PEHA AURA User manual

Category
Wall transmitters
Type
User manual

This manual is also suitable for

Surprisingly simple!
– Without wires
– Without batteries
Easyclick radio system
NEW!
As a complement or an alternative to the wall
transmitter: Hand transmitter – up to 4 functions
comfortable in your hand!
System diversity
– without wires, without batteries
No prying open walls, no dirt:
just glue the battery-free wall transmitters on!
With Easyclick PEHA presents a
radio controller without battery and
without connection cables. You re-
ceive an extensive functionality and
unimaginable possibilities of interior
design because the wall transmitters
only have to be glued on!
Therefore a quick and clean assem-
bly without dirt and prying open
walls is guaranteed.
Wall-mounted radio transmitters can
actually reduce the electro-smog load
in the home and the office. Wall-moun-
ted radio transmitters cause approx.
100 times less high frequency emission
than conventional light switches. Low-
frequency pulsed AC is substantially re-
duced thanks to the drastic reduction
of hard wiring and cables inside the
building.
The Easyclick timer: The radio time control with
8 channels and 95 time adjustment possibilities.
A comparative study of the emissions
caused by Easyclick radio signals con-
ducted by the ECOLOG Institute
A convincing answer in building bio-
logy terms, too!
Radio applications for more safety
and comfort
Switch floor
lamps with plug
adapter trans-
mitters via radio
Switch garden
lights comfortably
with a remote
control
Completely shut off
your television or
similar standby devices
Simulate
presence or
activate panic
alarm
Switch and dim
ceiling lamps –
individually or in
groups
Place wall trans-
mitters where you
want them within
seconds
Shade and light settings
can be combined into
illumination situations and
comfortably accessed by
radio
Centrally shut
OFF all light
sources using a
wall transmitter
All these possibilities are either impossible or very elaborate and expensive with conventional
installations. With Easyclick, it is cheaper than you may think!
NEW!
NEW!
Easyclick radio system
Control sun blinds and
shutters by radio –
individually or in groups
The Baldachin transmitters are pre-wired. This eases
the ceiling mounting.
Afterglow AURA frames are charged by the surroun-
ding light and release the gathered energy in the dark as
a light source.
The new plug adapter transmitter Plus now offers the
entire functional spectre of the in-wall receiver.
The receivers can be placed out of sight in the
baldachin. Suspended lamps too can be switched
quickly and easily by radio signals.
868 MHz
Typical ranges
Brick walls/Aerated concrete
blocks (ACB)
20 meters through
maximum 3 walls
Unobstructed in large rooms and halls: up to 100 meters
Plaster board/Wood (dry)
30 meters through
maximum 5 walls
Reinforced concrete walls/
Reinforced concrete ceilings
10 meters through
maximum 1 wall/ceiling
Easily control light, shutters and blinds by radio. Or centrally switch ON all lights
if you hear a suspicious noise.
Easyclick is cheaper than you may think! During the renovation or modernisation
of an electro-installation you generally even save money!
Be it a functional building or an office floor – plan flexibly with Easyclick. Main-
tenance-free transmitters are simply attached where you need them.
More comfort due to significantly less electro-smog and less PVC cables in the
walls.
For more safety and comfort
For more flexibility
For more comfort
For more cost saving
Easyclick radio system
Easyclick-timer – the multi-talent
for the Easyclick radio system
A perfect complimentary device for
the Easyclick radio system is the radio
timer in a plug casing. With this trans-
mitter all Easyclick radio receivers can
be controlled or switched using ad-
justable time functions. All entry func-
tions can be easily operated using a
few buttons and are indicated on a
LC-Display. Therefore light or blind
control can be realised automatically
according to preselected times. The
manual operation using buttons on the
radio timer is possible at all times.
Transmitter frequency 868.3 MHz
Number of channels 8
Channels can be designated individually
Number of clock relays 95 clocks
Power reserve in case
of power failure 30 minutes
Protection class IP 20
8 programmable radio channels with
5 channel options respectively for
· Automatic
· Party – 1x intermission of the automatic
· Vacation – random times
· Holidays – Sunday function
· Manual
95 clock relays can be individually
assigned to the radio channels
Automatic adjustment of winter/
summer time, manual adjustment also
possible at all times
Integrated repeater function to increase
the radio distances of further Easyclick
transmitters
NEW!
Plug radio timer into
SCHUKO plug
Illuminated display
large high-contrast display
ESC button
general settings
Select channel option
individual for every channel
Cursor buttons
select channels 1–8
MODE button
set clock relays
Cursor buttons
manual operation of the
receiver
Technical specifications
Easyclick radio system
Radio receiver Easyclick Plus:
This is a Plus you should make use of!
All settings can be saved on
the device at the touch of a
button without needing a
PC or other programming
device
Security functions,
e.g. with window contact
Light scenarios can be
saved and activated by the
user quickly and easily
Flush-mounted socket
receivers with plug-in
terminals and fastening
fixtures for the socket cover
Easyclick uses state-of-the-art techno-
logy: A soft finger touch which crea-
tes an electric impulse is enough –
and this occurs without any power
source! This energy creates a radio
signal on the interference-free 868-
MHz frequency that can activate
various electronic consumers, e.g.
light sources, shutters and blind
motors, etc. The consumers merely
have to be equipped with receivers.
Easy choice of devices,
because one device covers
various applications
Up to 8 functions, integra-
ted with selectable settings
For each transmitter the
function can be selected
on the Plus receiver itself
Flush-mounted socket
receivers with supporting
plate and receptacle for
local operating button
Baldachin receiver with
pre-fitted connections and
hole for ceiling hook
Plug adapter receiver,
e.g. to switch floor lamps by
radio
You can have your Easyclick transmitters learn by means
of the LRN key and you can clear its memory by means
of the CLR key
LRN key
Programming mode
CLR key
Easy radio activation of
receivers with the Easyclick
hand transmitter, 4 channel
Up to 8 programmed functions at
your disposal for each receiver!
Selective ON/OFF with two pushbuttons
ON/OFF with one pushbutton
Staircase lighting function with settable
switching off delay and advance off
warning
Automatic OFF after a settable delay
Sequential pushbutton selection – ON
so long as the pushbutton is pressed
Ventilation function –
Delayed activation and deactivation
Save and activate up to
4 light scenarios at any time at the touch
of a button
Ventilation control with window
monitoring for open lighting points
Dimming with memory function
brighter/darker and ON/OFF with two
pushbuttons
Dimming without memory function
brighter/darker and ON/OFF with two
pushbuttons
Selective ON/OFF/DIM with just one push-
button for easy and convenient operation
Dimming with memory function
brighter/darker and ON/OFF with one
pushbuttons
Staircase lighting function with settable
switching off delay and advance off
warning
Save and activate up to
4 light scenarios at any time at the touch of
a button
UP/STOP/DOWN/louver tilt adjustment
with two pushbuttons
Sun protection with settable motor running
time already integrated for future solutions
Activation of sun protection ON/OFF per
separate wall-mounted transmitter
UP/STOP/DOWN/louver tilt adjustment
with four pushbuttons for easy and
convenient operation
Security function per separate radio
transmitter (maintenance function)
Save and activate up to 4 UP/DOWN
positions at any time at the touch of a
button
1- or 2-channel Easyclick
receiver Plus
1-channel Easyclick
dimmer receiver Plus
Easyclick flush-mounted receiver Plus
for shutters and blinds
Easyclick radio system
System extension for even more
possibilities
Use the in-wall receivers
with support plate in con-
nection with conventional
button fixtures for the local
operation of your receiver!
Here the radio transmitter
is no longer needed – this
means savings with no loss
of functionality!
The switch can be ex-
tended with additional
transmitters.
The new in-wall receivers with support
plate enable you to use a conventio-
nal button fixture instead of a radio trans-
mitter for local operation. That saves
money! Furthermore, setting additional
wall or hand transmitters or setting the
Easyclick-timer is even more comfortable:
Just pull off the button fixture and adjust
the settings! Of course there are new in-
wall receivers with support plate with
the well proven function variety for all
areas: Switching, dimming and as a
blind or shutter control.
Cost-efficient
Comfortable and
easy installation and
programming
Group, central and scena-
rio functions possible
Easyclick 2-level repeater are used
between Easyclick transmitters and
receivers to enhance the range or for
construction specific reasons. In the
1-level operation the radio signal of a
transmitter is received, verified and
sent to the respective receiver with the
maximum transmission power. In the
2-level operation a radio signal can
be sent over an even greater distance
using maximum two repeaters to the
respective receivers – and this without
any configuration effort! The Easy-
click 2-level repeater is available in
the SCHUKO plug casing and as a
in-wall device.
Repeater in the 1-level opera-
tion plug casing or in-wall
Wall-mounted
transmitter
Receiver
Repeater in the 2-level opera-
tion plug casing or in-wall
Wall-mounted
transmitter
ReceiverRepeater in the 2-level opera-
tion plug casing or in-wall
Replace conventional
switches with radio
system
Example shutter control
The system in use
The positioning of wall-mounted transmitters
– flexible and straightforward
A 2-channel wall-mounted transmitter can
be used to switch a light source with two
2 pushbuttons ON and OFF via an Easy-
click 1-channel flush-mounted receiver Plus.
The wall-mounted transmitter can be posi-
tioned just about anywhere and the system
can be extended at any time in the form of
additional wall-mounted transmitters and
the miniature hand-held transmitter.
Easyclick wall-mounted transmitter,
2 channels 20.450.xx FU-BLS
Easyclick flush-mounted receiver Plus
1 channel 451 FU-EP o.T.
Inexpensive switching – with 2 pushbuttons
Using just one 2-channel wall-mounted trans-
mitter it is possible to switch two electrically
powered units (independently of each other)
via an Easyclick 2-channel flush-mounted re-
ceiver Plus. Each pushbutton switches an elec-
trically powered unit ON/OFF/ON.
Easyclick wall-mounted transmitter,
2 channels 20.450.xx FU-BLS
Easyclick flush-mounted receiver Plus
2 channels 452 FU-EP o.T.
User-friendly ON and OFF – without any risk
of confusion
Each of the two pushbuttons on a 2-channel
wall-mounted transmitter performs the same
function; both pushbuttons can thus be used
– without risk of confusion – to switch ON/
OFF/ON via a 1-channel baldachin receiver
in a lamp.
Easyclick wall-mounted transmitter,
2 channels 20.450.xx FU-BLS
Easyclick baldachin receiver Plus
1 channel 451 FU-BEP
Application examples Schematic diagram
ON
ON/OFF/ON
ON/OFF/ON
ON/OFF/ON
ON/OFF/ON
OFF
Easyclick-timer 4514 FU-TS ST
Easyclick flush-mounted receiver Plus
1 channel 451 FU-EP o.T.
Easyclick adapter receiver Plus
4511 FU-EP ST
Easyclick flush-mounted JR receiver Plus,
2 channels 452 FU-EP JR o.T.
Easyclick wall-mounted transmitter,
2 channels 20.450.xx FU-BLS JR
Easyclick window contact 450 FU FK
Switch lights and control blinds with the
Easyclick-timer
This means even more comfort and safety,
because the Easyclick-timer automatically
switches lights and controls blinds with in-
dividually selectable switching times using
the Easyclick receivers. Manual operation
on the Easyclick-timer is also possible
and intelligent additional function such as
party, vacation and holiday functions are
easily set using any radio channel. For the
local blind control a Easyclick wall trans-
mitter is used. Lock out protection for the
terrace door and window contact.
Window contact
Easyclick radio system
Components used
The system in use
Convenient lighting circuits
With just one 4-channel wall-mounted trans-
mitter up to four light scenarios can be acti-
vated. First of all the Easyclick flush-mounted
receivers Plus are individually positioned
according to the associated wall-mounted
transmitters. The light scenario can now be
stored using one of the pushbuttons provided
on the 4-channel wall-mounted transmitter.
Meaningful light scenarios might include, for
example, television, reading, dining, visitors,
frequently used passages through the house,
and many more besides. The UP/DOWN
functions of the shutters receiver can also be
included in the above scenarios. The light
scenarios can of course be adapted at any
time to meet new or modified needs and
situations.
Easyclick wall-mounted transmitter,
2 channels 20.450.xx FU-BLS
(for local operation)
Easyclick wall-mounted transmitter,
4 channels 20.455.xx FU-BLS
(for four light scenarios)
Easyclick flush-mounted receiver Plus
1 channel 451 FU-EP o.T.
Easyclick adapter receiver Plus
4511 FU-EP ST
Easyclick baldachin dimmer receiver Plus,
1 channel 451 FU-BEP DAB
Double button fixture xx.425.xx
Easyclick flush-mounted JR receiver Plus
with support plate 452 FU-EP JR o.A.
Application examples Schematic diagram
Components used
Staircase lighting – switching ON and, after
a settable time and after an advance
warning, switching OFF automatically
This improves safety immensely; before the
light switches off automatically, it flashes a
brief advance warning and if necessary a
wall-mounted transmitter can then be acti-
vated again in good time. The wall-mounted
transmitters can be positioned according to
the user’s real needs, e.g. in spots where you
have always wanted to place a switch, e.g.
to reduce the number of dark zones one has
to cross.
Easyclick wall-mounted transmitter,
2 channels 20.450.xx FU-BLS
alternatively with luminescent frame
20.450.56
Easyclick flush-mounted receiver Plus
1 channel 451 FU-EP o.T.
Easyclick flush-mounted receiver Plus with
support plate
451 FU-EP o.A.
Single button fixture xx.420.xx
Easyclick wall-mounted transmitter,
2 channels 20.450.xx FU-BLS
Refitting of a on/off switch to an alter-
nating switch or a cross connection
For this the on/off switch is replaced with
an Easyclick in-wall receiver Plus with sup-
port plate and a button fixture is attached.
With this the known switch is kept and re-
tains its function. After removing the button
fixture of the Easyclick in-wall receiver the
functions and parameters can easily be
changed due to their easy accessibility.
Additional switch buttons are offered with
Easyclick wall transmitters that are ad-
justed to the receiver and are simply
attached to the wall.
Easyclick radio system
Application examples Schematic diagram
Components used
Security – a ventilation control with window
contact
A window contact can be used to control a
fume extractor hood, via an Easyclick flush-
mounted receiver Plus. If there is a fume extrac-
tor hood and an open fire, e.g. hearth, fire-
place, or stove in the same room, the extractor
can only be activated so long as a window
contact reports “Window OPEN”. This pre-
vents an accumulation of CO in the room
which the open fire might otherwise cause.
The relay contact in the receiver switches ON
as soon as the window contact reports OPEN.
And vice versa the relay resets as soon as all
window contacts report CLOSED. As an
alternative a plug adapter receiver can be
used.
Easyclick window contact 450 FU FK
Easyclick flush-mounted receiver Plus
1 channel451 FU-EP o.T.
Plug adapter receiver Plus switch or dim
with a mini hand transmitter
A battery-free 4 channel hand transmitter
switches or dims floor or table lamps with
one button respectively with a Plus plug
adapter receiver.
These are easily programmable, whereas
additional transmitters can activate ad-
ditional functions – such as automatic
switching off after a selected time.
Naturally the mini hand transmitters can
also be integrated into the other appli-
cation examples.
Easyclick miniature hand-held transmitter,
4 channels 450 FU HS 4
Easyclick adapter receiver Plus
4511 FU-EP ST
Easyclick adapter receiver Plus
4511 FU-EP DAB ST
Easyclick wall-mounted transmitter,
2 channels 20.450.xx FU-BLS
Window contact
Controlling the shutters either individually or
centrally
Two sets of shutters can be controlled via one
Easyclick flush-mounted JR receiver Plus – in-
dividually using two 2-channel wall-mounted
transmitters or, with an additional 2-channel
wall-mounted transmitter, they can be con-
trolled centrally. This control flexibility can be
modified and extended at any time.
Easyclick wall-mounted transmitter,
2 channels 20.450.xx FU-BLS JR
(for local operation)
Easyclick wall-mounted transmitter,
2 channels 20.450.xx FU-BLS JR
(for central operation)
Easyclick flush-mounted JR receiver Plus,
2 channels 452 FU-EP JR o.T.
Set of shutters 1
Set of shutters 2
Group control
Controlling the lighting and ventilation in the
bathroom and guest toilet
With a 2-channel wall-mounted transmitter
the light can be switched on via an Easyclick
2-channel flush-mounted receiver Plus and
after approx. 3 minutes the ventilation can
be switched on too. The ventilation is switched
OFF again automatically after a settable time
from when the light is switched off.
Easyclick wall-mounted transmitter,
2 channels 20.450.xx FU-BLS
Easyclick flush-mounted receiver Plus
2 channels
452 FU-EP o.T. (for light and ventilation)
The system in use
Remote-control switching from a sub-
distribution frame
Four 2-channel wall-mounted transmitters
control a 4-channel flush-mounted series
receiver. In this way four consumer devices
can be switched ON/OFF completely inde-
pendent of one another. This is ideal e.g.
when using flexible distribution frames at
trade fairs or in shop and store systems. The
characteristics of the flush-mounted series
receiver when receiving from the sub-
distribution frame can be improved by using
an aerial.
Easyclick wall-mounted transmitter,
2 channels 20.450.xx FU-BLS
Easyclick flush-mounted series receiver,
4 channels 454 FU-E REG
Aerial 460 ANT
Application examples Schematic diagram
Components used
Switching old and new devices in inter-
mediate ceilings
After renovation work is completed you will,
with a 4-channel flush-mounted ceiling
receiver, be able to switch already existing
and new lights ON/OFF quickly and easily
from the convenience of your desk. Four
2-channel wall-mounted transmitters can
be simply stuck on furniture or glass fittings.
If the room is reassigned to some other
purpose (as often happens with mobile office
partition walls), the installation can be flexibly
modified to meet the new requirements.
Easyclick wall-mounted transmitter,
2 channels 20.450.xx FU-BLS
Easyclick flush-mounted ceiling receiver,
4 channels 454 FU-E DE
The gateway to building services manage-
ment
The Easyclick interface is your link to the world
of PEHA building services control technology.
The Easyclick interface can receive signals
from your wall-mounted and/or miniature
hand-held transmitters, convert these into
telegram form, and sent them to our PHC
building services control system. And vice
versa, the Easyclick interface can receive and
interpret signals from our PHC system and
send these to the Easyclick receivers and
trigger functions at your end. Complex light
switching and shutter control scenarios can
be implemented. To improve the reception
characteristics of the Easyclick interface an
aerial will be needed.
Easyclick interface 941 FU-C
We shall be very pleased to answer any
questions you might have regarding the
numerous possibilities of our PHC system,
PHC Compact, and the components in-
volved.
Busleitung
Easyclick radio system
Article overview
Easyclick wall-mounted transmitter, 2 channels
without combination frame,
rocker switch with neutral mid-position and label I/0, H = 15 mm AURA pure white 20.450.02 FU-BLS 384413
anthracite 20.450.21 FU-BLS 384513
aluminum 20.450.70 FU-BLS 384613
Easyclick wall-mounted transmitter, 4 channels
without combination frame,
series-bridged rocker switch with neutral mid-position and label I/0, H = 15 mm AURA pure white 20.455.02 FU-BLS 385713
anthracite 20.455.21 FU-BLS 385813
aluminum 20.455.70 FU-BLS 385913
Easyclick wall-mounted transmitter, 2 channels, e.g. for one set of shutters
without combination frame,
rocker switch with neutral mid-position and label UP/DOWN, H = 15 mm AURA pure white 20.450.02 FU-BLS JR 384713
anthracite 20.450.21 FU-BLS JR 384813
aluminum 20.450.70 FU-BLS JR 384913
Easyclick wall-mounted transmitter, 4 channels, e.g. for two sets of shutters
without combination frame,
series-bridged rocker switch with neutral mid-position and label UP/DOWN, AURA pure white 20.455.02 FU-BLS JR 386013
H = 15 mm anthracite 20.455.21 FU-BLS JR 386113
aluminum 20.455.70 FU-BLS JR 386313
Easyclick wall-mounted transmitter, neutral, 2 channels
Rocker switch with mid-position, without label AURA pure white 20.450.02 FU-BLS N 130113
anthracite 20.450.21 FU-BLS N 130213
aluminum 20.450.70 FU-BLS N 130313
Easyclick wall-mounted transmitter, neutral, 4 channels
2 rocker switches with mid-position, without label AURA pure white 20.455.02 FU-BLS N 135113
anthracite 20.455.21 FU-BLS N 135213
aluminum 20.455.70 FU-BLS N 135313
Easyclick intermediate frame, green afterglow
for the retrofitting of AURA Easyclick wall transmitters, the intermediate frames can simply yellow/green 20.450.56 130013
be replaced.
Afterglow light crystals (free of any radioctivity) are charged by the surrounding light and
release the gathered energy in the dark as a light source. The best effect is reached with
short wave UV-radiation (Sunlight or light with a high UV percentage).
Reference value: With an illumination of 400 Lux ( medium strong light),
for 20 min with a lamp (norm light type D65) which is similar to daylight, after 12 hours
the afterglow is brighter than the visibility margin of 0,3 mCd/m
2
in accordance with the
DIN norm.
Easyfit Universal wall transmitter, 2 channels
voor combination frame with inside measurement 55 x 55 mm,
rocker switch with neutral mid-position and label I/0, H = 15 mm pure white 450.02 FU-BLS 320213
anthracite 450.21 FU-BLS 321613
aluminum 450.70 FU-BLS 323013
pure white hg* 450.022 FU-BLS 323413
anthracite hg* 450.212 FU-BLS 324013
Easyfit Universal wall transmitter, 4 channels
voor combination frame with inside measurement 55 x 55 mm,
series-bridged rocker switch with neutral mid-position and label I/0, H = 15 mm pure white 455.02 FU-BLS 320513
anthracite 455.21 FU-BLS 321813
aluminum 455.70 FU-BLS 323213
pure white hg* 455.022 FU-BLS 323713
anthracite hg* 455.212 FU-BLS 324313
*high-gloss
Article designation Colour Article No. Code No.
Easyfit Universal wall transmitter, 2 channels, e.g. for one set of shutters
voor combination frame with inside measurement 55 x 55 mm,
rocker switch with neutral mid-position and label UP/DOWN, H = 15 mm pure white 450.02 FU-BLS JR 320313
anthracite 450.21 FU-BLS JR 321713
aluminum 450.70 FU-BLS JR 323113
pure white hg* 450.022 FU-BLS JR 323513
anthracite hg* 450.212 FU-BLS JR 324113
Easyfit Universal wall transmitter, 4 channels, e.g. for two sets of shutters
voor combination frame with inside measurement 55 x 55 mm,
series-bridged with neutral mid-position and label UP/DOWN, H = 15 mm pure white 455.02 FU-BLS JR 320613
anthracite 455.21 FU-BLS JR 321913
aluminum 455.70 FU-BLS JR 323313
pure white hg* 455.022 FU-BLS JR 323813
anthracite hg* 455.212 FU-BLS JR 324413
Easyfit Universal wall transmitter, 2 channels
voor combination frame with inside measurement 55 x 55 mm,
rocker switch with neutral mid-position, without label, H = 15 mm pure white 450.02 FU-BLS N 320413
anthracite 450.21 FU-BLS N 322013
aluminum 450.70 FU-BLS N 322113
pure white hg* 450.022 FU-BLS N 323613
anthracite hg* 450.212 FU-BLS N 324213
Easyfit Universal wall transmitter, 4 channels
voor combination frame with inside measurement 55 x 55 mm,
series-bridged with neutral mid-position, without label, H = 15 mm pure white 455.02 FU-BLS N 320713
anthracite 455.21 FU-BLS N 322313
aluminum 455.70 FU-BLS N 322413
pure white hg* 455.022 FU-BLS N 323913
anthracite hg* 455.212 FU-BLS N 324513
Advisory note:
Combination frame(s) must be ordered separately.
Easyclick wall-mounted transmitters are also available in STANDARD, DIALOG,
NOVA and in neutral design as well as for the system CONCEPT 45.
Easyclick miniature hand-held transmitter, 4 channels
The Easyclick miniature hand-held transmitter is suitable for the shutters, and for black/grey 450 FU-HS 4 364113
switching and dimming the lights, for raising and lowering the shutters, and for adjusting
the louver tilt of the blinds. It does not need a battery and can be switched irrespective
of position. When you arrive home it lets you conveniently open the garage door and
quickly activate the “welcome back” scenario- all at the touch of a button. The hand-held
transmitter is the remote control specialist; it is small, handy, in a sealed casing, with
4 pushbuttons. For 2-button operation the pushbutton pairs A/B and C/D belong together.
Colours: casing black, pushbuttons grey.
Dimensions: 82 x 50 x 21 mm (L x W x H)
Easyclick-timer in plug casing (SCHUKO), 8 channels
With the Easyclick Timer all Easyclick receivers are controlled and adjustable times are pure white 4514 FU-TS ST 349313
switched using the radio signal. All displays, programmings and operation procedures are
done with a few buttons and the LC-Display.
With this light switching and blind control can be realised automatically with preselected
times.
The Easyclick Timers have 8 programmable radio channels and a maximum of 95 times
can individually be assigned to the radio channels.
Additionally a automatic 1-level repeater function is integrated into the Easyclick Timer.
Easyclick Timer function:
• time controlled automatic operation ON/OFF or UP/DOWN
• manual operation using buttons on the Easyclick Timer ON/OFF or UP/DOWN
• individually adjustable switching times for every radio channel and every day
• automatic adjustment from winter to summer time, manual adjustment also possible
• easy deactivation of switching times with the party function, e.g. blind does not go
DOWN
• vacation switching; with this function the switching is generated randomly with deviation
of max. 15 min. to the programmed times
• with the holiday switching the programmed switching times for Sundays are activated
on holidays
Automatic repeater function:
With the 1-level repeater function the radio signals of other Easyclick transmitters
are received, verified and sent to the respective receiver with the maximum transmission
power.
A configuration is not necessary (e.g. programming the transmitter).
The implementation is done with the simple plugging in to a SCHUKO plug.
A cascading of the Easyclick-timer repeater function with a further
Easyclick Timer or 1-level repeater is not possible.
An additional range increase is possible with the Easyclick 2-level repeater 453 FU-RP ST
or 453 FU-RPP o.T. in 2 level-operation.
IP 20, 230 V, 50 Hz, neutral conductor necessary.
*high-gloss
Article designation Colour Article No. Code No.
Easyclick radio system
Easyclick spare adhesive tape
5 pieces of adhesive tape for Easyclick wall-mounted transmitters AURA and DIALOG,
size: 79 x 79 mm 45 KF 579513
Easyclick flush-mounted receiver Plus with support plate, 1 channel
This Easyclick flush-mounted receiver switches lights and other electrically powered units 451 FU-EP UP o.A. 348013
according to various selectable functions and parameters.
• With support plate for screw attachment in switch sockets with 60 mm distance
to the device screws
• Socket board for the attachment of the button fixture xx.420.xx for switching (local)
Standard function: Button fixture: 1-pushbutton function,
Easyclick transmitter: 2-pushbutton function.
Selectable functions with button fixture: sequential pushbutton function, staircase lighting
function with settable switching off delay and advance OFF warning, automatic off after a
settable delay.
Selectable functions with Easyclick transmitter: 1-pushbutton function, sequential push-
button function, staircase lighting function with settable switching off time and advance
OFF warning, automatic OFF after a settable delay, save and activate 4 light scenarios at
the touch of a button (i.e. for a 4-channel transmitter one light scenario per pushbutton).
One function can be specified individually per transmitter once it has been trained.
Connection data: Filament lamp (ohmic load) 2500 W
High-voltage halogen lamps 1250 W
Electronic ballast 3 pieces
IP 20, 230 V, 50 Hz, neutral conductor required.
Up to a total of 30 transmitters can be trained.
Easyclick flush-mounted receiver Plus, 1 channel
This Easyclick flush-mounted receiver switches lights and other electrically powered units 451 FU-EP o.T. 363113
according to various selectable functions and parameters.
Standard function: 2-pushbutton function.
Selectable functions: 1-pushbutton function, sequential pushbutton selection, staircase
lighting function with settable switching off delay and advance off warning, automatic OFF
after a settable delay, ventilator control with delayed ON and automatic OFF,
4 light scenarios, all can be saved and activated at the touch of a button (one light scenario
per pushbutton), ventilator control with window monitoring.
One function can be specified individually per transmitter once it has been trained.
Connection data: Filament lamp (ohmic load) 2500 W
High-voltage halogen lamps 1250 W
Inductive load 600 VA
Electronic ballast 3 pieces
Height of casing 27 mm, with fastening clips, IP 20, connection via plug-in terminals,
230 V, 50 Hz, neutral conductor required. Up to a total of 30 transmitters can be trained.
Easyclick Plus flush-mounted receiver, 2 channels
The Easyclick flush-mounted receiver, 2 channels (independently programmable) switches 452 FU-EP o.T. 363213
lights and other electrically powered units according to various selectable functions and
parameters per channel. Standard function: 2-pushbutton function
Selectable functions: 1-pushbutton function, sequential pushbutton selection, staircase
lighting function with settable switching off delay and advance off warning, automatic OFF
after a settable delay, ventilator control with delayed ON and automatic OFF, 4 light
scenarios, all can be saved and activated at the touch of a button (one light scenario per
pushbutton), ventilator control with window monitoring. One function can be specified
individually per transmitter once it has been trained.
Connection data per channel: Filament lamp (ohmic load) 500 W
High-voltage halogen lamps 100 W
Inductive load 100 VA
Electronic ballast 1 piece
Height of casing 27 mm, with fastening clips, IP 20, connection via plug-in terminals,
230 V, 50 Hz, neutral conductor required. Up to a total of 30 transmitters can be trained.
Article designation Colour Article No. Code No.
Easyclick flush-mounted JR receiver Plus, 2 channels
The Easyclick flush-mounted receiver controls shutters and blinds according to various 452 FU-EP JR o.T. 363313
selectable functions and parameters.
Standard function: UP/STOP/DOWN with adjustment of louver tilt
Selectable functions: UP/STOP/DOWN without adjustment of louver tilt, sequential push-
button selection for louver tilt, ON/OFF of sun protection function, security function for
blocking the shutters, the sun protection function is already integrated for future solutions,
4 positions UP/DOWN for light scenarios.
One function can be specified individually per transmitter once it has been trained.
Connection data: rated switching capacity (maximum) 600 VA
Height of casing 27 mm, with fastening clips, IP 20, connection via plug-in terminals,
230 V, 50 Hz, neutral conductor required. Up to a total of 30 transmitters can be trained.
Easyclick flush-mounted JR receiver Plus with support plate, 2 channels
The Easyclick flush-mounted receiver controls shutters and blinds according to various 452 FU-EP JR UP o.A. 348113
selectable functions and parameters.
• With support plate for screw attachment in switch sockets with 60 mm distance
to the device screws
• Socket board for the attachment of the button fixture xx.425.xx JR for the control (local)
Standard function: Button fixture: Left button UP, right button DOWN with shutter adjustment,
Easyclick transmitter: 2-pushbutton function UP/DOWN with shutter
adjustment.
Settable functions with button fixture: UP/DOWN with shutter adjustment, touch operation
for shutter adjustment.
Settable functions with Easyclick transmitter: UP/DOWN without louver adjustment,
touch operation for louver adjustment, ON/OFF of sun protection function, sun protection
function for further solution already integrated, safety function to block the blind, 4 position
situations UP/DOWN for light scenarios.
One function can be specified individually per transmitter once it has been trained.
Connection data: 600 VA,
IP 20, 230 V, 50 Hz, neutral conductor required.
Up to a total of 30 transmitters can be trained.
Easyclick baldachin receiver Plus, 1 channel
The Easyclick baldachin receiver switches lights and other electrically powered units 451 FU-BEP 363813
according to various selectable functions and parameters.
Standard function: 2-pushbutton function
Selectable functions: 1-pushbutton function, sequential pushbutton selection, staircase
lighting function with settable switching off delay and advance off warning, automatic
OFF after a settable delay, ventilator control with delayed ON and automatic OFF,
4 light scenarios, all can be saved and activated at the touch of a button (one light
scenario per pushbutton), ventilator control with window monitoring.
One function can be specified individually per transmitter once it has been trained.
Connection data: Filament lamp (ohmic load) 2500 W
High-voltage halogen lamps 1250 W
Inductive load 600 VA
Electronic ballast 3 pieces
Height of casing 27 mm, with screw hook hole, IP 20 , with connection wiring,
230 V, 50 Hz, neutral conductor required. Up to a total of 30 transmitters can be trained.
Easyclick flush-mounted dimmer receiver Plus with support plate, 1 channel
The Easyclick baldachin receiver switches and dims lights according to various selectable 451 FU-EP DAB UP o.A. 348213
functions and parameters.
This dimmer is controlled by trailing-edge phase cut; it is used with low-voltage halogen
lamps with electronic transformer, filament lamps, high-voltage halogen lamps, and other
ohmic loads.
• With support plate for screw attachment in switch sockets with 60 mm distance
to the device screws
• Socket board for the attachment of the button fixture xx.420.xx for switching and
dimming (local)
Standard function: button fixture xx.420.xx: 1-pushbutton function with memory,
Easyclick transmitter: 2-pushbutton function with memory.
Selectable function with button fixture xx.420.xx: 1-pushbutton function without memory
and with settable brightness after switching on, staircase lighting with settable switching
off time and advance OFF warning.
Settable function with Easyclick transmitter: 2-pushbutton function without memory and
with settable brightness after switching on, ON/OFF defined with 2-pushbutton functions,
UP/DOWN/DIM defined with 2-pushbutton functions, 1-pushbutton function with memory,
staircase lighting with settable switching off time and advance OFF warning, save and
activate 4 light scenarios at the touch of a button (i.e. for a 4-channel transmitter one light
scenario per pushbutton).
One function can be specified individually per transmitter once it has been trained.
Connection data: 60 (minimum ) to 210 (maximum) watts (trailing-edge phase),
IP 20, 230 V, 50 Hz, neutral conductor required.
Up to a total of 30 transmitters can be trained.
Article designation Colour Article No. Code No.
Easyclick radio system
Easyclick baldachin dimmer receiver Plus, 1 channel
The Easyclick baldachin receiver switches and dims lights according to various selectable 451 FU-BEP DAB 363913
functions and parameters.
This dimmer is controlled by trailing-edge phase cut; it is used with low-voltage halogen
lamps with electronic transformer, filament lamps, high-voltage halogen lamps, and other
ohmic loads.
Standard function: ON/OFF/dimming, 2-pushbutton function with memory.
Selectable functions: ON/OFF/dimming, 2-pushbutton function without memory,
ON/OFF defined by 2-pushbutton function, dim up/dim down defined by 2-pushbutton
function, ON/OFF/dimming, 1-pushbutton function with memory, staircase lighting
function with settable switching off delay and advance off warning, 4 light scenarios,
all can be saved and activated at the touch of a button (one lighting scenario per push-
button). One function can be specified individually per transmitter once it has been trained.
Connection data: 60 (minimum ) to 250 (maximum) watts
Height of casing 27 mm, with screw hook hole, IP 20, with connection wiring,
230 V, 50 Hz, neutral conductor required. Up to a total of 30 transmitters can be trained.
Button fixture, 1 gang, for Easyclick in-wall receiver with support plate
451 FU-EP UP o.A. and 451 FU-EP DAB UP o.A.
AURA pure white 20.420.02 119113
anthracite 20.420.21 132413
aluminum 20.420.70 158713
Note: The button fixtures can also be delivered in the STANDARD, DIALOG and
NOVA design.
Button fixture, 2 gang, for Easyclick in-wall receiver with support plate,
with lable UP/DOWN 452 FU-EP JR UP o.A.
AURA pure white 20.425.02 JR 132013
anthracite 20.425.21 JR 132113
aluminum 20.425.70 JR 132813
Note: The button fixtures can also be delivered in the STANDARD, DIALOG and
NOVA design.
Easyclick 2-level repeater in plug casing (SCHUKO)
The Easyclick repeater increases the range and therefore the working area between pure white 453 FU-RP ST 349013
Easyclick transmitters and receivers.
In 1-level operation the radio signal of the transmitter is received, verified and sent to the
respective receiver with the maximum transmission power.
In the 2-level operation a radio signal can be sent over an even greater distance using
maximum two repeaters to the respective receivers. A configuration is not necessary for
the repeater (e.g. programming the transmitter).
The implementation is done with the simple plugging in to a SCHUKO plug.
The 1-level operation of the repeater is the standard factory settings and the repeater can
simply be changed to the 2-level operation depending on the project.
IP 20, 230 V, 50 Hz, neutral conductor required.
Easyclick 2-level flush-mounted repeater
The Easyclick repeater increases the range and therefore the working area between 453 FU-RPP o.T. 379513
Easyclick transmitters and receivers.
In 1-level operation the radio signal of the transmitter is received, verified and sent to the
respective receiver with the maximum transmission power.
In the 2-level operation a radio signal can be sent over an even greater distance using
maximum two repeaters to the respective receivers. A configuration is not necessary for
the repeater (e.g. programming the transmitter).
The implementation is done with the simple plugging in to a 230 V,
e.g. a 1960s switch plug.
The 1-level operation of the repeater is the standard factory settings and the repeater can
simply be changed to the 2-level operation depending on the project.
IP 20, 230 V, 50 Hz, neutral conductor required.
Easyclick window contact
This door/window contact monitors the status of doors and windows, it does not need a 450 FU FK 367113
battery, it is operated by Easyclick radio signals via the Easyclick Plus receiver.
The Easyclick window contact is wireless and completely maintenance-free, it incorporates
an internal solar-powered energy store. It continues to operate through dark spells lasting
several days. Signal transmission is immediate, as soon as a window opens or closes, it is
triggered by a window magnet. The window contact can be fitted to all the usual frame
profiles. Thanks to its wireless radio transmission the window contact is ideal for installing
in existing buildings in order to improve security. It is compatible with the Easyclick Plus
receiver and the PHC system. Colour similar to RAL 9003, protection IP 40,
dimensions of the window contact: 110 x 19 x 15 mm (L x W x H),
dimensions of the magnet: 23 x 14 x 6 mm (L x W xH).
Article designation Colour Article No. Code No.
Cover for flush-mounted receiver
Cover for Easyclick flush-mounted receiver and Easyclick flush-mounted repeater,
other colors available on request. AURA pure white 20.477.02 372613
Easyclick adapter receiver (SCHUKO) Plus, 1 channel (SCHUKO)
Easyclick plug adapter receivers for switching of lights and other electronic consumers pure white 4511 FU-EP ST 349113
with regard to different settable functions and parameters.
Standard function: 2-pushbutton function.
Selectable functions: 1-pushbutton function, sequential pushbutton function,
staircase lighting function with settable switching off delay and advance OFF warning,
automatic OFF after a settable delay, ventilator control function with delayed ON and
automatic switching off, save and activate 4 light scenarios at the touch of a button
(i.e. for a 4-channel transmitter one light scenario per pushbutton),
ventilator control function with window monitoring.
One function can be specified individually per transmitter once it has been trained.
Connection data: Filament lamp (ohmic load) 2500 W
High-voltage halogen lamps 1250W
Electronic ballast 3 pieces
IP 20, 230 V, 50 Hz, neutral conductor required. Up to a total of 32 transmitters
can be trained.
Plug adapter version in preparation: with earthing pin 4571 FU-EP ST 349613
to Swiss standard (SEV) (Schweizerischer Elektrotechnischer Verein) 4571 FU-EP ST CH 349713
in accordance with British norm 4571 FU-EP ST GB 349913
Easyclick adapter dimmer receiver (SCHUKO) Plus, 1 channel (SCHUKO)
Easyclick plug adapter receivers switches and dims lights with regard to different settable pure white 4511 FU-EP DAB ST 349213
functions and parameters.
This dimmer is controlled by trailing-edge phase cut; it is used with low-voltage halogen
lamps with electronic transformer, filament lamps, high-voltage halogen lamps, and other
ohmic loads.
Standard function: ON/OFF/dimming, 2-pushbutton function with memory.
Selectable functions: ON/OFF/dimming, 2-pushbutton function without memory and
with settable brightness after switching on, ON/OFF defined with 2-pushbutton functions,
UP/DOWN/DIM defined with 2-pushbutton functions, 1-pushbutton function with memory,
staircase lighting with settable switching off time and advance OFF warning, save and
activate 4 light scenarios at the touch of a button (i.e. for a 4-channel transmitter one light
scenario per pushbutton).
One function can be specified individually per transmitter once it has been trained.
The plug adapter has a protection function for unsuited kinds of load and switches OFF
automatically.
Connection data: 60 (minimum ) to 420 (maximum) watts (trailing-edge phase cut),
IP 20, 230 V, 50 Hz, neutral conductor required. Up to a total of 32 transmitters
can be trained.
Plug adapter version in preparation: with earthing pin 4571 FU-EP DAB ST 345413
to Swiss standard (SEV) (Schweizerischer Elektrotechnischer Verein) 4571 FU-EP DAB ST CH 345513
in accordance with British norm 4571 FU-EP DAB ST GB 345613
Easyclick flush-mounted ceiling receiver
4-channel switching module, with two pushbuttons, each with ON/OFF function. 454 FU-E DE 380113
30 Easyclick transmitters can be trained to work with one receiver.
Connection options: 3 push-to-make switches and 1 changeover contact (zero-potential
and independently programmable), dimensions: 230 x 55 x 36 mm (LxWxH)
Supply voltage 230 V, 50 Hz, neutral conductor required, screw terminals,
the contacts must not be operated with mixed voltages (i.e. safety extra-low voltage
and 230 V).
Connection data for electrically powered units
per channel: push-to-make (PTM) push-to-break (PTB)
Filament lamp (ohmic load) 2500 W 1000 W
High-voltage halogen lamps 1250 W 500 W
Inductive load 600 VA 250 W
Electronic ballast 3 pieces 1 piece
Article designation Colour Article No. Code No.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

PEHA AURA User manual

Category
Wall transmitters
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI