Tripp Lite B140-004 Owner's manual

B140-004
Tripp Lite
Brand
Tripp Lite
Model
B140-004
Category
AV extenders
Type
Owner's manual
1
Owner’s Manual
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2011 Tripp Lite. All rights reserved.
DVI over Cat5 Extenders
and Extender/Splitters
Extender Kit Models:
B140-101, B140-1P1-WP-1, B140-101X, B140-1A1-WP
Local Unit Models: B140-002 and B140-004
Remote Unit Models: B140-1P0, B140-1P0-WP-1,
B140-1A0, B140-1A0-WP-1 and B140-110
Warranty
Registration:
register online today for a
chance to win a FREE Tripp Lite
product—www.tripplite.com/warranty
Package Contents 2
Product Features 2
Mounting (Optional) 8
Standard Extender Kit Installation 9
Extender Kit with Remote/Repeater Installation 11
(B140-101X and B140-1A1-WP extender kits only)
Standard Extender/Splitter Installation 14
Extender/Splitter with Remote/Repeater Installation 17
(B140-1A0 and B140-1A0-WP-1 remote receiver units only)
Extender/Splitter Daisy-Chain Installation 20
Extender/Splitter Daisy-Chain with Remote/Repeater Installation 22
(B140-004 extender/splitter, and B140-1A0 and B140-1A0-WP
remote receivers only)
Warranty & Warranty Registration 27
201110026-93-3094-EN.indd 1 11/3/2011 11:37:06 AM
2
Package Contents
Product Features
B140-101
B140-1P1-WP-1
B140-101X
B140-1A1-WP
B140-002
B140-004
B140-1A0
B140-1A0-WP-1
B140-1P0
B140-1P0-WP-1
B140-110
Local Unit (L), Remote Unit
(R), or Both (B)
B B B B L L R R R R R
External Power Supplies
(0, 1, or 2)
0 0 1 2 1 1 1 1 0 0 1
Mounting Hardware X X X X X
Wallplate Screws X X X X
Screwdriver for Equalization
Adjustment
X X X X X
DVI Daisy-chain Cable X
All
• SupportDVI-DSingle-Linkvideoresolutionsupto1920x1080(60Hz)
• Plug-and-play;nosoftwareordriversrequired
• Compatiblewithallmajoroperatingsystems
•HDCPcompatible
B140-101
• DVIoverCat5PassiveExtenderKit(Box-style)
• Extenda1024x768(60Hz)signalupto100ft.fromthesource,or
a1920x1080(60Hz)signalupto50ft.fromthesource
• Noexternalpowerrequired
201110026-93-3094-EN.indd 2 11/3/2011 11:37:06 AM
3
Product Features
B140-1P1-WP-1
• DVIoverCat5PassiveExtenderWallplateKit
• Extenda1024x768(60Hz)signalupto75ft.fromthesource,ora
1920x1080(60Hz)signalupto50ft.fromthesource
• RJ45-stylewallplatesallowfortheuseofstandardCat5e/6patch
cables;110punchdownconnectionnotrequired
• Noexternalpowerrequired
B140-101X
• DVIoverCat5ActiveExtenderKit(Box-style)
• Extenda1024x768(60Hz)signalupto200ft.fromthesource,or
a1920x1080(60Hz)signalupto150ft.fromthesource
• Remotereceiverunitfeaturesabuilt-inEqualizationcontrolforvideo
image adjustment
• Includesmountinghardwarethatallowsremoteunittobe
wallmounted, rackmounted or pole mounted
B140-1A1-WP
• DVIoverCat5ActiveExtenderWallplateKit
• Extenda1024x768(60Hz)signalupto200ft.fromthesource,or
a1920x1080(60Hz)signalupto150ft.fromthesource
• Remotereceiverunitfeaturesabuilt-inEqualizationcontrolforvideo
image adjustment
• RJ45-stylewallplatesallowfortheuseofstandardCat5e/6patch
cables;110punchdownconnectionnotrequired
201110026-93-3094-EN.indd 3 11/3/2011 11:37:06 AM
4
Product Features
B140-002
• 2-PortDVIoverCat5Extender/SplitterLocalTransmitterUnit
(Box-style)
• SplitsaDVI-DSingle-Linksignalinto2separatesignals
• Workswithremote/repeaterandreceiverunitstoextendaDVI-D
Single-Linksignalpassedthe16-ft.(5m.)distancelimitation
• Includesmountinghardwarethatallowstheunittobewallmounted,
rackmounted or pole mounted
B140-004
• 4-PortDVIoverCat5Extender/SplitterLocalTransmitterUnit
(Box-style)
• SplitsaDVI-DSingle-Linksignalinto4
• AdditionalDVIportcanbeusedtoconnectalocalmonitororto
daisy-chain additional B140-004 units. Up to 3 B140-004 units
can be daisy-chained together to increase the number of connected
monitors
• Workswithremote/repeaterandreceiverunitstoextendaDVI-D
Single-Linksignalpassedthe16ft.(5m.)distancelimitation
• Includesmountinghardwarethatallowstheunittobewallmounted,
rackmounted or pole mounted
• Upto3B126-004unitscanbemountedinaB132-004-RB
1U rackmount bracket
201110026-93-3094-EN.indd 4 11/3/2011 11:37:06 AM
5
Product Features
B140-1A0
• DVIoverCat5ActiveExtenderRemoteReceiverUnit(Box-style)
• WorkswithB140-002andB140-004extender/splitterstoextenda
1024x768(60Hz)signalupto200ft.fromthesource,ora
1920x1080(60Hz)signalupto150ft.fromthesource
• Built-inEqualizationcontrolforvideoimageadjustment
• Includesmountinghardwarethatallowstheunittobewallmounted,
rackmounted or pole mounted
B140-1A0-WP-1
• DVIoverCat5ActiveExtenderWallplate
• WorkswithB140-002andB140-004extender/splitterstoextenda
1024x768(60Hz)signalupto200ft.fromthesource,ora
1920x1080(60Hz)signalupto150ft.fromthesource
• Built-inEqualizationcontrolforvideoimageadjustment
• RJ45-stylewallplateallowsfortheuseofstandardCat5e/6patch
cables;110punchdownconnectionnotrequired
B140-1P0
• DVIoverCat5PassiveExtenderRemoteReceiverUnit(Box-style)
• WorkswithB140-002andB140-004extender/splitterstoextenda
1024x768(60Hz)signalupto100ft.fromthesource,ora
1920x1080(60Hz)signalupto50ft.fromthesource
• Built-inDVIcable;separateDVIcablenotrequired
• Noexternalpowerrequired
201110026-93-3094-EN.indd 5 11/3/2011 11:37:06 AM
6
Product Features
B140-1P0-WP-1
• DVIoverCat5PassiveExtenderWallplate
• WorkswithB140-002andB140-004extender/splitterstoextenda
1024x768(60Hz)signalupto75ft.fromthesource,ora1920x
1080(60Hz)signalupto50ft.fromthesource
• RJ45-stylewallplateallowsfortheuseofstandardCat5e/6patch
cables;110punchdownconnectionnotrequired.
• Noexternalpowerrequired
B140-110
• DVIoverCat5ExtenderRemote/RepeaterUnit(Box-style)
• ExtendsandexpandsyourTrippLiteDVIoverCat5installation,
allowing you to locate multiple monitors at different points in a chain
of up to 700 ft.
• Extendsa1024x768(60Hz)signalupto175ft.,ora1920x1080
(60Hz)signalupto125ft.fromthelocaltransmitterunittotherst
remote/repeater unit in the installation
• Extendsa1024x768(60Hz)signaluptoanadditional175ft.,or
a1920x1080(60Hz)signaluptoanadditional125ft.fromeach
remote/repeater unit to the next unit in the chain. In a full 4-level
daisychaininstallation,a1024x768(60Hz)signalcanbeextended
upto700ft.,ora1920x1080(60Hz)signalupto500ft.fromthe
source to the last remote unit in the chain.
• Connectupto4remoteunits(3remote/repeatersand1receiver),
with a monitor located at each point in the chain
• Built-inEqualizationcontrolforvideoimageadjustment
• Includesmountinghardwarethatallowstheunittobewallmounted,
rackmounted or pole mounted
201110026-93-3094-EN.indd 6 11/3/2011 11:37:06 AM
7
Product Features
Optional Accessories:
• B132-004-RB1URackmountBracket
• N202-SeriesCat624AWG,solidwirepatchcables
• P561-SeriesDVI-DSingle-Linkcables
201110026-93-3094-EN.indd 7 11/3/2011 11:37:06 AM
8
Mounting (Optional)
The B140-101X, B140-002, B140-004, B140-1A0 and B140-110
come with mounting hardware that allows them to be mounted in
a variety of ways. The following images show the different ways the
included mounting brackets can be attached for different mounting
methods. Note: The B140-004 can also be mounted to a Tripp Lite
B132-004-RB 1U Rackmount Bracket. Up to 3 B140-004 local units
can be connected to a B132-004-RB.
Wallmount
19” Rackmount Pole Mount
201110026-93-3094-EN.indd 8 11/3/2011 11:37:08 AM
TO DVI SOURCE
RJ45 JACK
Cat5/5e/6
PATCH CABLE
LOCAL UNIT
POWER
JACK
REMOTE UNIT
TO DVI MONITOR
B140-101 — Up to 100 ft. at 1024 x 768 (60 Hz), or up to 50 ft. at 1920 x 1080 (60 Hz)
B140-1P1-WP-1 — Up to 75 ft. at 1024 x 768 (60 Hz), or up to 50 ft. at 1920 x 1080 (60 Hz)
B140-101X and B140-1A1-WP — Up to 200 ft. at 1024 x 768 (60 Hz), or up to 150 ft. at 1920 x 1080 (60 Hz)
9
Standard Extender Kit Installation
(B140-101, B140-1P1-WP-1, B140-101X, B140-1A1-WP)
Notes:
1. The diagram below shows a B140-101X installation. Installation will
be the same for the B140-1A1-WP. Installation will be similar for the
B140-101 and B140-1P1-WP-1, except that they will not require
external power.
2. Test to make sure that the entire installation works properly before
pulling cables through ceilings/walls.
3. To achieve maximum distance and performance, use 24 AWG Solid
Wire Cat5e/6 cable. Using stranded wire cable, or cable with a gauge
(AWG) size higher than 24 AWG, will result in lesser performance
and shorter extension distance. Tripp Lite N202-Series (Cat6) patch
cables are made with 24 AWG Solid Wire cabling.
1
Make sure power to the DVI source is turned off.
2
Connect the built-in DVI connector on the B140-101 or B140-101X
local unit to the DVI source, or connect the B140-1A1-WP or
B140-1P1-WP-1 local unit to the source using a Tripp Lite
P561-SeriesDVIcable.
201110026-93-3094-EN.indd 9 11/3/2011 11:37:08 AM
10
Standard Extender Kit Installation
3
B140-1A1-WP only: Connect the external power supply to the local
unit and plug it into a Trip Lite Surge Suppressor, Power Distribution
Unit(PDU),orUninterruptablePowerSupply(UPS).TheGreen
Power LED will illuminate.
4
ConnecttheRJ45portsonthelocalandremoteunitsusing
Cat5e/6cable.
5
Connect the built-in DVI connector on the B140-101 remote unit to
the DVI monitor, or connect the B140-1A1-WP, B140-1P1-WP-1 or
B140-101X remote unit to the monitor using a Tripp Lite
P561-SeriesDVIcable.
6
B140-1A1-WP and B140-101X only: Connect the external
power supply to the remote unit and plug it into a Tripp Lite Surge
Suppressor, Power Distribution Unit (PDU) or Uninterruptible Power
Supply(UPS).TheGreenRJ45LEDontheB140-101Xremoteunit
willilluminatetoindicateitisreceivingpower.TheGreenPowerLED
will illuminate on the B140-1A1-WP remote unit.
7
TurnonthepowertotheDVIsource.TheGreenRJ45LEDswill
illuminate on the B140-101 and B140-101X units, and the Power
LEDs will illuminate on the B140-1P1-WP-1 units to indicate that
theyarereceivingpower.TheOrangeRJ45LEDwillilluminateonthe
B140-101X remote unit to indicate it is receiving a signal from the
source. The Orange Activity LEDs will illuminate on the
B140-1A1-WP units.
8
B140-1A1-WP and B140-101X only: If necessary, adjust the
Equalization control on the remote unit to improve the video image.
Note: An improper Equalization setting can cause the monitor not
to display a picture at all. Try each Equalization setting until an
acceptable image is displayed.
201110026-93-3094-EN.indd 10 11/3/2011 11:37:09 AM
DVI SOURCE
B140-1A1-WP LOCAL
TRANSMITTER
B140-1A1-WP REMOTE
RECEIVER
B140-110
REMOTE
REPEATER
B140-110
REMOTE
REPEATER
B140-110
REMOTE
REPEATER
Up to 175 ft. at 1024 x 768 (60Hz)
Up to 125 ft. at 1920 x 1080 (60Hz)
Up to 175 ft. at 1024 x 768 (60Hz)
Up to 125 ft. at 1920 x 1080 (60Hz)
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
11
Extender Kit with Remote/Repeater
Installation (B140-101X and B140-1A1-WP extender kits only)
Notes:
1. Test to make sure the entire installation works properly before pulling
cables through ceilings/walls.
2. To achieve maximum distance and performance, use 24 AWG solid
wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable
with a gauge (AWG) size higher than 24 AWG, will result in shorter
extension distance. All Tripp Lite N202-Series Cat6 cables are made
with 24 AWG solid wire cabling.
3. The installation diagram shows a B140-1A1-WP. The B140-101X
installation is the same, except its local unit does not require power.
1
Make sure the DVI source is powered OFF.
2
Connect the built-in DVI connector on the B140-101X local unit to
theDVIsource;or,connecttheDVIsourcetotheINPUTportonthe
B140-1A1-WPlocalunitusingaTrippLiteP561-SeriesDVI-DSingle
Link Cable.
3
B140-1A1-WP only: Connect the external power supply to the local
unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The
GreenPowerLEDwillilluminate.
201110026-93-3094-EN.indd 11 11/3/2011 11:37:09 AM
12
4
UsingCat5e/6cable,connecttheRJ45portonthelocalunittothe
RJ45INPUTportontheB140-110remote/repeaterunit.
5
Connect a monitor to the DVI OUTPUT port on the remote/repeater
unitusingaTrippLiteP561-SeriesDVI-DSingle-LinkCable.
6
Connect the external power supply to the remote/repeater unit and
plugitintoaTrippLiteSurgeSuppressor,PDUorUPS.TheGreen
PowerLEDandtheGreenRJ45LEDsilluminatetoindicatetheunit
is receiving power.
Up to 4 units can be daisy-chained (3 remote/repeaters and 1 receiver).
Toconnectadditionalremote/repeaterunits,proceedtostep7.Tonish
your installation with the B140-101X or B140-1A1-WP remote receiver
unit, proceed to step 11.
7
UsingCat5e/6cable,connecttheRJ45OUTPUTportontherst
remote/repeaterunittotheRJ45INPUTportonasecondremote/
repeater unit.
8
Connect a monitor to the DVI OUTPUT port on the remote/repeater
unitthatyoujustaddedusingaTrippLiteP561-SeriesDVI-D
Single-Link Cable.
9
Connect the external power supply to the remote/repeater unit and
plugitintoaTrippLiteSurgeSuppressor,PDUorUPS.TheGreen
PowerLEDandtheGreenRJ45LEDsilluminatetoindicatetheunit
is receiving power.
10
To add a third remote/repeater unit, repeat steps 7 through 9.
TonishyourinstallationwiththeB140-101XorB140-1A1-WP
remote receiver unit, proceed to step 11.
Extender Kit with Remote/Repeater
Installation (B140-101X and B140-1A1-WP extender kits only)
201110026-93-3094-EN.indd 12 11/3/2011 11:37:09 AM
13
11
UsingCat5e/6cable,connecttheRJ45OUTPUTportonthelast
remote/repeaterunittotheRJ45INPUTportoftheB140-101Xor
B140-1A1-WP remote receiver unit.
12
Connect a monitor to the DVI OUTPUT port on the remote receiver
unitusingaTrippLiteP561-SeriesDVI-DSingle-LinkCable.
13
Connect the external power supply to the remote receiver unit and
plugitintoaTrippLiteSurgeSuppressor,PDUorUPS.TheGreen
RJ45LEDontheB140-101Xremotereceiver,ortheGreenPower
LED on the B140-1A1-WP remote wallplate, illuminates to indicate
the unit is receiving power from the external power supply.
14
Turn on the power to the DVI source. The Orange LEDs on the
B140-1A1-WP units illuminate to indicate a signal is being received
fromthesource.TheOrangeRJ45LEDsontheB140-101Xand
B140-110 units illuminates to indicate a signal is being received
from the source.
15
If necessary, use the Equalization control on the remote/repeater
unit(s) and remote receiver unit to adjust the video image. Note: An
improper Equalization setting can cause the monitor not to display
a picture at all. Try each Equalization setting until an acceptable
picture is displayed.
Extender Kit with Remote/Repeater
Installation (B140-101X and B140-1A1-WP extender kits only)
201110026-93-3094-EN.indd 13 11/3/2011 11:37:09 AM
B140-004
B140-1A0
B140-1P0
B140-1A0-WP-1
Up to 200 ft. at 1024 x 768 (60Hz)
Up to 150 ft. at 1920 x 1080 (60Hz)
Up to 100 ft. at 1024 x 768 (60Hz)
Up to 50 ft. at 1920 x 1080 (60Hz)
Up to 75 ft. at 1024 x 768 (60Hz)
Up to 50 ft. at 1920 x 1080 (60Hz)
DVI OVER Cat5
EXTENDER
REMOTE UNIT
MODEL: B140-1P0
B140-1P0-WP-1
14
Standard Extender/Splitter Installation
Notes:
1. The diagram below shows a B140-004 installation. Installation will
be the same when using a B140-002, except that the B140-002
has fewer RJ45 ports and no local monitor port.
2. Test to make sure that the entire installation works properly before
pulling cables through ceilings/walls.
3. To achieve maximum distance and performance, use 24 AWG solid
wire Cat5e/6 cable. Using stranded wire cable, or cable with a gauge
(AWG) size higher than 24 AWG, will result in lesser performance
and shorter extension distance. Tripp Lite N202-Series (Cat6) patch
cables are made with 24 AWG solid wire cabling.
201110026-93-3094-EN.indd 14 11/3/2011 11:37:10 AM
15
Standard Extender/Splitter Installation
1
Make sure the DVI source is powered OFF.
2
Connect the DVI source to the DVI port on the B140-002 or
B140-004labeledINPUTusingaTrippLiteP561-SeriesDVI-D
Single-Link Cable.
3
Optional for B140-004: Connect a DVI monitor to the DVI port on
theB140-004markedLOCALusingaTrippLiteP561-SeriesDVI-D
Single-Link Cable.
4
Connect the external power supply to the B140-002 or B140-004
local unit and plug it into a Tripp Lite Surge Suppressor, PDU or
UPS.TheGreenRJ45LEDsandRedPowerLEDontheB140-004
will illuminate to indicate power is being received from the external
powersupply.TheGreenRJ45LEDsontheB140-002willilluminate
to indicate power is being received from the external power supply.
5
UsingCat5e/6cable,connectoneoftheRJ45outputportsonthe
localunittotheRJ45inputportontheB140-1P0,B140-1A0,
B140-1P0-WP-1 or B140-1A0-WP-1 remote unit.
6
Repeatstep5foreachadditionalremoteunityouareconnecting.
7
B140-1A0 and B140-1A0-WP-1 only: Connect the external
power supply to the B140-1A0 or B140-1A0-WP-1 and plug it into
aTrippLiteSurgeSuppressor,PDUorUPS.TheGreenRJ45LED
ontheB140-1A0andtheGreenLEDontheB140-1A0-WP-1will
illuminate to indicate that the unit is receiving power.
8
Repeat step 7 for each additional B140-1A0 or B140-1A0-WP-1 in
the installation.
201110026-93-3094-EN.indd 15 11/3/2011 11:37:10 AM
16
9
ConnecttheB140-1P0DVI-DSingle-Linkconnectortothemonitor;
or, connect the B140-1P0-WP-1, B140-1A0 or B140-1A0-WP-1 to
themonitorusingaTrippLiteP561-SeriesDVI-DSingle-LinkCable.
TheGreenRJ45LEDontheB140-1P0andtheGreenLEDonthe
B140-1P0-WP-1 illuminate to indicate the unit is receiving power
from the monitor.
10
Repeat step 9 for each additional monitor you are connecting.
11
TurnonthepowertotheDVIsource.TheOrangeRJ45LEDs
illuminate on the B140-002, B140-004 and B140-1A0, and the
Orange LED illuminates on the B140-1A0-WP-1 to indicate the unit
is receiving a signal from the source. The image should now be
displayed on the connected monitors.
12
If necessary, use the Equalization control on the B140-1A0 or
B140-1A0-WP-1 to adjust the video image. Note: An improper
Equalization setting can cause the monitor not to display a picture
at all. Try each Equalization setting until an acceptable image is
displayed.
Standard Extender/Splitter Installation
201110026-93-3094-EN.indd 16 11/3/2011 11:37:10 AM
OPTIONAL LOCAL
MONITOR
B140-004 LOCAL
TRANSMITTER
B140-110 REMOTE/
REPEATER
B140-110 REMOTE/
REPEATER
B140-110 REMOTE/
REPEATER
Up to 175 ft. at 1024 x 768 (60Hz)
Up to 125 ft. at 1920 x 1080 (60Hz)
Up to 175 ft. at 1024 x 768 (60Hz)
Up to 125 ft. at 1920 x 1080 (60Hz)
DVI SOURCE
B140-110 REMOTE/
REPEATER
B140-110 REMOTE/
REPEATER
B140-110 REMOTE/
REPEATER
B140-110 REMOTE/
REPEATER
B140-110 REMOTE/
REPEATER
B140-110 REMOTE/
REPEATER
B140-1A0-WP-1
REMOTE RECEIVER
B126-1A0-WP-1
REMOTE RECEIVER
B126-1A0
REMOTE RECEIVER
B140-110 REMOTE/
REPEATER
B140-110 REMOTE/
REPEATER
B140-110 REMOTE/
REPEATER
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
B126-1A0
REMOTE RECEIVER
17
Notes:
1. Test to make sure the entire installation works properly before pulling
cables through ceilings/walls.
2. To achieve maximum distance and performance, use 24 AWG solid
wire Cat5e/6 cable. Using stranded wire Cat5e/6 cable, or cable
with a gauge (AWG) size higher than 24 AWG, will result in shorter
extension distance. All Tripp Lite N202-Series Cat6 cables are made
with 24 AWG solid wire cabling.
3. The installation diagram shows the B140-004. The B140-002
installation will be the same, except there are only 2 remote ports
and there is no local monitor port.
Extender/Splitter with Remote/Repeater Installation
(B140-1A0 and B140-1A0-WP-1 remote receiver units only)
1
Make sure the DVI source is powered OFF.
201110026-93-3094-EN.indd 17 11/3/2011 11:37:12 AM
18
Extender/Splitter with Remote/Repeater Installation
(B140-1A0 and B140-1A0-WP-1 remote receiver units only)
2
ConnecttheDVIsourcetotheINPUTportontheB140-002or
B140-004usingaTrippLiteP561-SeriesDVI-DSingle-LinkCable.
3
Optional for B140-004: Connect a local monitor to the DVI
OUTPUTportusingaTrippLiteP561-SeriesDVI-DSingle-LinkCable.
4
Connect the external power supply to the local unit and plug it into
aTrippLiteSurgeSuppressor,PDUorUPS.TheGreenRJ45LEDs
illuminate to indicate power is being received from the external
power supply. An additional Red LED on the B140-004 also
illuminates to indicate that power is being received.
5
UsingCat5e/6cable,connectoneoftheRJ45outputportsonthe
localunittotheRJ45inputportontheB140-110remote/repeater
unit.
6
Connect a monitor to the DVI OUTPUT port on the remote/repeater
unitusingaTrippLiteP561-SeriesDVI-DSingle-LinkCable.
7
Connect the external power supply to the remote/repeater unit and
plugitintoaTrippLiteSurgeSuppressor,PDUorUPS.TheGreen
PowerLEDandtheGreenRJ45LEDsilluminatetoindicatetheunit
is receiving power.
Up to 4 units can be daisy-chained (3 remote/repeaters and 1 receiver).
Toconnectadditionalremote/repeaterunits,proceedtostep8.Tonish
your installation with a B140-1A0 or B140-1A0-WP-1 remote receiver
unit, proceed to step 12.
8
UsingCat5e/6cable,connecttheRJ45OUTPUTportontherst
remote/repeaterunittotheRJ45INPUTportonasecondremote/
repeater unit.
9
Connect a monitor to the DVI OUTPUT port on the remote/repeater
unitthatyoujustaddedusingaTrippLiteP561-SeriesDVI-DSingle-
Link Cable.
201110026-93-3094-EN.indd 18 11/3/2011 11:37:12 AM
19
Extender/Splitter with Remote/Repeater Installation
(B140-1A0 and B140-1A0-WP-1 remote receiver units only)
10
Connect the external power supply to the remote/repeater unit and
plugitintoaTrippLiteSurgeSuppressor,PDUorUPS.TheGreen
PowerLEDandtheGreenRJ45LEDsilluminatetoindicatetheunit
is receiving power.
11
To add a third remote/repeater unit, repeat steps 8 through 10. To
nishyourinstallationwithaB140-1A0orB140-1A0-WP-1remote
receiver unit, proceed to step 12.
12
UsingCat5e/6cable,connecttheRJ45OUTPUTportonthelast
remote/repeaterunittotheRJ45INPUTportonaB140-1A0or
B140-1A0-WP-1 remote receiver unit.
13
Connect a monitor to the DVI OUTPUT port on the remote receiver
unitusingaTrippLiteP561-SeriesDVI-DSingle-LinkCable.
14
Connect the external power supply to the remote receiver unit and
plugitintoaTrippLiteSurgeSuppressor,PDUorUPS.TheGreen
RJ45LEDsontheB140-1A0andtheGreenLEDontheB140-1A0-
WP-1 illuminate to indicate that the unit is receiving power.
15
Repeatsteps5through14foreachadditionalRJ45outputporton
the local transmitter unit.
16
TurnonthepowertotheDVIsource.TheOrangeRJ45LEDson
the local transmitter, remote/repeater and B140-1A0 illuminate
to indicate a signal is being received from the source. The Orange
LED on the B140-1A0-WP-1 illuminates to indicate a signal is being
received from the source.
17
If necessary, use the Equalization control on the remote/repeater
unit(s) and remote receiver unit to adjust the video image. Note: An
improper Equalization setting can cause the monitor not to display
a picture at all. Try each Equalization setting until an acceptable
picture is displayed.
201110026-93-3094-EN.indd 19 11/3/2011 11:37:12 AM
Level 1
Level 2
Level 3
OPTIONAL LOCAL
MONITOR
B140-1P0 — Up to 100 ft. at 1024 x 768 (60 Hz), or up to 50 ft. at 1920 x 1080 (60 Hz)
B140-1P0-WP-1 — Up to 75 ft. at 1024 x 768 (60 Hz), or up to 50 ft. at 1920 x 1080 (60 Hz)
B140-1A0 and B140-1A0-WP-1 — Up to 200 ft. at 1024 x 768 (60 Hz), or up to 150 ft. at 1920 x 1080 (60 Hz)
20
Extender/Splitter Daisy-Chain Installation
(B140-004 only)
Notes:
1. Test to make sure that the entire installation works properly before
pulling cables through ceilings/walls.
2. To achieve maximum distance and performance, use 24 AWG solid
wire Cat5e/6 cable. Using stranded wire cable, or cable with a gauge
(AWG) size higher than 24 AWG, will result in lesser performance
and shorter extension distance. Tripp Lite N202-Series (Cat6) patch
cables are made with 24 AWG solid wire cabling.
201110026-93-3094-EN.indd 20 11/3/2011 11:37:13 AM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Tripp Lite B140-004 Owner's manual

B140-004
Tripp Lite
Brand
Tripp Lite
Model
B140-004
Category
AV extenders
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents