Supermicro SuperServer 5017P-TLN4TF Quick Reference Manual

Brand: Supermicro

Model: SuperServer 5017P-TLN4TF

Type: Quick Reference Manual

http://www.supermicro.com MNL-1368-QRG

Board Layout

SuperServer 5017P-TLN4F/TF Quick Reference Guide

Power Button

Reset Button

Power LED

Device Activity LED

LAN1 LED & LAN2 LED

Information LED

Description

No.

Rear View

Beep Codes

Front view & InterfaceMEMORY

Caution

1234

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning

before connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING:

To reduce risk of electric shock/damage to equipment,

disconnect power from server by disconnecting all power

cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap

CAUTION:

Always be sure all power supplies for this system have

the same power output. If mixed power supplies are

installed, the system will not operate.

For more information go to :

http://www.supermicro.com/support



Description

No.

PCI-E x16 Gen 3 Slot

CPU

DIMMA1

DIMMB1

I-SATA5, I-SATA4, I-SATA3, I-SATA2 (Black connector: SATA2)

JSD1 = DOM (Disk on Module) Power Connector

I-SATA0, I-SATA1 (White connector: SATA3)

JF1 = Front panel control header

JBT1 = CMOS Clear

Description

No.

110 257 6

JWD1

UID

VGA

JWP1:WRITE PROTECT

PWR I2C

U60

I-SATA0I-SATA1

JIPMB1

T-SGPIO2T-SGPIO1

JSD1

I-SATA5

I-SATA2

I-SATA4

I-SATA3

JCOM2

J20USB1

SP1

LED2

LED1

LED3

U21

U10

U22

JDIMM1

JDIMM2

FAN2FAN3

FAN1

FAN4

U26

JPW1

JPI2C1

JPK1

JTPM1

JLAN1JLAN2

MH7

MH6

MH2

MH4

JD1

JF1

JP1

JPUSB1

JPB1

JWP1

JL1 JOH1

MH4

U57

X9SPV-F

JTPM1:TPM/PORT80

DOM POWER

P1-DIMMB1

USB8/9

JSD1:SATA

COM2

USB6/7

LAN2/4

LAN1/3

P1-DIMMA1

COM1

USB4/5

KB/MOUSE

CPU1

JVGA1

JCOM1

Informational LED

Status Description

Blinking red (1Hz)

Fan failure, check for an inoperative fan.

Solid blue

Local UID has been activated.

Use this function to locate

Continuously

on and red

An overheat condition has occured.

(This may be caused by cable congestion.)

Blinking red

(0.25Hz)

Power failure, check for a non-operational

power supply.

Blinking blue

(300 m/s)

Remote UID is on. Use this function to identify

the server from a remote location.

BIOS Beep Codes

Video configuration error

Memory

No memory detected

Error Message

Beep Code/LED Description

1 long + two short beeps

Video

1 repetitive long beep

1 continuouse beep

w/Overheat LED

Overheat

System overheat detected

1 continuouse beep

w/Fan Fail LED blinking

Fan

Fan failure detected

8 short beeps

Display

Display memory

read/write error

ÌMNL-1368-QRG4Î

4 3

Expansion Slot

VGA Port

Gb LAN 3/4 (5017P-TLN4F only)

Gb LAN 1/2

USB Port 8/9

USB Port 4/5

COM Port 1

PS/2 Keyboard/Mouse

Dedicated IPMI LAN Port

Power Supply

Insert the SO DIMM module

straight down.

To Remove:

Use your thumbs to gently

push the side clips near both

ends away from the module.

This should release it from

the slot. Pull the SO DIMM

module upwards.

The SO DIMM Socket

Position the SO DIMM

module's bottom key so it

aligns with the receptive

point on the slot. Take

note of the module's side

notches and the locking

clips on the socket.

Press down until the module

locks into place. The side

clips will automatically secure

the SO DIMM module, locking

it into place.

Align

Hard Drive Configuration Options

Two 2.5" HDDs

In a Double Bracket, Four HDD's Total,

No Expansion Card

Two 2.5" Hard Drives

and One Full-Height,

Half-Length Expansion Card

One 3.5” Hard Drive

and Low Profile

Expansion Card

Two 3.5" Hard Drives

and No Expansion Card

Note: Compatibility of add-on cards dependent on component height, etc.

Supermicro SuperServer 5017P-TLN4TF Quick Reference Manual

Supermicro SuperServer 5017P-TLN4TF Quick Reference Manual

Supermicro SuperServer 5017P-TLN4TF Quick Reference Manual

Related papers

Other documents