PEHA Dialog User manual

Brand: PEHA

Model: Dialog

Category: Wall transmitters

Type: User manual

This manual is also suitable for

Surprisingly simple!

– Without wires

– Without batteries

Easyclick radio system

NEW!

As a complement or an alternative to the wall

transmitter: Hand transmitter – up to 4 functions

comfortable in your hand!

System diversity

– without wires, without batteries

No prying open walls, no dirt:

just glue the battery-free wall transmitters on!

With Easyclick PEHA presents a

radio controller without battery and

without connection cables. You re-

ceive an extensive functionality and

unimaginable possibilities of interior

design because the wall transmitters

only have to be glued on!

Therefore a quick and clean assem-

bly without dirt and prying open

walls is guaranteed.

Wall-mounted radio transmitters can

actually reduce the electro-smog load

in the home and the office. Wall-moun-

ted radio transmitters cause approx.

100 times less high frequency emission

than conventional light switches. Low-

frequency pulsed AC is substantially re-

duced thanks to the drastic reduction

of hard wiring and cables inside the

building.

The Easyclick timer: The radio time control with

8 channels and 95 time adjustment possibilities.

A comparative study of the emissions

caused by Easyclick radio signals con-

ducted by the ECOLOG Institute

A convincing answer in building bio-

logy terms, too!

Radio applications for more safety

and comfort

Switch floor

lamps with plug

adapter trans-

mitters via radio

Switch garden

lights comfortably

with a remote

control

Completely shut off

your television or

similar standby devices

Simulate

presence or

activate panic

alarm

Switch and dim

ceiling lamps –

individually or in

groups

Place wall trans-

mitters where you

want them within

seconds

Shade and light settings

can be combined into

illumination situations and

comfortably accessed by

radio

Centrally shut

OFF all light

sources using a

wall transmitter

All these possibilities are either impossible or very elaborate and expensive with conventional

installations. With Easyclick, it is cheaper than you may think!

NEW!

Easyclick radio system

Control sun blinds and

shutters by radio –

individually or in groups

The Baldachin transmitters are pre-wired. This eases

the ceiling mounting.

Afterglow AURA frames – are charged by the surroun-

ding light and release the gathered energy in the dark as

a light source.

The new plug adapter transmitter Plus now offers the

entire functional spectre of the in-wall receiver.

The receivers can be placed out of sight in the

baldachin. Suspended lamps too can be switched

quickly and easily by radio signals.

868 MHz

Typical ranges

Brick walls/Aerated concrete

blocks (ACB)

20 meters through

maximum 3 walls

Unobstructed in large rooms and halls: up to 100 meters

Plaster board/Wood (dry)

30 meters through

maximum 5 walls

Reinforced concrete walls/

Reinforced concrete ceilings

10 meters through

maximum 1 wall/ceiling

Easily control light, shutters and blinds by radio. Or centrally switch ON all lights

if you hear a suspicious noise.

Easyclick is cheaper than you may think! During the renovation or modernisation

of an electro-installation you generally even save money!

Be it a functional building or an office floor – plan flexibly with Easyclick. Main-

tenance-free transmitters are simply attached where you need them.

More comfort due to significantly less electro-smog and less PVC cables in the

walls.

For more safety and comfort

For more flexibility

For more comfort

For more cost saving

Easyclick radio system

Easyclick-timer – the multi-talent

for the Easyclick radio system

A perfect complimentary device for

the Easyclick radio system is the radio

timer in a plug casing. With this trans-

mitter all Easyclick radio receivers can

be controlled or switched using ad-

justable time functions. All entry func-

tions can be easily operated using a

few buttons and are indicated on a

LC-Display. Therefore light or blind

control can be realised automatically

according to preselected times. The

manual operation using buttons on the

radio timer is possible at all times.

Transmitter frequency 868.3 MHz

Number of channels 8

Channels can be designated individually

Number of clock relays 95 clocks

Power reserve in case

of power failure 30 minutes

Protection class IP 20

8 programmable radio channels with

5 channel options respectively for

· Automatic

· Party – 1x intermission of the automatic

· Vacation – random times

· Holidays – Sunday function

· Manual

95 clock relays can be individually

assigned to the radio channels

Automatic adjustment of winter/

summer time, manual adjustment also

possible at all times

Integrated repeater function to increase

the radio distances of further Easyclick

transmitters

NEW!

Plug radio timer into

SCHUKO plug

Illuminated display

large high-contrast display

ESC button

general settings

Select channel option

individual for every channel

Cursor buttons

select channels 1–8

MODE button

set clock relays

Cursor buttons

manual operation of the

receiver

Technical specifications

Easyclick radio system

Radio receiver Easyclick Plus:

This is a Plus you should make use of!

✔ All settings can be saved on

the device at the touch of a

button without needing a

PC or other programming

device

✔ Security functions,

e.g. with window contact

✔ Light scenarios can be

saved and activated by the

user quickly and easily

✔ Flush-mounted socket

receivers with plug-in

terminals and fastening

fixtures for the socket cover

Easyclick uses state-of-the-art techno-

logy: A soft finger touch which crea-

tes an electric impulse is enough –

and this occurs without any power

source! This energy creates a radio

signal on the interference-free 868-

MHz frequency that can activate

various electronic consumers, e.g.

light sources, shutters and blind

motors, etc. The consumers merely

have to be equipped with receivers.

✔ Easy choice of devices,

because one device covers

various applications

✔ Up to 8 functions, integra-

ted with selectable settings

✔ For each transmitter the

function can be selected

on the Plus receiver itself

✔ Flush-mounted socket

receivers with supporting

plate and receptacle for

local operating button

✔ Baldachin receiver with

pre-fitted connections and

hole for ceiling hook

✔ Plug adapter receiver,

e.g. to switch floor lamps by

radio

You can have your Easyclick transmitters learn by means

of the LRN key and you can clear its memory by means

of the CLR key

LRN key

Programming mode

CLR key

Easy radio activation of

receivers with the Easyclick

hand transmitter, 4 channel

Up to 8 programmed functions at

your disposal for each receiver!

Selective ON/OFF with two pushbuttons

ON/OFF with one pushbutton

Staircase lighting function with settable

switching off delay and advance off

warning

Automatic OFF after a settable delay

Sequential pushbutton selection – ON

so long as the pushbutton is pressed

Ventilation function –

Delayed activation and deactivation

Save and activate up to

4 light scenarios at any time at the touch

of a button

Ventilation control with window

monitoring for open lighting points

Dimming with memory function

brighter/darker and ON/OFF with two

pushbuttons

Dimming without memory function

brighter/darker and ON/OFF with two

pushbuttons

Selective ON/OFF/DIM with just one push-

button for easy and convenient operation

Dimming with memory function

brighter/darker and ON/OFF with one

pushbuttons

Staircase lighting function with settable

switching off delay and advance off

warning

Save and activate up to

4 light scenarios at any time at the touch of

a button

UP/STOP/DOWN/louver tilt adjustment

with two pushbuttons

Sun protection with settable motor running

time already integrated for future solutions

Activation of sun protection ON/OFF per

separate wall-mounted transmitter

UP/STOP/DOWN/louver tilt adjustment

with four pushbuttons for easy and

convenient operation

Security function per separate radio

transmitter (maintenance function)

Save and activate up to 4 UP/DOWN

positions at any time at the touch of a

button

1- or 2-channel Easyclick

receiver Plus

1-channel Easyclick

dimmer receiver Plus

Easyclick flush-mounted receiver Plus

for shutters and blinds

Easyclick radio system

System extension for even more

possibilities

Use the in-wall receivers

with support plate in con-

nection with conventional

button fixtures for the local

operation of your receiver!

Here the radio transmitter

is no longer needed – this

means savings with no loss

of functionality!

The switch can be ex-

tended with additional

transmitters.

The new in-wall receivers with support

plate enable you to use a conventio-

nal button fixture instead of a radio trans-

mitter for local operation. That saves

money! Furthermore, setting additional

wall or hand transmitters or setting the

Easyclick-timer is even more comfortable:

Just pull off the button fixture and adjust

the settings! Of course there are new in-

wall receivers with support plate with

the well proven function variety for all

areas: Switching, dimming and as a

blind or shutter control.

✔ Cost-efficient

✔ Comfortable and

easy installation and

programming

✔ Group, central and scena-

rio functions possible

Easyclick 2-level repeater are used

between Easyclick transmitters and

receivers to enhance the range or for

construction specific reasons. In the

1-level operation the radio signal of a

transmitter is received, verified and

sent to the respective receiver with the

maximum transmission power. In the

2-level operation a radio signal can

be sent over an even greater distance

using maximum two repeaters to the

respective receivers – and this without

any configuration effort! The Easy-

click 2-level repeater is available in

the SCHUKO plug casing and as a

in-wall device.

Repeater in the 1-level opera-

tion plug casing or in-wall

Wall-mounted

transmitter

Receiver

Repeater in the 2-level opera-

tion plug casing or in-wall

Wall-mounted

transmitter

ReceiverRepeater in the 2-level opera-

tion plug casing or in-wall

Replace conventional

switches with radio

system

Example shutter control

The system in use

The positioning of wall-mounted transmitters

– flexible and straightforward

A 2-channel wall-mounted transmitter can

be used to switch a light source with two

2 pushbuttons ON and OFF via an Easy-

click 1-channel flush-mounted receiver Plus.

The wall-mounted transmitter can be posi-

tioned just about anywhere and the system

can be extended at any time in the form of

additional wall-mounted transmitters and

the miniature hand-held transmitter.

Easyclick wall-mounted transmitter,

2 channels 20.450.xx FU-BLS

Easyclick flush-mounted receiver Plus

1 channel 451 FU-EP o.T.

Inexpensive switching – with 2 pushbuttons

Using just one 2-channel wall-mounted trans-

mitter it is possible to switch two electrically

powered units (independently of each other)

via an Easyclick 2-channel flush-mounted re-

ceiver Plus. Each pushbutton switches an elec-

trically powered unit ON/OFF/ON.

Easyclick wall-mounted transmitter,

2 channels 20.450.xx FU-BLS

Easyclick flush-mounted receiver Plus

2 channels 452 FU-EP o.T.

User-friendly ON and OFF – without any risk

of confusion

Each of the two pushbuttons on a 2-channel

wall-mounted transmitter performs the same

function; both pushbuttons can thus be used

– without risk of confusion – to switch ON/

OFF/ON via a 1-channel baldachin receiver

in a lamp.

Easyclick wall-mounted transmitter,

2 channels 20.450.xx FU-BLS

Easyclick baldachin receiver Plus

1 channel 451 FU-BEP

Application examples Schematic diagram

ON/OFF/ON

OFF

Easyclick-timer 4514 FU-TS ST

Easyclick flush-mounted receiver Plus

1 channel 451 FU-EP o.T.

Easyclick adapter receiver Plus

4511 FU-EP ST

Easyclick flush-mounted JR receiver Plus,

2 channels 452 FU-EP JR o.T.

Easyclick wall-mounted transmitter,

2 channels 20.450.xx FU-BLS JR

Easyclick window contact 450 FU FK

Switch lights and control blinds with the

Easyclick-timer

This means even more comfort and safety,

because the Easyclick-timer automatically

switches lights and controls blinds with in-

dividually selectable switching times using

the Easyclick receivers. Manual operation

on the Easyclick-timer is also possible

and intelligent additional function such as

party, vacation and holiday functions are

easily set using any radio channel. For the

local blind control a Easyclick wall trans-

mitter is used. Lock out protection for the

terrace door and window contact.

Window contact

Easyclick radio system

Components used

The system in use

Convenient lighting circuits

With just one 4-channel wall-mounted trans-

mitter up to four light scenarios can be acti-

vated. First of all the Easyclick flush-mounted

receivers Plus are individually positioned

according to the associated wall-mounted

transmitters. The light scenario can now be

stored using one of the pushbuttons provided

on the 4-channel wall-mounted transmitter.

Meaningful light scenarios might include, for

example, television, reading, dining, visitors,

frequently used passages through the house,

and many more besides. The UP/DOWN

functions of the shutters receiver can also be

included in the above scenarios. The light

scenarios can of course be adapted at any

time to meet new or modified needs and

situations.

Easyclick wall-mounted transmitter,

2 channels 20.450.xx FU-BLS

(for local operation)

Easyclick wall-mounted transmitter,

4 channels 20.455.xx FU-BLS

(for four light scenarios)

Easyclick flush-mounted receiver Plus

1 channel 451 FU-EP o.T.

Easyclick adapter receiver Plus

4511 FU-EP ST

Easyclick baldachin dimmer receiver Plus,

1 channel 451 FU-BEP DAB

Double button fixture xx.425.xx

Easyclick flush-mounted JR receiver Plus

with support plate 452 FU-EP JR o.A.

Application examples Schematic diagram

Components used

Staircase lighting – switching ON and, after

a settable time and after an advance

warning, switching OFF automatically

This improves safety immensely; before the

light switches off automatically, it flashes a

brief advance warning and if necessary a

wall-mounted transmitter can then be acti-

vated again in good time. The wall-mounted

transmitters can be positioned according to

the user’s real needs, e.g. in spots where you

have always wanted to place a switch, e.g.

to reduce the number of dark zones one has

to cross.

Easyclick wall-mounted transmitter,

2 channels 20.450.xx FU-BLS

alternatively with luminescent frame

20.450.56

Easyclick flush-mounted receiver Plus

1 channel 451 FU-EP o.T.

Easyclick flush-mounted receiver Plus with

support plate

451 FU-EP o.A.

Single button fixture xx.420.xx

Easyclick wall-mounted transmitter,

2 channels 20.450.xx FU-BLS

Refitting of a on/off switch to an alter-

nating switch or a cross connection

For this the on/off switch is replaced with

an Easyclick in-wall receiver Plus with sup-

port plate and a button fixture is attached.

With this the known switch is kept and re-

tains its function. After removing the button

fixture of the Easyclick in-wall receiver the

functions and parameters can easily be

changed due to their easy accessibility.

Additional switch buttons are offered with

Easyclick wall transmitters that are ad-

justed to the receiver and are simply

attached to the wall.

Easyclick radio system

Application examples Schematic diagram

Components used

Security – a ventilation control with window

contact

A window contact can be used to control a

fume extractor hood, via an Easyclick flush-

mounted receiver Plus. If there is a fume extrac-

tor hood and an open fire, e.g. hearth, fire-

place, or stove in the same room, the extractor

can only be activated so long as a window

contact reports “Window OPEN”. This pre-

vents an accumulation of CO in the room

which the open fire might otherwise cause.

The relay contact in the receiver switches ON

as soon as the window contact reports OPEN.

And vice versa the relay resets as soon as all

window contacts report CLOSED. As an

alternative a plug adapter receiver can be

used.

Easyclick window contact 450 FU FK

Easyclick flush-mounted receiver Plus

1 channel451 FU-EP o.T.

Plug adapter receiver Plus switch or dim

with a mini hand transmitter

A battery-free 4 channel hand transmitter

switches or dims floor or table lamps with

one button respectively with a Plus plug

adapter receiver.

These are easily programmable, whereas

additional transmitters can activate ad-

ditional functions – such as automatic

switching off after a selected time.

Naturally the mini hand transmitters can

also be integrated into the other appli-

cation examples.

Easyclick miniature hand-held transmitter,

4 channels 450 FU HS 4

Easyclick adapter receiver Plus

4511 FU-EP ST

Easyclick adapter receiver Plus

4511 FU-EP DAB ST

Easyclick wall-mounted transmitter,

2 channels 20.450.xx FU-BLS

Window contact

Controlling the shutters either individually or

centrally

Two sets of shutters can be controlled via one

Easyclick flush-mounted JR receiver Plus – in-

dividually using two 2-channel wall-mounted

transmitters or, with an additional 2-channel

wall-mounted transmitter, they can be con-

trolled centrally. This control flexibility can be

modified and extended at any time.

Easyclick wall-mounted transmitter,

2 channels 20.450.xx FU-BLS JR

(for local operation)

Easyclick wall-mounted transmitter,

2 channels 20.450.xx FU-BLS JR

(for central operation)

Easyclick flush-mounted JR receiver Plus,

2 channels 452 FU-EP JR o.T.

Set of shutters 1

Set of shutters 2

Group control

Controlling the lighting and ventilation in the

bathroom and guest toilet

With a 2-channel wall-mounted transmitter

the light can be switched on via an Easyclick

2-channel flush-mounted receiver Plus and

after approx. 3 minutes the ventilation can

be switched on too. The ventilation is switched

OFF again automatically after a settable time

from when the light is switched off.

Easyclick wall-mounted transmitter,

2 channels 20.450.xx FU-BLS

Easyclick flush-mounted receiver Plus

2 channels

452 FU-EP o.T. (for light and ventilation)

The system in use

Remote-control switching from a sub-

distribution frame

Four 2-channel wall-mounted transmitters

control a 4-channel flush-mounted series

receiver. In this way four consumer devices

can be switched ON/OFF completely inde-

pendent of one another. This is ideal e.g.

when using flexible distribution frames at

trade fairs or in shop and store systems. The

characteristics of the flush-mounted series

receiver when receiving from the sub-

distribution frame can be improved by using

an aerial.

Easyclick wall-mounted transmitter,

2 channels 20.450.xx FU-BLS

Easyclick flush-mounted series receiver,

4 channels 454 FU-E REG

Aerial 460 ANT

Application examples Schematic diagram

Components used

Switching old and new devices in inter-

mediate ceilings

After renovation work is completed you will,

with a 4-channel flush-mounted ceiling

receiver, be able to switch already existing

and new lights ON/OFF quickly and easily

from the convenience of your desk. Four

2-channel wall-mounted transmitters can

be simply stuck on furniture or glass fittings.

If the room is reassigned to some other

purpose (as often happens with mobile office

partition walls), the installation can be flexibly

modified to meet the new requirements.

Easyclick wall-mounted transmitter,

2 channels 20.450.xx FU-BLS

Easyclick flush-mounted ceiling receiver,

4 channels 454 FU-E DE

The gateway to building services manage-

ment

The Easyclick interface is your link to the world

of PEHA building services control technology.

The Easyclick interface can receive signals

from your wall-mounted and/or miniature

hand-held transmitters, convert these into

telegram form, and sent them to our PHC

building services control system. And vice

versa, the Easyclick interface can receive and

interpret signals from our PHC system and

send these to the Easyclick receivers and

trigger functions at your end. Complex light

switching and shutter control scenarios can

be implemented. To improve the reception

characteristics of the Easyclick interface an

aerial will be needed.

Easyclick interface 941 FU-C

We shall be very pleased to answer any

questions you might have regarding the

numerous possibilities of our PHC system,

PHC Compact, and the components in-

volved.

Busleitung

Easyclick radio system

Article overview

Easyclick wall-mounted transmitter, 2 channels

without combination frame,

rocker switch with neutral mid-position and label I/0, H = 15 mm AURA pure white 20.450.02 FU-BLS 384413

anthracite 20.450.21 FU-BLS 384513

aluminum 20.450.70 FU-BLS 384613

Easyclick wall-mounted transmitter, 4 channels

without combination frame,

series-bridged rocker switch with neutral mid-position and label I/0, H = 15 mm AURA pure white 20.455.02 FU-BLS 385713

anthracite 20.455.21 FU-BLS 385813

aluminum 20.455.70 FU-BLS 385913

Easyclick wall-mounted transmitter, 2 channels, e.g. for one set of shutters

without combination frame,

rocker switch with neutral mid-position and label UP/DOWN, H = 15 mm AURA pure white 20.450.02 FU-BLS JR 384713

anthracite 20.450.21 FU-BLS JR 384813

aluminum 20.450.70 FU-BLS JR 384913

Easyclick wall-mounted transmitter, 4 channels, e.g. for two sets of shutters

without combination frame,

series-bridged rocker switch with neutral mid-position and label UP/DOWN, AURA pure white 20.455.02 FU-BLS JR 386013

H = 15 mm anthracite 20.455.21 FU-BLS JR 386113

aluminum 20.455.70 FU-BLS JR 386313

Easyclick wall-mounted transmitter, neutral, 2 channels

Rocker switch with mid-position, without label AURA pure white 20.450.02 FU-BLS N 130113

anthracite 20.450.21 FU-BLS N 130213

aluminum 20.450.70 FU-BLS N 130313

Easyclick wall-mounted transmitter, neutral, 4 channels

2 rocker switches with mid-position, without label AURA pure white 20.455.02 FU-BLS N 135113

anthracite 20.455.21 FU-BLS N 135213

aluminum 20.455.70 FU-BLS N 135313

Easyclick intermediate frame, green afterglow

for the retrofitting of AURA Easyclick wall transmitters, the intermediate frames can simply yellow/green 20.450.56 130013

be replaced.

Afterglow light crystals (free of any radioctivity) are charged by the surrounding light and

release the gathered energy in the dark as a light source. The best effect is reached with

short wave UV-radiation (Sunlight or light with a high UV percentage).

Reference value: With an illumination of 400 Lux ( medium strong light),

for 20 min with a lamp (norm light type D65) which is similar to daylight, after 12 hours

the afterglow is brighter than the visibility margin of 0,3 mCd/m

in accordance with the

DIN norm.

Easyfit Universal wall transmitter, 2 channels

voor combination frame with inside measurement 55 x 55 mm,

rocker switch with neutral mid-position and label I/0, H = 15 mm pure white 450.02 FU-BLS 320213

anthracite 450.21 FU-BLS 321613

aluminum 450.70 FU-BLS 323013

pure white hg* 450.022 FU-BLS 323413

anthracite hg* 450.212 FU-BLS 324013

Easyfit Universal wall transmitter, 4 channels

voor combination frame with inside measurement 55 x 55 mm,

series-bridged rocker switch with neutral mid-position and label I/0, H = 15 mm pure white 455.02 FU-BLS 320513

anthracite 455.21 FU-BLS 321813

aluminum 455.70 FU-BLS 323213

pure white hg* 455.022 FU-BLS 323713

anthracite hg* 455.212 FU-BLS 324313

*high-gloss

Article designation Colour Article No. Code No.

Easyfit Universal wall transmitter, 2 channels, e.g. for one set of shutters

voor combination frame with inside measurement 55 x 55 mm,

rocker switch with neutral mid-position and label UP/DOWN, H = 15 mm pure white 450.02 FU-BLS JR 320313

anthracite 450.21 FU-BLS JR 321713

aluminum 450.70 FU-BLS JR 323113

pure white hg* 450.022 FU-BLS JR 323513

anthracite hg* 450.212 FU-BLS JR 324113

Easyfit Universal wall transmitter, 4 channels, e.g. for two sets of shutters

voor combination frame with inside measurement 55 x 55 mm,

series-bridged with neutral mid-position and label UP/DOWN, H = 15 mm pure white 455.02 FU-BLS JR 320613

anthracite 455.21 FU-BLS JR 321913

aluminum 455.70 FU-BLS JR 323313

pure white hg* 455.022 FU-BLS JR 323813

anthracite hg* 455.212 FU-BLS JR 324413

Easyfit Universal wall transmitter, 2 channels

voor combination frame with inside measurement 55 x 55 mm,

rocker switch with neutral mid-position, without label, H = 15 mm pure white 450.02 FU-BLS N 320413

anthracite 450.21 FU-BLS N 322013

aluminum 450.70 FU-BLS N 322113

pure white hg* 450.022 FU-BLS N 323613

anthracite hg* 450.212 FU-BLS N 324213

Easyfit Universal wall transmitter, 4 channels

voor combination frame with inside measurement 55 x 55 mm,

series-bridged with neutral mid-position, without label, H = 15 mm pure white 455.02 FU-BLS N 320713

anthracite 455.21 FU-BLS N 322313

aluminum 455.70 FU-BLS N 322413

pure white hg* 455.022 FU-BLS N 323913

anthracite hg* 455.212 FU-BLS N 324513

Advisory note:

Combination frame(s) must be ordered separately.

Easyclick wall-mounted transmitters are also available in STANDARD, DIALOG,

NOVA and in neutral design as well as for the system CONCEPT 45.

Easyclick miniature hand-held transmitter, 4 channels

The Easyclick miniature hand-held transmitter is suitable for the shutters, and for black/grey 450 FU-HS 4 364113

switching and dimming the lights, for raising and lowering the shutters, and for adjusting

the louver tilt of the blinds. It does not need a battery and can be switched irrespective

of position. When you arrive home it lets you conveniently open the garage door and

quickly activate the “welcome back” scenario- all at the touch of a button. The hand-held

transmitter is the remote control specialist; it is small, handy, in a sealed casing, with

4 pushbuttons. For 2-button operation the pushbutton pairs A/B and C/D belong together.

Colours: casing black, pushbuttons grey.

Dimensions: 82 x 50 x 21 mm (L x W x H)

Easyclick-timer in plug casing (SCHUKO), 8 channels

With the Easyclick Timer all Easyclick receivers are controlled and adjustable times are pure white 4514 FU-TS ST 349313

switched using the radio signal. All displays, programmings and operation procedures are

done with a few buttons and the LC-Display.

With this light switching and blind control can be realised automatically with preselected

times.

The Easyclick Timers have 8 programmable radio channels and a maximum of 95 times

can individually be assigned to the radio channels.

Additionally a automatic 1-level repeater function is integrated into the Easyclick Timer.

Easyclick Timer function:

• time controlled automatic operation ON/OFF or UP/DOWN

• manual operation using buttons on the Easyclick Timer ON/OFF or UP/DOWN

• individually adjustable switching times for every radio channel and every day

• automatic adjustment from winter to summer time, manual adjustment also possible

• easy deactivation of switching times with the party function, e.g. blind does not go

DOWN

• vacation switching; with this function the switching is generated randomly with deviation

of max. 15 min. to the programmed times

• with the holiday switching the programmed switching times for Sundays are activated

on holidays

Automatic repeater function:

With the 1-level repeater function the radio signals of other Easyclick transmitters

are received, verified and sent to the respective receiver with the maximum transmission

power.

A configuration is not necessary (e.g. programming the transmitter).

The implementation is done with the simple plugging in to a SCHUKO plug.

A cascading of the Easyclick-timer repeater function with a further

Easyclick Timer or 1-level repeater is not possible.

An additional range increase is possible with the Easyclick 2-level repeater 453 FU-RP ST

or 453 FU-RPP o.T. in 2 level-operation.

IP 20, 230 V, 50 Hz, neutral conductor necessary.

*high-gloss

Article designation Colour Article No. Code No.

Easyclick radio system

Easyclick spare adhesive tape

5 pieces of adhesive tape for Easyclick wall-mounted transmitters AURA and DIALOG,

size: 79 x 79 mm 45 KF 579513

Easyclick flush-mounted receiver Plus with support plate, 1 channel

This Easyclick flush-mounted receiver switches lights and other electrically powered units 451 FU-EP UP o.A. 348013

according to various selectable functions and parameters.

• With support plate for screw attachment in switch sockets with 60 mm distance

to the device screws

• Socket board for the attachment of the button fixture xx.420.xx for switching (local)

Standard function: Button fixture: 1-pushbutton function,

Easyclick transmitter: 2-pushbutton function.

Selectable functions with button fixture: sequential pushbutton function, staircase lighting

function with settable switching off delay and advance OFF warning, automatic off after a

settable delay.

Selectable functions with Easyclick transmitter: 1-pushbutton function, sequential push-

button function, staircase lighting function with settable switching off time and advance

OFF warning, automatic OFF after a settable delay, save and activate 4 light scenarios at

the touch of a button (i.e. for a 4-channel transmitter one light scenario per pushbutton).

One function can be specified individually per transmitter once it has been trained.

Connection data: Filament lamp (ohmic load) 2500 W

High-voltage halogen lamps 1250 W

Electronic ballast 3 pieces

IP 20, 230 V, 50 Hz, neutral conductor required.

Up to a total of 30 transmitters can be trained.

Easyclick flush-mounted receiver Plus, 1 channel

This Easyclick flush-mounted receiver switches lights and other electrically powered units 451 FU-EP o.T. 363113

according to various selectable functions and parameters.

Standard function: 2-pushbutton function.

Selectable functions: 1-pushbutton function, sequential pushbutton selection, staircase

lighting function with settable switching off delay and advance off warning, automatic OFF

after a settable delay, ventilator control with delayed ON and automatic OFF,

4 light scenarios, all can be saved and activated at the touch of a button (one light scenario

per pushbutton), ventilator control with window monitoring.

One function can be specified individually per transmitter once it has been trained.

Connection data: Filament lamp (ohmic load) 2500 W

High-voltage halogen lamps 1250 W

Inductive load 600 VA

Electronic ballast 3 pieces

Height of casing 27 mm, with fastening clips, IP 20, connection via plug-in terminals,

230 V, 50 Hz, neutral conductor required. Up to a total of 30 transmitters can be trained.

Easyclick Plus flush-mounted receiver, 2 channels

The Easyclick flush-mounted receiver, 2 channels (independently programmable) switches 452 FU-EP o.T. 363213

lights and other electrically powered units according to various selectable functions and

parameters per channel. Standard function: 2-pushbutton function

Selectable functions: 1-pushbutton function, sequential pushbutton selection, staircase

lighting function with settable switching off delay and advance off warning, automatic OFF

after a settable delay, ventilator control with delayed ON and automatic OFF, 4 light

scenarios, all can be saved and activated at the touch of a button (one light scenario per

pushbutton), ventilator control with window monitoring. One function can be specified

individually per transmitter once it has been trained.

Connection data per channel: Filament lamp (ohmic load) 500 W

High-voltage halogen lamps 100 W

Inductive load 100 VA

Electronic ballast 1 piece

Height of casing 27 mm, with fastening clips, IP 20, connection via plug-in terminals,

230 V, 50 Hz, neutral conductor required. Up to a total of 30 transmitters can be trained.

Article designation Colour Article No. Code No.

Easyclick flush-mounted JR receiver Plus, 2 channels

The Easyclick flush-mounted receiver controls shutters and blinds according to various 452 FU-EP JR o.T. 363313

selectable functions and parameters.

Standard function: UP/STOP/DOWN with adjustment of louver tilt

Selectable functions: UP/STOP/DOWN without adjustment of louver tilt, sequential push-

button selection for louver tilt, ON/OFF of sun protection function, security function for

blocking the shutters, the sun protection function is already integrated for future solutions,

4 positions UP/DOWN for light scenarios.

One function can be specified individually per transmitter once it has been trained.

Connection data: rated switching capacity (maximum) 600 VA

Height of casing 27 mm, with fastening clips, IP 20, connection via plug-in terminals,

230 V, 50 Hz, neutral conductor required. Up to a total of 30 transmitters can be trained.

Easyclick flush-mounted JR receiver Plus with support plate, 2 channels

The Easyclick flush-mounted receiver controls shutters and blinds according to various 452 FU-EP JR UP o.A. 348113

selectable functions and parameters.

• With support plate for screw attachment in switch sockets with 60 mm distance

to the device screws

• Socket board for the attachment of the button fixture xx.425.xx JR for the control (local)

Standard function: Button fixture: Left button UP, right button DOWN with shutter adjustment,

Easyclick transmitter: 2-pushbutton function UP/DOWN with shutter

adjustment.

Settable functions with button fixture: UP/DOWN with shutter adjustment, touch operation

for shutter adjustment.

Settable functions with Easyclick transmitter: UP/DOWN without louver adjustment,

touch operation for louver adjustment, ON/OFF of sun protection function, sun protection

function for further solution already integrated, safety function to block the blind, 4 position

situations UP/DOWN for light scenarios.

One function can be specified individually per transmitter once it has been trained.

Connection data: 600 VA,

IP 20, 230 V, 50 Hz, neutral conductor required.

Up to a total of 30 transmitters can be trained.

Easyclick baldachin receiver Plus, 1 channel

The Easyclick baldachin receiver switches lights and other electrically powered units 451 FU-BEP 363813

according to various selectable functions and parameters.

Standard function: 2-pushbutton function

Selectable functions: 1-pushbutton function, sequential pushbutton selection, staircase

lighting function with settable switching off delay and advance off warning, automatic

OFF after a settable delay, ventilator control with delayed ON and automatic OFF,

4 light scenarios, all can be saved and activated at the touch of a button (one light

scenario per pushbutton), ventilator control with window monitoring.

One function can be specified individually per transmitter once it has been trained.

Connection data: Filament lamp (ohmic load) 2500 W

High-voltage halogen lamps 1250 W

Inductive load 600 VA

Electronic ballast 3 pieces

Height of casing 27 mm, with screw hook hole, IP 20 , with connection wiring,

230 V, 50 Hz, neutral conductor required. Up to a total of 30 transmitters can be trained.

Easyclick flush-mounted dimmer receiver Plus with support plate, 1 channel

The Easyclick baldachin receiver switches and dims lights according to various selectable 451 FU-EP DAB UP o.A. 348213

functions and parameters.

This dimmer is controlled by trailing-edge phase cut; it is used with low-voltage halogen

lamps with electronic transformer, filament lamps, high-voltage halogen lamps, and other

ohmic loads.

• With support plate for screw attachment in switch sockets with 60 mm distance

to the device screws

• Socket board for the attachment of the button fixture xx.420.xx for switching and

dimming (local)

Standard function: button fixture xx.420.xx: 1-pushbutton function with memory,

Easyclick transmitter: 2-pushbutton function with memory.

Selectable function with button fixture xx.420.xx: 1-pushbutton function without memory

and with settable brightness after switching on, staircase lighting with settable switching

off time and advance OFF warning.

Settable function with Easyclick transmitter: 2-pushbutton function without memory and

with settable brightness after switching on, ON/OFF defined with 2-pushbutton functions,

UP/DOWN/DIM defined with 2-pushbutton functions, 1-pushbutton function with memory,

staircase lighting with settable switching off time and advance OFF warning, save and

activate 4 light scenarios at the touch of a button (i.e. for a 4-channel transmitter one light

scenario per pushbutton).

One function can be specified individually per transmitter once it has been trained.

Connection data: 60 (minimum ) to 210 (maximum) watts (trailing-edge phase),

IP 20, 230 V, 50 Hz, neutral conductor required.

Up to a total of 30 transmitters can be trained.

Article designation Colour Article No. Code No.

Easyclick radio system

Easyclick baldachin dimmer receiver Plus, 1 channel

The Easyclick baldachin receiver switches and dims lights according to various selectable 451 FU-BEP DAB 363913

functions and parameters.

This dimmer is controlled by trailing-edge phase cut; it is used with low-voltage halogen

lamps with electronic transformer, filament lamps, high-voltage halogen lamps, and other

ohmic loads.

Standard function: ON/OFF/dimming, 2-pushbutton function with memory.

Selectable functions: ON/OFF/dimming, 2-pushbutton function without memory,

ON/OFF defined by 2-pushbutton function, dim up/dim down defined by 2-pushbutton

function, ON/OFF/dimming, 1-pushbutton function with memory, staircase lighting

function with settable switching off delay and advance off warning, 4 light scenarios,

all can be saved and activated at the touch of a button (one lighting scenario per push-

button). One function can be specified individually per transmitter once it has been trained.

Connection data: 60 (minimum ) to 250 (maximum) watts

Height of casing 27 mm, with screw hook hole, IP 20, with connection wiring,

230 V, 50 Hz, neutral conductor required. Up to a total of 30 transmitters can be trained.

Button fixture, 1 gang, for Easyclick in-wall receiver with support plate

451 FU-EP UP o.A. and 451 FU-EP DAB UP o.A.

AURA pure white 20.420.02 119113

anthracite 20.420.21 132413

aluminum 20.420.70 158713

Note: The button fixtures can also be delivered in the STANDARD, DIALOG and

NOVA design.

Button fixture, 2 gang, for Easyclick in-wall receiver with support plate,

with lable UP/DOWN 452 FU-EP JR UP o.A.

AURA pure white 20.425.02 JR 132013

anthracite 20.425.21 JR 132113

aluminum 20.425.70 JR 132813

Note: The button fixtures can also be delivered in the STANDARD, DIALOG and

NOVA design.

Easyclick 2-level repeater in plug casing (SCHUKO)

The Easyclick repeater increases the range and therefore the working area between pure white 453 FU-RP ST 349013

Easyclick transmitters and receivers.

In 1-level operation the radio signal of the transmitter is received, verified and sent to the

respective receiver with the maximum transmission power.

In the 2-level operation a radio signal can be sent over an even greater distance using

maximum two repeaters to the respective receivers. A configuration is not necessary for

the repeater (e.g. programming the transmitter).

The implementation is done with the simple plugging in to a SCHUKO plug.

The 1-level operation of the repeater is the standard factory settings and the repeater can

simply be changed to the 2-level operation depending on the project.

IP 20, 230 V, 50 Hz, neutral conductor required.

Easyclick 2-level flush-mounted repeater

The Easyclick repeater increases the range and therefore the working area between 453 FU-RPP o.T. 379513

Easyclick transmitters and receivers.

In 1-level operation the radio signal of the transmitter is received, verified and sent to the

respective receiver with the maximum transmission power.

In the 2-level operation a radio signal can be sent over an even greater distance using

maximum two repeaters to the respective receivers. A configuration is not necessary for

the repeater (e.g. programming the transmitter).

The implementation is done with the simple plugging in to a 230 V,

e.g. a 1960s switch plug.

The 1-level operation of the repeater is the standard factory settings and the repeater can

simply be changed to the 2-level operation depending on the project.

IP 20, 230 V, 50 Hz, neutral conductor required.

Easyclick window contact

This door/window contact monitors the status of doors and windows, it does not need a 450 FU FK 367113

battery, it is operated by Easyclick radio signals via the Easyclick Plus receiver.

The Easyclick window contact is wireless and completely maintenance-free, it incorporates

an internal solar-powered energy store. It continues to operate through dark spells lasting

several days. Signal transmission is immediate, as soon as a window opens or closes, it is

triggered by a window magnet. The window contact can be fitted to all the usual frame

profiles. Thanks to its wireless radio transmission the window contact is ideal for installing

in existing buildings in order to improve security. It is compatible with the Easyclick Plus

receiver and the PHC system. Colour similar to RAL 9003, protection IP 40,

dimensions of the window contact: 110 x 19 x 15 mm (L x W x H),

dimensions of the magnet: 23 x 14 x 6 mm (L x W xH).

Article designation Colour Article No. Code No.

Cover for flush-mounted receiver

Cover for Easyclick flush-mounted receiver and Easyclick flush-mounted repeater,

other colors available on request. AURA pure white 20.477.02 372613

Easyclick adapter receiver (SCHUKO) Plus, 1 channel (SCHUKO)

Easyclick plug adapter receivers for switching of lights and other electronic consumers pure white 4511 FU-EP ST 349113

with regard to different settable functions and parameters.

Standard function: 2-pushbutton function.

Selectable functions: 1-pushbutton function, sequential pushbutton function,

staircase lighting function with settable switching off delay and advance OFF warning,

automatic OFF after a settable delay, ventilator control function with delayed ON and

automatic switching off, save and activate 4 light scenarios at the touch of a button

(i.e. for a 4-channel transmitter one light scenario per pushbutton),

ventilator control function with window monitoring.

One function can be specified individually per transmitter once it has been trained.

Connection data: Filament lamp (ohmic load) 2500 W

High-voltage halogen lamps 1250W

Electronic ballast 3 pieces

IP 20, 230 V, 50 Hz, neutral conductor required. Up to a total of 32 transmitters

can be trained.

Plug adapter version in preparation: with earthing pin 4571 FU-EP ST 349613

to Swiss standard (SEV) (Schweizerischer Elektrotechnischer Verein) 4571 FU-EP ST CH 349713

in accordance with British norm 4571 FU-EP ST GB 349913

Easyclick adapter dimmer receiver (SCHUKO) Plus, 1 channel (SCHUKO)

Easyclick plug adapter receivers switches and dims lights with regard to different settable pure white 4511 FU-EP DAB ST 349213

functions and parameters.

This dimmer is controlled by trailing-edge phase cut; it is used with low-voltage halogen

lamps with electronic transformer, filament lamps, high-voltage halogen lamps, and other

ohmic loads.

Standard function: ON/OFF/dimming, 2-pushbutton function with memory.

Selectable functions: ON/OFF/dimming, 2-pushbutton function without memory and

with settable brightness after switching on, ON/OFF defined with 2-pushbutton functions,

UP/DOWN/DIM defined with 2-pushbutton functions, 1-pushbutton function with memory,

staircase lighting with settable switching off time and advance OFF warning, save and

activate 4 light scenarios at the touch of a button (i.e. for a 4-channel transmitter one light

scenario per pushbutton).

One function can be specified individually per transmitter once it has been trained.

The plug adapter has a protection function for unsuited kinds of load and switches OFF

automatically.

Connection data: 60 (minimum ) to 420 (maximum) watts (trailing-edge phase cut),

IP 20, 230 V, 50 Hz, neutral conductor required. Up to a total of 32 transmitters

can be trained.

Plug adapter version in preparation: with earthing pin 4571 FU-EP DAB ST 345413

to Swiss standard (SEV) (Schweizerischer Elektrotechnischer Verein) 4571 FU-EP DAB ST CH 345513

in accordance with British norm 4571 FU-EP DAB ST GB 345613

Easyclick flush-mounted ceiling receiver

4-channel switching module, with two pushbuttons, each with ON/OFF function. 454 FU-E DE 380113

30 Easyclick transmitters can be trained to work with one receiver.

Connection options: 3 push-to-make switches and 1 changeover contact (zero-potential

and independently programmable), dimensions: 230 x 55 x 36 mm (LxWxH)

Supply voltage 230 V, 50 Hz, neutral conductor required, screw terminals,

the contacts must not be operated with mixed voltages (i.e. safety extra-low voltage

and 230 V).

Connection data for electrically powered units

per channel: push-to-make (PTM) push-to-break (PTB)

Filament lamp (ohmic load) 2500 W 1000 W

High-voltage halogen lamps 1250 W 500 W

Inductive load 600 VA 250 W

Electronic ballast 3 pieces 1 piece

Article designation Colour Article No. Code No.

Page is loading ...

PEHA Dialog User manual

Brand: PEHA

Model: Dialog

Category: Wall transmitters

Type: User manual

This manual is also suitable for

Download PDF

report

PEHA Dialog User manual

This manual is also suitable for

PEHA Dialog User manual

Related papers

Other documents