Viper 7756V Owner's manual

[ Owners-Manual ]

MODEL

7756V

Inhalt

Getting Started ..............................................................8

• Charging the remote control ........................................... 8

• Keystousingthismanual ................................................. 9

Responder LC Remote Control ...................................10

Control Center .............................................................11

Status Screen Icons .....................................................12

Using your System ......................................................15

• Commands and Confirmations ....................................... 15

• PerformingCommands ................................................... 15

• ResponderLCCommandtable ................................. 16 / 17

• FaultConditionAlerts ..................................................... 17

Basic Commands (Direct Access) ................................18

• Arm .................................................................................. 18

 • ToArmandPanic ............................................................ 18

 • Disarm .............................................................................. 18

• AUX/Trunk ....................................................................... 19

• RemoteStart(only5606V) ............................................. 19

Advanced Commands: (Level 1) .................................20

• SilentArm ........................................................................ 20

• SilentDisarm ................................................................... 20

 • AUX1 ............................................................................... 20

• RuntimeReset(only5606V) ........................................... 20

CAR SECURITY ICARAUDIOICARMEDIA

• TempRequest .................................................................. 21

Advanced Commands: (Level 2) .................................22

• SensorBypass .................................................................. 22

• RemoteValet ................................................................... 22

• AUX2 ............................................................................... 22

• TimerStart(only5606V) ................................................. 23

• RuntimeRemaining(only5606V) .................................. 23

Advanced Commands: (Level 3) .................................24

• SensorSilentArm ............................................................ 24

• Carfinder ......................................................................... 24

• AUX3 ............................................................................... 24

• SmartStart(only5606V) ................................................. 24

 • AlarmReport ................................................................... 25

Advanced Commands: (Level 4) .................................26

• FullSilentArm ................................................................. 26

• AUX4 ............................................................................... 26

• Defogger(only5606V) ................................................... 26

Responder LC Configuration ......................................27

• Navigatingmenusandoptions ...................................... 27

• Buttonoperation ............................................................ 27

• Accessmenuitems .......................................................... 28

Main Menu ...................................................................29

• SetupRemotemenu ....................................................... 29

• SensorAdjust ................................................................... 32

• PairRemote ..................................................................... 33

• Demomode ..................................................................... 34

• PowerOff ........................................................................ 35

• Exit ................................................................................... 35

1-way Companion Remote Control ......................36 / 37

• Usingthe1waycompanionremote .............................. 37

• AccessingCommands ...................................................... 37

• ButtonAutoLock ............................................................ 38

• CarSelect ......................................................................... 38

• Programming .................................................................. 38

Alarm Features ............................................................41

• NormalArmProtection .................................................. 41

• SensorSilentArmprotection ......................................... 42

• FullSilentArmProtection .............................................. 42

• SensorWarn-awayMessages ......................................... 42

• FullTriggerMessages ...................................................... 42

• EmergencyOverride ....................................................... 42

• TriggerZoneFaultReport .............................................. 43

• AlarmReportwhendisarming ....................................... 44

 • TableofZones ................................................................. 44

 • AlarmReportwhenrequested ....................................... 45

• NuisancePrevention(NPC) ............................................. 45

Remote Start Features (only 5606V) ..........................46

• KeyTakeover ................................................................... 46

• RemoteStartSafe-lock ................................................... 46

• DisablingRemoteStart ................................................... 46

• AdvancedStart ................................................................ 47

• TemperatureReporting .................................................. 49

 • RemoteStartTime-outAlert .......................................... 49

• PitStopMode .................................................................. 49

• ManualTransmissionStart(MTSmode) ........................ 50

• TurboTimerMode .......................................................... 51

• RemoteStartError .......................................................... 52

Remote and System Operations .................................54

• PassiveArming ................................................................ 54

• AutoRe-arming ............................................................... 54

• OnetimeBypass ............................................................... 54

• ValetMode ...................................................................... 55

• PowerSave ...................................................................... 55

• RapidResume .................................................................. 56

• AutomaticRemoteUpdates ........................................... 56

• OutofRange ................................................................... 56

• NoRemoteOutput ......................................................... 56

• FeaturenotAvailable ..................................................... 57

• ResetnachTiefentladung ............................................... 57

System Expansion Options .........................................58

• Controllingtwovehicles(CarSelect) ............................. 58

• Ownerrecognition .......................................................... 58

• Comfortclosure ............................................................... 58

• Alarmoutputduration ................................................... 58

• ArmingandWarn-awaychirpcontrol ........................... 59

• Driverdoorpriorityunlocking ....................................... 59

• AuxiliaryChannels .......................................................... 59

Battery Information (Responder LC) .........................60

• LowBattery ..................................................................... 60

• BatteryLife ...................................................................... 61

Battery Information (1-Way) ......................................62

• BatteryReplacement ...................................................... 62

• BatteryDisposal .............................................................. 62

Glossary of Terms ........................................................63

Note!

Ifthebatteryisexcessivelydepletedwhencharging,func-

tionalitymaybedelayedwhileitchargestotheminimum

voltagerequiredtooperatethedisplay,afterwhichnor-

mal charging resumes.

Keys to using this manual

 Specificactions(inboldtype)andstyleconventionsareused

consistentlythroughoutthismanual,theyareasfollows:

• Press:impliespushinginandreleasingabutton.

• Hold:isusedafterPressactionswhenabuttonneedstobe

held in position for an extended period of time, typically

severalseconds.

• „ARMED“: this style denotes the text which appears in the

textfieldportionoftheDisplayduringoperationsdescribed

inthemanual.Ifthetextstringistoolongforthetextfield,

itthenplaysandloopssequentiallywordbyword.

• Italicized words denote section/sub headings in this guide

andcanbelocatedthroughthetableofcontents.

• Anasterisk (*)whenusedafter awordor phrase denotes

thatadditionaldetailscanbefoundinrelatedsectionsusu-

allynotedatthebottomofthepageorendofthesection.

Getting Started

 Your Responder LC remote is powered by an internal

rechargeablebatterythatcanonlybeservicedbyanautho-

rizedDirecteddealer.Duetotransitandstoragetimeprior

toyourpurchase,thebatterychargemayhavedepleted.To

ensureproperoperation,checkthebatterylevelandifnot

fullycharged,usetheprovidedcabletoconnecttotheUSB

port on a computer. See “Battery Information (Responder

LC)” on page 49 and “Status Screen Icons” on page 8 for

moreinformationaboutthebattery.

Charging the remote control

• PlugtheUSB end of the provided USB cableintotheUSB

portonacomputer.Insertthemini-USBconnectorintothe

mini-USBportlocatedonthesideoftheremotecontrol.The

textfieldwilldisplay„CHARGE“ to indicate the remote con-

trol is charging (The remote remains operational while

chargingandcancommandthesystem).

• Oncefullychargedthetextfieldwilldisplay„FULL“.

• The remote control is then ready for use. Disconnect the

cablefromtheremotecontrolendfirst.

1110

Responder LC Remote Control

Feature Description

InternalAntenna Usedfortransmittingandreceivinginformation

Display

Status screen-theupperportionofthedisplay

containsstatusiconsfortheSystem,Siren,Alarm

zones,RemoteStartandRemoteControl.

Text field -thelowerportionofdisplay-shows

theClock,RuntimeorTemperatureduringRe-

moteStart,aswellasCommandconfirmations,

Pagemessagesandprogrammingmenus

Command

buttons(4)

Usedtoperformarming,disarming,auxiliary

channel and remote start commands

Functionbutton

Usedtoaccessfunctionlevelsforcommands,

configurationmenusforprogramming,Car

Selection,andtorequestreports.

Mini-USBPort

TheUSBcableplugsintothisport(locatedon

remotecontrolside).

Control Center

 The Control Center,typically located on the upperpartof

thefrontwindshieldsendsandreceivescommandsormes-

sagestoandfromyoursystem.

 Itconsistsof:

• TheIn-vehiclesystemantenna,for2waycommunication.

• TheStatusLED,asavisualindicatorofthesystem’sstatus.

• TheControlbutton,forplacingthesystemintoValetMode*

andtoperformtheEmergencyOverride**operation.

 * See“RemoteandSystemOperations”onpage54fordetails.

** See“AlarmFeatures”onpage41fordetails.

1312

Symbol Beschreibung

Remote

Start

(5606V)

Remotestartisactive,theengineis

running.

TimerStartOn;RemoteStartOn.Without

arrow:TimerStartenabled:RemoteStartOff

SmartStartOn;RemoteStartOn.Without

arrow:SmartStartOn;RemoteStartOff.

ManualTransmissionStartmodeis

enabled,theenginecanbestarted

Displaysthevehicleinteriortemperature

OnduringRemoteStartafterperform-

ingtheDefoggerOncommand

Zone

Status

OnduringWarn-awayandFullTrigger

messageoutput

OnduringTrunkZoneFullTriggerout-

putandAux/Trunkchannelactivation

OnduringFaultReporttoindicatethe

Trunkisopenandbypassedwhenarming

OnduringaSensorZoneFullTriggeroutput

OnduringFaultReporttoindicateaSen-

sorisactiveandbypassedwhenarming

OnduringtheDoorZoneFullTriggeroutput

OnduringFaultReporttoindicatea

Doorisopenandbypassedwhenarming

OnduringaHoodZoneFullTriggeroutput

OnduringFaultReporttoindicatethe

Hoodisopenandbypassedwhenarming

Status Screen Icons

ALL

 Thetablebelowdescribesallthestatusscreenicons.

Symbol Beschreibung

System

Status

Armed:ThesystemisArmed,thealarm

isenabled.

Locked:ThesystemisLockedinValet,

thealarmisdisabled.

Disarmed:ThesystemisDisarmed,the

alarmisdisabled.

Unlocked:ThesystemisUnlockedin

Valet,thealarmisdisabled.

Siren

Status

Sirenisdisabledforsensortriggers;remote

ispagedforalltriggers(SensorSilentArm).

Sirenisdisabledforalltriggers;remote

ispagedforalltriggers(FullSilentArm).

1514

Symbol Beschreibung

Remote

Control

Status

On when remote is set to command the

systemprogrammedasCar1*

On when remote is set to command the

systemprogrammedasCar2*

BarsindicatebatterylevelisFull,¾,½,¼

orEmpty

On while the remote control is transmit-

ting a command

Onwhiletheremotecontrolisreceiving

a message

OnwithOutofRangefaulttoneto

indicatetheremotefailedtoreceivea

command confirmation

Pageron:Theremotewillwakeupto

listen for messages

Pageroff:Theremotewillnotwakeup

to listen for messages

TheremotewillVibratewhenmessages

arereceived

TheremotewillemitBeepsandTones

whenmessagesarereceived

DisplaystheClock,Runtime,Tempera-

ture,messagetextandfeaturemenus

OnaftertheGarageOpen**message

hasbeenreceived.

OnaftertheGarageClosed**message

hasbeenreceived.

Using your System

Commands and Confirmations

 Commands, Basic or Advanced, are used to activate system fea-

turesandare performed by pressing one of theCommandbut-

tons. Basic commands control the most often used security and

remote start features while Advanced commands control more

specializedfeaturesandrequestreports.ConfirmationsforBasicor

Advancedcommandsareindicatedfirstbysirenchirpsandparking

lightflashes,andthenbyText,Iconsandbeepsortonesonthere-

motecontrol.Adescriptionofeachfeatureconfirmationisfound

inthefollowingBasiccommandandAdvancedcommandsections.

Performing Commands

 PerformBasiccommandsbypressingoneofthecommand

buttonswhileintheDirectAccesslevel.Directaccessisavail-

ablewhilethetextfielddisplaystheClock,Temperatureor

Runtime. Perform Advanced commands by first accessing

one of the Function Levels and then pressing one of the

commandbuttonswhilewithinalevel.FunctionLevelsare

availablewhenthetextfielddisplaysLEVEL1,2,3or4.

Advanced command example: Silent Arm

• Press the

-button once to access Function Level 1, the

textfieldwilldisplay„LEVEL 1“.

• Pressthe

-buttonwhile„LEVEL 1“textisstillontoperform

theSilentArmcommand.

• TheResponder LCremotewill display„SILENTARMED“in

thetextfieldandupdatethestatusscreenicons.

 * ThisiconnotpresentuntiltheCar2isturnedonintheSetupRemoteconfiguration

menu.

 ** Thisiconnotpresentuntiltheremoteispairedwithanoptionalgaragedooropener

1716

Responder LC Command table

Button Direct Access

x1 LEVEL 1

x2 LEVEL 2

x3 LEVEL 3

x4 LEVEL 4

Arm/Lock(Panic) SilentArm SensorBypass SensorSilentArm FullSilentArm

Disarm/Unlock SilentDisarm RemoteValet CarFinder

RemoteStart RuntimeReset TimerStart SmartStart Defogger

Aux/Trunk AUX1 AUX2 AUX3 AUX4

AdvanceLevelChangeCar(3s),

Enterprogramming(8s)

TemperatureCheck RuntimeRemaining AlarmReport

Fault Condition Alerts

If,whenperformingacommand,aconditionexiststhatdoes

notallowactivationofanAlarmfeature*orRemoteStartfea-

ture**,the„NOT AVAILABLE“ or „REMOTE START ERROR“text

andafaulttonewillplay.

 * Alarmfeaturenotavailablewhenthesystemstatusisincorrectuponreceivingthe

  command.(Example:Sensorbypasscommandisreceivedwhendisarmed).Referto

  thenotesincludedinthefollowingcommanddescriptionsthataddressthesefaults

  orgoto“FeaturenotAvailable”onpage57formoredetails.

 ** RemoteStart(only5606V)featurenotavailablewhentheRemoteStartstatusisin

  correct upon receiving the command. (Example: Runtime reset command received

  whenremotestartisoff).Refertothenotesincludedinthecommanddescriptions

that address.

  Thesefaultsorgoto“RemoteStartError”onpage52formoredetails.

1918

AUX/Trunk – Press and hold

 TheTrunkopens(ifconnected)whenthisbuttonispressed

for2seconds.The„TRUNK“textandtonesplaytoconfirm.

Remote Start (only 5606V) – Press and release

 Activates(orifOn,deactivates)theremotestarter.Theen-

gine and parking lights turn On and the „REMOTE START

ON“textandtonesplay,ortheengineandparkinglights

turn Off and the „REMOTE START OFF“textandtonesplay

toconfirm,theRemoteStartstatusiconsupdate.

 The

icon will display in the status screen and the text

fieldwilldisplaytheRuntime,TemperatureorClockaspro-

grammed.IfRemoteStartfailstoactivate,„REMOTE START

ERROR“textandafaulttoneplaywhiletheparkinglights

flashtoidentifythereason.***

Basic Commands (Direct Access)

Arm – Press and release

 The alarm arms, doors lock (if connected), and the siren

chirpsandparkinglightsflashonce.The„ARMED“textand

beepsplaytoconfirmandtheSystemStatusIconsupdate.If

Valetmode*isOn,thedoorslockandthe „VALET“textand

toneplay.ExitValetmodetoarmthealarmnormally.

 Ifatriggerzonefaultisdetectedthesirenchirpsonceagain

andtheTriggerZoneFaultreport**plays.

To Arm and Panic – Press and hold

 The alarm Arms (or Locks in Valet) and, after 2 seconds,

soundsthesirenandflashestheparkinglights.The„PANIC“

textandsirentonesplaytoconfirm.Pressthe

but-

tontostoptheoutput.

Disarm – Press and release

 The alarm disarms, doors unlock (if connected), and the

siren chirps and parking lights flash twice. The „DISARM“

textandbeepsplaytoconfirmandthesystemstatusicons

update. If Valet mode* is On, the doors unlock and the

„VALET“textandtoneplay.

 Morethan2sirenchirpsandremotebeepsindicateatrigger

hasoccurred.The„DISARM“textisreplacedbythe Alarm

report.**

 * See“RemoteandSystemOperations”onpage54fordetails.

** See“AlarmFeatures”onpage41fordetails.

***See“RemoteStartError”onpage52fordetails.

  ForManualtransmissionvehiclessee“ManualTransmissionStart(MTSmode)”on

  page50formoredetails.

2120

Advanced Commands: (Level 1)

 Pressandreleasethe

buttononetimefirst,beforepressing

oneofthefollowingcommandbuttons.

Silent Arm – Press and release

 The alarm arms, doors lock (if connected), and the parking

lightsflash once. The „SILENT ARMED“textplaysto confirm

and the System Status icons update. Valetmode* or Trigger

ZoneFaultreport**messagesmaybereceived.

Silent Disarm – Press and release

 Thealarmdisarms,doorsunlock(ifconnected),andthepark-

inglightsflashtwice.The„SILENT DISARM“textplaystocon-

firmandtheSystemStatusiconsupdate.TheAlarmreport**

mayreplacetheSilentDisarmtext.

AUX 1 – Press and release

 Activates(orifOn,deactivates)theAux1output.The„AUX

CHANNEL“textandOntonesorOfftonesplaytoconfirm.

Runtime Reset (only 5606V) – Press and release

 If more time is needed while remote start is active, runtime

reset will reset the runtime counter to the pre-programmed

setting. The „RUNTIME“ text and tones play to confirm. The

textfieldwillupdateifsettodisplayruntime.

Note!

RemoteStartmustbeOntousethisfeature.

Temp Request – Press and hold the

-button

 Requests the vehicle’s interior temperature and temporarily

displaysitviastatusscreenicon andtextfield.

 * See“RemoteandSystemOperations”onpage54fordetails.

 ** See“AlarmFeatures”onpage41fordetails.

2322

CHANNEL“ text and On tones or Off tones play to confirm.

Timer Start** (only 5606V) – Press and release

 Activates (or if On, deactivates) Timer Start. The parking

lightsflashquicklyfourtimesforOnandslowlyfourtimes

for Off. The „TIMER START ON“ or „TIMER START OFF“

textandbeepsplaytoconfirmandtheRemotestartstatus

iconsupdate.

Note!

SystemneedstobearmedorTimerStartwillnotstartthe

engine.

Runtime Remaining (only 5606V) – Press and hold

the

button

 RequeststheremainingRemotestartruntimeandtemporarily

displaysitinthetextfield.

Note!

RemoteStartmustbeOntousethisfeature.

Advanced Commands: (Level 2)

 Press and release the

button two times first, before

pressingoneofthefollowingcommandbuttons.

Sensor Bypass – Press and release

 Theparkinglightsflasheachtimethiscommandisreceived

to indicate the Sensor bypass type. Two flashes indicates

sensorWarnawayzonesarebypassed.„BYPASS WARN“,one

beepandonefaulttoneplaytoconfirm.3flashesindicates

sensorWarn-awayandFullTriggerzonesarebypassed.„BY-

PASS FULL“,onebeepandtwofaulttoneplaytoconfirm.

OneflashindicatessensorbypassisOff,„BYPASS OFF“ and

onebeepplaytoconfirm.

Note!

SystemneedstobearmedtoperformSensorBypass.

PerformarmcommandanytimetoturnSensorBypassOff.

Remote Valet* – Press and release

 Enters (or if On, exits) ValetMode. The „VALET“ text and

beeps(oneforOn,twoforOff)playtoconfirmandtheSys-

temStatusiconsupdate.SeeValetModeformoredetails

AUX 2 – Press and release

 Activates(orifOn,deactivates)theAux2output.The„AUX

 * See“ValetMode”onpage55formoredetails.

 ** See“AdvancedStart”onpage47formoredetails.

2524

Note!

SystemneedstobearmedorSmartStartwillnotstartthe

engine.

Alarm Report* – Press and hold the

button

 Requestsareportofthemostrecenttriggersandtemporarily

displaysitinthetextfield.Thereportclearswhentheignition

is turned on.

Advanced Commands: (Level 3)

Press and release the

button three times first, before

pressingoneofthefollowingcommandbuttons.

Sensor Silent Arm* – Press and release

 The alarm arms, doors lock, the siren chirps and parking

lightsflashthreetimes.The„SENSOR SILENT ARM“textand

beepsplaytoconfirmandtheSystemandSirenStatusicons

update.

Car finder – Press and release

 Thesirenemitsonelongchirpandtheparkinglightsflash

for 10 seconds. The „CAR FINDER“ text and beeps play to

confirm.Theparkinglightflashesstopifarmedordisarmed

whileCarFinderisinprogress.

AUX 3 – Press and release

 Activates(orifOn,deactivates)theAux3output.The„AUX

CHANNEL“ textandOntonesorOfftonesplaytoconfirm.

Smart Start** (only 5606V) – Press and release

 Activates (or if On, deactivates) Smart Start. The parking

lightsflashquicklyfivetimesforOnandslowlyfivetimesfor

Off.The„SMART START ON“ or „SMART START OFF“,text

andbeepsplaytoconfirmandtheRemotestartstatusicons

update.

 * See“AlarmFeatures”onpage41formoredetails.

 ** See“AdvancedStart”onpage47formoredetails.

2726

Responder LC Conﬁguration

 Operations of the Responder LC and how it communicates

messages are set in the configuration Main Menu.

Navigating menus and options

 Navigating menus and features, changing options, and

exiting are performed using the remote control buttons.

Thefollowinginstructionsdiscusshowtoaccessandconfig-

ure the settings.

Button operation

• To access menus, set options, and to perform actions that

aredisplayedinthetextfield,usethe

button.

• Toscroll themenulistsinthe textfielduse the

buttons.

 Toexitconfiguration:usethe

buttons.

Access menu items

• Pressandholdthe

buttonfor8seconds,theremotewill

beeponce,„MAIN MENU“isdisplayed.(IfCar2ison,ignore

theCarSelecttextandbeepafterthreeseconds).

• Releasethe

buttontodisplaytheMainMenuitemlist,

Advanced Commands: (Level 4)

 Press and release the

button four times first, before

pressingoneofthefollowingcommandbuttons.

Full Silent Arm* – Press and release

 The alarm arms, doors lock, and the siren chirps and parking

lightsflash4times.The„FULL SILENT ARM“textandbeepsplay

toconfirmandtheSystemandSirenStatusiconsupdate.

AUX 4 – Press and release

 Activates(orifOn,deactivates)theAux4output.The„AUX

CHANNEL“textandOntonesorOfftonesplaytoconfirm.

Defogger** (only 5606V) – Press and release

 Activates the vehicle Defogger circuit (if connected) while Re-

moteStartisactivated.The„DEFOG ON“textandbeepsplayto

confirmandtheRemote Start status icons update. For conve-

nience,theDefoggercircuitwillalsoautomaticallyactivate10

secondsafterremotestartingifthetemperatureisbelow55°F.

Note!

RemoteStartmustbeactivetousethisfeature.

 * See“AlarmFeatures”onpage41formoredetails.

 ** ThisfeaturemustbeinstalledandturnedonbyanauthorizedDirecteddealer.

2928

„SETUP REMOTE“isdisplayed.

• TheMainMenuhasbeenaccessedandconfiguringcanbe-

gin.UsethefollowingprocesstoviewtheMainMenufea-

tures,optionsandsettingsinthe textfield. Thefollowing

actions are commonly used throughout the configuration

operation.

 • Pressthe

buttonstochangethefeatureoropti

 onthatisdisplayedinthetextfield.

 • Pressthe

buttontochoosethefeatureinthetextfield

 andviewitsoptions.Pressitwhenthedesiredfeatureor

 optionisinthetextfieldtosetitasthenewsetting.

Main Menu

 The following Main Menu list of features is available for

configuration of the remote control.

Setup Remote menu

• Keypad Lock

 Options:„OFF“,„AUTO“

 When„OFF“,thebuttonsdonotlockandalwaysperforma

commandwhenpressed.Whensetto„AUTO“,theremote

buttonslockaftera20secondlapsebetweenbuttonspress-

estopreventunintentionaloperations.Ifabuttonispressed

whenlockedafaulttoneplaysasanalertfollowedbyun-

lockinstructionsinthetextfield.

 Tounlockthebuttons,pressthe

buttonfollowedbythe

button.Theunlocktonesplayand„READY“isdisplayed

inthetextfield,acommandcannowbeperformed.

Auto unlocking

 Afterturningtheignitionoff,amessagetotheremotewill

unlockthekeypadbuttonsthenextcommandisperformed.

IfAutoUnlockingisnotdesiredthismessagecanbeturned

offbyanauthorizedDirectedDealer.

• Page Mode

 Options:„POWER SAVE“, „OFF“, „ON“

• Paging is how the Responder LC remote monitors your

3130

system’s messages. „POWER SAVE“ extends battery life by

turningPagingOffafteroneweekiftheremotecontrolis

notusedduringthisperiod.Justpressanybuttontoresume

systemmonitoring.Whensetto„ON“itwakesupeveryfew

secondstolistenforpagesfromthesystem.Whensetton

„OFF“itdoesnotwakeuptoreceiveremotestartoralarm

triggerpages.

Note!

When„OFF“,responsesarestillreceivedwhenacommand

isperformedbutalarmtriggerpageswillnotbereceived.

• Page Alert

 Options:„TONE VIBE“, „TONE“, „VIBE“, „SCREEN ONLY“

 There are several ways for the Responder LC to alert you

when it has received a message from the system. „TONE

VIBE“ will alert by both emitting tones and vibrating the

remote. Select „TONE“ to be alerted by tones that are

uniqueforeachmessage.Select„VIBE“andtheResponder

LC will silently alert you with a gentle vibration, or select

„SCREEN ONLY“whenyoudon’twanttobeinterrupted.

• Remote Start Info (only 5606V)

 Options:„RUNTIME“, „TEMP“, „CLOCK“

 Thetextfieldcanbesettodisplaytheinformationyoupre-

fer during remote start. „RUNTIME“:RemoteStartRuntime,

„TEMP“:vehicleinteriorTemperature,orthe„CLOCK“ will

bedisplayedinthetextfieldwhileRemoteStartison.

• Runtime Alert (only 5606V)

 Options:„ON“, „OFF“

 The main unit will send a page to alert you when the

runtime is about to expire. When set to „ON“, an alert is

generated when the Remote Start Time-out message is

received. When „OFF“, no alert output is emitted for the

message.

• Car 2

 Options:„OFF“, „ON“,„HOME“

 Thisremotecancontroltwosystemsindependently.When

set to „OFF“,theCar2selectoptionisnotavailable.When

set to „ON“theremotecanbesettocontroltwosystems.

The„HOME“optionisforpairingtoahomesecuritysystem.

• Screen Color

 Options: „OFF“, „WHITE“, „LT GRN“, „VIOLET“, „AQUA“,

„RED“, „GREEN“, „BLUE“

 Thestatusscreenbacklightingcanbe„OFF“,orwillilluminate

with a selected color during output when set to one of the

optioncolors.

• Temp Unit

 Options:„F“, „C“

 Temperaturecanbedisplayedinyourchoiceoftemperature

scales,Fahrenheit or Celsius.

3332

• Button Beep

 Options:„ON“, „OFF“

 Whensetto„ON“,theremotewillemitabeepasconfirmation

ofabuttonpress.Whensetto„OFF“,beepsarenotemitted

forbuttonpresses.

• System Type

 Options:„SEC“, „RKE“

 Selectsthetypeofsystem,namely;SecurityorRemote Key-

less Entrytowhichtheremotehasbeenpaired,andadjusts

thetextandmainmenuaccordingly.Thishasbeenpre-setby

thefactoryforyoursystem.

• Clock Set

 Options:„HOUR“, „MIN“

• Review

 Displaysfirmwareversion

• Exit

 Exitsandreturnstothemainmenu

Sensor Adjust

 Ifyoufeelyoursecuritysystemshocksensoristoosensitive

ornotsensitiveenough,itishighlyrecommendedthatyou

contact your authorized Directed dealer/professional and

have the sensor adjusted for optimized security detection

performance.

Pair Remote

 Remote Pair is a process where the ResponderLCandthe

systeminthevehiclelearneachothersencryptedidentifica-

tion, securing their communication from intruders. Please

notethatyourremotecontrolscomepre-programmedfrom

thefactory.

Prepare the vehicle system to be Paired with a new remote

• Openatleastoneofthevehicle’sdoors.

• TurnthekeytotheOnposition.

• WithinfivesecondspressandreleaseonetimetheControl

buttonontheControlCenter.

• Withinfiveseconds,pressandholdtheControlbutton.The

statusLEDwillflashonetimeandthesirenwillchirponceto

confirmthesystemisreadyforremotepairing.

• ReleasetheControlbuttonandproceedbelow.

Note!

If pairing does not result within 60 seconds, the system

willexitandthesirenwillchirp.

Prepare the new remote to be Paired with the system

• MakesuretheremotecontrolissetforthedesiredCar1or

Car2operation.

3534

• PerformthestepsunderAccess menu items section to access

thePairRemotemode.

• Whentheremotebeepsthreetimesand„PAIR“isdisplayed

theremoteisreadytopair.

• Pressthe

button.

• Waitseveralsecondsforfeedbackastheremotegenerates

a security encryption and sends it to the Control Center.

IfPairissuccessful the siren sounds and the remote emits

severaltones.ThescreendisplaysifthePairingissuccessful

orfailed with corresponding text. If pairing failed, repeat

step4.

Demo mode

 DemoModeplaysapre-selectedgroupofanimationsasa

demonstration tool to show friends or family. Running

Demomodeshortensthebatterylifeovertimeifusedex-

cessively

• „SINGLE SILENT“: The remote will display a selection of

icons on the status screen without

 beepsandtonesthenstop.

• „SINGLE SOUND“: The remote will display a selection of

 icons on the status screen with beeps

 andtonesthenstop.

Power Off

 Whenanextendedperiodofnon-operationisanticipated,

turningthepoweroffwillpreservethebatterycharge.Press

the

buttonwhile„POWER OFF“isdisplayed.Thestatus

screeniconsclearasthepowerofftonesplay,theremoteis

turned off.

 To turn the remote on, Press and hold the

button for

threeseconds,thestatusscreeniconsrefreshasthepower

on tones play. The remote also turns itself on and begins

chargingwhenthebatterychargerisconnected.

Exit

 To return tonormaloperation, press the

buttonwhile

EXITisdisplayed.

3736

1-way Companion Remote Control

Button Direct Access

x1 LEVEL 1

x2 LEVEL 2

x3 LEVEL 3

x4 LEVEL 4

Arm/Lock(Panic) SilentArm SensorBypass SensorSilentArm FullSilentArm

Disarm/Unlock SilentDisarm RemoteValet CarFinder

RemoteStart(only5606V)

RuntimeReset

(only5606V)

TimerStart

(nur5606V)

SmartStart

(nur5606V)

Defogger

(nur5606V)

Aux/Trunk AUX1 AUX2 AUX3 AUX4

NotUsed UsedtoaccessfunctionlevelsforAdvancedCommands

Using the 1 way companion remote

The companion 1 way remote commands the system fea-

turesasshownintheprevioustable,butwithoutthemes-

sagedisplayoftheResponderLCremote.Sirenchirpsand

parkinglightflashesareusedtoindicatethatacommand

has been received and activated as described in theBasic

and Advanced command sections.

Accessing Commands

Similar to the Responder LC remote, Basic commands are

performed when a command button is pressed directly.

ToperformAdvancedCommandspressthe

buttonone

3938

to four times to access function

x4inthetableforexample

impliespressing

fourtimes.TheLEDflashesingroupsfora

fewsecondstoindicatethelevel.Pressthedesiredcommand

buttonwhiletheLEDisflashingtoperformthecommand.

Button Auto Lock

WhenOn,theremotecontrolbuttonslockifmorethan20

secondslapsesbetweenbuttonpresses.Ifabuttonispressed

whenlocked,afaulttoneisemitted.Tounlockthebuttons;

pressthe

buttonfollowedbythe

button,thebuttons

unlockandtonesplaytoconfirm.

Car Select

Car2mustfirstbeturnedOn(SeeRemoteFeaturesmenu

under “Programming” on page 44 to turn on). Press and

hold the

buttonfor 3seconds.The remoteflashesthe

LEDandbeepsonceortwicetoindicatetheselectedCaris1

or2,releasethebuttonforCarSelectorcontinuetohold

for programming. Release the

button, then press and

release while the LED and beeps continue to perform Car

Select.Oncethecarisselectedacommandcanbeperformed

bypressingoneofthecommandbuttons.

Programming

Toenter: Press andholdthe

buttonfor eight seconds,

theremoteemitsonelongbeepandturnstheLEDon,the

programmingmainmenuhasbeenaccessed(seemenulist-

ingsbelow).Toexit:Pressandreleasethe

buttononce,

thenpressandholdthe

buttonagain.Oneshortandone

longbeepisemittedforeachstepback,theLEDturnsoff

whenprogrammingisexited.

1. Sensor Adjust

 Toavoidunintendedalarmtriggers,itisrecommencedthatan

authorizedDirecteddealerperformallsensoradjustments.

2. Remote Features menu

 Afterenteringtheprogrammingmode:Pressandholdthe

button,twoLEDflashesandbeepsindicatetheremote

featuresmenuisaccessedandcanbeset.Pressbuttonsindi-

catedbelow,1beepandflashturnsthefeatureon,2beeps

and flashes turns the feature off.

• Autolockfeature:Press to turn on/off.

• RemoteBeeps:Press

to turn on/off.

• Car2feature:Press to turn on/off.

 Tosaveandexittheremotefeatureprogramming,pressthe

buttononceandthenpress/hold,thetransmitLEDshuts

offconfirmingexit.

3. Remote Learning

 Preparethethevehiclesystemtobepairedwithanewremote:

• Openatleastoneofthevehicle’sdoors

• Turnthekeytotheonposition

• Withinfivesecondspressandrelease1timethecontrolbut-

ton on the control center.

• Withinfivesecondspressandholdthecontrolbutton.the

statusLEDwillflashonetimeandthesirenwillchirponceto

confirmthesystemisreadyforremotepairing.

• Releasethecontrolbuttonandproceedbelow.

Viper 7756V Owner's manual

Related papers

Other documents