Serene DAC-202 Operating instructions
- Category
- Coaxial cables
- Type
- Operating instructions
Serene DAC-202 is a device that allows you to connect your TV to your TV listening system. It comes with the following components:
- AC Adapter
- TV Digital Connector
- Digital Optical Cord
To set up the device, follow these steps:
- Turn off all related audio and video devices before installation.
- Connect the connection cable packaged with the TV Listening system to the AUDIO port located on the back of the TV Listening system.
- Plug the other end of the connection cable into the black portion of the audio RCA adapter Y-cord
- Slide the switch on the side of the DAC-202 to OPTICAL
Serene DAC-202 is a device that allows you to connect your TV to your TV listening system. It comes with the following components:
- AC Adapter
- TV Digital Connector
- Digital Optical Cord
To set up the device, follow these steps:
- Turn off all related audio and video devices before installation.
- Connect the connection cable packaged with the TV Listening system to the AUDIO port located on the back of the TV Listening system.
- Plug the other end of the connection cable into the black portion of the audio RCA adapter Y-cord
- Slide the switch on the side of the DAC-202 to OPTICAL
Oaktree Products, Inc
800.347.1960
otp@oaktreeproducts.com
WHEN BACK OF TELEVISION LOOKS SOMETHING LIKE THIS:
IT IS NECESSARY TO PURCHASE THE DAC-202 TO MAKE YOUR TV
LISTENING SYSTEM WORK
The DAC-202 COMES WITH THE FOLLOWING COMPONENTS:
TV missing
traditional red,
white and yellow
RCA cable
connections
labeled AUDIO OUT
(note: AV OUT is NOT
same as AUDIO OUT)
TV Digital Connector
AC Adapter
Digital Optical Cord*
*remove plastic tip covers from optical cord plugs
Oaktree Products, Inc
800.347.1960
otp@oaktreeproducts.com
SETTING UP TV LISTENING DEVICE TO TV USING DAC-202
Note: Illustrations are approximations of set up as each TV Listening system will
have similar components that may vary slightly
Turn off all related audio and video devices before installation. Reactivate those
devices only after all connections are complete.
TV-LISTENING DEVICE
1. Plug the connection cable packaged with the TV Listening system to the
AUDIO port located on the back of the TV Listening system. Follow the
instructions outlined in the TV-Listening system manual; in this particular
example, the blue end of the connection cord plugs into the AUDIO port on
the back of the base
2. Plug the other end of the connection cable shown above in the black portion
of the audio RCA adapter Y-cord
Oaktree Products, Inc
800.347.1960
otp@oaktreeproducts.com
CONNECTING TV-LISTENING DEVICE TO DAC-202
3. Slide the switch on the side of the DAC-202 to OPTICAL
4. Connect RCA ends of audio cable from above (packaged with TV Listening
system) to the AUDIO R-L output on the back of the DAC-202, making sure
red plug connects to red port, and white plug connects to white port
CONNECTING DAC-202 TO YOUR TV:
5. Locate the OPTICAL port on the back of the TV. It looks like this:
6. NOTE: it may be necessary to remove a rubber flap that covers the port as
shown below:
Oaktree Products, Inc
800.347.1960
otp@oaktreeproducts.com
7. Connect one end of the Digital Optical Cord (packaged with the DAC-202) in
the black U-shaped optical cable port (not the coaxial port with protruding
silver one) located on the other end of the DAC-202
8. Plug the other end into the OPTICAL cable port located on the back of the TV
9. Connect the AC Adapter (packaged with DAC-202) to the DC IN port located
on the TV Digital Connector and plug the other end in a wall outlet.
YOU ARE NOW READY TO ENJOY YOUR TV LISTENING DEVICE
Other end plugs into OPTICAL
cable port in back of TV
-
1
-
2
-
3
-
4
Serene DAC-202 Operating instructions
- Category
- Coaxial cables
- Type
- Operating instructions
Serene DAC-202 is a device that allows you to connect your TV to your TV listening system. It comes with the following components:
- AC Adapter
- TV Digital Connector
- Digital Optical Cord
To set up the device, follow these steps:
- Turn off all related audio and video devices before installation.
- Connect the connection cable packaged with the TV Listening system to the AUDIO port located on the back of the TV Listening system.
- Plug the other end of the connection cable into the black portion of the audio RCA adapter Y-cord
- Slide the switch on the side of the DAC-202 to OPTICAL
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Hyundai H-HT5115-N User manual
-
NAD M32 Owner's manual
-
Oppo HA-1 User manual
-
NAD M12 Owner's manual
-
TEAC DV-H500 User manual
-
Slim Devices SLIM DEVICES User manual
-
NAD M33 BluOS Streaming DAC Amplifier User manual
-
Pioneer HTP-204 User manual
-
ONKYO RF-EX6 User manual
-
TV Ears Wireless Speaker User manual
