Palsonic TFTV700HL Owner's manual

Category
LCD TVs
Type
Owner's manual
1
Table Of Contents
Important Safety Instructions.......................................................................................................... 2
View of Unit........................................................................................................................................... 4
Front Panel......................................................................................................................................... 4
Rear Panel.......................................................................................................................................... 5
Remote Control.................................................................................................................................... 6
Remote Control Drawing.................................................................................................................. 6
Preparation of Remote Control........................................................................................................ 8
Using of Remote control................................................................................................................... 8
System Connections.......................................................................................................................... 9
Connecting to the Power Supply..................................................................................................... 9
Connecting a USB Device for Upgrade......................................................................................... 9
Connecting to an External HDMI Signal Source........................................................................ 10
Connecting External Equipment to COMPONENT IN jacks..................................................... 10
Connecting External Equipment to MINI AV jack........................................................................ 11
Connecting to Coaxial Digital Output............................................................................................ 11
Connecting to a PC......................................................................................................................... 12
Connecting to Earphones.............................................................................................................. 12
Connecting to TV-Signal Input....................................................................................................... 13
Basic Operation................................................................................................................................. 14
Turning the TV On and Off............................................................................................................. 14
Source selecting.............................................................................................................................. 14
Channel Selection........................................................................................................................... 14
The First Time Installation.............................................................................................................. 14
TV Operation and System Setup................................................................................................... 15
Picture Setting................................................................................................................................. 15
Sound Setting.................................................................................................................................. 16
Channel............................................................................................................................................. 17
Feature.............................................................................................................................................. 19
Setup................................................................................................................................................. 22
PVR Function..................................................................................................................................... 23
Time Shift Function......................................................................................................................... 23
Recording program......................................................................................................................... 23
Playing recorded program.............................................................................................................. 24
Schedule Recording........................................................................................................................ 24
EPG Function..................................................................................................................................... 25
TELETEXT Function......................................................................................................................... 26
NICAM Function................................................................................................................................ 27
Media Playback.................................................................................................................................. 28
Media Playback............................................................................................................................... 28
Function Buttons.............................................................................................................................. 29
Troubleshooting................................................................................................................................ 30
Specifications.................................................................................................................................... 31
The images in this manual are for reference only and may differ from your model.
2
Important Safety Instructions
Thank you for choosing our product. Please read this manual carefully and observe all safety
and operating instructions. Store the manual in a safe place for later reference.
Caution
1. The product contains a low-power device. In order to ensure the safety of the laser device,
do not remove any cover and attempt to repair the unit. If any service is needed, please
contact the distributor or its authorised service center.
2. To reduce the risk of electric shock, do not remove the cover (back). No user-serviceable
parts inside. Refer servicing to qualified service personnel. Unplug the product from the
power source before servicing or when it is unused for a long period of time.
3. The manufacturer will not be held responsible for the damage caused by any substitutions
and modification of the product without authorization from the manufacturer’s or authorised
service agent.
WARNING
The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the apparatus.
The information symbol in the documentation indicates useful information and
tips for using and maintaining the device.
The information symbol in the documentation indicates cautions for operators to
avoid potential damages. Please note and remember.
IMPORTANT INFORMATION
If a television is not positioned in a sufficiently stable location,it can be potentially hazardous
due to falling. Many injuries, particularly to children, can be avoided by taking simple
precautions such as:
1. Using cabinets or stands recommended by the manufacturer of the television.
2. Only using furniture that can safely support the television.
3. Ensuring the television is not overhanging the edge of the supporting furniture.
4. Not placing the television on tall furniture (for example, cupboards or bookcases) without
anchoring both the furniture and the television to a suitable support.
5. Not standing the televisions on cloth or other materials placed between the television and
supporting furniture.
6. Educating children about the dangers of climbing on furniture to reach the television or its
controls.
This symbol indicates that dangerous voltage instituting a risk of electric shock
is present within this unit.
This symbol indicates that there are important operation and maintenance
instructions in the literature accompanyin g the appliance.
3
Important Safety Instructions
NOTES:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Maintain well ventilated conditions around the
product. Do not put product on a bed, sofa or anything that blocks ventilation. Install
according to the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce heat.
9. Read, heed and follow all instructions to ensure correct and safe installation and
interconnection of the apparatus;
10. The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the apparatus.
11. The mains socket-outlet shall be installed near the apparatus and the mains plug shall
remain readily operable.
12. Protect the power cord from being walked on or pinched particularly at plugs, power
sockets, and the point where they exit from the apparatus.
13. Only use attachments/accessories specified by the manufacturer.
14. Use only with the stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus.
15. Unplug the apparatus during lightning storms or when unused for long periods of time.
16. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
17. The apparatus s hall be connected to a mains socket outlet with a protective earthing
connection.
Do not touch the color LED screen directly by hand.
4
View of Unit
Front Panel
1. Color TFT screen
Presents high resolution picture.
2. Remote Sensor
Remote sensor window for the remote control.
3.
Power Indicator
In active mode, it is green; in standby mode, it turns red.
4.
POWER button
Press to switch on or off the device (enter or exit the standby mode).
5.
VOL ▲▼ buttons
Press to decrease or increase the volume.
When in setup menu, this button also serves the ◄► direction button.
6.
CH ▲▼ buttons
Press to page up or down through programs in DTV or ATV mode.
When in setup menu, this button also serves the ▲▼ direction button.
7.
MENU button
Press to enter or exit system setup menu.
8.
INPUT button
Press to display a menu of all of the available input sources.
When in setup menu, this button also serves the OK button.
5
View of Unit
Rear Panel
1.
POWER Jack
Connect to the power adapter for power
supply.
2. HDMI1/HDMI2/HDMI3 Input Jacks
Connecting for HDMI signal.
3.
COMPONENT IN Jacks
Connecting for the Y/P
b
/P
r
input in
YPBPR mode.
4. RF Input Jack
Connected to external antenna to
receive the ATV/DTV program in
ATV/DTV mode.
5. Headphone Jack
When headphone is inserted, the
loudspeaker is switched off.
6
.
MINI AV Jack
Connecting for AV signal input in AV
mode.
7
.
COAXIAL Jack
Output the coaxial digital audio signal.
8
.
PC IN Jacks
Connecting for VGA audio s ignal input.
9
. VGA Jack
Connected to the VGA output jack on a
personal computer.
1
0.
USB Port
Connect the USB device.
6
Remote Control
Remote Control Drawing
1. POWER button
Press to enter or exit standby mode.
2. SOUND button
Press to select the sound mode: choose
from Standard, Movie, Music, Speech o
r
User.
3. PICTURE button
Press repeatedly to select the picture
mode: Standard, Mild, Use
r
o
r
Dynamic.
4. CH.LIST button
Press to display the channel list.
5. SUBTITLE button
In DTV/DVD m ode, press to select
alternate subtitle languages during
view/playback o
f
a DTV program.
6. TV.RADIO button
Press to select DTV program playback
o
r
Radio program playback in DTV
mode.
7. Direction buttons (▲▼◄►)
In the setup menu, press the ▲▼ button
to select a desired item and press the
◄► button to adjust o
r
set.
8. OK button
Press to confirm selection in the setup
menu.
9. MENU button
Press to enter setup menu or return to
the previous menu.
10. 0~9 Number buttons
Press to select numbers such as TV
channel.
11. REC. button
In DTV mode, press to enter the
recorder.
12. VOL+/- button
Press to increase or decrease the
volume.
13.
Play/Pause button
Press to start or pause the playback.
When in DTV recorder, press to start or
pause the recording.
14. Red Coloured button
In Channel Manager, use the red button
to delete a program.
In teletext mode, it is the teletext color
button.
Other defined functions on the OSD
menu.
15. Green Coloured button
In Channel Manager, use the green
button to lock a program.
In teletext mode, it is the teletext color
button.
Other defined functions on the OSD
menu.
7
Remote Control
16. TV/TXT
Press to change the mode between TV
and Teletext
17. CANCEL button
Press this button to disable teletext
display and press again to resume.
18. (INDEX)/(HOLD) buttons
Press to search backward or forward in
media player.
In teletext mode, press INDEX button to
select the index page.
In teletext mode, press HOLD button to
hold the current page and press again to
resume.
19. MUTE button
Press to turn on or off the speaker
output.
20. ASPECT button
Press to shift the aspect radio of the
screen.
21. SLEEP button
Press the button repeatedly to select the
desired time to sleep o
r
select Of
f
to
close the function.
22. EPG button
Press to display the Program Guide
menu in DTV mode.
23. FAV button
Press to display the favorite list.
24. INPUT button
Press to enter the source selecting menu,
press the ▲▼ direction buttons o
r
press
the INPUT button repeatedly to select
desired source and press the OK button
to ente
r
the selected source.
25. EXIT button
Press to exit all the OSD on the screen.
26.
button
In ATV or DTV mode, press to return t o
the channel previously viewed.
27. DISPLAY button
Press to display the reference
information o
f
the current mode.
28. REC LIST button
Press to display the Record List.
29. CH▲▼ button
In ATV or DTV mode, press to select
analog program o
r
digital program.
30. STOP button
Press to stop playback in media mode.
When in DTV recorder, press to stop the
recording.
31. Blue Coloured button
In Channel Manager, use the blue button
to swap programs.
In teletext mode, it is the teletext color
button.
Other defined functions on the OSD
menu.
32. Yellow Coloured button
In Channel Manager, use the yellow
button to skip a program.
In teletext mode, it is the teletext color
button.
Other defined functions on the OSD
menu.
33. NICAM/A2 button
Press to select audio l anguage in DTV
mode. Press to select sound track in
othe
r
modes except DTV mode.
34. Reveal button
Press this button to display or remove
concealed information on the screen.
35. (SIZE)/(SUBPAGE) buttons
Press to return to the previous file or skip
to the next one in media player.
In teletext mode, press SIZE button first
time to double the size o
f
teletext letters
in the uppe
hal
f
o
f
the screen, second to
double the size o
f
teletext letters in the
lowe
r
hal
f
o
f
the screen and third to
resume normal status.
In teletext mode, press SUBPAGE
button to look at a sub-page.
8
Remote Control
Preparation of Remote Control
1. Softly push the back cover to open the
battery compartment.
2. Insert two batteries (1.5V, size AAA),
please make sure the polarity matches
the marks inside the compartment.
3. Softly press the back cover to close it.
Under normal use the battery
will last for six months.
Take out battery when the
remote is not in use for a
long time.
Using of Remote control
Point the remote control unit from no more
than about 7 meters from the remote control
sensor and within about 60 degrees of the
front of the unit.
The operating distance may vary
depending on the brightness in the room.
Do not point bright lights
directly at the remote control
sensor.
Do not place objects
between the remote control
unit and the remote control
sensor.
Do not use this remote
control unit while
simultaneously operating the
remote control unit of any
other equipment.
9
System Connections
Do not connect the power cord until all other connections have been made.
Ensure that you observe the color code when connecting audio and video
cables.
Connecting to the Power Supply
Power is supplied through the appropriate power adapter, one end is connected to the
POWER jack on the rear panel of the unit, the other end to the AC 100~240V wall outlet.
NOTES
Please use the power adapter specified by the manufacture.
Connecting a USB Device
This unit is designed with a USB port so that you
can connect your USB device for media play,
record or software upgrade. See the figure as
shown right:
Make sure that the desired file for media play or software upgrade is stored in the
USB device before connection.
10
System Connections
Connecting to an External HDMI Signal Source
1. Connect an HDMI signal source to one
of the HDMI jacks on the rear panel of
the unit.
2. After connection, turn on the power of
the unit and the HDMI signal source.
3. Press INPUT then direction buttons to
select HDMI 1, HDMI 2 or HDMI3
mode, and then press the OK button to
confirm.
HDMI provides both audio and video signals and typically provides superior
image quality to AV and YPBPR.
Connecting External Equipment to COMPONENT IN jacks
1. Use the AV cables to connect
the external AV s ignal source to
the MINI AV input jacks on the
rear panel of the unit.
2. Use a component cable (not
supplied) to connect an external
AV signal source to the Y/PB
/PR (Component) input jacks on
the rear panel of the unit.
NOTE: Match the jack colors
(Y= green, PB= blue, and PR=
red).
3. After connection, turn on the
power of the unit and the
external AV signal source.
4. Press INPUT then direction buttons to select YPBPR mode, and then press the OK button
to confirm.
11
System Connections
Connecting External Equipment to MINI AV jack
Use the AV cables to connect the external AV signal
source to the AV input jacks on the rear panel of t he
unit.
After connection, turn on the power of the unit and the
external AV signal source. Press INPUT then direction
buttons to select AV mode, and then press the OK
button to confirm.
Connectin
g
to Coaxial Di
g
ital Output
This unit is designed with a coaxial digital audio jack,
can be connected to the digital amplifier, see the figure
below.
This feature is available only for amplifiers equipped with coaxial digital audio
input connectors.
12
System Connections
Connecting to a PC
The unit can be connected to a PC via the VGA cable and PC audio cable.
1. Connect one end of the VGA cable to
the VGA jack on the jack panel of the
unit and the other end to the PC VGA
output.
2. Connect one end of the audio cables
to the PC IN jack on the jack panel of
the unit and the other end to the PC
audio output jack.
3. Set the PC video resolution to match
that of the television (Native 1366 x
768@60Hz).
4. After connection, turn on the power o
f
the unit and the PC.
5. Press INPUT then direction buttons to
select PC mode, and then press the
OK button to confirm.
Connectin
g
to Earphones
Connect earphones (headphones) to the earphone jack on
the rear panel of the unit for listening to the audio output in
seclusion. The internal speakers output will turn off
automatically after the earphones have been connected.
Excessively loud volume could damage your hearing. Turn down the volume
before you connect the earphones and then raise the volume to a comfortable
level.
13
System Connections
Connecting to TV-Signal Input
Connect the TV signal cable (the
antenna cable, for example) to the RF
Jack on the back of the unit so that you
can receive television programs.
1. Connect TV signal input source from the aerial to the RF jack on the rear panel of the unit.
2. After connection, turn on the power of the unit.
3. Then press the INPUT button and the direction buttons to select DTV or ATV mode, press
the OK button to confirm and conduct program selection.
14
Basic Operation
Turning the TV On and Off
Connect the power adapter to wall AC Outlet. A front mounted indicator light will be
illuminated red indicating the TV has power.
Press the POWER button on the remote control or the TV set. The TV’s indicator light will
be illuminated blue indicating the TV is turned ON.
Press the POWER button again to turn the TV off. A front mounted indicator light will be
illuminated red indicating the TV is off.
Source selectin
g
The unit incorporates multiple input sources which can be selected via the
INPUT button on the television or remote. Press the INPUT button to enter
Input menu, as shown right.
Use the ▲▼ direction buttons and the OK button
On the input menu, press the ▲▼ direction button t o select the desired
input source. After several seconds, the TV will enter the selected
source.
Or after you selected the desired source press the OK button to enter the
selected source immediately.
Use the INPUT button and the OK button
On the input menu, press the INPUT button repeatedly to select the
desired input source. After several seconds, the TV will enter the selected source.
Or after you selected the desired source press the OK button to enter the selected source
immediately.
Channel Selection
1.
Using CH▲▼ button
2.
Use the CH.LIST button to display the channel list and press the ▲▼ button to
select channel.
3.
You have also quick access to the different TV channels by using the numeric
buttons.
4.
Using button on the remote control to view the last channel you were watching.
The First Time Installation
The first time you turn on the TV or after you reset all the settings to their original status,
the Auto Installation will start. Follow the prompts on the screen to set the Country,
Language, Auto Power Off and the Auto Search, then press OK button and the channel
tuning starts immediately.
All found TV programs will be saved into the channel list. You can load at the TV channel
list by press the CH.LIST button.
15
TV Operation and System Setup
Press the MENU button to display the setup menu. It includes different categories, such as
Picture, Sound, Channel, Feature and Setup.
You can change the category using the ▲▼ buttons and press OK button or the button
to enter it.
Using the ▲▼ buttons and press OK or button to enter the submenu of each option in
the category. Press the MENU button to exit the submenu and return to the previous menu.
To leave t he system settings, press the EXIT button.
Picture Setting
PICTURE setting includes Picture Mod
e
Brightness, Contrast, Sharpness,
Colour, Tint, Colour Temperature and
Aspect Ratio.
Picture Mode
Press the ▲▼ buttons to select Picture Mode and then press OK or button, the available
picture modes will be listed on the screen.
With the ▲▼ buttons you can select Dynamic, Standard, Mild or User.
Brightness/ Contrast/ Sharpness/ Colour/ Tint
Press the ▲▼ button to select Brightness/ Contrast/ Sharpness/ Colour/ Tint and press OK
or button to enter the adjusting bar, then press the ◄► button to adjust the level.
The Picture Mode will change to User automatically when you are setting the level of the
Brightness/ Contrast/ Sharpness/ Colour/ Tint.
Color Temperature
Press the ▲▼ buttons to select Color Temperature and then press OK or , the available
Colour Temperature will be listed on the screen.
With the ▲▼buttons you can select Standard, Cool or Warm.
Aspect Ratio
Press the ▲▼ buttons to select Aspect Ratio, then press OK or to enter it. With the
▲▼buttons you can select your desired aspect ratio.
Note: In different input source, the available aspect ratios may vary.
16
TV Operation and System Setup
Noise Reduction
Press the ▲▼ buttons to select Noise Reduction, then press OK or to enter it. With the
▲▼ buttons you can select Off, Low, Middle or High.
Sound Settin
g
The sound settings include the options
for Sound Mode, Bass, Treble, Balance,
Surround, AVL and SPDIF.
Sound Mode
Press the ▲▼ buttons to select Sound Mode and then press OK or , the available Sound
Modes will be listed on the screen. With the ▲▼ buttons you can select Standard, Movie,
Music, Speech or User.
If you select User, you can set the levels of the Bass and Treble as you desired.
Bass & Treble
Press the ▲▼ buttons to select Bass/Treble and then press OK or to enter the adjusting
bar.
With the ◄► buttons you can adjust t he level of it.
Balance
Press the ▲▼ buttons to select Balance and then press OK or to enter the adjusting bar.
With the ◄► buttons you can adjust the level of balance.
Surround
Press the ▲▼ buttons to select Surround and then press OK or to list the available settings.
With the ▲▼ buttons you can select Off or On.
AVL
Some times different TV stations volume level may be different from each other; this function
will normalize audio level from all channels.
Press the ▲▼ buttons to select AVL and then press OK or .Usethe▲▼ buttons to select
On to activate this function or Off to deactivate this function.
SPDIF
Press the ▲▼ buttons to select SPDIF and press the OK or to list the available settings.
With the ▲▼ buttons you can select Off, PCM or Auto.
17
TV Operation and System Setup
Channel
CHANNEL includes Channel
Management, Favorite Management,
Country, Auto Search, DTV Manual
Search and ATV Manual Search.
NOTE:
The Channel category is only active in
DTV and ATV mode.
When in DTV mode, the ATV Manual
Search is not available; and when in
ATV mode, the DTV Manual Search is
not available.
Channel Management
The option “Channel Management
includes Delete, Lock, Skip and Swap.
Deleteaprogram:
1.
With the ▲▼ buttons you can
choose a channel, which shall
be deleted.
2. Press the red coloured button
to delete it.
Lock a program
1.
With the ▲▼ buttons you can choose a channel, which shall be locked.
2. Press the green coloured button to lock it.
Swap programs: (only for ATV programs)
1.
With the ▲▼ button you can select a channel, which shall be moved.
2.
Press the yellow coloured button.
3.
Move the channel with the ▲▼ button on the position which you like.
4.
Save the moving by pressing the MENU button.
Skip a program:
1.
With the ▲▼ buttons you can select a channel, which shall be moved.
2.
Press the blue coloured button.
3.
Press the blue coloured button again to cancel.
NOTE: A skipped program is skipped when using the CH / buttons to browse the
programs but can be watched by selecting in the channel list or
us
ing the number buttons.
18
TV Operation and System Setup
Favorite Management
In the Favorite Manager, there are four
groups of your favorite programs: Fav1,
Fav2, Fav3 and Fav4.
With the ▲▼ buttons select a program
and press the different coloured button
to set it in different group.
Press red coloured button to set it in
group Fav1.
Press green coloured button to set it in
group Fav2.
Press yellow coloured button to set it in
group Fav3.
Press blue coloured button to set it in group Fav4.
Country
Select this item and press the OK or button to enter the country list. With the ▲▼ buttons
you can select your desired country.
Auto Search
Select this item and press the OK or button to enter the submenu. Press the ▲▼buttons to
select the different search type: All, DTV or ATV. Press OK to start t he auto search. A new
window appears on the screen, where the status of the searching is documented. The values
of the found TV broadcast programs of ATV, DTV and Radio are listed.
After finishing of the searching, all found TV programs will be saved into the channel list. You
can load at the TV channel list by press the CH.LIST button.
Press the EXIT button to exit.
NOTE: Please allow a few minutes for this feature to scan the entire range of available
programs.
DTV Manual Search
1. Press the ▲▼ buttons to select
DTV Manual Search and press the
OK or button to enter the
submenu. The screen will display as
shown on the right:
2.
In the submenu, you can define on
which channel shall be runs the
search. You can also set the
frequency and bandwidth.
3.
Starts the searching by the press the Start button in the submenu.
4.
To leave the DTV Manual tuning, press the EXIT or MENU button.
19
TV Operation and System Setup
ATV Manual Tuning
1.
Press the ▲▼ buttons to select
ATV Manual Search and press the
OK or button to enter the
submenu. The screen will display as
shown on the right:
2.
Press the ▲▼ buttons to select
desired item, press the OK or
button to enter the submenu to set.
3.
To leave the ATV Manual Search,
press the EXIT or MENU button.
Feature
The Feature settings include the options
for Lock, Language, Clock, Sleep Timer,
Auto Power Off, Hearing Impaired and
PVR/Timeshift.
Lock
Before you can change the settings, you have to insert the preset password to enter the
menu. The default is 0000.
The lock settings include the options for
Lock Enable, Parental Guidance,
Change Pin code and Hotel Mode.
Lock Enable
Press the OK or button to
enter the submenu. With the
▲▼ buttons to select On or Off.
Parental Guidance
With this option you can define
the level of the parental control.
Change Pin code
With this option you can change the preset password. Please insert the new password
and confirm it again.
Hotel Mode
This television is designed with hotel mode. With this option you can set it.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33

Palsonic TFTV700HL Owner's manual

Category
LCD TVs
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI