Kettler COACH LS 07985-670 Assembly Instructions Manual

Brand: Kettler

Model: COACH LS 07985-670

Type: Assembly Instructions Manual

This manual is also suitable for

COACH LS 07985-679

Page is loading ...

Handling the equipment

■ Before using the equipment for exercise, check carefully to en-

sure that it has been correctly assembled.

■ It is not recommended to use or store the apparatus in a damp

room as this may cause it to rust. Please ensure that no part of

the machine comes in contact with liquids (drinks, perspiration

etc.). This may cause corrosion.

■ The machine is designed for use by adults and children should

not be allowed to play with it. Children at play behave unpre-

dictably and dangerous situations may occur for which the ma-

nufacturer cannot be held liable. If, in spite of this, children are

allowed to use the equipment, ensure that they are instructed in

its proper use and supervised accordingly.

■ Use for your regular cleaning, maintenance and care our appli-

ance maintenance set (Article no. 07921-000) specifically li-

censed for KETTLER Sports apparatus and available from the

Sport specialized trade.

■ Please ensure that liquids or perspiration never enter the machine

or the electronics.

■ This Rowing machine is an exercise machine that works inde-

pendence from stroke sequence (speed).

■ A slight production of noise at the bearing of the centrifugal mass

is due to the construction and has no negative effect upon ope-

ration.

■ The unit has a magnetic brake system.

Before assembling or using the unit, please read the following instructions carefully. They contain important information

for use and maintenance of the equipment as well as for your personal safety. Keep these instructions in a safe place

for maintenance purposes or for ordering spare parts.

GB Assembly Instructions

For Your Safety

■ The unit should be used only for its intended purpose, i.e. for

physical exercise by adult persons.

■ Any other use of the equipment is prohibited and may be dan-

gerous. The manufacturer cannot be held liable for damage or in-

jury caused by improper use of the equipment.

■ This unit has been designed in accordance with the latest stan-

dards of safety. Any features which may have been a possible

cause of injury have been avoided or made as safe as possible.

■ The unit complies with the EN 957-1, -7, class HB.

■ Incorrect repairs and structural modifications (e.g. removal or re-

placement of original parts) may endanger the safety of the user.

■ Damaged components may endanger your safety or reduce the

lifetime of the equipment. For this reason, worn or damaged

parts should be replaced immediately and the equipment taken

out of use until this has been done. Use only original KETTLER

spare parts.

■ In case of enquiry, please contact your KETTLER dealer.

■ If the equipment is in regular use, check all its components tho-

roughly every 1 – 2 months. Pay particular attention to the tight-

ness of bolts and nuts.This applies especially to the securing bolts

for saddle and handelbar.

■ Instruct persons using the equipment (in particular children) on

possible sources of danger during exercising.

■ Before beginning your program of exercise, consult your doctor

to ensure that you are ﬁt enough to use the equipment. Base your

program of exercise on the advice given by your doctor. Incorrect

or excessive exercise may damage your health!

■ Any interference with parts of the product that are not described

within the manual may cause damage, or endanger the person

using this machine. Extensive repairs must only be carried out by

KETTLER service staff or qualiﬁed personnel trained by KETTLER.

■ To ensure that the safety level is kept to the highest possible stan-

dard, determined by its construction, this product should be ser-

viced regulary (once a year) by specialist retailers.

■ Before use, always check all screws and plug-in connections as

well as respective safety devices fit correctly.

■ Caution: While assembly of the product keep off children’s reach

(Choking hazard - contains small parts).

■ Before beginning your first training session, familiarize yourself

thoroughly with all the functions and settings of the unit.

■ Always wear suitable shoes when using.

■ Before beginning your program of training, study the instructions

for training carefully.

■ Our products are subject to a constant innovative quality assu-

rance. We reserve the right to perform technical modifications.

■ Attention! The unit should be positioned in such a way that there

is a space of 100 cm on both sides and 150 cm behind it.

■ All electric appliances emit electromagnetic radiation when in

operation. Please do not leave especially radiation-intensive ap-

pliances (e.g. mobile telephones) directly next to the cockpit or

the electronic controlsystem as otherwise values displayed might

be distorted (e.g. pulse measurement).

WARNING! Heart rate monitoring systems may be inaccurate.

Over exercise may result in serious injury or death. If you feel

faint stop exercising immediately.

GB Assembly Instructions

Instructions for Assembly

■ Ensure that you have received all the parts required (see check

list) and that they are undamaged. Should you have any cause

for complaint, please contact your KETTLER dealer.

■ Before assembling the equipment, study the drawings carefully

and carry out the operations in the order shown by the diagrams.

The correct sequence is given in capital letters.

■ Please note that there is always a danger of injury when wor-

king with tools or doing manual work. Therefore please be ca-

reful when assembling this machine.

■ Ensure that your working area is free of possible sources of dan-

ger, for example don’t leave any tools lying around. Always dis-

pose packaging material in such a way that it may not cause

any danger. There is always a risk of suffocation if children play

with plastic bags!

■ The equipment must be assembled with due care by an adult per-

son. If in doubt call upon the help of a second person, if possi-

ble technically talented.

■ The fastening material required for each assembly step is shown

in the diagram inset. Use the fastening material exactly as in-

structed. The required tools are supplied with the equipment.

■ Bolt all the parts together loosely at first, and check that they have

been assembled correctly. Tighten the locknuts by hand until re-

sistance is felt, then use spanner to ﬁnally tighten nuts completely

against resistance (locking device). Then check that all screw con-

nections have been tightened firmly. Attention: once locknuts

have been unscrewed they no longer function correctly (the lok-

king device is destroyed), and must be replaced.

■ Please keep original packaging of this article, so that it may be

used for transport at a later date, if necessary.

List of spare parts page 25-27

When ordering spare parts, always state the full article number,

spare-partnumber, the quantity required and the S/N of the product

(see handling).

Example order: Art. no. 07985-670 / spare-part no. 10100009

/ 2 pieces / S/N ....................

Please keep original packaging of this article, so that it may be

used for transport at a later date, if necessary.

Goods may only be returned after prior arrangement and in (in-

ternal) packaging, which is safe for transportation, in the original

box if possible.

It is important to provide a detailed defect description / damage

report!

Important: spare part prices do not include fastening material; if fa-

stening material (bolts, nuts, washers etc.) is required, this should

be clearly stated on the order by adding the words „with fastening

material“.

Waste Disposal

KETTLER products are recyclable. At the end of its use-

ful life please dispose of this article correctly and safely

(local refuse sites).

KETTLER GB Ltd. · KETTLER House, Merse Road · North

Moons Moat · Redditch, Worcestershire B98 9HL

KETTLER International Inc. · 1355 London Bridge Road · Vir-

ginia Beach, VA 23453

http://www.kettler.de

USA

Page is loading ...

Messhilfe für Verschraubungsmaterial

Measuring help for screw connections

Gabarit pour système de serrae

Meethlp voor schroefmateraal

Ayuda para la medición del material de atornilladura

Misura per materiale di avvitamento

Wzornik do połączeń śrubowych

Checkliste (Packungsinhalt)

Checklist (contents of packaging) Liste de vérification (contenu de l’emballage) Checklijst (verpakkingsinhoud)

Lista de control (contenido del paquete) Lista di controllo (contenuto del pacco)

Lista kontrolna (zawartość opakowania)

1/1

Page is loading ...

M8x45

ø25

Benutzen Sie bei diesem Montageschritt geeignetes Unter-

legmaterial (z. B. Verpackung, Styropor, o. ä.) damit das

Gehäuse nicht verkratzt oder beschädigt wird.

Please, use suitable supporting material (such as packing

material, polystyrene or similar material) for this assembly

step in order to avoid a scratching or damaging of the hou-

sing.

Lors de cette phase de montage, utilisez du matériel de sup-

port approprié (p. ex. emballage, styropore ou similaire)

pour éviter que la boîte ne soit pas endommagée ou égra-

tignée.

Gebruik bij deze montagestap geschikt materiaal om onder

het apparaat te leggen (bijv. het verpakkingsmateriaal,

piepschuim of iets dergelijks), zodat het omhulset niet door

bijvoorbeeld krassen beschadigd wordt.

Durante este paso de montaje se recomienda colocar de-

bajo del aparato un material adecuado (p.e. el embalaje,

icopor etc.) para que no se rasguñe o dañe la envoltura.

Per questa sequenza di montaggio utilizzate del materiale

d’appoggio adatto (per es. imballaggio, polistirolo, o si-

mili) in modo che la carcassa non si graffi o danneggi.

Podczas tej operacji montażowej stosuj odpowiedni

podkład (na przykład opakowanie, styropian itp.), aby obu-

dowa nie zadrapała się względnie nie uległa uszkodzeniu.

3,9x13

A “klick”

Page is loading ...

Handhabungshinweise

Handling Utilisation Handleiding Aplicación Utilizzo Zastosowanie

Achtung! Falls der Sitz des Rudergerätes schwergängig ist,

bitte Schraube (A) etwas lösen, Sitz etwas nach oben ziehen

(B) und dabei Schraube (A) wieder fest anziehen.

Caution! If the seat of the rowing machine is stiff, please

loosen the screw (A) slightly, pull the seat a little upwards (B)

and, while doing so, tighten the screw (A) again.

Attention! Si la siège du rameur se déplace difficilement,

desserrez la vis (A) légèrement, tirez la siège un peu verse

le haut (B) et resserrez la vis (A).

Opgelet! Indien de zitting van het roeiapparaat stroef is,

draait u schroef (A) los, trekt de zitting iets naar boven (B)

en draait vervolgens schroef (A) weer stevig vast.

¡Atención! Si el asiento de la máquina de remar marcha

demasiado duro, suelte levemente el tornillo (A), tire el

asiento un poco hacia arriba (B) y al mismo tiempo apriete

de nuevo el tornillo (A).

Attenzione! Se la sede del timone è rigida, allentare leg-

germente la vite (A), sollevare leggermente la sede verso

l’alto (B) e poi serrare di nuovo la vite (A).

Uwaga! Jeżeli siedzenie urządzenia do wiosłowania po-

rusza się zbyt ciężko, proszę poluzować co nieco śrubę

(A), pociągnąć siedzenie trochę do góry (B) i przy tym po-

nownie mocno dokręcić śrubę (A).

Important: The guarantee does not cover worn-out batteries.

You should no longer put used batteries in domestic

waste. Please do your bit for the environment and return

your batteries to the trade or to the local authority pick-up

point so that the collected batteries can be properly dis-

posed of or recycled in an environment-friendly way.

Changement de piles

Un affichage de l'ordinateur faible ou éteint impose un change-

ment des piles. L'ordinateur est équipé de deux piles. Effectuez le

changement comme suit:

■ Enlevez le couvercle du logement des piles et remplacez-les par

deux piles neuves du type AA 1,5V.

■ Veillez au marquage au fond du logement lors de la mise en

place des piles.

■ En cas de dysfonctionnement après la remise en marche, enlevez

brièvement les piles et remettez-les ensuite.

Important: Les piles usées sont exclues des dispositions de garan-

tie.

Il est interdit de mettre les piles usées aux ordures ména-

gères. Merci de contribuer à la protection de l'environ-

nement et de rendre les piles usées soit au magasin soit

aux localités de reprise de la commune dans le but d'éli-

miner les piles collectées ou de les recycler de manière

non polluante.

Omwesseln van de Batterijen

Een zwakke of gewiste computerweergave maakt een batterijwis-

seling noodzakelijk. De computer werkt op 2 batterijen. Omwis-

seling van de batterijen gaat als volgt:

■ Verwijder het deksel van het batterijvak en vervang de batterijen

door twee nieuwe van het type AA 1,5V.

■ Let bij verwisseling van de batterijen op de tekens in het batte-

rijvak.

■ Komen er na verwisseling nog foutieve functies voor, haalt u dan

de batterijen nog eens uit het vak en duw ze weer terug.

Belangrijk: batterijen vallen niet onder de garantie.

Lege energiecellen mogen niet met het huisvuil mee.

Lever uw bijdrage aan het milieu en lever gebruikte bat-

terijen apart in bij de daarvoor aangewezen depots,

zodat de ingezamelde batterijen daarna naar behoren

vernietigd en milieuvriendelijk gerecycled kunnen worden.

Cambio de la pilas

Una indicación debil o inexistente en el monitor hace necesario

un cambio de pilas. El ordenador dispone de dos pilas. Efectúe el

cambio de pilas de la siguiente forma:

■ Retire la tapa de la caja de pilas y cambie las pilas usadas por

nuevas del tipo AA, 1,5V

■ Al poner las pilas observe la caracterización en el fondo de la

caja de las pilas.

■ Si después de ser puesto de nuevo en funcionamiento se produ-

jeran errores, desconecte brevemente las pilas y vuelva a co-

nectarlas.

Importante: Las pilas gastadas no est·n incluidas en la garantÌa.

No se deben echar las baterÌas energeticas gastadas en

la basura domestica. Por favor contribuya usted por su

parte a la protecciun del medio ambiente y deposite las

Batteriewechsel

Eine schwache oder erloschene Computeranzeige macht einen Bat-

terie wechsel erforderlich. Der Computer ist mit zwei Batterien aus-

gestattet. Nehmen Sie den Batteriewechsel wie folgt vor:

■ Nehmen Sie den Batteriefachdeckel ab und ersetzen Sie die Bat-

terien durch zwei neue vom Typ AA 1,5V.

■ Achten Sie beim Einsatz der Batterien auf die Kennzeichnung im

Batteriefachboden.

■ Sollte es nach dem Wiedereinschalten zu Fehlfunktionen kommen,

klem men Sie die Batterien noch einmal kurz ab und wieder an.

Wichtig: Aufgebrauchte Batterien fallen nicht unter die Garantie -

bestim mun gen.

Verbrauchte Energiezellen dürfen nicht mehr in den Haus-

müll .

Bitte leisten Sie Ihren Beitrag zum Umweltschutz und

geben Sie verbrauchte Batterien beim Handel oder bei

den Rücknahmestellen der Kommunen ab, damit die ge-

sammelten Batterien an schließend ordnungsgemäß be-

seitigt oder umweltverträglich recycelt werden können.

Battery change

A weak or an extinguished computer display makes a battery

change necessary. The computer is equipped with two batteries.

Perform the battery change as described below:

■ Remove the lid of the battery compartment and replace the bat-

teries by two new batteries of type AA 1,5V.

■ When inserting the batteries pay attention to the designation an

the bottom of the battery compartment.

■ Should there be any misoperation after switching on the compu-

ter again, shortly disconnect the batteries once again and re-in-

sert them.

Page is loading ...

Demontage des Computers im Reparaturfall

Detaching computer for repairs

Démontage de l’ordinateur pour réparation

Demontage van de computer voor reparatie

Desmontaje de la computadora en casa de la reparación

Smontaggio del computer nel caso di riparazioni

Demontaż komputera w przypadku naprawy

Geben Sie bei Ersatzteilbestellungen bitte die vollständige

Artikelnummer, die Ersatzteilnummer, die benötigte Stück-

zahl und die Seriennummer des Gerätes an.

When ordering spare parts, always state the full article num-

ber, spare-partnumber, the quantity required and the S/N of

the product.

En cas de commande de pièces de rechange, nous vous

prions de mentionner la référence article, le numéro de

pièce de rechange, la quantité demandée et le numéro de

série de l’appareil.

Vermeld bij de onderdelenbestellingen a.u.b. het volledige

artikelnummer, het onderdeelnummer, het benodigde aan-

tal en het serienummer van het apparaat.

Indicar con los pedidos de piezas de repuesto el número

completo del artículo, el número de la pieza de repuesto,

las unidades solicitadas y el número de serie del aparato.

Per l’ordinazione di parti di ricambio indicate il completo

numero di articolo, della parte di ricambio, il numero di

unit necessario nonchè il numero di serie dell’apparecchio.

Przy zamawianiu części zamiennych proszę podawać kom-

pletny numer artykułu, numer części zamiennej i numer serii

urządzenia.

Ersatzteilbestellung

Spare parts order Commande de pièces de rechange Bestelling van reserveonderdelen

Pedido de recambios Ordine di pezzi di ricambio Zamówiene części zamiennych

Rudermaschine 07985-670 07985-679

Pos.- Coach LS qty Europa USA

Nr Bezeichnung escription Stück Bestell-Nr. spare part #

1 Gehäuseeinheit Frame, base 1 94317440 94317440

2 Fußhülse (14-08586) Foot tube 1 94317549 94317549

3 Bowdenzug mit Verstellhebel montiert Tension cable unit 1 94314107 94314107

4 Drehknopf (kpl. mit Schraube + Stopfen) Knob with shaft, right 1 94314231 94314231

5 6-kant Schraube M8x145 Bolt, hex m 8x145 1 10205145 10205145

6 Verstellrad links (2016) Knob, left 1 94314244 94314244

7 Stopfen ø42 mm Plug 42 mm 1 10100079 10100079

8 Distanzrohr A3 Spacer sleeve A3 1 97200537 97200537

Page is loading ...

Ersatzteilbestellung

Rudermaschine 07985-670 07985-679

Pos.- Coach LS qty Europa USA

Nr Bezeichnung escription Stück Bestell-Nr. spare part #

9 Trägerblech (BD 1469) Carrier plate 1 97200036 97200036

10 Zeiger 0-10 (1728) Scale, resistance 1 91170207 91170207

11 Befestigungswinkel (3-4266) Bearing plate 1 97201826 97201826

12 Magnethalter kpl. Montiert Flywheel resistance magnet with 5 magnets 1 91170364-40 91170364-40

13 Magnetsegment Magnet 5 67000170 67000170

14 Verstell-Lasche (BD 1329B) Tabaxle, resistance shoe 1 97200045 97200045

15 Pendelhalter (3-3846) Triparm, stroke count 165 mm long 1 97201825 97201825

16 Magnet M 3101 Magnet sensor M 3101 1 67000146 67000146

17 Seilrolle Nr. 4 (2097) Pulley, cord Nr. 4 2 98585016 98585016

18 Buchse (2098) Bushing 4 70130045 70130045

19 Lasche (4-5909) Tabbrace, triparm pulley 1 97200249 97200249

20 Zugfeder (4-5910) Spring 1 25605910 25605910

21 Seilrolle Nr. 1 (1896) Pulley, cord Nr. 1 1 98585018 98585018

22 Distanzrohr A983 Spacer sleeve A983 1 97201494 97201494

23 Distanzrohr A203 Spacer sleeve A203 1 97200456 97200456

24 Schwungrad kpl. montiert Fly wheel 1 91140293 91140293

25 Griff 25x2x400 mm kpl. Pullbar, 25x400 mm with grip 1 91210359-40 91210359-40

26 Soft-Grip SW Soft-Grip black 1 10118010 10118010

27 Stopfen ø30 mm Plug, 30 mm 2 10100149 10100149

28 Lagerblech (BD 1480) montiert Support bracket 1 94315123 94315123

29 Zugfeder (4-5973-a) Tension spring 1 25605973 25605973

30 Verkleidung rechts (4745) mit Einschubteil Panel, right 1 70125942 70125942

31 Verkleidung links (4746) mit Einschubteil Panel, left 1 70125943 70125943

32 Abdeckung (4195) Covering (4195) 1 70128898 70128898

33 Ablageeinsatz (3625) Backstop, pullbar 1 70132652 70132652

34 Computer ST 2500-4 geprüft Computer St 2500-4 1 94314232 94314233

35 Batteriefachdeckel (3620) Covering for battery pack 1 70126674 70126674

36 Elektor-Aufsatz (3591) für Verkleidung Housing 1 70132649 70132649

37 Hinterbau Main tube 1 94317459 94317459

38 Stopfen 40x25 Plug40x25 mm 2 10100009 10100009

39 Scheibe mit Zapfen ø40 mm Axle bumper 2 10122073 10122073

40 Stopfen 60x40 mm Plug, 60x40 mm 1 10100092 10100092

41 Abdeckung Fuß (4576) Foot covering 1 70128899 70128899

42 Bodenschoner (0738) Foot 1 70132175 70132175

43 Sitzführung *2007* Guiding tubes for seat 1 97100574 97100574

44 Kappe (3876) Endcap (3876) 4 70132297 70132297

45 Sitzträgerblech Seat carrier plate 1 94318045 94318045

46 Distanzrohr A948 mit Laufrolle (4313) Spacer sleeve A948 with Roller (4313) 4 94317389 94317389

47 Laufrolle (4313) Roller (4313) 4 14165029 14165029

48 Sitz f. Rudergerät 8508/8067 SW Seat 1 72591160 72591160

49 Bodenrohr 80/33 Crossmember, frame 80/33 1 91111951-40 91111951-40

50 Rollenschoner rechts Foot roller right 1 91170579 91170579

51 Einsteckteil (2389) Plate for foot roller 2 70127565 70127565

52 Rollenschoner links Foot roller left 1 91170580 91170580

53 Trittplatte (BD1481) Kickplate, front base 1 94314110 94314110

54 Polsterplatte (4-2025) Back cushion 1 94316200 94316200

55 Aufnahme Liegebrett (4744) Brace for seat 2 70125945 70125945

56 Filzplatte 130x 70 mm Felt plate 130x70 mm 2 12510006 12510006

57 Fußstütze rechts (4512) Foot plate, right 1 70129035 70129035

58 Fußstütze links (4513) Foot plate, left 1 70129036 70129036

59 Bodenschoner (1696) Plug for footplate 2 70127930 70127930

60 Klettband m. Öse Rudergerät Strap for footplate 2 42108006 42108006

61 Pedalachse A791 Rod, pedal axle A791 1 97201560 97201560

62 Pedalanschlag A792 Rod, pedal rest A792 1 97201561 97201561

63 Kleinteilbeutel o. Abb. Hardware Bag (w/o fig.) 1 94317442 94317442

64 Distanzrohr A589 Distance tube A589 2 97200558 97200558

65 Distanzrohr A953 Distance tube A953 2 97201486 97201486

66 Laufrolle (4715) Roller (4715) 2 98585083 98585083

67 Hülse A973 Spacer sleeve A973 2 97201489 97201489

68 Achse für Lauwagen Axle for seat carrier plate 1 11300121 11300121

69 POLAR Brustgurt T34 ohne Plug POLAR cheast strap (w/o fig.) 1 67002000 67002000

Page is loading ...

Kettler COACH LS 07985-670 Assembly Instructions Manual

Brand: Kettler

Model: COACH LS 07985-670

Type: Assembly Instructions Manual

This manual is also suitable for

COACH LS 07985-679

Download PDF

report

Kettler COACH LS 07985-670 Assembly Instructions Manual

This manual is also suitable for

Kettler COACH LS 07985-670 Assembly Instructions Manual

in other languages

Related papers

Other documents