Craftsman 13953904D Owner's manual

Brand: Craftsman

Model: 13953904D

Category: Garage Door Opener

Type: Owner's manual

Owner'sManual/ManualDelPr0pietari0

CRAFTSMAN°

112 HP

315MHz GARAGE DOOR OPENER

ABRIDOR DE PUERTA DE COCHERA

For Residential Use Only/Solo para uso residencial

Model/Modelo • 139.53904D

DE 315MHz

I"11

Read and follow all safety rules and

operating instructions before first use

of this product.

Fasten the manual near the garage

door after installation.

Periodic checks of the opener are

required to ensure safe operation.

Leer y seguir todas las reglas de

seguridad y las instrucciones de

operacion antes de usar este producto

por primera vez.

Guardar este manual cerca de la

puerta de la cochera.

Se deben realizar revisiones

periodicas del abridor de puertas para

asegurar su operacion segura.

0Qus

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A

www.sears.com/craftsman

TABLE OF CONTENTS

INTRODUCTION 2- 7

Safetysymbol and signal word review .......................................2

Preparing your garagedoor........................................................ 3

Tools needed..............................................................................3

Planning ..................................................................................4-5

Carton inventory .........................................................................6

Hardware inventory.....................................................................7

ASSEMBLY 8-11

Assemblethe rail and install the trolley......................................8

Fastenthe rail to the motor unit and

Install the idler pulley..................................................................9

Install the belt and attachthe belt cap retainer.........................10

Setthe tension..........................................................................11

INSTALLATION 11-26

Installation safetyinstructions ..................................................11

Determinethe headerbracket location .....................................12

Install the headerbracket.......................................................... 13

Attach the rail to the headerbracket.........................................14

Position the opener...................................................................15

Hangthe opener .......................................................................16

Install the door control .............................................................17

Install the lights ........................................................................18

Attach the emergencyreleaserope and handle........................ 18

Electrical requirements.............................................................19

Install The Protector System®..............................................20-22

Fastenthe door bracket.......................................................23-24

Connectthe door arm to thetrolley .....................................25-26

ADJUSTMENT 27-29

Adjust thetravel limits ..............................................................27

Adjust theforce ........................................................................28

Testthe safety reversalsystem.................................................29

TestThe Protector System®...................................................... 29

OPERATION 30-34

Operationsafety instructions ....................................................30

Using your garagedoor opener................................................ 30

Using the wall-mounted Door Control...................................... 31

To open the door manually.......................................................31

Careofyour garagedoor opener..............................................32

Having a problem?....................................................................33

Diagnostic chart........................................................................34

PROGRAMMING 35-36

To add or reprograma hand-held remote control .................... 35

To eraseall codes.....................................................................35

3-Function Remotes..................................................................35

To add, reprogram or changea KeylessEntry PIN...................36

REPAIRPARTS 37-38

Rail assembly parts ..................................................................37

Installation parts .......................................................................37

Motor unit assembly parts........................................................ 38

ACCESSORIES 39

WARRANTY 39

REPAIRPARTS& SERVICE BACKCOVER

INTRODUCTION

Safely Symboland SignalWordReview

This garage door opener has beendesignedand tested to offer safe serviceprovided it is installed, operated,maintained and tested in

strict accordancewith the instructions and warnings contained in this manual.

Mechanical

Electrical

Whenyou seethese SafetySymbols and Signal Words on the

following pages,they will alertyou to the possibility of serious

injury or deathif you do not comply with the warnings that

accompanythem. Thehazardmay come from something

mechanicalor from electric shock. Readthe warnings carefully.

Whenyou seethis Signal Word on the following pages, it will

alertyou to the possibility of damageto your garagedoor and/or

the garagedoor opener if you do not comply with the cautionary

statements that accompany it. Readthem carefully.

Preparingyourgaragedoor

Beforeyou begin:

* Disablelocks.

* Removeany ropes connectedto garage door.

° Complete the following test to make sureyour garage door is

balancedand is not sticking or binding:

1. Lift the door about halfwayas shown. Releasethe door. If

balanced, it should stay in place,supported entirely by its

springs.

2. Raiseand lower the door to seeif there is any binding or

sticking.

If your door binds, sticks, or is out of balance,call a trained door

systems technician.

To prevent possible SERIOUSINJURYor DEATH:

° ALWAYScall atrained door systems technician if garage

door binds, sticks or is out of balance.An unbalanced

garagedoor may not reversewhen required.

° NEVERtry to loosen, move or adjust garagedoor, door

springs, cables,pulleys, brackets or their hardware,ALL of

which are under EXTREMEtension.

° DisableALL locks and removeALL ropes connectedto

garagedoor BEFOREinstalling and operating garagedoor

opener to avoidentanglement.

To prevent damageto garage door and opener:

° ALWAYSdisable locks BEFOREinstalling and operatingthe

opener.

° ONLYoperate garagedoor openerat 120V, 60 Hzto avoid

malfunction and damage.

SectionalDoor

One-Piece Door

Tools needed

During assembly, installation and adjustment of the opener,

instructions will call for handtools as illustrated below.

Stepladder

Level (optional)

Pencil

Tape Measure

Dr_ Wire Cutters

Drill 3/16", 5/16"

_0 and 5/32"

1/2", 5/8", 7/16", 9/16" Pliers

and 1/4"

Hack Saw

Claw Hammer

Screwdriver

Adjustable End Wrench

P_nnmg

Identify the type and height of your garagedoor. Surveyyour

garageareato see if any of the conditions below apply to your

installation. Additional materials may be required.You may find it

helpful to referback to this pageand the accompanying

illustrations asyou proceedwith the installation of your opener.

Dependingon your requirements,there are several installation

steps which may call for materialsor hardware not included in

the carton.

• Installation Step 1 - Lookat the wall or ceiling abovethe

garagedoor. Theheader bracketmust be securelyfastenedto

structural supports.

• Installation Step 5 - Doyou havea finished ceiling in your

garage? If so, a support bracket and additionalfastening

hardware may be required.

• Installation Step 10 - Dependingupon garageconstruction,

extension brackets or wood blocks may be neededto install

sensors

• Installation Step 10 - Alternatefloor mounting of the safety

reversingsensor will require hardwarenot provided.

• Doyou havean access door in addition to the garagedoor? If

not, Model 53702 EmergencyKeyReleaseis required.See

Accessoriespage.

• Lookat the garage door where it meetsthe floor. Any gap

betweenthe floor and the bottom of the door must not exceed

1/4" (6 mm). Otherwise,the safetyreversalsystem maynot

work properly. SeeAdjustment Step 3. Floor or door should be

repaired.

SECTIONALDOORINSTALLATIONS

• Doyou havea steel, aluminum, fiberglass or glass panel door?

If so, horizontal and vertical reinforcement is required

(Installation Step 11).

• Theopener should be installed abovethe center of the door. If

there is a torsion spring or center bearing plate in the way of

the header bracket, it may be installed within 4 feet (1.22 m)

to the left or right of the door center. See Installation Steps 1

and 11.

• If your door is morethan 7 feet (2.13 m) high, see rail

extension kits listed on Accessoriespage.

SectionalDoor Installation

Horizontal and vertical reinforcement

is needed for lightweight garage doors

(fiberglass, steel, aluminum, door with

glass panels, etc.). See page 23 for details.

Header Wail

Rail

Extension Spring

FINISHED CEILING

Support bracket &

fastening hardware

is required.

See page 16.

,tor unit

Wall-

mounted [

Door Access Door

Control

Safety Reversing Sensor

Gap between floor

and bottom of door

must not exceed 1/4" (6 mm).

Safety

Reversing

Sensor

CLOSED POSITION

Header

Bracket Trolley

/ Stop Bolt Trolley

_ Garage ...... .....

F///,_ Door 'c_/ --I Belt

_////4 Spring I

__ _/Str"a?ht L Emergency Release

_/ Arm i_ Rope&Handle

I _ _ Curved

Header _ _ Door

Wall Ix\/I \ Arm

Garage HI £oo:

oooJ-1-lJ _ek_

Planning(Continued)

ONE-PIECEDOORINSTALLATIONS

• Generally,a one-piecedoor does not require reinforcement. If

your door is lightweight, refer to the information relatingto

sectional doors in Installation Step 11.

• Dependingon your door's construction, you may need

additional mounting hardwarefor the door bracket (Step 11).

Without a properly working safety reversal system, persons

(particularly small children) could be SERIOUSLYINJUREDor

KILLEDby a closing garagedoor.

• Thegap betweenthe bottom of the garage door and the

floor MUST NOTexceed1/4" (6 mm). Otherwise,the safety

reversalsystem may not work properly.

• Thefloor or the garage door MUSTbe repairedto eliminate

the gap.

ONE-PIECEDOORWITHOUTTRACK

FINISHED CEILING

Support bra(

& fastening

hardware is required.

See page 16.

rdf'l I

Safety Reversing Sensor

Header Wall

Rail

Access

Door

Safety Reversing

Gap between floor Sensor

Wall-mounted

Door Control

and bottom of door must not exceed 1/4" (6 ram).

Motor Unit

eader

,'all

CLOSED POSITION

Trolley Stop Bolt

Belt Trolley

Straight Door

Door

Arm

-- Garage

Door

Emergency

Release

Rope & Handle

ONE-PIECEDOORWITHTRACK

Jl__ Gapbteween floor Sensor

_._v .-\ and bottom of door

Safety

must not exceed 1/4" (6 mm).

Reversing Sensor

CLOSED POSITION

Trolley Stop Bolt Belt Trolley

Door

Bracket

Garage

Door

Straight

Door

Arm

Rail

Release

Rope &

Handle

CartonInventory

Your garagedoor opener is packagedin one carton which

contains the motor unit and all parts illustrated below.

Accessorieswill depend on the model purchased.If anything is

missing, carefully check the packing material. Parts may be stuck

in the foam. Hardwarefor assemblyand installation is shown on

the next page.Savethe carton and packing material until

installation and adjustment is complete.

Door Control Button

SECURITY÷*_

3-Function Remote Control (1)

Belt Cap Retainer

Trolley

MotorUnitwith 2 LightLenses

IdlerPulley

Rail

Fron! (header) /_#/

Header Bracket

Rail

Center/Back

Sections

Belt

Door Bracket

CurvedDoor

ArmSection

Hanging Brackets

Safety Reversing

Sensor Bracket (2)

The Protector System®

(2) Safety Reversing Sensors

(1 Sending Eyeand 1 Receiving Eye)

with 2-Conductor White & White/Black

Bell Wire attached

2-Conductor BellWire

White & White/Red

Safety Labels

and

Literature

Straight Door

Arm Section

HardwareInventory

Separateall hardwareand group as shown below for the assembly and installation procedures.

ASSEMBLYHARDWARE

Spring/Trolley Nut (1) Lock Nut Lock Washer Nut

1/4"-20 (2) 3/8" (1) 3/B" (1)

Bolt 1/4"-20xl-3/4" (2)

Trolley Threaded Shaft (1)

Master

Link (2)

Idler Bolt (1)

iNSTALLATiONHARDWARE

Carriage Bolt Wing Nut Ring

1/4"-20x1/B" (2) 1/4"-20 (2) Fastener (3)

Lag Screw

5/16"-9xl-5/8" (2)

Lag Screw

5/16"-18xl-7/8" (2)

Hex Bolt

5/16"-18x7/8" (4)

Nut 5/16"-18 (4)

Screw

6ABx1-1/4" (2)

LockWasher 5/16" (5)

Self-Threading Screw

1/4"-14x5/8" (2)

Handle

Insulated

Staples (30)

Screw 6-3Bx1" (2)

Drywall Anchors (2)

Clevis Pin Clevis Pin Clevis Pin

5/16"x1-1/2" (1) 5/16"x1" (1) 5/16"x1-1/4" (1)

Rope

ASSEMBLY STEP 1

Assemble the Raft & Install the Trolley

To avoidinstallationdifficulties,do notrunthe garagedoor

openeruntil instructedto do so.

To prevent INJURYfrom pinching, keephandsand fingers

away from the joints while assembling the rail.

Thefront rail has a cut out "window" at the door end (see

illustration). Thehole abovethis windowis larger onthe top of

the raft than on the bottom. A smaller hole 3-1/2" (8.9 cm) away

is close to the rail edge.Rotatethe back rail so it hasa similar

hole close to the oppositeedge,about 4-3/4" (12 cm) from the far

end.

1. Removethe straight door arm and hanging bracketpackaged

inside the front rail and set asidefor Installation Step5 and 12.

NOTE:Toprevent INJURYwhile unpacking therail carefully

remove the straight door arm stored within the rail section.

2. Align the rail sections on a flat surface asshown and slide the

taperedends into the larger ones. Tabs along the side will lock

into place.

3. Placethe motor unit on packing material to protect the cover,

and rest the back end of the rail on top. Forconvenience,put a

support under the front end of the rail.

4. As a temporary stop, insert a screwdriver into the hole

10"(25 cm) from the front end of the rail, as shown.

5. Checkto besure there are 4 plastic wear pads insidethe inner

trolley. If they becameloose during shipping, checkall packing

material. Snapthem back into position asshown.

6. Slide the trolley assembly along the rail from the back end to

the screwdriver.

Trolley

,ered

End

3ered

End

,ered

End

lack Rails

(TO MOTOR UNIT)

_..._rewd rive_,_

"_ /_/ Tabs

Window 0 ///

Cut-Out ', ///

\ _/.// FrontRail

Idler V_._ (TO DOOR)

Pulley

Hole _ ;

)ered

End

Inner Trolley

dar Pads

ASSEMBLY STEP 2

Fastenthe Rail to the MotorUnit

,, Inserta 1/4"-20xl-3/4" bolt into the cover protection bolt hole

on the back end of the rail as shown. Tighten securelywith a

1/4"-20 lock nut. DoNOT overtighten.

* Removethe two bolts from the top of the motor unit.

* Placethe "U" bracket,flat sidedown, on the motor unit and

align the bracketholes with the bolt holes. Fastenwith the

previously removed bolts.

* Align the rail assemblywith the top of the motor unit. Slide the

rail end onto the "U" bracket,all the way to the stops that

protrude on the top and sides of the bracket.

To avoid SERIOUSdamageto garagedoor opener, use ONLY

those bolts/fasteners mounted in the top of the opener.

"U" Bracket

Bolt

Bolts

Motor Unit

Sprocket

Cover

Protection

Bolt Hole

HARDWARESHOWNACTUALSIZE

Lock Nut

Bolt 1/4"-20xl-3/4" 1/4"-20

SLIDE RAIL TO STOPS

ONTOPAND SIDES

OFBRACKET

I Lock Nut

ASSEMBLY STEP 3

Install theIdler Pulley

* Laythe belt besidethe rail, as shown. Graspthe end with the

hookedtrolley connector and pass approximately 12" (30 cm)

of beltthrough the window. Keepthe ribbed side toward the

rail, and allow it to hang until Assembly Step 5.

* Removethe tapefrom the idler pulley. The inside center should

be pre-greased.If dry, regreaseto ensure proper operation.

* Placethe idler pulley into the window as shown.

* Insertthe idler bolt from the top through the rail and pulley.

Tighten with a 3/8" lock washer and nut underneaththe rail

until the lock washer is compressed.

* Rotatethe pulley to be sure it spins freely.

* Inserta 1/4"-20xl-3/4" bolt into the trolley stop holein the

front of the rail as shown. Tighten securely with a 1/4"-20 lock

nut.

Grease

_. _ __lnside

Pulley

_ _ Idler Pulley

Lock Washer 3/8"-_

Nut 3/8"

Trolley

Connector

Bolt

r _ Lock

Pulley , Nut

Idler Bolt

HARDWARESHOWNACTUALSIZE

Bolt 1/4"-20x1-3/4" Lock Nut 1/4"-20 Nut 3/8" Lock Washer 3/8"

ASSEMBLY STEP 4

Insta// the Be/t and Attach the Be/t Cap Retainer

1. Pull the belt around the idler pulleyand toward the trolley. The

ribbed side must contact thepulley.

2. Hookthe trolley connector into the retaining slot on the trolley

as shown.

3. With the trolley against the screwdriver, dispensethe

remainderof the belt along the rail length toward the motor

unit and around the sprocket. The sprocket teeth must engage

the belt.

4. Checkto make sure the belt is not twisted. Connectthe trolley

threadedshaft with the master link, as illustrated:

* Pushpins of master link bar through holes in end of belt

and trolley threadedshaft.

* Pushmaster link cap over pins and past pin notches.

. Slide clip-on spring over capand onto pin notchesuntil both

pins are securely locked in place.

5. Insertthe trolley threaded shaft through the hole in the trolley.

Besure the belt is not twisted.

6. Holdthe belt at the trolley shaft as you thread the spring nut by

hand onto the shaft until finger tight against the trolley. Do not

useany tools.

7. Removethe screwdriver.

8. Position the belt cap retainerover the motor unit sprocket as

shown and fasten to the mounting platewith 8x3/8" hex screws

provided.

To avoid possible SERIOUSINJURYto fingers from moving

garagedoor opener:

• ALWAYSkeephand clearof sprocket while operating

opener.

• Securely attachsprocket cover BEFOREoperating.

HARDWARESHOWNACTUALSIZE

Hex Screw 8x3/8"

Spring/Trolley Nut

Master Link

Clip-On Spring

Master LinkCap

Idler Pulley

Trolley

Connector

Retaining

Slot

Notch|

Trolley Master

Threaded Link Bar

Shaft

Hole

Hex Screws

Belt Cap_ #8x3/8"

Retainer _.,,,_, _ ,

Motor Unit

I Sprocket

Plate

ASSEMBLY STEP 5

Set the Tension

• Inserta screwdriver tip into one of the nut ring slots and brace

it firmly against the trolley.

• Placea 7/16" open end wrench on the squareend. Rotatethe

nut about 1/4 turn until the spring releasesand snaps the nut

ring against the trolley.

This sets the spring to optimum belt tension.

Youhave nowfinishedassemblingyourgaragedoor opener.

Please read thefollowingwarningsbeforeproceedingto the

installationsection.

Square

End

Trolley

Nut Ring

_1 _ BEFORE1" -_

(2.5 cm)

t_. AFTERRELEASE

1-1/4"

(3.18 cm)

INSTALLATION

IMPORTANTINSTALLATIONINSTRUCTIONS

To reducethe riskof SEVEREINJURYor DEATH:

1. READAND FOLLOWALL INSTALLATIONWARNINGSAND

INSTRUCTIONS.

2. Install garagedoor opener ONLYon properly balancedand

lubricated garagedoor. An improperly balanceddoor may

NOT reversewhen required and could result in SEVERE

INJURYor DEATH.

3. ALL repairsto cables,spring assemblies and other

hardware MUSTbe made by a trained door systems

technician BEFOREinstalling opener.

4. DisableALL locks and remove ALL ropes connectedto

garagedoor BEFOREinstalling openerto avoid

entanglement.

5. Install garagedoor opener 7 feet (2.13 m) or more above

floor.

6. Mount the emergency releasewithin reach, but at least

6 feet (1.8 m) abovethe floor and avoiding contact with

vehiclesto avoid accidentalrelease.

7. NEVERconnectgarage door opener to power source until

instructed to do so.

8. NEVERwear watches, rings or looseclothing while

installing or servicing opener.They could be caught in

garage door or opener mechanisms.

9. Install wall-mounted garage door control:

* within sight of the garage door.

* out of reachof children at minimum height of

5 feet (1.5 m).

* awayfrom ALL moving parts of the door.

10. Placeentrapmentwarning label on wall next to garagedoor

control.

11. Placemanual release/safetyreversetest label in plain view

on inside of garage door.

12. Upon completion of installation, test safety reversalsystem.

Door MUSTreverseon contact with a 1-1/2" (3.8 cm) high

object (or a 2x4 laid flat) on the floor.

INSTALLATION STEP 1

Determinethe HeaderBracketLocation

To prevent possible SERIOUSINJURYor DEATH:

* HeaderbracketMUST be RIGIDLYfastenedto structural

support on headerwall or ceiling, otherwise garagedoor

might not reversewhen required. DONOTinstall header

bracket over drywall.

. Concreteanchors MUST be usedif mounting headerbracket

or 2x4 into masonry.

. NEVERtry to loosen, move or adjust garagedoor, springs,

cables, pulleys,brackets, or their hardware,ALL of which

are under EXTREMEtension.

. ALWAYScall atrained door systems technician if garage

door binds, sticks, or is out of balance.An unbalanced

garagedoor might not reversewhen required.

Installation procedures vary according to garagedoor types.

Follow the instructions which applyto your door.

1. Closethe door and mark the insidevertical centerline of the

garagedoor.

2. Extendthe line onto the headerwall abovethe door.

Youcanfastentheheader bracketwithin 4 feet

(1.22 m) ofthe left or right ofthe doorcenteronly if a

torsionspringor center bearingplate is in the way;or you

canattachit tothe ceiling (see page 13) whenclearanceis

minimal. (It may be mountedon thewall upsidedownif

necessary,to gainapproximately1/2" (1 cm).)

If you need to install the headerbracket on a 2x4 (on wall or

ceiling), use lag screws (not provided) to securely fastenthe

2x4 to structural supports asshown here and on page 13.

3. Openyour door to the highest point of travel asshown. Draw

an intersecting horizontal line on the headerwall abovethe

high point:

• 2" (5 cm) abovethe high point for sectional door and

one-piecedoor with track.

• 8" (20 cm) abovethe high point for one-piecedoor without

track.

This height will providetravel clearancefor the top edge of the

door.

NOTE:If the total number of inches exceedstheheight

availablein your garage,use the maximum height possible, or

refer to page 13 for ceiling installation.

Header Wall

Unfinished

Ceiling _ OPTIONALBRACKETHEADERFORMOUNTCEILING

Vertical Centerline

of Garage Door

2x4

Structural

Supports

Header Wall

"_-_--2" (5 cm) Track

Highest Point

of Travel

--Door

Sectional door with curved track

Header Wall Track

Highest Point

_oHf Travel

One-piece door with horizontal track

Door

Hardware

Header Wall

:8" (20 cm)

Highest

Point

One-piece door without track:

jamb hardware

Header Wall

: 8" (20cm)

Pivot

One-piece door without track:

pivot hardware

INSTALLATION STEP 2

Install theHeaderBracket

You can attachthe headerbracketeither to the wall abovethe

garagedoor, or to the ceiling. Follow the instructions which will

work bestfor your particular requirements. Donot install the

headerbracketoverdrywall. If installingintomasonry,use

concreteanchors(not provided).

WALLHEADERBRACKETINSTALLATION

* Centerthe bracket on the vertical centerline with the bottom

edge of the bracket on the horizontal line asshown (with the

arrow pointing toward the ceiling).

• Mark thevertical set of bracket holes. Drill 3/16" pilot holesand

fastenthe bracketsecurely to a structural support with the

hardware provided.

HARDWARESHOWNACTUALSIZE

Lag Screw

5/16"-9xl -5/8"

Header

- Wall

2x4

Structural

Support

Horizontal

Line

Highest Point of

Garage Door Travel

Wall Mount

Optional

Mounting Holes

Vertical

Centerline

Door

Lag Screws

5/16"x9x 1-5/8"

Spring

Garage

-- Door-

Vertical

Centerline

of Garage Door

CEILINGHEADERBRACKETINSTALLATION

• Extendthe vertical centerline onto the ceiling as shown.

• Centerthe bracket on the vertical mark, no more than

6" (15 cm) from the wall. Make sure the arrow is pointing away

from the wall. The bracketcan be mounted flush against the

ceiling when clearanceis minimal.

• Mark the side holes. Drill 3/16" pilot holes and fasten bracket

securelyto a structural support with the hardwareprovided.

Ceiling Mounting Holes

Header y

Bracket

6" (15 cm) Maximum

Door

Spring

//_ /_ _ -FinishedCeiling-

/ Vertical Centerline

_ of Garage Door

-- Lag Screws

5/16"x9x1-5/8"

- Header Wall --

iNSTALLATiON STEP 3

Attachthe Rail to the HeaderBracket

• Position the opener on the garagefloor below the header

bracket. Usepacking material asa protective base. NOTE:If the

door spring is in the wayyou'll needhelp. Havesomeone hold

theopener securely on a temporary support to allow the rail to

clearthe spring.

• Position the rail bracket againstthe headerbracket.

• Align the bracket holesand join with a clevis pin 5/16"x1-1/2"

as shown.

• Inserta ring fastenerto secure.

Header Wall

Header Bracket

Idler Pulley

Header

Bracket

Mounting

Hole

J Garage

Door

OpenerCarton or

Temporary

Support

HARDWARESHOWNACTUALSiZE

ClevisPin5/16"x1-1/2"

Ring Fastener

INSTALLATION STEP 4

Positionthe Opener

Follow instructions which applyto your door type as illustrated.

SECTIONALDOORORONE-PIECEDOORWITH TRACK

A 2x4 laid flat is convenient for setting an ideal door-to-rail

distance.

• Removefoam packaging.

• Raisethe opener onto a stepladder.You will need help at this

point if the ladder is not tall enough.

• Openthe door all the way and placea 2x4 laid flat on the top

section beneaththe rail.

• If the top section or panel hits the trolley whenyou raise

the door, pull down on the trolley releasearm to disconnect

inner and outer sections. Slide the outer trolley toward the

motor unit. Thetrolley can remain disconnected until

Installation Step 12 is completed.

To prevent damageto garage door, rest garage door opener

rail on 2x4 placedon top section of door.

Rail iil

_Door 2x4 is used to determine

tfheCOcrer_Ctg?ouating height

ENGAGED

ONE-PIECEDOORWITHOUTTRACK

A 2x4 on its side is convenientfor setting an ideal

door-to-rail distance.

• Removefoam packaging.

• Raisethe opener onto a stepladder.You will need help at this

point if the ladder is not tall enough.

• Openthe door all the way and placea 2x4 on its side on the

top section of the door beneaththe rail.

• Thetop of the door should be levelwith thetop of the motor

unit. Donot position the opener more than 4" (10 cm) above

this point.

H Header iii'

I I I._L _[T_acket ii.!_

i tfheCOrer_Ctg?ounting height

INSTALLATION STEP 5

Hangthe Opener

Threerepresentativeinstallations are shown. Yours may be

different. Hangingbrackets should be angled (Figure 1) to provide

rigid support. Onfinished ceilings (Figure2 and Figure3), attach

a sturdy metal bracket to structural supports before installing the

opener.This bracketand fastening hardwareare not provided.

1. Measurethe distancefrom eachside of the motor unit to the

structural support.

2. Cut both piecesof the hanging bracketto required lengths.

3. Drill 3/16" pilot holes in the structural supports.

4. Attach one end of eachbracketto a support with

5/16"-18xl -7/8" lag screws.

5. Fastenthe opener to the hanging brackets with

5/16"-18x7/8" hex bolts, lock washers and nuts.

6. Checkto make sure the rail is centered over the door (or in line

with the headerbracket if the bracket is not centeredabovethe

door).

7. Removethe 2x4. Operatethe door manually. If the door hits

the rail, raisethe header bracket.

NOTE:DONOTconnectpower to openerat this time.

HARDWARESHOWNACTUALSIZE

Hex Bolt

5/16"-18x7/8"

Nut 5/16"-18 Lock Washer 5/16"

To avoid possible SERIOUSINJURYfrom afalling garage door

opener,fasten it SECURELYto structural supports of the

garage.Concreteanchors MUSTbe usedif installing any

brackets into masonry.

Figure1

Supports

Measure ',

Distance

Bolt 5/16"-18x7/8"

Lock

Nut 5/16"-18

Lag Screws

5/16"-18xl -7/8"

Figure2

Bolt 5/16"-18x7/8"

Lock Washer 5/16"

Nut 5/16"- 18

FINISHED CEILING

(Not Provided)

Bolt 5/16"-18x7/8"

Lock Washer 5/16"

Nut 5/16"-18

Figure3

Bolt 5/16"-18x7/8"

Lock Washer 5/16"

Nut 5/16"- 18

(Not Provided)

Bolt 5/16"-18x7/8"

Lock Washer 5/16"

Nut 5/16"-18

INSTALLATION STEP 6

Install theDoorControl

Locate door control within sight of door, at a minimum height of

5 feet (1.5 m) where small children cannot reach, awayfrom

moving parts of door and door hardware.

1. Strip 1/4" (6 mm) of insulation from oneend of bell wire and

connect to the two terminal screws on back of door control by

color: white to 2 and white/red to 1.

2. Fastenthe Door Control Button securelywith 6ABx1-1/2"

screws. If installing into drywall, drill 5/32" holes and usethe

anchors provided.

3. Runbell wire up wall and across ceiling to motor unit. Use

insulated staples to secure wire in severalplaces. Donot pierce

wire with a staple, creating a short or open circuit.

4. Connectthe bell wire to the quick-connect terminals on the

motor unit panel:white to white; white/red to red.

5. Position the antennawire as shown.

6. Usetacks or staplesto permanently attachentrapment warning

label to wall near door control, and manual release/safety

reversetest label in a prominent location on inside of garage

door.

NOTE:DONOTconnectpower and operateopener at this time.

Thetrolley will travel to the furl open position but will not return

to the close position until thesensor beamis connectedand

properly aligned.

To prevent possible SERIOUSINJURYor DEATHfrom

electrocution:

• Besure power is not connected BEFOREinstalling door

control.

• ConnectONLYto 24 VOLTlow voltage wires.

To prevent possible SERIOUSINJURYor DEATHfrom a closing

garagedoor:

• Install door control within sight of garagedoor, out of reach

of children at a minimum height of 5 feet (1.5 m) and away

from ALL moving parts of door.

• NEVERpermit children to operateor play with door control

push buttons or remote control transmitters.

• Activate door ONLYwhen it can be seenclearly, is properly

adjusted and there are no obstructions to door travel.

• ALWAYSkeepgarage door in sight until completely closed.

NEVERpermit anyoneto cross path of closing garage door.

HARDWARESHOWNACTUALSIZE

Screw 6ABx1-1/2" Insulated

Lighted Door Control Button Drywall Anchors Staples

Te,e ,w t, VV,re

(BACK VIEW)

DOOR CONTROL BUTTON

Quick-Connect

To release or insert wire,

push in tab with

screwdriver tip

Strip wire 7/16" Red/

(11 mm)

7/16" (11 mrn)l

Door Control

Connections

White Grey

Antenna

INSTALLATION STEP 7

Install theLights

• Pressthe releasetabs on both sides of lens. Gentlyrotate lens

back and downward until the lens hinge is in thefully open

position. Do not removethe lens.

• Install a 100 watt maximum light bulb in eachsocket. Light

bulb size should be A19, standard neckonly. The lights will

turn ONand remain lit for approximately 4-1/2 minutes when

power is connected.Thenthe lights will turn OFF.

• Reversethe procedureto close the lens.

• UseA19,standard neck garagedoor opener bulbs for

replacement.

NOTE:Useonly standard light bulbs. Theuseof short neck or

speciafity light bulbs may overheatthe endpanel or light socket.

To prevent possible OVERHEATINGof the endpanelor light

socket:

• DONOTuse short neck or specialty light bulbs.

• DONOTuse halogen bulbs. UseONLYincandescent.

To prevent damageto the opener:

• DONOTuse bulbs larger than IOOW.

• ONLYuseA19 size bulbs.

Release Tab

100 Watt (Max) _ )

Standard Light Bulb

100 Watt (Max)

Standard

Light Bulb --

Lens

Hinge

INSTALLATION STEP 8

AttachtheEmergencyRe/ease Ropeand Hand/e

- Threadone end of the rope through the hole in the top of the

red handleso "NOTICE"readsright side up asshown. Secure

with an overhandknot at least 1" (2.5 cm) from the end of the

ropeto prevent slipping.

• Threadthe other end of the rope through the hole in the release

arm of the outer trolley.

• Adjust rope lengthso the handle is 6 feet (1.83 m) abovethe

floor. Ensurethat the rope and handle clearthe tops of all

vehiclesto avoid entanglement.Securewith an overhand knot.

NOTE:If it is necessaryto cut the rope, heat sealthe cut end with

a match or lighter to prevent unraveling.

To prevent possible SERIOUSINJURYor DEATHfrom a falling

garagedoor:

• If possible, useemergencyreleasehandleto disengage

trolley ONLYwhen garagedoor is CLOSED.Weakor broken

springs or unbalanceddoor could result in an open door

falling rapidly and/or unexpectedly.

• NEVERuseemergency releasehandle unless garage

doorway is clear of persons and obstructions.

• NEVERusehandle to pull door open or closed. If rope knot

becomesuntied, you could fall.

Trolley

Emergency _ _. Overhand

Release Handle _Knot

INSTALLATION STEP 9

E/ectrica/ Requirements

To avoidinstallationdifficulties,do notrunthe openerat this

time.

To reducethe risk of electric shock, your garagedoor opener has

a grounding type plug with a third grounding pin. This plug will

only fit into a grounding type outlet. If the plug doesn't fit into the

outlet you have, contact a qualified electricianto install the proper

outlet.

RIGH_

To prevent possible SERIOUSINJURYor DEATHfrom

electrocution or fire:

• Besure power is not connectedto the opener,and

disconnect power to circuit BEFOREremoving cover to

establish permanentwiring connection.

• Garagedoor installation and wiring MUSTbe in compliance

with ALL local electrical and building codes.

• NEVERusean extension cord, 2-wire adapteror change

plug in ANYway to make it fit outlet. Besure the opener is

grounded.

PERMANENT WIRING

CONNECTION

If permanent wiringis requiredbyyourlocal code,refer to the

followingprocedure.

To make a permanent connection through the 7/8" hole in the top

of the motor unit:

• Removethe motor unit cover screws and set the cover aside.

• Removethe attached3-prong cord.

• Connectthe black (line) wire to the screw on the brass

terminal; the white (neutral) wire to the screw on the silver

terminal; and the ground wire to the green ground screw. The

openermustbe grounded.

• Reinstallthe cover.

To avoidinstallationdifficulties,do notrunthe openerat this

time.

Ground Tab

Green

Ground Screw

Ground Wire

White Wire Wire

INSTALLATION STEP 10

Install TheProtectorSystem

Thesafety reversingsensormustbeconnectedand aligned

correctlybeforethe garagedooropenerwill movein the down

direction.

IMPORTANTINFORMATIONABOUTTHESAFETYREVERSING

SENSOR

When properly connectedand aligned, the sensor will detect an

obstacle in the pathof its electronic beam. Thesending eye (with

an amber indicator light) transmits an invisible light beamto the

receiving eye (with a green indicator light). If an obstruction

breaks the light beamwhile the door is closing, the door will stop

and reverseto full open position, and the opener lights will flash

10 times.

Theunits must be installed inside the garageso that the sending

and receivingeyes face eachother across the door, no morethan

6" (15 cm) abovethefloor. Either can be installed on the left or

right of the door as long as the sun nevershines directly into the

receiving eye lens.

Themounting brackets are designedto clip onto the track of

sectional garagedoors without additional hardware.

Be sure power is not connectedto the garagedoor opener

BEFOREinstalling the safety reversing sensor.

To prevent SERIOUSINJURYor DEATHfrom a closing garage

door:

• Correctly connect and align the safety reversingsensor. This

required safety deviceMUST NOTbe disabled.

• Install the safety reversing sensor so beamis NOHIGHER

than 6"(15 cm) above garagefloor.

If it is necessaryto mount the units on the wall, the brackets

must be securelyfastenedto a solid surface such asthe wall

framing. Extensionbrackets (seeAccessories) are availableif

needed.If installing in masonry construction, add a pieceof wood

at eachlocation to avoid drilling extra holesin masonry if

repositioning is necessary.

Theinvisible light beam path must be unobstructed. No part of

the garagedoor (or door tracks, springs, hinges, rollers or other

hardware) may interrupt the beamwhile the door is closing.

IH, i 111

Facingthe doorfrom insidethegarage

Page is loading ...

Craftsman 13953904D Owner's manual

Brand: Craftsman

Model: 13953904D

Category: Garage Door Opener

Type: Owner's manual

Download PDF

report

in other languages

español: Craftsman 13953904D El manual del propietario

Craftsman 13953904D Owner's manual

Craftsman 13953904D Owner's manual

in other languages

Related papers

Other documents