Kathrein HDP 160 User manual

Kathrein
Brand
Kathrein
Model
HDP 160
Type
User manual
Page is loading ...
Page is loading ...
936.2186/A/0805/1.2e
Instructions for retrofitting
the automatic positioner HDP 160
to digital reception
The retrofitting set consists of:
Control unit HDS 160
4 screws
Adapter cable 2-pin (power supply)
Adapter cable 8-pin (control cable)
Coaxial connection cable with F-connectors
Operating instructions for HDP 170
Additionally required:
Digital satellite receiver UFD 540, order no. 260515
The mounting set UFZ 540, order no. 20410006, is used
for secure installation of the receiver UFD 540 in a caravan
or mobile home.
Important instructions:
For adaptation to digital reception, a planar
antenna BAS 60 must be mounted on the
automatic positioner HDP 160. Good reception
is not possible with the older planar antenna
BAS 50.
However, you have the possibility to retrofit an older HDP
150/BAS 50 system to digital reception. For this, the planar
antenna BAS 60 and the following parts are required:
-1 sheet order no. 039 4841
-1 sleeve order no. 010 3742
-2 plates order no. 926 129
-2 screws M3 order no. 048 870
An adaptation of the planar antenna BAS 60 on the
automatic positioner HDP 150 is only possible and
permissible with the use of these components. Ensure, that
there is adequate space of Ø 96 cm around the rotating axle
of the positioner for the BAS 60! Danger of collision!
You can order the parts from:
ESC Elektronik Service Chiemgau GmbH
Bahnhofstraße 108, 83224 Grassau, Germany
!
Gefahr
Attention
!
Gefahr
Attention
Reconstruction instructions
– The control unit HDS 160 functions only in conjunction with the Kathrein
digital receiver UFD 540.
– Retrofitted systems with the control unit HDS 160 cannot be operated with
an analogue receiver.
It is not possible to operate the unit with receivers from other manufacturers.
– The older control unit of the HDP 160 or CAP 100 does not function with the
digital receiver UFD 540!
Control unit HDS 160
The control unit has an exchangeable 10 A flat fuse
near the plug-in connections.
After a fuse has blown, the source of failure must be
found and removed.
The defective fuse may only be exchanged with a
fuse with the same nominal value (10 A)!
Fig. 1
Electronic equipment is not household
waste – in accordance with directive
2002/96/EC OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL of
27th January 2003 on used electrical
and electronic equipment, it must be
disposed of properly.
At the end of its service life, take this
unit for disposal at a relevant official
collection point.
The adaptation work may only be carried out by qualified specialist personnel!
It is advisable to dismount the planar antenna BAS 50 with the older control unit. By pressing the
”SUCHEN” button, the antenna support is raised, and the antenna BAS 50 can be dismounted and
replaced with the planar antenna BAS 60.
Lower the antenna support again to the ”parking” position.
Then, exchange the control unit and receiver.
When working on the mains supply, the power supply must be disconnected, in order to avoid
short-circuits.
When working on the rotating unit, the power supply must be disconnected.
Attention! Danger of being pinched by the moving parts.
936.2186/A/0805/2.2e/SKS Subject ot technical changes.
KATHREIN-Werke KG · Anton-Kathrein-Straße 1–3 · Postfach 10 04 44 · D-83004 Rosenheim · Deutschland · Telefon (0 80 31) 18 40 · Telefax (0 80 31) 18 43 06
Internet: http://www.kathrein.de
Mounting steps:
Disconnect the previous control unit and the analogue
receiver.
The connection cables must not be cut!
Screw the control unit HDS 160 onto a wall (e.g. interior
wall of a cabinet) near the location of the previous control
unit on the four fixing holes with the supplied screws.
The thickness of the wall at this position should be at
least 12 mm, otherwise the screws will puncture out the
other side of the wall or damage the surface.
The laid cables or wires behind or in the attaching wall
must not be damaged when rotating the screws.
Observe the available cable lengths (Fig. 3). The control
unit HDS 160 must be installed in such a way, which
allows adequate air circulation behind the unit (installati-
on, for example, on carpeted walls is not allowed!).
Since the control unit has no operating elements, it does
not need to be accessible for operation.
The control unit is only suitable for indoor installation. It
must be protected against moisture.
Avoid laying the cables across sharp edges, and protect
them from rubbing against obstacles.
Connecting and laying the cables
All cable terminals must be locked in place or the coaxial
cables must be securely screwed on.
Use the supplied F-connection cable to connect the
control unit HDS 160 with the receiver UFD 540.
If a longer cable is required for the coaxial connection
between the control unit HDS 160 and the receiver
UFD 540, or from the rotating unit to the receiver, a 75 Ω
coaxial cable with at least 75 dB screening factor must be
used in order to avoid interfering influences or interfering
transmissions.
When all the cable connections are properly established
(refer to Fig. 3), the power supply can be connected again.
The system is now ready for operation.
When switching on the receiver UFD 540, the automatic
positioner HDP 150 or HDP 160 automatically aligns the
planar antenna BAS 60 to the satellite, where the selected
programme on the receiver is found.
For operation of the receiver UFD 540, observe the
operating instructions supplied with the receiver.
Danger of pinching!
When putting the rotating unit into operation,
ensure that nobody particularly children are in
close proximity of the rotating unit and touch
the moving parts.
When you install the rotating unit, disconnect
the power supply. For further information, also
observe the mounting and operating instructions for the
automatic positioner HDP 150 or HDP 160.
!
Gefahr
Achtung!
The cables are to be connected to the new control
unit as follows (Fig. 3 or 1):
–
Coaxial cable from the rotating unit
IF IN
– Coaxial cable to the receiver IF OUT
– Cable from the power supply POWER IN
– Power supply cable to the
rotating unit POWER OUT*
– 8-pin control cable
to rotating unit POSITIONER*
* = with supplied adapter cable
Circuit diagram of existing
analogue system
Fig. 2
Connection of the control
unit HDS 160
with the receiver
UFD 540
Fig. 3
Parking position
Coupler piece
HDZ 161
optional
URS 200
optional
brown
white green
Vehicle`s
electrical
system
Ignition
Control unit
Receiver
e. g. UFD 345/UFD 346 optional
Control unit
brown
white green
Vehicle’s
electrical
system
Ignition
External
IR sensor (optional)
Television set
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Kathrein HDP 160 User manual

Kathrein
Brand
Kathrein
Model
HDP 160
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents