Extron TLP Pro 1022T User manual

Extron
Brand
Extron
Model
TLP Pro 1022T
Type
User manual

Extron TLP Pro 1022T is a 10-inch tabletop capacitive touchscreen with 1024x600 resolution and 18-bit color depth. It offers flexible mounting options and fully customizable interfaces. You can use it to control AV systems, lighting, and other devices in your home or office. The TLP Pro 1022T also has a built-in motion sensor that can be used to wake the device from sleep mode when you approach it.

Extron TLP Pro 1022T is a 10-inch tabletop capacitive touchscreen with 1024x600 resolution and 18-bit color depth. It offers flexible mounting options and fully customizable interfaces. You can use it to control AV systems, lighting, and other devices in your home or office. The TLP Pro 1022T also has a built-in motion sensor that can be used to wake the device from sleep mode when you approach it.

1
Product Category
IMPORTANT:
Go to www.extron.com for the
complete user guide and installation
instructions befor
e connecting the
pr
oduct to the power sou
rce.
www.extron.com
TLP Pro 1022T • Setup Guide
Overview
The TLP Pro 1022T is a 10-inch tabletop capacitive touchscreen with 1024x600 resolution and 18-bit color depth. It offers exible
mounting options and fully customizable interfaces. This guide provides instructions for experienced installers to mount and
install a TLPPro 1022T touchpanel. For complete instructions, see the TLPPro 1022 Series User Guide, at www.extron.com.
Setup Checklist
Get Ready
Download and install the latest version of the following software:
GUI Designer — for designing layouts for Extron TouchLink
®
Pro touchpanels and third party touch interfaces.
Global Configurator
®
Professional or Global Configurator Plus — for setting up and conguring the control processor
and touchpanel.
Toolbelt — provides device discovery, device information, rmware updates, and conguration of network settings,
system utilities, and user management for TouchLink Pro devices.
All three software programs are available from www.extron.com.
Obtain the following network information from your network administrator:
DHCP status (on or off). If DHCP is off, you must also obtain:
IP address Subnet mask Gateway
User name — this can be either admin or user.
Password — by default this is extron (for either admin or user).
Make a note of the touchpanel MAC address.
Mount and Cable All Devices
ATTENTION:
• Do not power on the touchpanels or control processors until you have read the Attention in the “Rear Panel Features”
section of the TLP Pro 1022 Series User Guide or the IPCP Pro User Guide or IPL Pro User Guide.
• Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu la mise en garde dans la section «Rear Panel
Features » du TLP Pro 1022 Series User Guide ou du IPCP Pro User Guide or IPLProUserGuide.
Mount the units. There are several mounting options for TouchLink Pro touchpanels (see Mounting on the following page).
Connect the touchpanel to a Power over Ethernet injector.
Connect the power injector to the LAN and power it on.
Set up the Touchpanels for Network Communication
Connect the PC that you are using for setup, the control processor, and touchpanel to the same Ethernet subnetwork.
Use the Setup Menu (see page 4) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask,
gateway, and related settings for the touchpanel.
Configure the Touchpanels
The GUI Designer Help File, the Global Configurator Help File, and the Toolbelt Help File provide step-by-step instructions and
more detailed information. The Global Configurator Help File includes an introduction to the software and sections on how to start
a project and conguration.
2
TLP Pro 1022T • Setup Guide (Continued)
Mounting
The TLP Pro 1022T comes with a stand that allows it to be placed on
any suitable at surface. See www.extron.com for a range of available
optional mounting kits. The kits must be purchased separately. Follow
the installation instructions provided with the kit.
Removing the Base and Back Covers
To attach cables and to mount the TLP Pro 1022T with the SMA-1 or a
VESA mounting kit, you must remove the base and back covers:
1. Remove the base cover using the provided Extron removal tool.
There is a notch at the back edge of the cover (see gure 1,
2
).
2. When the base cover is removed, a pull tab can be seen (see
gure 2). Use this to remove the back cover.
NOTE: When replacing the covers, attach the back
cover before the base cover.
Kensington
®
Security Lock
For added security, attach a Kensington Security Lock (not provided)
to the metal-reinforced slot on the rear edge of the base (see gure 1,
1
). Follow the instructions that are provided by the manufacturer to
install the lock.
Securing the Touchpanel to a Table
1. Under the table top, mark the location of two mounting holes,
3.07inches (78 mm) apart (see gure 3,
A
).
2. Drill two holes through the table top from underneath.
3. Attach the touchpanel, using two #8 machine screws through the
table top from underneath into the two holes in the base.
SMA-1 Swivel Mount Adapter
The TLP Pro 1022T can be mounted with the optional Extron SMA-1
swivel mount adapter, which allows it to be mounted permanently and
swivel up to 180° in either direction.
1. Remove the base and back covers as described in Removing the
Base and Back Covers, above.
2. Remove the screw holding the locking plate at the bottom of the
base (see gure 3,
B
). This releases the weight, which can be
removed from the top of the base, leaving the mounting hole that
will t over the conduit of the SMA-1.
3. Attach the conduit, insulation disk, and swivel disk and congure
the set screws to allow for the degree of swivel that is required
(see the SMA-1 Swivel Mount Adapter Kit User Guide, available at
www.extron.com).
4. Place the mounting hole in the base over the SMA-1 conduit.
5. Secure the unit with the backing plate and locking nut as
described in the SMA-1 Swivel Mount Adapter Kit User Guide.
VESA Mounting
1. Remove the back cover, as described in Removing the Base and
Back Covers, above.
2. Remove the four screws holding the touchpanel to its base. There
are two screws in each base attachment hinge (see gure 5,
F
).
3. Use a D-type VESA mounting kit with 75 x 75 mm mounting
pattern. Follow the instructions provided with the kit.
11 22
Figure 1. Rear of TLP Pro 1022T Base
Pull Tab
(to Remove
Back Cover)
Figure 2. TLP Pro 1022T with Base Cover Removed
A
B
Figure 3. TLP Pro 1022T Base
3
Product Category
Front Panel Features
BA C
E
D
E
F
Figure 4. TLP Pro 1022T Front Panel
A
Communication LED — shows the conguration and connection status of the touchpanel:
z Unlit during normal operation (the touchpanel is congured and connected to an IP Link Pro control processor).
z Blinks red if the touchpanel has been congured but is not connected to an IP Link Pro control processor.
z Continuously lit red if the touchpanel has not been congured.
The indicator can be toggled between enabled and disabled, using the Setup Menu (see the following page).
B
Status lights — one LED light bar, above the screen, which can be programmed to provide system feedback.
z Light red or green
z Blink or light continuously
z For information about programming this light, see the Global Configurator Help File.
C
Light sensor — monitors ambient light level and adjusts screen brightness.
D
Capacitive touchscreen — 10.1-inch screen with 1024x600 resolution.
E
Speakers — two speakers, located below the screen, one on each side of the panel, provide audible feedback for the user.
F
Motion sensor — detects motion between three to ve feet in front of the touchpanel, and at least 15° from the center axis.
z When no motion has been detected for a user-dened period of time, the touchpanel enters sleep mode.
z When motion is detected by the sensor, the screen display is restored and active.
Rear Panel Features
D
A
B
C
E
F
Figure 5. TLP Pro 1022T Rear Panel
A
LAN/PoE (Power over Ethernet) Connector
B
VESA Mounting Holes (4)
C
Menu Button
D
Reset Button
E
Reset LED
F
Base Attachment Hinges (2)
4
68-2405-53 Rev. A
04 16
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Australia
+61.8.8351.2188
+61.8.8351.2511 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2016 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
TLP Pro 1022T • Setup Guide (Continued)
A
LAN/PoE (Power over Ethernet) Connector — is in the top of the recessed area (see figure 5,
A
on the previous
page). Connect the touchpanel to a PoE power injector (not provided) using a twisted pair cable, terminated with an RJ-45
connector. Connect the power injector to the LAN through a network switch. An Extron IP Link Pro control processor must
also be connected to the same network as the TouchLink Pro touchpanel.
ATTENTION:
• The TLP Pro 1022M is Power over Ethernet (PoE 802.3af, class 3) compliant. Do not power on the touchpanels
or control processors until you have read the Attention in the “Rear Panel Features” section of the TLP Pro 1022
Series User Guide or the IPCP Pro User Guide or IPL Pro User Guide.
• Le TLP Pro 1022M est compatible avec l’alimentation POE via Ethernet (PoE 802.3af, classe 3). Ne branchez pas
les écrans tactiles ou les contrôleurs avant d’avoir lu la mise en garde dans la section «Rear Panel Features » du
TLP Pro 1022 Series User Guide ou du IPCP Pro User Guide or IPLProUserGuide.
NOTE: The TLP Pro 1022T is shipped without a power injector. The power
injector must be purchased separately.
The gure to the right shows the Extron XTP PI 100. Your power injector may look
different.
B
VESA mounting holes (4) — If using VESA mounting, use a D-type VESA mounting
kit with 75 x 75 mm mounting pattern (see VESA Mounting on page 2).
C
Menu button — activates the Setup Menu and calibration screen (see below).
D
Reset button — Pressing the Reset button allows the unit to be reset in any of three different modes. For full information
about the modes, see the TLPPro 1022 Series User Guide.
E
Reset LED — provides feedback about the reset status when the user presses the Reset button.
F
Base attachment hinges (2) — Each hinge secures the touchpanel to the base with two screws.
Reset Modes: a Brief Summary
The TLP Pro 1022T offers the following reset modes:
• Use Factory Firmware:
Press and hold the
Reset button (figure 5,
D
) while applying power to the unit. Use
this mode with Global Congurator or Toolbelt software to replace rmware in the event of
conicts arising from uploading a rmware update.
• Reset All IP Settings:
Press and hold the
Reset button for 6 seconds. After the Reset LED (figure5,
E
) ashes
twice, release and momentarily press the
Reset button. Use this mode to reset all network
settings without affecting user-loaded les.
• Reset to Factory Defaults:
Press and hold the
Reset button for 9 seconds. After the Reset LED ashes three times,
release and momentarily press the
Reset button. Use this mode to return the touchpanel
to factory default settings.
Setup Menu
Press the Menu button (see figure 5,
C
) to open the setup menu.
Select any of the ve available screens (Status, Network, Display,
Audio, and Advanced) by pressing the appropriate button in the
navigation bar at the top of the screen (for more information, see the
TLP Pro 1022 Series User Guide).
Press and hold the
Menu button for at least 3 seconds to open the
calibration screen. Follow the on-screen instructions.
Figure 6. Setup Menu: Status Screen for TLP Pro 1022T
Status
Display Audio Advanced Exit
Network
Network
IP Address:
DHCP:
Host Name:
Off
192.168.254.251
TLP-AB-CD-EF
Display
Resolution:
Project:
Sleep Timer:
1024x600
N/A
5 Minutes
Audio
Master Volume:
Master Mute: Off
99
Advanced
Controller IP: N/A
Project Size: N/A
Info
Model: TLP Pro 1022T
Part Number: 60-1601-02
Firmware
Version:
2.01.0000.b003
PoE: Active
Bootloader
Version:
1.03
100-240V
~
50-60Hz
0.4A MAX
XTP
PWR
XTP PWR
To network switchTo touchpanel
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Extron TLP Pro 1022T User manual

Extron
Brand
Extron
Model
TLP Pro 1022T
Type
User manual

Extron TLP Pro 1022T is a 10-inch tabletop capacitive touchscreen with 1024x600 resolution and 18-bit color depth. It offers flexible mounting options and fully customizable interfaces. You can use it to control AV systems, lighting, and other devices in your home or office. The TLP Pro 1022T also has a built-in motion sensor that can be used to wake the device from sleep mode when you approach it.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents