ROBINHOOD ST7000 Installation & Operating Manual

ROBINHOOD
Brand
ROBINHOOD
Model
ST7000
Category
Flat panel accessories
Type
Installation & Operating Manual

This manual is also suitable for

750754 Issue F
ECN:3165
INSTALLATION INSTRUCTION
LAUNDRY TUB
PRODUCT DIMENSION
1 Pre-Installation Instruction
The fitting kit supplied:
453 (STCL/STCLF/STCLL)
Height Adjustment - STCLL only.
Fit the four leveling feet supplied to the bottom
of the cabinet and adjust to align with washing
machine height. Tilt laundry tub slightly to assist with
access. Check top of laundry tub with spirit level.
Ensure the cabinet does not rock.
NOTES
House Plumbing supplied by the customer.
Washing Machine Drain System supplied with the Laundry Tub.
Model: STCL
STCLN
STCLF
STCLNF
STCLL (With adjustable feet)
888
17-25
560 (STCL/STCLF/STCLL)
461 (STCLN/STCLNF)
STCLL Only
Max 25
883 (STCL/STCLF/STCLL)
561 (STCLN/STCLNF)
892 (STCLN/STCLNF)
Please read the entire instruction before installing the laundry tub.
A. Regulation Compliance - Comply with current drainage and plumbing regualtions as
required by your local authority. Sanitary plumbing shall only be carried out by a registered plumber.
B. Washing Machine Waste - It is advisable to assemble the washing machine waste hose before
installing the laundry tub to the wall for ease of installation.
C. Determine Site - Determine the most suitable position for the laundry tub. It may be
used either to the left or the right of the washing machine. Allow 10mm clearance between the
units. Mark the position on the floor as reference.
2 Connect Washing Machine
The washing machine waste hose can be connected to either side of the laundry tub. Waste
connection holes are located on the top of the laundry tub. Use the fittings supplied to connect
the washing machine waste hose.
A. It may be necessary to re-orient the waste outlet on the laundry tub. Loosen the screw on
the waste outlet, adjust to suit and then TIGHTEN to avoid flooding.
B. Insert the waste stay into the mounting hole. (Diagram A)
C. Push the flexible waste hose firmly into the waste stay.
D. Insert the waste lock into the waste stay.
E. Use the cable tie to secure the waste hose. Refer to diagram B for the position of the tie
F. Insert the grommet to cover the other hole.
G. IMPORTANT: Ensure the flexible waste is correctly fitted to the plastic waste outlet.
Waste Stay
Waste Lock
Grommet
Cable Tie
MANUFACTURED IN NEW ZEALAND BY:
ROBINHOOD LTD
P.O. BOX 51 201, PAKURANGA,AUCKLAND, N.Z.
TEL: +64 9 272 5129 • FAX: +64 9 272 5148
ISO9001 Certified
The safety latch comes as a standard fitting in the interests of child protection
against dangerous chemicals and cleaning fluids. However, should you not
require the latch it can easily be snipped off with side cutters or a similar tool.
5 Safety Latch
4. Tap in
hinge pins
with washers
in position
one at top,
two at
bottom
2. Lever lower
hinge pin out
with door
(keep 3 washers)
1. Knock
out top
hinge pin
3. Turn door around
4 Change Door
A. Position laundry tub and cut the house waste
pipe which should already be installed to the exact
height. The final height will depend on the waste
trap dimensions. Connect the waste trap to the
laundry tub. In New Zealand a waste adaptor
(pictured and supplied) must be glued in place
B. Fasten the cabinet to the wall through the holes
in the back flange of the cabinet sides. Alternative
fastening can be achieved through the bottom flanges.
Waste Adaptor
Apply
Plumbing
PVC glue
* Note: Top outlet is blocked
Rear view
*
Flexible
waste hose
Mounting
holes
3 Securing Laundry Tub
DIAGRAM B.
Cable Tie
DIAGRAM A.
  • Page 1 1

ROBINHOOD ST7000 Installation & Operating Manual

ROBINHOOD
Brand
ROBINHOOD
Model
ST7000
Category
Flat panel accessories
Type
Installation & Operating Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents