Fibaro FGBHCD-001 Short Manual

CO SENSOR

CARBON MONOXIDE DETECTOR

& TEMPERATURE SENSOR

Quick Manuals. Warranty Terms

4 x BEEP

&

RED LED

BLINKING

MOVE TO

FRESH AIR!

)

For more information about FIBARO CO Sensor, like video guides,

parameters, technical manuals, and declarations visit our website:

manuals.baro.com/hk-co-sensor

The manufacturer, Fibar Group S.A. will not be held responsible for any

loss or damage resulting from not following instructions of the manuals.

Page is loading ...

4

CEILING

FLOOR

NOT

HERE

30cm/1ft

1.5m/5ft

WALL

Place of installation Battery replacement

B

e

p

!

PULL

1xCR123A(3V)

PULL

1xCR123A(3V)

PULL

1xCR123A(3V)

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Page is loading ...

7

Description

FIBARO CO Sensor is a HomeKit-enabled carbon monoxide detector using Bluetooth® low energy

wireless technology. Its high sensitivity allows to detect the presence of the carbon monoxide (CO)

gas at the early stage in order to prevent carbon monoxide poisoning. Alarm is signalled with a

built-in siren, blinking LED indicator and by sending information to your iOS device. Additionally,

the accessory is equipped with a temperature sensor.

General carbon monoxide information

Carbon monoxide (CO) is a colourless, odourless, and tasteless poison gas that can be fatal when

inhaled. It is produced when liquid, solid, or gas fuel is burned.

Symptoms of carbon monoxide poisoning

The early symptoms of carbon monoxide poisoning can be confused with u-like symptoms:

headache, dizziness and nausea. Breathing carbon monoxide causes these symptoms even in

healthy people. It can also cause sleepiness, vision problems (including blurred vision), ringing

in the ears, aching arms and legs, irregular breathing, fatigue and confusion. At very high levels, it

causes loss of consciousness and death.

Some external factors, eg. exposure to high concentration of basic (non-acidic) gases, silicone va-

pors, hydrogen sulde or sulfuric acid gas, organic vapors, contact with water, dust and oil mist, or

dew condensation may aect the reliability of the device operation.

This device may not protect from long-term exposure to low levels of carbon monoxide which can

also lead to neurological symptoms.

ENGLISH

WHAT YOU HEAR

WHAT YOU SEE WHAT IT MEANS WHAT TO DO

4 x BEEP

every 5s

4 x RED BLINK

every 5s

DETECTED PRESENCE

OF CARBON MONOXIDE

WHICH CAN KILL YOU!

1. Open windows

2. MOVE TO FRESH AIR!

3. Contact emergency services

1 x BEEP

1 x YELLOW BLINK

every 30s

Low battery level Replace battery

1 x BEEP

every 30s

—

Sensor error,

DOES NOT DETECT

CARBON MONOXIDE

Reset accessory,

replace if no eect

2 x BEEP 2 x CYAN BLINK

every 30s

End of lifespan Reset accessory,

replace if no eect

1 x BEEP 1 x WHITE BLINK Tamper alarm Check housing

— 1 x GREEN BLINK after

button press

Accessory

powered

—

1 x BEEP 1 x GREEN BLINK

after powering

Paired with

HomeKit

—

1 x BEEP 1 x RED BLINK

after powering

Not paired with

HomeKit

—

— CYAN BLINKING Firmware update Wait for completion

8

Warnings

Failure to observe recommendations included in the manual may cause risk to life and health

or malfunction of the device.

The manufacturer, Fibar Group S.A. will not be held responsible for any loss or damage resulting

from not following instructions of the manuals.

Risk of malfunction as a result of tampering with the device.

The device should be installed below the ceiling level.

The device should not be installed: in a bathroom, next to heat sources, within range of kids,

obstructed from possible carbon monoxide sources, in direct sunlight.

The device is not a substitute for appropriate ventilation and exhaust systems.

Do not paint the device.

The device should be cleaned with a slightly damp cloth or moistened tissue.

Replace the device before date on the front or if sensor error is detected.

This product is not a toy. Keep away from children and animals!

CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries

According to the Instructions.

Place of installation (page 4)

Install the device on the wall, at least 30 cm (1 ft) away from the corner.

Recommended height of installation is dependant on the purpose of the room and height at

which head typically is.

First launch (page 5)

1) Open the casing by turning the cover counter-clockwise (Fig. 1).

2) Take o the cover (Fig. 2).

3) Remove the battery blocker and check if the battery is placed correctly (Fig. 3).

4) Proper powering up will be conrmed with a short beep (Fig. 4).

5)

Download FIBARO for HomeKit app from the App Store.

6) Open the FIBARO

for HomeKit

app and tap icon.

7) Application will guide you through the pairing process.

8) Mount the cover on a wall (Fig. 5).

9) Attach the device to its cover (Fig. 6).

10) Turn the device clockwise to close it (Fig. 7).

Setup Code

You will nd the Setup Code on the back of this guide.

Remember to keep it in a safe place. You may need it in case of re-pairing.

ENGLISH

9

Hereby, Fibar Group S.A. declares that the

device is in compliance with Directive

2014/53/EU. The full text of the EU declara-

tion of conformity is available at the following internet

address: www.manuals.baro.com

Device labelled with this symbol should not be

disposed with other household wastes. It shall

be handed over to the applicable collection

point for the recycling of waste electrical and electronic

equipment.

Reset

Reset procedure allows to restore the accessory back to factory settings.

1) Press and hold the button.

2) Release the button when LED indicator glows white.

3) Click the button when LED indicator glows yellow.

4) After few seconds the device will be reset (conrmed by red LED indicator).

Self-test

Caution! The alarm is very loud! Only the rst alarm sequence is quieter.

1) Press and hold the button.

2) The LED indicator will glow white and you will hear a short beep - keep holding the button.

3) Release the button when you hear the rst alarm sequence.

4) Move away from the device to protect your hearing.

Battery replacement (page 4)

1) Remove the device from the cover by turning it counter-clockwise.

2) Pull the paper strip to take out the battery.

3) Press and hold the button for at least one second.

4) Insert a new CR123A battery observing the polarities shown inside.

5) Attach the device to its cover by turning it clockwise and perform the test.

Legal information

ENGLISH

Technical data

Battery type: 3V, CR123A (included)

Battery life: 3 years on default settings

(tested with Panasonic

Industrial Lithium)

Lifespan under

typical conditions:

8 years

Operating

temperature:

0-50°C (32-122°F)

Operating humidity: 10-95%RH without

condensation

Dimensions (d x h): 65 x 28 mm

Alarm response times

on default settings:

50ppm 60-90min

100ppm 10-40min

300ppm <1.5min

Measuring accuracy: ±10ppm / ±5%

Radio protocol: Bluetooth® low energy

Radio frequency: 2.4 GHz

Transmit power: max. 10 dBm

Conformity with EU

requirements:

RED 2014/53/EU

RoHS 2011/65/EU

EN 50291-1:2010

Fibaro and Fibar Group are registered trademarks of Fibar

Group S.A. The Bluetooth word mark is registered trademark

of Bluetooth SIG, Inc. Apple and HomeKit are registered

trademarks of Apple Inc.

Use of the Works with Apple HomeKit logo means that an

electronic accessory has been designed to connect specif-

ically to iPod touch, iPhone, or iPad, respectively, and has

been certied by the developer to meet Apple performance

standards. Apple is not responsible for the operation of this

device or its compliance with safety and regulatory stand-

ards.

10

Guarantee terms and conditions

1. FIBAR GROUP S.A. with its registered oce in Poznan,

ul. Lotnicza 1, 60-421 Poznań, entered into the Register of

Entrepreneurs of the National Court Register maintained

by the District Court for Poznań-Nowe Miasto and Wilda

in Poznań, VIII Commercial Division of the National Court

Register (KRS) under number: 553265, NIP 7811858097,

REGON: 301595664, share capital PLN 1,182,100 paid in

full, other contact information is available at: www.baro.

com (hereinafter “the Manufacturer”) guarantees that the

device sold (hereinafter: “the Device” is free from material

and manufacturing defects.

2. The Manufacturer shall be responsible for malfunction-

ing of the Device resulting from physical defects inherent

in the Device that cause its operation to be incompatible

with the specications within the period of:

- 24 months from the date of purchase by the consumer,

- 12 months from the date of purchase by a business cus-

tomer (the consumer and business customer are further

collectively referred to as “Customer”).

3. The Manufacturer shall remove any defects revealed

during the guarantee period, free of charge, by repairing

or replacing (at the sole discretion of the Manufacturer)

the defective components of the Device with new or re-

generated components. The manufacturer reserves the

right to replace the entire Device with a new or regen-

erated device. The Manufacturer shall not refund money

paid for the device.

4. Under special circumstances, the Manufacturer may

replace the Device with a dierent device most similar in

technical characteristics.

5. Only the holder of a valid guaranty document shall be

entitled to make claims under guarantee.

6. Before making a complaint, the Manufacturer recom-

mends using the telephone or online support available at

https://www.baro.com/support/.

7. In order to make a complaint, the Customer should

contact the Manufacturer via the email address given at

https://www.baro.com/support/.

8. After the complaint has been properly led, the Cus-

tomer will receive contact details for the Authorized

Guarantee Service (“AGS”). The customer should contact

and deliver the Device to AGS. Upon receipt of the Device,

the manufacturer shall inform the Customer of the return

merchandise authorization number (RMA).

9. Defects shall be removed within 30 days from the date

of delivering the Device to AGS. The guarantee period

shall be extended by the time in which the Device was

kept by AGS.

10. The faulty device shall be provided by the Customer

with complete standard equipment and documents

proving its purchase.

11. The cost of transporting the Device in the territory

of the Republic of Poland shall be covered by the Man-

ufacturer. The costs of the Device transport from other

countries shall be covered by the Customer. For unjusti-

ed complaints, AGS may charge the Customer with costs

related to the case.

12. AGS shall not accept a complaint claim when:

- the Device was misused or the manual was not ob-

served,

- the Device was provided by the Customer incomplete,

without accessories or nameplate,

- it was determined that the fault was caused by other

reasons than a material or manufacturing defect of the

Device

- the guarantee document is not valid or there is no proof

of purchase,

13. The guarantee shall not cover:

- mechanical damages (cracks, fractures, cuts, abrasions,

physical deformations caused by impact, falling or drop-

ping the device or other object, improper use or not ob-

serving the operating manual);

- damages resulting from external causes, e.g.: ood,

storm, re, lightning, natural disasters, earthquakes, war,

civil disturbance, force majeure, unforeseen accidents,

theft, water damage, liquid leakage, battery spill, weather

conditions, sunlight, sand, moisture, high or low temper-

ature, air pollution;

- damages caused by malfunctioning software, attack of

a computer virus, or by failure to update the software as

recommended by the Manufacturer;

- damages resulting from: surges in the power and/or

telecommunication network, improper connection to the

grid in a manner inconsistent with the operating manual,

or from connecting other devices not recommended by

the Manufacturer.

- damages caused by operating or storing the device in

extremely adverse conditions, i.e. high humidity, dust, too

low (freezing) or too high ambient temperature. Detailed

permissible conditions for operating the Device are de-

ned in the operating manual;

- damages caused by using accessories not recommend-

ed by the Manufacturer

- damages caused by faulty electrical installation of the

Customer, including the use of incorrect fuses;

- damages caused by Customer’s failure to provide main-

tenance and servicing activities dened in the operating

manual;

- damages resulting from the use of spurious spare parts

or accessories improper for given model, repairing and

introducing alterations by unauthorized persons;

- defects caused by operating faulty Device or accesso-

ries.

14. The guarantee shall not cover natural wear and tear

of the Device and its components listed in the operating

manual and in technical documentation as such elements

have a dened operational life.

15. The Device Guarantee shall not exclude, limit or sus-

pend the Customer’s warranty rights.

16. The Manufacturer shall not be liable for damages to

property caused by defective device. The Guarantor shall

not be liable for indirect, incidental, special, consequen-

tial or punitive damages, or for any damages, including,

inter alia, loss of prots, savings, data, loss of benets,

claims by third parties and any other damages arising

from or related to the use of the Device.

ENGLISH

Page is loading ...

Made in Poland

www.baro.com

105449310101

Room: ..........................................................

Write down the location of the device.

HomeKit Setup Code is needed to securely add accessory

to your home. You may need it in case of re-pairing.

Remember to keep it in safe place. Nobody but you has a copy.

FIBARO cannot recover the HomeKit setup code for you.

Fibaro FGBHCD-001 Short Manual

Fibaro FGBHCD-001 Short Manual

in other languages

Related papers

Other documents