ECS G31T-M9 User manual

Preface

Copyright

This publication, including all photographs, illustrations and software, is protected

any of the material contained herein, may be reproduced without written consent of

the author.

Version 1.0a

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any

particular purpose. The manufacturer reserves the right to revise this publication and

to make changes from time to time in the content hereof without obligation of the

manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective

owners and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful inter-

ference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment onto an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits govern-

ing this device. Changes or modifications not expressly approved by the system’s

manufacturer could void the user’s authority to operate the equipment.

ii

Preface

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the

following conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including interfer-

ence that may cause undesired operation

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur

le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Describes features of the

motherboard.

Go to

H

page 1

Describes installation of

motherboard components.

Go to

H

page 7

Provides information on us-

ing the BIOS Setup Utility.

Go to

H

page 27

Describes the motherboard

software

Go to

H

page 43

Chapter 1

Introducing the Motherboard

Chapter 2

Installing the Motherboard

Chapter 3

Using BIOS

Chapter 4

Using the Motherboard Software

iii

TT

T

ABLE OF CONTENTSABLE OF CONTENTS

ABLE OF CONTENTS

Preface i

Chapter 1 1

Introducing the Motherboard 1

Introduction......................................................................................1

Feature...............................................................................................2

Motherboard Components.............................................................4

Chapter 3 27

Using BIOS 27

About the Setup Utility.................................................................27

The Standard Configuration...................................................27

Entering the Setup Utility........................................................27

Resetting the Default CMOS Values.......................................28

Using BIOS.....................................................................................29

Standard CMOS Setup...........................................................30

Advanced Setup......................................................................31

Advanced Chipset Setup.........................................................33

Chapter 2

7 7

7

Installing the Motherboard 7

Safety Precautions...........................................................................7

Choosing a Computer Case............................................................7

Installing the Motherboard in a Case...........................................7

Checking Jumper Settings..............................................................8

Setting Jumpers........................................................................8

Checking Jumper Settings........................................................9

Jumper Settings........................................................................9

Installing Hardware.......................................................................10

Installing the Processor.........................................................10

Installing Memory Modules...................................................12

Expansion Slots......................................................................15

Connecting Optional Devices................................................17

Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive..20

Connecting I/O Devices..............................................................22

Connecting Case Components....................................................23

Front Panel Header................................................................25

iv

Integrated Peripherals.............................................................34

Power Management Setup.......................................................35

PCI/PnP Setup.........................................................................37

PC Health Status.....................................................................37

Frequency/Voltage Control......................................................39

Load Default Settings..............................................................40

Supervisor Password..............................................................40

User Password........................................................................41

Save & Exit Setup....................................................................41

Exit Without Saving..................................................................41

Updating the BIOS...................................................................42

Chapter 4

43 43

43

Using the Motherboard Software 43

About the Software CD-ROM......................................................43

Auto-installing under Windows Vista.........................................43

Running Setup.........................................................................44

Manual Installation........................................................................48

Utility Software Reference............................................................48

1

Introducing the Motherboard

Chapter 1

Introducing the Motherboard

Introduction

Thank you for choosing the G31T-M9 motherboard. This motherboard is a high

performance, enhanced function motherboard designed to support the LGA775 socket

Intel

®

Core

TM

2 Duo/Pentium

®

Dual-Core/Celeron

®

4xx Series processors for high-

end business or personal desktop markets.

The motherboard incorporates the G31 Northbridge (NB) and ICH7 Southbridge

(SB) chipsets. The Northbridge supports a Front Side Bus (FSB) frequency of 1333/

1066/800 MHz using a scalable FSB Vcc_CPU. The memory controller supports

DDR2 memory DIMM frequencies of 800/667. It supports two DDR2 sockets with

up to maximum memory of 4 GB. DDR2 Maximum memory bandwidth of 12.8 GB/

s in dual-channel symmetric mode assuming DDR2 800 MHz. High resolution graph-

ics via one PCI Express slot, intended for Graphics Interface, is fully compliant to the

PCI Express Base Specification revision 1.1.

The ICH7 Southbridge supports one PCI slot which is PCI v2.3 compliant. In addi-

tion, one PCI Express x1 slot is supported, fully compliant to the PCI Express Base

Specification revision 1.1. It implements an EHCI compliant interface that provides

480 Mb/s bandwidth for six USB 2.0 ports (four USB ports and one USB 2.0 header

supports additional two USB ports). One onboard IDE connector supports two IDE

devices in Ultra ATA 100/66/33 mode. The Southbridge integrates a Serial ATA host

controller, supporting two SATA ports with maximum transfer rate up to 3.0 Gb/s

each.

The motherboard is equipped with advanced full set of I/O ports in the rear panel,

including PS/2 mouse and keyboard connectors, VGA port, four USB ports, one LAN

port, and audio jacks for microphone, line-in and line-out.

2

Introducing the Motherboard

Feature

The motherboard uses an LGA775 type of Intel

®

Core

TM

2 Duo/Pentium

®

Dual-

Core/Celeron

®

4xx Series that carries the following features:

Processor

The G31 Northbridge (NB) and ICH7 Southbridge (SB) chipsets are based on an

innovative and scalable architecture with proven reliability and performance.

Chipset

ICH7 (SB)

G31 (NB)

• Supports 36-bit host bus addressing, allowing the CPU

to access the entire 64 GB of the memory address

space

• 2 GB/s point-to-point Direct Media Interface (DMI) to

ICH7 (1 GB/s each direction)

• Supports 512 Mb and 1 Gb DDR2 DRAM technologies

for x8 and x16 devices

• One, 16-lane PCI Express port intended for Graphics

Attach, compatible to the PCI Express* Base Specifi-

cation revision 1.1

• Enhanced DMA Controller, interrupt controller, and timer

functions

• Compliant with PCI Express* Base Specification, Revi-

sion 1.1

• Compliant with PCI 2.3 specification

• Integrated SATA 3.0 Gb/s Host Controller

• Integrated USB 2.0 Host Controller

• Integrated IDE controller supports Ultra ATA 100/66/33

• Accommodates Intel

®

Core

TM

2 Duo/Pentium

®

Dual-Core/Celeron

®

4xx

Series

processors

• Supports a system bus (FSB) of 1333/1066/800 MHz

Memory

• Supports DDR2 800/667 DDR2 SDRAM with Dual-channel architecture

Accommodates two unbuffered DIMMs

• 2 x 240-pin DDR2 DIMM sockets support up to 4 GB

3

Introducing the Motherboard

This motherboard may support either of the following Audio chipsets:

The motherboard comes with the following expansion options:

• One PCI Express slot for Graphic Interface

• One PCI Express x1 Slot

• One 32-bit PCI v2.3 compliant slot

• One IDE connector that supports two IDE devices

• Two 7-pin SATA connectors

Expansion Options

• 5.1 Channel High Definition Audio Codec

• Exceeds Microsoft Windows Logo Program (WLP) Requirements

• ADCs support 44.1K/48K/96K/192KHz sample rate

• Power Support: Digital: 3.3V; Analog: 5.0V

Audio

Onboard LAN (optional)

The onboard LAN controller provides either of the following features:

• Supports 10/100 Mbps Ethernet Transceiver

• Fully compliant with IEEE802.3, IEEE802.3u, IEEE802.3ab

• Wake-On-LAN (WOL) by Magic Packet/Frame/Link Change

• Integrated PHY for 10/100/1000 Mbps

• IEEE 802.3x compliant flow control support

• Three power supplies: 2.5V, 1.8V and 1.2V

• PCI Express base 1.1 compliant

• Two PS/2 ports for mouse and keyboard

• One VGA port

• Four USB ports

• One LAN port

• Audio jacks for microphone, line-in and line-out

The motherboard has a full set of I/O ports and connectors:

Integrated I/O

1.Some hardware specifications and software items are subject to change

without prior notice.

2.Due to chipset limitation, we recommend that motherboard be oper-

ated in the ambiance between 0 and 50°C.

The firmware can also be used to set parameters for different processor clock

speeds.

• Power management

• Wake-up alarms

• CPU parameters

• CPU and memory timing

This motherboard uses AMI BIOS that enables users to configure many system

features including the following:

BIOS Firmware

4

Introducing the Motherboard

Motherboard Components

5

Introducing the Motherboard

Table of Motherboard Components

LABEL COMPONENTS

LGA775 socket for Intel

®

Core

™

2 Duo/

Pentium

®

Dual-Core/Celeron

®

4xx Series processors

2. CPU_FAN

CPU cooling fan connector

3. DDR2_1~2

240-pin DDR2 SDRAM slots

4. ATX_POWER

Standard 24-pin ATX power connector

5. IDE

Primary IDE channel

6. SPK

Speaker header

7. CLR_CMOS

Clear CMOS

j

umper

8. F_PANEL

Front Panel switch/LED header

9. F_USB

Front Panel USB header

10. SATA1~2

Serial ATA connectors

11. LPT

Onboard parallel port header

12. F_AUDIO

Front panel audio header

13. PCI1

32-bit add-on card slot

14. CO

M

Onboard serial port header

15. PCIE

PCI Express x1 slot

16. PCIEX16

PCI Express x16 graphics card slot

Rear Panel USB PS/2 Power Select Jumper (for PS/2

S3 wake-up only)

18. ATX12

V

4-pin +12V power connector

1. CPU Socket

17. KBMPWR

This concludes Chapter 1. The next chapter explains how to install the motherboard.

6

Introducing the Motherboard

Memo

7

Installing the Motherboard

Chapter 2

Installing the Motherboard

Safety Precautions

• Follow these safety precautions when installing the motherboard

• Wear a grounding strap attached to a grounded device to avoid dam-

age from static electricity

• Discharge static electricity by touching the metal case of a safely

grounded object before working on the motherboard

• Leave components in the static-proof bags they came in

• Hold all circuit boards by the edges. Do not bend circuit boards

Choosing a Computer Case

There are many types of computer cases on the market. The motherboard complies

with the specifications for the Micro ATX system case. First, some features on the

motherboard are implemented by cabling connectors on the motherboard to indica-

tors and switches on the system case. Make sure that your case supports all the

features required. Secondly, this motherboard supports two enhanced IDE drives.

Make sure that your case has sufficient power and space for all drives that you intend

to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O

template in the case matches the I/O ports installed on the rear edge of the

motherboard.

This motherboard carries a Micro ATX form factor of 225 x 170 mm. Choose a case

that accommodates this form factor.

Installing the Motherboard in a Case

Refer to the following illustration and instructions for installing the motherboard in

a case.

Most system cases have mounting brackets installed in the case, which correspond

the holes in the motherboard. Place the motherboard over the mounting brackets

and secure the motherboard onto the mounting brackets with screws.

Ensure that your case has an I/O template that supports the I/O ports and expansion

slots on your motherboard.

8

Installing the Motherboard

Checking Jumper Settings

This section explains how to set jumpers for correct configuration of the motherboard.

Setting Jumpers

Use the motherboard jumpers to set system configuration options. Jumpers with

more than one pin are numbered. When setting the jumpers, ensure that the jumper

caps are placed on the correct pins.

The illustrations show a 2-pin jumper.

When the jumper cap is placed on both

pins, the jumper is SHORT. If you re-

move the jumper cap, or place the jumper

cap on just one pin, the jumper is OPEN.

This illustration shows a 3-pin jumper.

Pins 1 and 2 are SHORT.

SHORT OPEN

Do not over-tighten the screws as this can stress the motherboard.

9

Installing the Motherboard

Checking Jumper Settings

The following illustration shows the location of the motherboard jumpers. Pin 1 is

labeled.

Jumper Settings

KBMPWR

Jumper

Type

Description Setting (default)

CLR_CMOS

3-pin

Clear CMOS

1-2: NORMAL

2-3: CLEAR

Before clearing the

CMOS, make sure to

turn off the system.

CLR_CMOS

KBMPWR

3-pin

1-2: VCC

2-3: 5VSB

1. To avoid the system instability after clearing CMOS, we recommend

users to enter the main BIOS setting page to “Load Default Settings”

and then “Save Changes and Exit”.

2. Make sure the power supply provides enough 5VSB voltage before

selecting the 5VSB function.

3. It is required that users place the KBMPWR cap onto 2-3 pin rather

than 1-2 pin as default if you want to wake up the computer by USB/PS2

KB/Mouse.

1

Rear USB PS/2

Power Select

Jumper (for

PS/2 S3 wake-

up only)

10

Installing the Motherboard

Installing Hardware

Installing the Processor

Caution: When installing a CPU heatsink and cooling fan make sure

that you DO NOT scratch the motherboard or any of the surface-

mount resistors with the clip of the cooling fan. If the clip of the cooling

fan scrapes across the motherboard, you may cause serious damage

to the motherboard or its components.

On most motherboards, there are small surface-mount resistors near

the processor socket, which may be damaged if the cooling fan is

carelessly installed.

Avoid using cooling fans with sharp edges on the fan casing and the

clips. Also, install the cooling fan in a well-lit work area so that you

can clearly see the motherboard and processor socket.

Before installing the Processor

This motherboard automatically determines the CPU clock frequency and system bus

frequency for the processor. You may be able to change the settings in the system

Setup Utility. We strongly recommend that you do not over-clock processors or

other components to run faster than their rated speed.

This motherboard has an LGA775 socket. When choosing a processor, consider the

performance requirements of the system. Performance is based on the processor

design, the clock speed and system bus frequency of the processor, and the quantity

of internal cache memory and external cache memory.

Warning:

2. Always remove the AC power by unplugging the power cord from

the power outlet before installing or removing the motherboard or

other hardware components.

1. Over-clocking components can adversely affect the reliability of the

system and introduce errors into your system. Over-clocking can per-

manently damage the motherboard by generating excess heat in com-

ponents that are run beyond the rated limits.

11

Installing the Motherboard

A. Read and follow the instructions shown

on the sticker on the CPU cap.

B. Unload the cap

· Use thumb & forefinger to hold the

lifting tab of the cap.

· Lift the cap up and remove the cap

completely from the socket.

C. Open the load plate

· Use thumb & forefinger to hold the

hook of the lever, pushing down and

pulling aside unlock it.

· Lift up the lever.

· Use thumb to open the load plate. Be

careful not to touch the contacts.

D. Install the CPU on the socket

· Orientate CPU package to the socket.

Make sure you match triangle marker

to pin 1 location.

E. Close the load plate

· Slightly push down the load plate onto

the tongue side, and hook the lever.

· CPU is locked completely.

F. Apply thermal grease on top of the CPU.

G. Fasten the cooling fan supporting base

onto the CPU socket on the motherboard.

H. Make sure the CPU fan is plugged to the

CPU fan connector. Please refer to the

CPU cooling fan user’s manual for more

detail installation procedure.

CPU Installation Procedure

The following illustration shows CPU installation components.

1. To achieve better airflow rates and heat dissipation, we suggest that

you use a high quality fan with 3800 rpm at least. CPU fan and

heatsink installation procedures may vary with the type of CPU fan/

heatsink supplied. The form and size of fan/heatsink may also vary.

2. DO NOT remove the CPU cap from the socket before installing a

CPU.

3. Return Material Authorization (RMA) requests will be accepted

only if the motherboard comes with the cap on the LGA775 socket.

12

Installing the Motherboard

Installing Memory Modules

This motherboard accommodates two memory modules. It can support two 240-pin

DDR2 800/667. The total memory capacity is 4 GB.

You must install at least one module in any of the two slots. The total memory

capacity is up to 4 GB.

Do not remove any memory module from its antistatic packaging

until you are ready to install it on the motherboard. Handle the

modules only by their edges. Do not touch the components or metal

parts. Always wear a grounding strap when you handle the modules.

Installation Procedure

Refer to the following to install the memory modules.

1 This motherboard supports unbuffered DDR2 SDRAM .

2 Push the latches on each side of the DIMM slot down.

3 Align the memory module with the slot. The DIMM slots are keyed with

notches and the DIMMs are keyed with cutouts so that they can only be

installed correctly.

4 Check that the cutouts on the DIMM module edge connector match the

notches in the DIMM slot.

5 Install the DIMM module into the slot and press it firmly down until it

seats correctly. The slot latches are levered upwards and latch on to

the edges of the DIMM.

6 Install any remaining DIMM modules.

DDR2 SDRAM memory module table

DDR2 800 400 MHz

Memory module Memory Bus

DDR2 667 333 MHz

13

Installing the Motherboard

Table A: DDR2 (memory module) QVL (Qualified Vendor List)

The following DDR2 800/667 memory modules have been tested and qualified for

use with this motherboard.

Type Size Vendor Module Name

Apacer 78.91G92.9K5

Micron MT4HTF6464AY-667E1

PSC AL6E8E63J-6E1

Ramxel RML1520M38D6F-667

512 MB

Samsung PC2-5300U-555-12-D3

AU01GE667C5KBGC

78.01G9O.9K5

Apacer

1GB UNB PC2-5300 CL5

Corsair VS1GB667D2

Hexon HYNT7AUDR-30M48

Kingston KVR667D2N5

Micron MT8HTF12864AY-667E1

AL7E8E63B-6E1T

AL7E8F63J-6E1

PSC

AL7E8F73C-6E1

1 GB

Samsung GOLD BAR M378T2863DZS 0742

Aeneon AET860UD00-30DB08X

Apacer 78.A1G9O.9K4

Hynix HYMP125U64AP8-Y5 AB-A 0623

Hexon HYNT8AUDR-30M88

Kingston KVR667D2N5/2G

LeadMax PC2-5300U

PSC AL8E8F73C-6E1

2 GB

Qimonda HYS64T256020EU-3S-C2

DDR2 667

4 GB

Aeneon AET960UD00-30D

14

Installing the Motherboard

Type Size Vendor Module Name

Kingston

KVR800D2N5/512 1.8V 9905315-

019.A02LF

Micron MT8HTF6464AY-80ED4

512 MB

Qimonda HYS72T64000HU-2.5-B

A-DATA M2GVD6G3I41P0U1E5E

AET760UD00-30DB97X

Aeneon

AET760UD00-25DC08X

AU01GE800C5KBGC

Apacer

78.01GAO.9K5

APOGEE AU1G082-800P000

Geil GEIL MILLENARY

Hexon ELPT7AUDR-25M48

Infinity 04701G16CZ5U2G

Kingston

KVR800D2N5/1G 1.8V 9905316-

054.A01LF

Nanya NT1GT64U88D0BY-AD

PSC AL7E8F73C-8E1

Ramaxel RML1320EH38D7F-800

GOLD BAR M378T2953EZ3-CE7 0726

Samsung

M378T2863EHS-CF7 0849

Silicon Power SP001GBLRU800S01

Transcend 507301-1571

1 GB

Unifosa GU341G0ALEPR6B2C6CE

A-DATA RED A-DATAM2OMI6H3J4720L1C5Z

Aeneon AET860UD00-25DC08X

Apacer 78.A1GAO.9K4

CORSAIR CM2X2048-6400C5

Geil

PLATINUM

EDITION/Geil/BOXED/2GB/DS

Hexon ELPT8AUDR-25M88

KVR800D2N6/2G-SP

Kingston

KVR800D2N5/2G

Micron MT16HTF25664AY-800E1

Nanya NT2GT64U8HD0BY-AD

PSC AL8E8F73C-8E1

Qimonda HYS64T256020EU-25F-C2

Samsung M378T5663QZ3-CF7

Silicon Power SP002GBLRU800S01

Samsung M378T5663EH3-CF7 0849

2 GB

Unifosa GU342G0ALEPR692C6CE

Aeneon AET960UD00-25D

DDR2 800

4 GB

Samsung M378T5263AZ3-CF7 0819

Aeneon AXT760UD00-19DC97X//7/1GB

Infinity 04701G16CY5U2A

DDR2 1066 1 GB

OCZ OCZ2RPR10662GK

Users please note that: According to Intel G31 Chipset Specification,

the frequency of memory will downgrade to 800 MHz when using

DDR2 1066.

15

Installing the Motherboard

Installing Add-on Cards

The slots on this motherboard are designed to hold expansion cards and connect

them to the system bus. Expansion slots are a means of adding or enhancing the

motherboard’s features and capabilities. With these efficient facilities, you can in-

crease the motherboard’s capabilities by adding hardware that performs tasks that are

not part of the basic system.

Before installing an add-on card, check the documentation for the

card carefully. If the card is not Plug and Play, you may have to

manually configure the card before installation.

This motherboard is equipped with one standard PCI slot. PCI stands

for Peripheral Component Interconnect and is a bus standard for

expansion cards, which for the most part, is a supplement of the

older ISA bus standard. The PCI slot on this board is PCI v2.3

compliant.

PCI1 Slot

PCIEX16 Slot

The PCI Express x1 slot is fully compliant to the PCI Express*

Base Specification revision 1.1 as well.

The PCI Express slot is used to install an external PCI Express

graphics card that is fully compliant to the PCI Express* Base

Specification revision 1.1.

PCIE Slot

Expansion Slots

16

Installing the Motherboard

Follow these instructions to install an add-on card:

1 Remove a blanking plate from the system case corresponding to the

slot you are going to use.

2 Install the edge connector of the add-on card into the expansion slot.

Ensure that the edge connector is correctly seated in the slot.

3 Secure the metal bracket of the card to the system case with a screw.

2. The onboard PCI interface does not support 64-bit SCSI cards.

1. For some add-on cards, for example graphics adapters and network

adapters, you have to install drivers and software before you can begin

using the add-on card.

Page is loading ...

ECS G31T-M9 User manual

Related papers

Other documents