmitterUnit

(Box-style)

• SplitsaDVI-DSingle-Linksignalinto2separatesignals

• Workswithremote/repeaterandreceiverunitstoextendaDVI-D

Single-Linksignalpassedthe16-ft.(5m.)distancelimitation

• Includesmountinghardwarethatallowstheunittobewallmounted,

rackmounted or pole mounted

B140-004

• 4-PortDVIoverCat5Extender/SplitterLocalTransmitterUnit

(Box-style)

• SplitsaDVI-DSingle-Linksignalinto4

• AdditionalDVIportcanbeusedtoconnectalocalmonitororto

daisy-chain additional B140-004 units. Up to 3 B140-004 units

can be daisy-chained together to increase the number of connected

monitors

• Workswithremote/repeaterandreceiverunitstoextendaDVI-D

Single-Linksignalpassedthe16ft.(5m.)distancelimitation

• Includesmountinghardwarethatallowstheunittobewallmounted,

rackmounted or pole mounted

• Upto3B126-004unitscanbemountedinaB132-004-RB

1U rackmount bracket

201110026-93-3094-EN.indd 4 11/3/2011 11:37:06 AM

Product Features

B140-1A0

• DVIoverCat5ActiveExtenderRemoteReceiverUnit(Box-style)

• WorkswithB140-002andB140-004extender/splitterstoextenda

1024x768(60Hz)signalupto200ft.fromthesource,ora

1920x1080(60Hz)signalupto150ft.fromthesource

• Built-inEqualizationcontrolforvideoimageadjustment

• Includesmountinghardwarethatallowstheunittobewallmounted,

rackmounted or pole mounted

B140-1A0-WP-1

• DVIoverCat5ActiveExtenderWallplate

• WorkswithB140-002andB140-004extender/splitterstoextenda

1024x768(60Hz)signalupto200ft.fromthesource,ora

1920x1080(60Hz)signalupto150ft.fromthesource

• Built-inEqualizationcontrolforvideoimageadjustment

• RJ45-stylewallplateallowsfortheuseofstandardCat5e/6patch

cables;110punchdownconnectionnotrequired

B140-1P0

• DVIoverCat5PassiveExtenderRemoteReceiverUnit(Box-style)

• WorkswithB140-002andB140-004extender/splitterstoextenda

1024x768(60Hz)signalupto100ft.fromthesource,ora

1920x1080(60Hz)signalupto50ft.fromthesource

• Built-inDVIcable;separateDVIcablenotrequired

• Noexternalpowerrequired

201110026-93-3094-EN.indd 5 11/3/2011 11:37:06 AM

Product Features

B140-1P0-WP-1

• DVIoverCat5PassiveExtenderWallplate

• WorkswithB140-002andB140-004extender/splitterstoextenda

1024x768(60Hz)signalupto75ft.fromthesource,ora1920x

1080(60Hz)signalupto50ft.fromthesource

• RJ45-stylewallplateallowsfortheuseofstandardCat5e/6patch

cables;110punchdownconnectionnotrequired.

• Noexternalpowerrequired

B140-110

• DVIoverCat5ExtenderRemote/RepeaterUnit(Box-style)

• ExtendsandexpandsyourTrippLiteDVIoverCat5installation,

allowing you to locate multiple monitors at different points in a chain

of up to 700 ft.

• Extendsa1024x768(60Hz)signalupto175ft.,ora1920x1080

(60Hz)signalupto125ft.fromthelocaltransmitterunittotherst

remote/repeater unit in the installation

• Extendsa1024x768(60Hz)signaluptoanadditional175ft.,or

a1920x1080(60Hz)signaluptoanadditional125ft.fromeach

remote/repeater unit to the next unit in the chain. In a full 4-level

daisychaininstallation,a1024x768(60Hz)signalcanbeextended

upto700ft.,ora1920x1080(60Hz)signalupto500ft.fromthe

source to the last remote unit in the chain.

• Connectupto4remoteunits(3remote/repeatersand1receiver),

with a monitor located at each point in the chain

• Built-inEqualizationcontrolforvideoimageadjustment

• Includesmountinghardwarethatallowstheunittobewallmounted,

rackmounted or pole mounted

201110026-93-3094-EN.indd 6 11/3/2011 11:37:06 AM

Product Features

Optional Accessories:

• B132-004-RB1URackmountBracket

• N202-SeriesCat624AWG,solidwirepatchcables

• P561-SeriesDVI-DSingle-Linkcables

201110026-93-3094-EN.indd 7 11/3/2011 11:37:06 AM

Mounting (Optional)

The B140-101X, B140-002, B140-004, B140-1A0 and B140-110

come with mounting hardware that allows them to be mounted in

a variety of ways. The following images show the different ways the

included mounting brackets can be attached for different mounting

methods. Note: The B140-004 can also be mounted to a Tripp Lite

B132-004-RB 1U Rackmount Bracket. Up to 3 B140-004 local units

can be connected to a B132-004-RB.

Wallmount

19” Rackmount Pole Mount

201110026-93-3094-EN.indd 8 11/3/2011 11:37:08 AM

TO DVI SOURCE

RJ45 JACK

Cat5/5e/6

PATCH CABLE

LOCAL UNIT

POWER

JACK

REMOTE UNIT

TO DVI MONITOR

B140-101 — Up to 100 ft. at 1024 x 768 (60 Hz), or up to 50 ft. at 1920 x 1080 (60 Hz)

B140-1P1-WP-1 — Up to 75 ft. at 1024 x 768 (60 Hz), or up to 50 ft. at 1920 x 1080 (60 Hz)

B140-101X and B140-1A1-WP — Up to 200 ft. at 1024 x 768 (60 Hz), or up to 150 ft. at 1920 x 1080 (60 Hz)

Standard Extender Kit Installation

(B140-101, B140-1P1-WP-1, B140-101X, B140-1A1-WP)

Notes:

1. The diagram below shows a B140-101X installation. Installation will

be the same for the B140-1A1-WP. Installation will be similar for the

B140-101 and B140-1P1-WP-1, except that they will not require

external power.

2. Test to make sure that the entire installation works properly before

pulling cables through ceilings/walls.

3. To achieve maximum distance and performance, use 24 AWG Solid

Wire Cat5e/6 cable. Using stranded wire cable, or cable with a gauge

(AWG) size higher than 24 AWG, will result in lesser performance

and shorter extension distance. Tripp Lite N202-Series (Cat6) patch

cables are made with 24 AWG Solid Wire cabling.

Make sure power to the DVI source is turned off.

Connect the built-in DVI connector on the B140-101 or B140-101X

local unit to the DVI source, or connect the B140-1A1-WP or

B140-1P1-WP-1 local unit to the source using a Tripp Lite

P561-SeriesDVIcable.

201110026-93-3094-EN.indd 9 11/3/2011 11:37:08 AM

Standard Extender Kit Installation

B140-1A1-WP only: Connect the external power supply to the local

unit and plug it into a Trip Lite Surge Suppressor, Power Distribution

Unit(PDU),orUninterruptablePowerSupply(UPS).TheGreen

Power LED will illuminate.

ConnecttheRJ45portsonthelocalandremoteunitsusing

Cat5e/6cable.

Connect the built-in DVI connector on the B140-101 remote unit to

the DVI monitor, or connect the B140-1A1-WP, B140-1P1-WP-1 or

B140-101X remote unit to the monitor using a Tripp Lite

P561-SeriesDVIcable.

B140-1A1-WP and B140-101X only: Connect the external

power supply to the remote unit and plug it into a Tripp Lite Surge

Suppressor, Power Distribution Unit (PDU) or Uninterruptible Power

Supply(UPS).TheGreenRJ45LEDontheB140-101Xremoteunit

willilluminatetoindicateitisreceivingpower.TheGreenPowerLED

will illuminate on the B140-1A1-WP remote unit.

TurnonthepowertotheDVIsource.TheGreenRJ45LEDswill

illuminate on the B140-101 and B140-101X units, and the Power

LEDs will illuminate on the B140-1P1-WP-1 units to indicate that

theyarereceivingpower.TheOrangeRJ45LEDwillilluminateonthe

B140-101X remote unit to indicate it is receiving a signal from the

source. The Orange Activity LEDs will illuminate on the

B140-1A1-WP units.

B140-1A1-WP and B140-101X only: If necessary, adjust the

Equalization control on the remote unit to improve the video image.

Note: An improper Equalization setting can cause the monitor not

to display a picture at all. Try each Equalization setting until an

acceptable image is displayed.

201110026-93-3094-EN.indd 10 11/3/2011 11:37:09 AM

DVI SOURCE

B140-1A1-WP LOCAL

TRANSMITTER

B140-1A1-WP REMOTE

RECEIVER

B140-110

REMOTE

REPEATER

B140-110

REMOTE

REPEATER

B140-110

REMOTE

REPEATER

Up to 175 ft. at 1024 x 768 (60Hz)

Up to 125 ft. at 1920 x 1080 (60Hz)

Up to 175 ft. at 1024 x 768 (60Hz)

Up to 125 ft. at 1920 x 1080 (60Hz)

Extender Kit with Remote/Repeater

Installation (B140-101X and B140-1A1-WP extender kits only)

Notes:

1. Test to make sure the entire installation works properly before pulling

cables through ceilings/walls.

2. To achieve maximum distance and performance, use 24 AWG solid

wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable

with a gauge (AWG) size higher than 24 AWG, will result in shorter

extension distance. All Tripp Lite N202-Series Cat6 cables are made

with 24 AWG solid wire cabling.

3. The installation diagram shows a B140-1A1-WP. The B140-101X

installation is the same, except its local unit does not require power.

Make sure the DVI source is powered OFF.

Connect the built-in DVI connector on the B140-101X local unit to

theDVIsource;or,connecttheDVIsourcetotheINPUTportonthe

B140-1A1-WPlocalunitusingaTrippLiteP561-SeriesDVI-DSingle

Link Cable.

B140-1A1-WP only: Connect the external power supply to the local

unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The

GreenPowerLEDwillilluminate.

201110026-93-3094-EN.indd 11 11/3/2011 11:37:09 AM

UsingCat5e/6cable,connecttheRJ45portonthelocalunittothe

RJ45INPUTportontheB140-110remote/repeaterunit.

Connect a monitor to the DVI OUTPUT port on the remote/repeater

unitusingaTrippLiteP561-SeriesDVI-DSingle-LinkCable.

Connect the external power supply to the remote/repeater unit and

plugitintoaTrippLiteSurgeSuppressor,PDUorUPS.TheGreen

PowerLEDandtheGreenRJ45LEDsilluminatetoindicatetheunit

is receiving power.

Up to 4 units can be daisy-chained (3 remote/repeaters and 1 receiver).

Toconnectadditionalremote/repeaterunits,proceedtostep7.Tonish

your installation with the B140-101X or B140-1A1-WP remote receiver

unit, proceed to step 11.

UsingCat5e/6cable,connecttheRJ45OUTPUTportontherst

remote/repeaterunittotheRJ45INPUTportonasecondremote/

repeater unit.

Connect a monitor to the DVI OUTPUT port on the remote/repeater

unitthatyoujustaddedusingaTrippLiteP561-SeriesDVI-D

Single-Link Cable.

Connect the external power supply to the remote/repeater unit and

plugitintoaTrippLiteSurgeSuppressor,PDUorUPS.TheGreen

PowerLEDandtheGreenRJ45LEDsilluminatetoindicatetheunit

is receiving power.

To add a third remote/repeater unit, repeat steps 7 through 9.

TonishyourinstallationwiththeB140-101XorB140-1A1-WP

remote receiver unit, proceed to step 11.

Extender Kit with Remote/Repeater

Installation (B140-101X and B140-1A1-WP extender kits only)

201110026-93-3094-EN.indd 12 11/3/2011 11:37:09 AM

UsingCat5e/6cable,connecttheRJ45OUTPUTportonthelast

remote/repeaterunittotheRJ45INPUTportoftheB140-101Xor

B140-1A1-WP remote receiver unit.

Connect a monitor to the DVI OUTPUT port on the remote receiver

unitusingaTrippLiteP561-SeriesDVI-DSingle-LinkCable.

Connect the external power supply to the remote receiver unit and

plugitintoaTrippLiteSurgeSuppressor,PDUorUPS.TheGreen

RJ45LEDontheB140-101Xremotereceiver,ortheGreenPower

LED on the B140-1A1-WP remote wallplate, illuminates to indicate

the unit is receiving power from the external power supply.

Turn on the power to the DVI source. The Orange LEDs on the

B140-1A1-WP units illuminate to indicate a signal is being received

fromthesource.TheOrangeRJ45LEDsontheB140-101Xand

B140-110 units illuminates to indicate a signal is being received

from the source.

If necessary, use the Equalization control on the remote/repeater

unit(s) and remote receiver unit to adjust the video image. Note: An

improper Equalization setting can cause the monitor not to display

a picture at all. Try each Equalization setting until an acceptable

picture is displayed.

Extender Kit with Remote/Repeater

Installation (B140-101X and B140-1A1-WP extender kits only)

201110026-93-3094-EN.indd 13 11/3/2011 11:37:09 AM

B140-004

B140-1A0

B140-1P0

B140-1A0-WP-1

Up to 200 ft. at 1024 x 768 (60Hz)

Up to 150 ft. at 1920 x 1080 (60Hz)

Up to 100 ft. at 1024 x 768 (60Hz)

Up to 50 ft. at 1920 x 1080 (60Hz)

Up to 75 ft. at 1024 x 768 (60Hz)

Up to 50 ft. at 1920 x 1080 (60Hz)

DVI OVER Cat5

EXTENDER

REMOTE UNIT

MODEL: B140-1P0

B140-1P0-WP-1

Standard Extender/Splitter Installation

Notes:

1. The diagram below shows a B140-004 installation. Installation will

be the same when using a B140-002, except that the B140-002

has fewer RJ45 ports and no local monitor port.

2. Test to make sure that the entire installation works properly before

pulling cables through ceilings/walls.

3. To achieve maximum distance and performance, use 24 AWG solid

wire Cat5e/6 cable. Using stranded wire cable, or cable with a gauge

(AWG) size higher than 24 AWG, will result in lesser performance

and shorter extension distance. Tripp Lite N202-Series (Cat6) patch

cables are made with 24 AWG solid wire cabling.

201110026-93-3094-EN.indd 14 11/3/2011 11:37:10 AM

Standard Extender/Splitter Installation

Make sure the DVI source is powered OFF.

Connect the DVI source to the DVI port on the B140-002 or

B140-004labeledINPUTusingaTrippLiteP561-SeriesDVI-D

Single-Link Cable.

Optional for B140-004: Connect a DVI monitor to the DVI port on

theB140-004markedLOCALusingaTrippLiteP561-SeriesDVI-D

Single-Link Cable.

Connect the external power supply to the B140-002 or B140-004

local unit and plug it into a Tripp Lite Surge Suppressor, PDU or

UPS.TheGreenRJ45LEDsandRedPowerLEDontheB140-004

will illuminate to indicate power is being received from the external

powersupply.TheGreenRJ45LEDsontheB140-002willilluminate

to indicate power is being received from the external power supply.

UsingCat5e/6cable,connectoneoftheRJ45outputportsonthe

localunittotheRJ45inputportontheB140-1P0,B140-1A0,

B140-1P0-WP-1 or B140-1A0-WP-1 remote unit.

Repeatstep5foreachadditionalremoteunityouareconnecting.

B140-1A0 and B140-1A0-WP-1 only: Connect the external

power supply to the B140-1A0 or B140-1A0-WP-1 and plug it into

aTrippLiteSurgeSuppressor,PDUorUPS.TheGreenRJ45LED

ontheB140-1A0andtheGreenLEDontheB140-1A0-WP-1will

illuminate to indicate that the unit is receiving power.

Repeat step 7 for each additional B140-1A0 or B140-1A0-WP-1 in

the installation.

201110026-93-3094-EN.indd 15 11/3/2011 11:37:10 AM

ConnecttheB140-1P0DVI-DSingle-Linkconnectortothemonitor;

or, connect the B140-1P0-WP-1, B140-1A0 or B140-1A0-WP-1 to

themonitorusingaTrippLiteP561-SeriesDVI-DSingle-LinkCable.

TheGreenRJ45LEDontheB140-1P0andtheGreenLEDonthe

B140-1P0-WP-1 illuminate to indicate the unit is receiving power

from the monitor.

Repeat step 9 for each additional monitor you are connecting.

TurnonthepowertotheDVIsource.TheOrangeRJ45LEDs

illuminate on the B140-002, B140-004 and B140-1A0, and the

Orange LED illuminates on the B140-1A0-WP-1 to indicate the unit

is receiving a signal from the source. The image should now be

displayed on the connected monitors.

If necessary, use the Equalization control on the B140-1A0 or

B140-1A0-WP-1 to adjust the video image. Note: An improper

Equalization setting can cause the monitor not to display a picture

at all. Try each Equalization setting until an acceptable image is

displayed.

Standard Extender/Splitter Installation

201110026-93-3094-EN.indd 16 11/3/2011 11:37:10 AM

OPTIONAL LOCAL

MONITOR

B140-004 LOCAL

TRANSMITTER

B140-110 REMOTE/

REPEATER

B140-110 REMOTE/

REPEATER

B140-110 REMOTE/

REPEATER

Up to 175 ft. at 1024 x 768 (60Hz)

Up to 125 ft. at 1920 x 1080 (60Hz)

Up to 175 ft. at 1024 x 768 (60Hz)

Up to 125 ft. at 1920 x 1080 (60Hz)

DVI SOURCE

B140-110 REMOTE/

REPEATER

B140-110 REMOTE/

REPEATER

B140-110 REMOTE/

REPEATER

B140-110 REMOTE/

REPEATER

B140-110 REMOTE/

REPEATER

B140-110 REMOTE/

REPEATER

B140-1A0-WP-1

REMOTE RECEIVER

B126-1A0-WP-1

REMOTE RECEIVER

B126-1A0

REMOTE RECEIVER

B140-110 REMOTE/

REPEATER

B140-110 REMOTE/

REPEATER

B140-110 REMOTE/

REPEATER

B126-1A0

REMOTE RECEIVER

Notes:

1. Test to make sure the entire installation works properly before pulling

cables through ceilings/walls.

2. To achieve maximum distance and performance, use 24 AWG solid

wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable

with a gauge (AWG) size higher than 24 AWG, will result in shorter

extension distance. All Tripp Lite N202-Series Cat6 cables are made

with 24 AWG solid wire cabling.

3. The installation diagram shows the B140-004. The B140-002

installation will be the same, except there are only 2 remote ports

and there is no local monitor port.

Extender/Splitter with Remote/Repeater Installation

(B140-1A0 and B140-1A0-WP-1 remote receiver units only)

Make sure the DVI source is powered OFF.

201110026-93-3094-EN.indd 17 11/3/2011 11:37:12 AM

Extender/Splitter with Remote/Repeater Installation

(B140-1A0 and B140-1A0-WP-1 remote receiver units only)

ConnecttheDVIsourcetotheINPUTportontheB140-002or

B140-004usingaTrippLiteP561-SeriesDVI-DSingle-LinkCable.

Optional for B140-004: Connect a local monitor to the DVI

OUTPUTportusingaTrippLiteP561-SeriesDVI-DSingle-LinkCable.

Connect the external power supply to the local unit and plug it into

aTrippLiteSurgeSuppressor,PDUorUPS.TheGreenRJ45LEDs

illuminate to indicate power is being received from the external

power supply. An additional Red LED on the B140-004 also

illuminates to indicate that power is being received.

UsingCat5e/6cable,connectoneoftheRJ45outputportsonthe

localunittotheRJ45inputportontheB140-110remote/repeater

unit.

Connect a monitor to the DVI OUTPUT port on the remote/repeater

unitusingaTrippLiteP561-SeriesDVI-DSingle-LinkCable.

Connect the external power supply to the remote/repeater unit and

plugitintoaTrippLiteSurgeSuppressor,PDUorUPS.TheGreen

PowerLEDandtheGreenRJ45LEDsilluminatetoindicatetheunit

is receiving power.

Up to 4 units can be daisy-chained (3 remote/repeaters and 1 receiver).

Toconnectadditionalremote/repeaterunits,proceedtostep8.Tonish

your installation with a B140-1A0 or B140-1A0-WP-1 remote receiver

unit, proceed to step 12.

UsingCat5e/6cable,connecttheRJ45OUTPUTportontherst

remote/repeaterunittotheRJ45INPUTportonasecondremote/

repeater unit.

Connect a monitor to the DVI OUTPUT port on the remote/repeater

unitthatyoujustaddedusingaTrippLiteP561-SeriesDVI-DSingle-

Link Cable.

201110026-93-3094-EN.indd 18 11/3/2011 11:37:12 AM

Extender/Splitter with Remote/Repeater Installation

(B140-1A0 and B140-1A0-WP-1 remote receiver units only)

Connect the external power supply to the remote/repeater unit and

plugitintoaTrippLiteSurgeSuppressor,PDUorUPS.TheGreen

PowerLEDandtheGreenRJ45LEDsilluminatetoindicatetheunit

is receiving power.

To add a third remote/repeater unit, repeat steps 8 through 10. To

nishyourinstallationwithaB140-1A0orB140-1A0-WP-1remote

receiver unit, proceed to step 12.

UsingCat5e/6cable,connecttheRJ45OUTPUTportonthelast

remote/repeaterunittotheRJ45INPUTportonaB140-1A0or

B140-1A0-WP-1 remote receiver unit.

Connect a monitor to the DVI OUTPUT port on the remote receiver

unitusingaTrippLiteP561-SeriesDVI-DSingle-LinkCable.

Connect the external power supply to the remote receiver unit and

plugitintoaTrippLiteSurgeSuppressor,PDUorUPS.TheGreen

RJ45LEDsontheB140-1A0andtheGreenLEDontheB140-1A0-

WP-1 illuminate to indicate that the unit is receiving power.

Repeatsteps5through14foreachadditionalRJ45outputporton

the local transmitter unit.

TurnonthepowertotheDVIsource.TheOrangeRJ45LEDson

the local transmitter, remote/repeater and B140-1A0 illuminate

to indicate a signal is being received from the source. The Orange

LED on the B140-1A0-WP-1 illuminates to indicate a signal is being

received from the source.

If necessary, use the Equalization control on the remote/repeater

unit(s) and remote receiver unit to adjust the video image. Note: An

improper Equalization setting can cause the monitor not to display

a picture at all. Try each Equalization setting until an acceptable

picture is displayed.

201110026-93-3094-EN.indd 19 11/3/2011 11:37:12 AM

Level 1

Level 2

Level 3

OPTIONAL LOCAL

MONITOR

B140-1P0 — Up to 100 ft. at 1024 x 768 (60 Hz), or up to 50 ft. at 1920 x 1080 (60 Hz)

B140-1P0-WP-1 — Up to 75 ft. at 1024 x 768 (60 Hz), or up to 50 ft. at 1920 x 1080 (60 Hz)

B140-1A0 and B140-1A0-WP-1 — Up to 200 ft. at 1024 x 768 (60 Hz), or up to 150 ft. at 1920 x 1080 (60 Hz)

Extender/Splitter Daisy-Chain Installation

(B140-004 only)

Notes:

1. Test to make sure that the entire installation works properly before

pulling cables through ceilings/walls.

2. To achieve maximum distance and performance, use 24 AWG solid

wire Cat5e/6 cable. Using stranded wire cable, or cable with a gauge

(AWG) size higher than 24 AWG, will result in lesser performance

and shorter extension distance. Tripp Lite N202-Series (Cat6) patch

cables are made with 24 AWG solid wire cabling.

201110026-93-3094-EN.indd 20 11/3/2011 11:37:13 AM

Tripp Lite B140-110 Owner's manual

Related papers

Other documents