Frigidaire 959924 Owner's manual

Brand: Frigidaire

Model: 959924

Category: Fridge-freezers

Type: Owner's manual

TABLE OF CONTENTS

www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352

All about the

Use & Care

of your Refrigerator

A04555603 (January 2018)

Important Safety Instructions ......................2

Features at a Glance ...................................4

Installation ................................................5

Door Removal/Reversal Instructions

(some models) ...........................................7

Handle Installation ...................................10

Connecting the Water Supply ....................12

Ice Service ...............................................14

Controls ...................................................15

Optional Features .....................................16

Normal Operating Sounds and Sights ......... 18

Care & Cleaning .......................................19

Before You Call ........................................21

Major Appliance Warranty .........................22

WARNING

WARNING indicates a potentially hazardous

situation which, if not avoided, could result

in death or serious injury.

IMPORTANT

IMPORTANT indicates installation, operation

or maintenance information which is impor-

tant but not hazard-related.

DANGER

DANGER indicates an imminently hazardous

situation which, if not avoided, will result in

death or serious injury.

Denitions

This is the safety alert symbol. It is used to

alert you to potential personal injury hazards.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

Doors

 Handles are secure and tight

 Door seals completely to cabinet on all sides

 Freezer door is level across the top

Leveling

 Refrigerator is level, side-to-side and

tilted ¼” (6mm) front-to-back

 Toe grille is properly attached to refrigerator

 Cabinet is setting solid on all corners

Electrical Power

 House power turned on

 Refrigerator plugged in

Ice Maker

 House water supply connected to refrigerator

 No water leaks present at all connections

- recheck in 24 hours

 Ice maker is turned ON

 Ice & water dispenser operates correctly

 Frontltermustbeushwithlter

housing (select models)

Final Checks

 Shipping material removed

 Fresh food and freezer temperatures set

 Crisper humidity controls set

 Registration card sent in

Installation Checklist

CAUTION

CAUTION indicates a potentially hazardous

situation which, if not avoided, may result in

minor or moderate injury.

IMPORTANT SAFETY INSTRUCTIONS

For your Safety

• DO NOT store or use gasoline, or other

ammableliquidsinthevicinityofthisor

any other appliance. Read product labels

forwarningsregardingammabilityand

other hazards.

• DO NOT operate the refrigerator in the

presence of explosive fumes.

• Avoid contact with any moving parts of

automatic ice maker.

• Remove all staples from the carton.

Staples can cause severe cuts, and also

destroynishesiftheycomeincontact

with other appliances or furniture.

WARNING

Please read all instructions before using this

refrigerator.

Child Safety

Destroy or recycle the carton, plastic bags, and

any exterior wrapping material immediately

after the refrigerator is unpacked. Children

should never use these items to play. Cartons

covered with rugs, bedspreads, plastic

sheets or stretch wrap may become airtight

chambers,andcanquicklycausesuffocation.

Proper Disposal of your

Refrigerator or Freezer

Risk of child entrapment

Child entrapment and suffocation are not

problems of the past. Junked or abandoned

refrigerators or freezers are still dangerous –

even if they will sit for “just a few days”. If you

are getting rid of your old refrigerator or freezer,

please follow the instructions below to help

prevent accidents.

IMPORTANT SAFETY INSTRUCTIONS

Grounding type wall receptacle

Power cord with

3-prong grounded plug

Do not, under

any circumstances,

cut, remove,

or bypass the

grounding prong.

Electrical information

• The refrigerator must be plugged into its

own dedicated 115 Volt, 60 Hz., 15 Amp,

AC only electrical outlet. The power cord of

theapplianceisequippedwithathree-

prong grounding plug for your protection

against electrical shock hazards. It must be

plugged directly into a properly grounded

three prong receptacle. The receptacle

must be installed in accordance with local

codesandordinances.Consultaqualied

electrician. Avoid connecting refrigerator to

a Ground Fault Interrupter (GFI) circuit. Do

not use an extension cord or adapter plug.

• If the power cord is damaged, it should

be replaced by an authorized service

technician to prevent any risk.

• Never unplug the refrigerator by pulling

on the power cord. Always grip the

plugrmly,andpullstraightoutfrom

the receptacle to prevent damaging the

power cord.

• Unplug the refrigerator before cleaning

and before replacing a light bulb to avoid

electrical shock.

• Performance may be affected if the voltage

varies by 10% or more. Operating the

refrigeratorwithinsufcientpowercan

damage the compressor. Such damage is

not covered under your warranty.

• Do not plug the unit into an electrical

outlet controlled by a wall switch or pull

WARNING

These guidelines must be followed to ensure

that safety mechanisms in this refrigerator

will operate properly.

IMPORTANT

Turning the Refrigerator controls to “0” will

disable your refrigerator’s cooling system,

but does not disconnect the power to the

light bulb and other electrical components.

To turn off power to your refrigerator you

must unplug the power cord from the elec-

trical outlet.

Proper Disposal of Refrigerators/Freezers

We strongly encourage responsible appliance

recycling/disposal methods. Check with your utility

company or visit www.energystar.gov/recycle for

more information on recycling your old refrigerator.

Before you throw

away your old

refrigerator/

freezer:

• Remove doors.

• Leave shelves in

place so children

may not easily

climb inside.

• Have refrigerant

removed by a

qualiedservicetechnician.

IMPORTANT

CFC/HCFC Disposal

Your old refrigerator may have a cooling

systemthatusedCFCsorHCFCs(chlorouo-

rocarbonsorhydrochlorouorocarbons).CFCs

and HCFCs are believed to harm stratospheric

ozone if released to the atmosphere. Other

refrigerants may also cause harm to the envi-

ronment if released to the atmosphere.

If you are throwing away your old refrigera-

tor, make sure the refrigerant is removed for

properdisposalbyaqualiedtechnician.If

you intentionally release refrigerant, you may

besubjecttonesandimprisonmentunder

provisions of environmental legislation.

cord to prevent the refrigerator from

being turned off accidentally.

FEATURES AT A GLANCE

Features may vary according to model

IMPORTANT

Cleaning your Refrigerator

Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small

amountofliquiddishsoapovertheadhesivewithyourngers.Rinsewithwarmwaterand

dry with a soft cloth.

Donotusesharpinstruments,rubbingalcohol,ammableuids,orabrasivecleanersto

remove tape or glue. These products can damage the surface of your refrigerator.

After you remove all of the package materials, clean the inside of your refrigerator before us-

ing it. See the “Care & Cleaning” section in this manual.

See important information about cleaning glass shelves and covers in the “Optional Features”

section of this manual.

IMPORTANT

Moving your Refrigerator

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to

covertheoorwithcardboardorhardboardtoavoidoordamage.Alwayspulltherefrigera-

tor straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move

itasoordamagecouldoccur.

Ice Maker

Ice Bucket

Freezer Shelf

Auxiliary Freezer

Control

Refrigerator

Control

Deli Drawer

Cover

Deli Drawer

(Some Models)

Full Shelf

Crisper

Cover

Crisper

Drawers

Ice Tray

Fixed Door

Bin

Door Rack

Dairy Door

Fixed

Door Bin

Door Rack

Toe Grille

Full Width Deli

(Some Models)

Deli Drawer

Cover

Upper Door

Rack

INSTALLATION



NOTE

If your refrigerator is placed with the door

hinge side against a wall, you may have to

allow additional space for the handle so the

door can be opened wider.

CAUTION

Do not install the refrigerator where the

temperature will drop below 55°F (13°C) or rise

above 110°F (43°C). The compressor will not

be able to maintain proper temperatures inside

the refrigerator.

Do not block the toe grille on the lower front

ofyourrefrigerator.Sufcientaircirculation

is essential for the proper operation of your

refrigerator.

This Use & Care Guide provides general

operating instructions for your model. Use the

refrigerator only as instructed in this Use &

Care Guide. Before starting the refrigerator,

followtheseimportantrststeps.

Location

• Choose a place that is near a grounded

electrical outlet. Do Not use an extension

cord or an adapter plug.

• If possible, place the refrigerator out of

direct sunlight and away from the range,

dishwasher or other heat sources.

• The refrigerator must be installed on a

oorthatislevelandstrongenoughto

support a fully loaded refrigerator.

• Consider water supply availability for

modelsequippedwithanautomaticice

maker. If you do not hook up water to

the refrigerator, remember to turn the ice

maker off.

Installation

Installation clearances

• Allow the following clearances for ease

of installation, proper air circulation, and

plumbing and electrical connections:

 Sides&Top ⅜inch

Back 1 inch

Guidelines for nal positioning of your

refrigerator:

• All four corners of the cabinet must rest

rmlyontheoor.

• The cabinet should be level at the front

and rear.

• The sides should tilt ¼-inch (6 mm) from

front-to-back (to ensure that doors close

and seal properly).

• Doors should align with each other and be

level.



NOTE

For additional instructions on garage instal-

lation, refer to “Controls” section.



NOTE

Raise the front of the refrigerator enough so

the doors close freely when opened halfway.

The refrigerator should slope ¼ inch to ½

inch from front-to-back. Then level the refrig-

erator from side-to-side.

To level the cabinet using the front

rollers:

1 Remove the toe grille.

Raise

9/16"

(14 mm)

Max

Figure 3

9/16"

(14 mm)

Max

Raise

Figure 2

3 Use adjustable wrench to adjust leveling

screws. Lower the leveling screws on each

sideclockwiseuntiltheycontacttheoor

(Figure 3). Do not raise the cabinet more

than

inch.

INSTALLATION

 2 Useaat-bladescrewdriveror⅜inch

socket wrench to raise or lower the front

rollers (Figure 2). Do not raise the cabinet

more than

inch.

DOOR REMOVAL/REVERSAL INSTRUCTIONS

(SOME MODELS)



NOTE

The direction in which

your refrigerator doors

open (door swing) can

be reversed, from left to

right or right to left, by

moving the door hinges

from one side to the other.

Reversing the door swing

should be performed by a

qualiedperson.

IMPORTANT

Before you begin, turn the

refrigerator temperature

control to “0” and remove

the electrical power cord

from the wall outlet. Re-

move any food from door

shelves.

Top Hinge

Cover Front

Screw

Top Hinge

Cover Rear

Screw

Bottom

Hinge

Screw

Top

Hinge

Screw

Adjustable

Wrench

Socket

Wrench Set

3/8" (10mm)

Fixed

Wrench

Tools Necessary:

Phillips

Head

Door removal and reversal

instructions:

1. Remove toe grille.

2. Remove top hinge cover. Trace around the

hinge with a soft lead pencil. This makes

reinstallation easier. Remove top hinge and

lift door off center hinge pin. Set door aside.

Door

Stop

Shim

Washer

Hinge

Center

Hinge

Screws

Hinge

Hole

Plug

Handle

Hole

Plug

Door

Stop

Screw

Washer

Hinge

Bottom

Hinge

Screws

Toe

Grille

Door Stop

Screw

Door

Stop

Top

Hinge

Cover

Top

Hinge

 7. Removetwoscrewsonbottomhingewith⅜”

socket wrench.

8. Install bottom hinge on opposite side with

the two screws removed from step 7.

3. Unscrew center hinge pin using adjustable

wrench and save for reassembly. Ensure

plastic washer stays on hinge pin.

4. Lift refrigerator door off of bottom hinge

and set aside.

5. Remove center hinge and shim by

removing inside screw and loosening two

outside screws enough to allow hinge and

shim to slide out. Tighten screws.

6. Loosen two outside screws on opposite

side of refrigerator, remove inside screw

and install center hinge.

9. Unscrew bottom hinge pin using

adjustable wrench. Move hinge pin to

other hole in hinge and tighten with

adjustable wrench.

10. Reverse door handles (see instruction on

next page).

11. Move freezer and refrigerator door stops

to opposite side. Before starting screws,

use an awl to puncture the foam.

12. Position refrigerator door onto bottom

hinge pin and screw center hinge pin

through center hinge into top of door.

Close refrigerator door to help align hinge

hole.

13. Tighten center hinge pin with adjustable

wrench.

14. Remove cabinet and hinge hole plugs and

move to opposite side.

15. Lower freezer door onto center hinge pin.

16. Close freezer door. Lift up on handle side

of door and grasp the thinnest part of

the top hinge cover (which was removed

in Step 2) and insert the thickest part

between the doors on the handle side

approximately 3 inches from the outside

edge. This will ensure proper spacing.

Look for open areas between the

gasket and the cabinet flange.

Gasket should seal against the

cabinet all the way around including top

and bottom

17. Tighten the top hinge screws and check

door gasket for open seal condition (gap

betweengasketandcabinetange).

DOOR REMOVAL/REVERSAL INSTRUCTIONS

(SOME MODELS)

IMPORTANT

If the condition still exists, try heating

the gasket with a hair dryer with the door

closed. Use Caution and be careful not to

damage the interior door panel or gasket by

applying too much heat.

18. Should open seal condition exist, try to

massage the gasket to make sure it is

seated into the channel.

19. If the open seal condition still exists, it

maybenecessarytoipthegasket.In

this case, remove the gasket from the

door by pulling it out. Rotate the gasket

half a turn (180 degrees). Reinstall the

gasketbyinsertingthecornersrstthen

work towards the middle assuring that it is

fully seated in the channel.

20. Flip toe grille and reinstall.

21. Plug in electrical power cord and turn

refrigerator temperature control to center

position. Adjust setting as necessary.

DOOR REMOVAL/REVERSAL INSTRUCTIONS

(SOME MODELS)

IMPORTANT

To ensure proper installation of handles,

please review these instructions and il-

lustrations thoroughly prior to installing the

handles.

Additionally, before installing the door han-

dles, make sure the door swing is correct.

Your model will have either a right hand or

left hand door swing. Follow instructions in

the Use & Care Guide to reverse the doors,

if necessary.

HANDLE INSTALLATION

To attach metal refrigerator handle:

1. Place rounded part of handle onto

shoulder screw on face of door and align

the two holes in top of handle with the

two holes in top of door. Do not tighten

the set screw yet.

2. Install the two screws into the top of the

handle.

3. Tighten the set screw on the rounded part

ofthehandleuntilthehandleisushwith

the door, then tighten another ½ turn.

CAUTION

Wear gloves and use extreme CAUTION

when installing these handles. The rounded

end of the handles may be sharp.

To attach metal freezer handle:

1. Place rounded part of handle onto

shoulder screw on face of door and align

the two holes in bottom of handle with

the two holes in bottom of door. Do not

tighten the set screw yet.

Stainless Steel Models

2. Install the two screws into the bottom of

the handle.

3. Tighten the set screw on the rounded part

ofthehandleuntilthehandleisushwith

the door, then tighten another ½ turn.

Screw

Handle

Button

Plug

Set

Screw

Shoulder

Screw

Handle

Shoulder

Screw

Set

Screw

Shoulder

Screw

Set

Screw

Handle

Screw

Shoulder

Screw

Nameplate

Handle

Set Screw

Screw

To reverse metal refrigerator/freezer

handles:

Handles may be easier to reverse while doors

are off. Reverse freezer and refrigerator

handles as shown.

CAUTION

Be sure doors are set aside in a secure

position where they cannot fall and cause

personal injury.

HANDLE INSTALLATION

CAUTION

Do not use an electric screwdriver to attach

handles; overtightening handles may crack

them. Use a handheld screwdriver only.

These screws

are packaged

with the

handles.

To attach plastic refrigerator handle:

1. With the door open, place the end of the

handle on the dove tail mounting screw

and pull down to secure in place.

2. Align handle base with holes in top of

door.

3. Install screws packaged with the handle.

Handle

Manija

Poignée

Screws

Los tornillos

Vis

Handle Base

Base de mango

Base de poignée

To attach plastic freezer handle:

1. With the door open, place the end of the

handle on the dove tail mounting screw

and push up to secure in place.

2. Align handle base with holes in bottom of

door.

3. Install screws packaged with the handle.

Mounting Screw

Handle Base

Screws

Handle

CONNECTING THE WATER SUPPLY

WARNING

To avoid electric shock, which can cause

death or severe personal injury, disconnect

the refrigerator from electrical power before

connecting a water supply line to the

refrigerator.

CAUTION

To Avoid Property Damage:

• Copper or Stainless Steel braided tubing

is recommended for the water supply

line. Water supply tubing made of ¼

inch plastic is not recommended to be

used. Plastic tubing greatly increases

the potential for water leaks, and the

manufacturer will not be responsible for

any damage if plastic tubing is used for

the supply line.

• DO NOT install water supply tubing in

areas where temperatures fall below

freezing.

• Chemicals from a malfunctioning softener

can damage the ice maker. If the ice

maker is connected to soft water, ensure

that the softener is maintained and

working properly.

IMPORTANT

Ensure that your water supply line connec-

tions comply with all local plumbing codes.



NOTE

Check with your local building authority

for recommendations on water lines and

associated materials prior to installing your

new refrigerator. Depending on your local/

state building codes, Frigidaire recommends

for homes with existing valves its Smart

Choice

water line kit 5305513409 (with

a 6 ft. Stainless Steel Water Line) and for

homes without an existing valve, Frigidaire

recommends its Smart Choice

water line

kit 5305510264 (with a 20 ft. Copper Water

Line with self-tapping saddle valve). Please

refer to www.frigidaire.com/store for more

information.

Before Installing The Water Supply Line,

You Will Need:

• BasicTools:adjustablewrench,at-blade

screwdriver, and Phillips

screwdriver

• Access to a household cold water line

with water pressure between 30 and 100

psi.

• A water supply line made of ¼ inch

(6.4 mm) OD, copper or stainless steel

tubing. To determine the length of tubing

needed, measure the distance from the

ice maker inlet valve at the back of the

refrigerator to your cold water pipe. Then

add approximately 7 feet (2.1 meters),

so the refrigerator can be moved out for

cleaning (as shown).

• A shutoff valve to connect the water

supply line to your household water

system. DO NOT use a self-piercing type

shutoff valve.

• Donotre-usecompressionttingoruse

thread seal tape.

• A compression nut and ferrule (sleeve) for

connecting a copper water supply line to

the ice maker inlet valve.

Figure 2

Steel

Clamp

Braided

Flexible

Stainless

Steel

Water Line

Water Valve

Bracket

Valve Inlet

Water Valve

6 ft (1.8 Meters) Braided flexible

stainless steel water line from

household water supply.

Plastic Water Tubing

to Ice Maker

Fill Tube

(Include enough tubing in loop to allow

moving refrigerator out for cleaning.)

Figure 1

Plastic Water

Tubing to Ice

Maker Fill

Tube

Steel

Clamp

Brass

Compression

Nut

Ferrule

(Sleeve)

Copper

water line

Water Valve

Bracket

Valve Inlet

Water Valve

Copper water line

from household

water supply

(Include enough tubing in loop to allow

moving refrigerator out for cleaning.)

CONNECTING THE WATER SUPPLY

To Connect Water Supply Line To Ice

Maker Inlet Valve

1. Disconnect refrigerator from electric power

source.

2. Place end of water supply line into sink or

bucket.TurnONwatersupplyandush

supply line until water is clear. Turn OFF

water supply at shutoff valve.

3. Remove plastic cap from water valve inlet

and discard cap.

4. If you use copper tubing - Slide brass

compression nut, then ferrule (sleeve)

onto water supply line. Push water supply

line into water valve inlet as far as it

will go (¼ inch / 6.4 mm). Slide ferrule

(sleeve)intovalveinletandngertighten

compression nut onto valve. Tighten

another half turn with a wrench; DO NOT

over tighten. See Figure 1.

If you use braided exible stainless

steel tubing - The nut is already

assembled on the tubing. Slide nut onto

valveinletandngertightennutonto

valve. Tighten another half turn with a

wrench; DO NOT over tighten. See Figure

5. With steel clamp and screw, secure water

supply line (copper tubing only) to rear

panel of refrigerator as shown.

6. Coil excess water supply line (copper

tubing only), about 2½ turns, behind

refrigerator as shown and arrange coils so

they do not vibrate or wear against any

other surface.

7. Turn ON water supply at shutoff valve and

tighten any connections that leak.

8. Reconnect refrigerator to electrical power

source.

9. To turn ice maker on, lower wire signal

arm (side mounted) or set the ice maker’s

On/Off power switch to the “I” position

(rear mounted).



NOTE

These instructions do not cover after market

ice maker installation. Instructions in after

market ice maker kit should be used.

IMPORTANT

Your ice maker is shipped from the factory

with the wire signal arm in the ON position.

To ensure proper function for your ice maker,

hook up water supply immediately or turn ice

maker OFF by lifting the wire signal arm until

it clicks and locks in the UP position. If the

ice maker is on and the water supply is not

connected, the water valve will make a loud

chattering noise.

ICE PRODUCTION: WHAT

TO EXPECT

The ice maker will produce 2.5 to 3 pounds

of ice every 24 hours depending on usage

conditions. Ice is produced at a rate of 8 cubes

every 80 to 160 minutes.

CAUTION

Do Not place the ice container in your

dishwasher.

ICE SERVICE

If your refrigerator has an automatic ice maker,

minimalicewillbeproducedduringtherst24

hours of operation. Air in new plumbing lines

may cause the ice maker to cycle two or three

times before making a full tray of ice. With no

usage, it will take approximately one to two

daystolltheicecontainer.

Newplumbingconnectionsmaycausetherst

production of ice cubes to be discolored or

haveanoddavor.Discardicemadeduring

therst24hours.



NOTE

Automatic ice makers are also optional

accessories that may be installed in most

models at any time. Call your local dealer for

information.

Turning your Ice Maker On

After the plumbing connections have been

completed, the water supply valve must be

opened. Place the ice container under the

ice maker, pushing it as far back as possible.

Lower the wire signal arm to its “down” or ON

position.

Turning your Ice Maker Off

To stop the ice maker, lift the wire signal

arm until it clicks and locks in the “up” or

OFF position. The ice maker also turns off

automatically when the ice container is full.

OFF

Wire

Signal Arm

IMPORTANT

Adjusting the refrigerator temperature control

to “0” turns off the compressor and prevents

the refrigerator from cooling, but does not dis-

connect the power to the light bulb and other

electrical components. To turn off power to

your refrigerator, you must unplug the power

cord from the wall outlet.



NOTE

Whenrstturningrefrigeratoron,adjust

control to recommended. This is the recom-

mended initial setting. After 24 hours, adjust

the controls as needed.

Refrigerator Control

Allow 24 hrs for adjustments

Auxiliary Freezer Control

Temperature Adjustment

• Adjust temperature gradually: adjust the

knob in small increments, allowing the

temperature to stabilize.

• For colder temperatures, adjust the knob

towards coldest.

• For warmer temperatures, adjust the

knob towards cold.

Adjusting the refrigerator control will change

temperatures in both compartments. The

auxiliary freezer control can be left at the factory

pre-set (mid position) or adjusted as desired;

it has no effect on electrical power to the

refrigerator.

To maintain temperatures, a fan circulates air

in the refrigerator and freezer compartments.

For good circulation, do not block cold air vents

with food items.

Cool Down Period

To ensure safe food storage, allow the

refrigerator to operate with the doors closed

for at least 8 hours before loading it with food.

Refrigerator & Freezer Controls

CONTROLS

CAUTION

Do not install the refrigerator where the

temperature will drop below 55°F (13°C) or

rise above 110°F (43°C). The compressor

will not be able to maintain proper

temperatures inside the refrigerator.

IMPORTANT

If you install your refrigerator in a garage or

other unheated area, you may experience

freezer temperature problems during the winter

months when temperatures dip below 55° F.

Upgrading your refrigerator with a Ga-

rage Kit will lower the minimum operating

temperature of your unit to 34° F. This kit

can be ordered by calling the phone number

listed at the bottom of the warranty page or

back cover at an additional cost.

OPTIONAL FEATURES

Shelf Adjustment

Refrigerator shelves are easily adjusted to suit

individual needs. Before adjusting the shelves,

remove all food.

To adjust sliding shelves:

1. Remove shelf by pulling forward to stop

position.

2. Lift front edge up and pull out.

To replace shelf, rest side edges on any pair

of shelf rails and carefully push shelf back into

position.

Sliding Glass Shelf

Sliding Wire Shelf

Door Rack

Door storage

Door bins, shelves, and racks are provided for

convenient storage of jars, bottles, and cans.

Frequentlyuseditemscanbequicklyselected.

The dairy compartment, which is warmer than

the general food storage section, is intended for

short term storage of cheese, spreads, or butter.

Door rack

Some models have door racks or bins that can

accommodate gallon-sized plastic drink containers

and economy-sized jars and containers.

To remove door rack:

1. Push on rack sides to release from locking tabs.

2. Pull straight out.

To install door rack:

1. Push rack straight ahead.

2. You will hear the sides lock into the tabs.

CAUTION

Do not clean glass shelves or covers with

warm water when they are cold. Shelves

and covers may break if exposed to sudden

temperature changes or impact, such as

bumping. Tempered glass is designed to

shatter into many small, pebble-size pieces.

This is normal. Glass shelves and covers are

heavy. Use both hands when removing them

to avoid dropping.

CAUTION

To avoid personal injury or property

damage, handle tempered glass shelves

carefully. Shelves may break suddenly if

nicked, scratched, or exposed to sudden

temperature change.



NOTE

Leafy vegetables keep best when stored

with the Humidity Control set on High

Humidity, or in a drawer without a Humid-

ity Control. This keeps incoming air to a

minimum and maintains maximum moisture

content. Store non-leafy vegetables and

fruits still in their skins at the low humidity

setting.

Crisper Humidity Control (some

models)

The crisper humidity control, present on the

crisper drawers of some models, allows you to

adjust the humidity within the crisper. This can

extend the life of fresh vegetables that keep

best in high humidity.

Low

Humidity

High

Humidity

Higher Humidity Lower Humidity

OPTIONAL FEATURES

Crispers (some models)

The crispers, located under the bottom

refrigerator shelf, are designed for storing

fruits, vegetables, and other fresh produce.

Wash items in clear water and remove excess

water before placing them in the crispers.

Items with strong odors or high moisture

content should be wrapped before storing.



NOTE

Rigid foam insulation is very energy ef-

cient,butisnotasoundinsulator.

Understanding the sounds you

may hear

Yournew,high-efciencyrefrigeratormay

introduce unfamiliar sounds. These sounds

normally indicate your refrigerator is operating

correctly.Somesurfacesonoors,walls,and

kitchen cabinets may make these sounds more

noticeable.

IMPORTANT

During the automatic defrost cycle, you may

notice a red glow in the vents on the back

wall of your freezer compartment. This is

normal during the defrost cycle.

Following is a list of major components in your

refrigerator and the sounds they can cause:

A Evaporator Refrigerant through the

evaporator may create a boiling or

gurgling sound.

B Evaporator fan You may hear air being

forced through the refrigerator by the

evaporator fan.

C Defrost heater During defrost cycles,

water dripping onto the defrost heater

may cause a hissing or sizzling sound.

After defrosting, a popping sound may

occur.

D Automatic ice maker When ice has

been produced, you will hear ice cubes

falling into the ice bin.

E Automatic Defrost control These parts

can produce a snapping or clicking sound

when turning the cooling system on and off.

F Condenser fan You may hear air being

forced through the condenser.

G CompressorModern,high-efciency

compressors run much faster than in the

past. The compressor may have a high-

pitched hum or pulsating sound.

H Water valve If your refrigerator is

equippedwithanautomaticicemaker,

you will hear a buzzing sound as the water

valveopenstolltheicemakerduring

each cycle.

I Drain pan (not removable) You may hear

water dripping into the drain pan during

the defrost cycle.

J Condenser May create minimal sounds

from forced air.

NORMAL OPERATING SOUNDS AND SIGHTS

IMPORTANT

If you store or move your refrigerator in

freezing temperatures, be sure to completely

drain the water supply system. Failure to

do so could result in water leaks when the

refrigerator is put back into service. Contact a

service representative to perform this opera-

tion.

CAUTION

• Pull the refrigerator straight out to move

it. Shifting it from side to side may

damageooring.Becarefulnottomove

the refrigerator beyond the plumbing

connections.

• Damp objects stick to cold metal surfaces.

Do not touch refrigerated surfaces with wet

or damp hands.



NOTE

If you set your temperature controls to turn

off cooling, power to lights and other electri-

cal components will continue until you unplug

the power cord from the wall outlet.

Protecting your investment

Keeping your refrigerator clean maintains

appearance and prevents odor build-up. Wipe

up any spills immediately and clean the freezer

and fresh food compartments at least twice

a year. When cleaning, take the following

precautions:

• Never use CHLORIDE or cleaners with

bleach to clean stainless steel.

• Do not wash any removable parts in a

dishwasher.

• Always unplug the electrical power cord

from the wall outlet before cleaning.

• Remove adhesive labels by hand. Do

not use razor blades or other sharp

instruments which can scratch the

appliance surface.

• Do not remove the serial plate.

Do not use abrasive cleaners such as

window sprays, scouring cleansers, brushes,

ammableuids,cleaningwaxes,concentrated

detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior

doors, gaskets or cabinet liners. Do not use

paper towels, metallic scouring pads, or other

abrasive cleaning materials or strong alkaline

solutions.

CARE & CLEANING

Care & Cleaning Tips

Part What To Use Tips and Precautions

Interior &

Door Liners

• Soap and water

• Baking soda and

water

Use2tablespoonsofbakingsodain1quartofwarm

water. Be sure to wring excess water out of sponge

or cloth before cleaning around controls, light bulb

or any electrical part.

Door

Gaskets

• Soap and water Wipe gaskets with a clean soft cloth.

Drawers &

Bins

• Soap and water Use a soft cloth to clean drawer runners and tracks.

Glass

Shelves

• Soap and water

• Glass cleaner

• Mildliquidsprays

Allow glass to warm to room temperature before

immersing in warm water.

Toe Grille • Soap and water

• Mildliquidsprays

• Vacuum attachment

Vacuum dust from front of toe grille. Remove

toe grille (see Installation Instructions). Vacuum

backside, wipe with sudsy cloth or sponge. Rinse

and dry.

Exterior &

Handles

• Soap and water

• Non Abrasive Glass

Cleaner

Do not use commercial household cleaners

containing ammonia, bleach or alcohol to clean

handles. Use a soft cloth to clean smooth handles.

DO NOT use a dry cloth to clean smooth doors.

Exterior &

Handles

(Stainless

Steel

Models

Only)

• Soap and water

• Stainless Steel

Cleaners

Never use CHLORIDE or cleaners with bleach to

clean stainless steel.

Clean stainless steel front and handles with non-

abrasive soapy water and a dishcloth. Rinse with

clean water and a soft cloth. Use a non-abrasive

stainless steel cleaner. These cleaners can be

purchased at most home improvement or major

department stores. Always follow manufacturer’s

instructions. Do not use household cleaners

containing ammonia or bleach.

NOTE: Always clean, wipe and dry with the grain

to prevent scratching. Wash the rest of the cabinet

withwarmwaterandmildliquiddetergent.Rinse

well, and wipe dry with a clean soft cloth.

Replacing

Light Bulbs

• Unplug refrigerator

• Wear gloves

• Remove light cover

(some models)

• Replace old bulb

• Replace light cover

(some models)

• Plug in the

refrigerator

CAUTION: Wear gloves when replacing light bulbs

to avoid getting cut. Use same wattage when

replacing bulb

CARE & CLEANING

Page is loading ...

Frigidaire 959924 Owner's manual

Brand: Frigidaire

Model: 959924

Category: Fridge-freezers

Type: Owner's manual

Download PDF

report

Frigidaire 959924 Owner's manual

Frigidaire 959924 Owner's manual

Related papers

Other documents