Edimax EW-7514O User manual

Brand: Edimax

Model: EW-7514O

Category: Network antennas

Type: User manual

This manual is also suitable for

EW-7608O

2.4GHz High Gain

Outdoor/Indoor Antenna

14dBi Directional Panel Antenna

8dBi Omni-directional Antenna

User’s Manual

reproduced, transcribed, stored in a retrieval system, translated into any language or computer

language without the prior written consent of the manufacturer.

All brand and product names are trademarks and/or registered trademarks of their respective

companies.

LIMITED WARRANTY

Manufacturer warrants that this antenna kit is free from physical defects in material and

workmanship under the normal use of two (2) years from the date of purchase. If the product is

found to be defective during the warranty period, then, as your sole remedy and as the

manufacturer’s only obligation, manufacturer will repair or replace the kit or component of the kit.

Manufacturer makes no other warranty or representation, expressed, implied or otherwise, regarding

the antenna kit, and specifically disclaims any warranty for merchantability, quality, performance or

fitness for any particular purpose. In no event shall manufacturer’s liability exceed the price paid for

the product from direct, indirect, special, incidental, or consequential damage resulting from the use

of the product, or its documentation.

PRODUCT UPDATE

Manufacturer reserves the rights to revise or update its products and documentation with no

obligation to notify any individual or entity.

Contents

1 Introduction............................................................................... 1

1.1 Technical Specification............................................................................. 1

1.2 Package Content ....................................................................................... 3

2 Installation................................................................................. 4

2.1 Installation Guidelines .............................................................................. 4

2.2 Mounting the Antenna .............................................................................. 4

2.3 Installing the Surge Arrestor..................................................................... 7

2.4 Connecting to the Wireless Access Point ................................................. 8

1 Introduction

Thank you for purchasing this 2.4GHz High Gain Antenna Kit. This product is an

outdoor/indoor antenna kit which extends the transmitting and receiving power of a

IEEE 802.11b compliant Wireless Access Point. With this kit, your wireless network

will have extraordinary transmission distances and wider coverage range.

This kit comes with a 14dBi directional antenna or an 8dBi Omni-directional antenna,

surge arrestor (lightning protector), extension cable, wall/pole mounting kit, and other

accessories. Installers can easily and conveniently build a wireless network in the

interior or external area of building. The kit is completely waterproof and made out of

corrosion resistant material to withstand harsh environments.

1.1 Technical Specification

Antenna

Directional Panel Antenna Omni-Directional Antenna

Application Outdoor/Indoor

(Wall/Pole)

Outdoor/Indoor

(Pole)

Frequency Range 2400-2500MHz 2400-2500MHz

Gain 14dBi 8dBi

Beam Width H30 V30 H360 V15

Approximate Range 3Km 1Km

Impedance 50 Ohms 50 Ohms

Survival Wind Speed 180 Km/hr 180 Km/hr

Lightning Protection DC Ground DC Ground

Cable Length 30cm 50cm

Connector N-female N-female

Temperature -40°C to 80°C -40°C to 80°C

Humidity 100% @ 25°C 100% @ 25°C

Dimensions 240 x 240 x 69.5 mm 630 x 19 mm

Radiation Pattern

14dBi Directional Panel Antenna

8dBi Omni-directional Antenna

Accessories

Extension Cable N-male to RP-SMA-male / 6.5 ft. (2 m) / 1.72dB Transmission

Loss

Interconnecting Cable N-male to N-female / 1.64 ft. (50 cm) / 0.43dB Transmission Loss

Lightning Surge

Arrestor

Lightning surge and static electricity protector / N-female to

N-male

Connector Converter Convert SMB to standard RP-SMA type connector / SMB-male to

RP-SMA-female

Mounting Kit Wall/Pole Mounting

1.2 Package Content

 One Antenna

 One Extension Cable

 One Interconnecting Cable (only for 8dBi Omni-directional antenna)

 One Surge Arrestor

 One Mounting Kit Set

 One Connector Converter

 One User’s Manual

2 Installation

This chapter describes the installation procedure for the antenna kit.

2.1 Installation Guidelines

Please observe the following guidelines when you are installing the antenna kit:

 Avoid placing behind obstacles

Obstructions such as concrete walls, trees, power lines and thick metals limit radio

signal penetration and reduce throughput and range of the wireless device which

the antenna connects to.

 Mount the antenna vertically

This antenna is vertically polarized. Since the antenna has vertical gain, it is very

important to mount the antenna in a vertical (not leaning) position for optimal

performance.

 Use a surge arrestor for antenna installed outdoor

Surge arrestor can protect your wireless device from high voltage surges caused

by discharge and transient at the antenna.

 Do not point the antenna in the direction of people or animals

You should mount the antenna in such manner so as to minimize the potential for

human or animal contact during normal operation.

2.2 Mounting the Antenna

2.2.1 14dBi Directional Panel Antenna

Wall Mount configuration

1. Fix one of the M-shaped fixing to the back of the antenna.

2. Fix the half-round metal stand with a plastic wall tiger and screw horizontally in

the desired mounting position.

3. Connect the other M-shaped metal fixing and the triangle stand with the

corresponding screws and nuts.

4. Fix the triangle stand to the half-round metal stand. The antenna can be

horizontally aligned with this connection.

5. Connect the two M-shaped metal fixings together with the M8 x 110 bolt. The

antenna can be vertically aligned with this connection.

Pole Mount Configuration

Using a Ring Clamp

1. Fix one of the M-shaped metal fixing to the back of the antenna.

2. Perforate the ring clamp into the other M-shaped metal fixing as shown in the

diagram.

3. Fix the clamp on a secure ironed pole in the desired position, the diameter of the

pole is preferably less than 2 inches.

4. Connect the two M-shaped metal fixings together with the M8 x 110 bolt. The

antenna can be vertically aligned with this connection.

Using a Screw Clamp

1. Fix one of the M-shaped metal fixing to the back of the antenna.

2. Push the two M8 x 110 bolts through the other M-shaped metal fixing with two

washers and both screw clamps.

3. Fix the screw clamps on a secure ironed pole in the desired position.

4. Connect the two M-shaped metal fixings together with the M8 x 110 bolt. The

antenna can be vertically aligned with this connection.

2.2.2 8dBi Omni-directional Antenna

Wall Mount configuration

1. Connect the interconnecting cable to the antenna.

2. Put the interconnecting cable into the metal tube and connect the metal tube to the

antenna.

3. Clip the two U-shaped screws to the metal tube with two of the screw clamps.

4. Connect the four screw clamps together using the M8 x 110 bolts.

5. Fix the screw clamps on a secure ironed pole in the desired position.

2.3 Installing the Surge Arrestor

With the surge arrestor attached to the lightning protector of the building, all devices

downstream are protected by the ground from lightning strikes. Please follow the

steps below to install the surge arrestor:

1. Connect one end of the surge arrestor Y to the antenna.

2. Connect the other end of the surge arrestor X to the extension cable linked to the

Wireless Access Point.

3. Connect the lightning protector of the building to the surge arrestor Z.

2.4 Connecting to the Wireless

Access Point

The Wireless Access Point is connected to the antenna through an extension cable. A

connector converter attached to the kit is used to convert the SMB connector to the

RP-SMA connector. It is applied to Wireless Access Point with SMB connector.

Please connect the Wireless Access Point together according to the diagram.

Edimax EW-7514O User manual

Brand: Edimax

Model: EW-7514O

Category: Network antennas

Type: User manual

This manual is also suitable for

EW-7608O

Download PDF

report

Edimax EW-7514O User manual

This manual is also suitable for

Edimax EW-7514O User manual

Other documents