Endura Ultimate Slide Bolt Astragal Operating instructions

Endura
Brand
Endura
Model
Ultimate Slide Bolt Astragal
Type
Operating instructions

This manual is also suitable for

Endura Ultimate Slide Bolt Astragal

The Endura Ultimate Slide Bolt Astragal is a versatile and easy-to-install security device that can be used on inswing doors. It features a high-quality construction and a user-friendly design, making it a great choice for both residential and commercial applications.

The astragal's unique slide bolt design allows for smooth and secure engagement, while the adjustable strike and deadbolt plates ensure a precise fit. The included corner pads help to establish proper jamb side margins, ensuring accurate placement of the bolt receivers.

The Endura Ultimate Slide Bolt Astragal is also compatible with Z-series adjustable inswing cap sills and Z-articulating cap sills, making it a great choice for a variety of door configurations.

Endura Ultimate Slide Bolt Astragal

The Endura Ultimate Slide Bolt Astragal is a versatile and easy-to-install security device that can be used on inswing doors. It features a high-quality construction and a user-friendly design, making it a great choice for both residential and commercial applications.

The astragal's unique slide bolt design allows for smooth and secure engagement, while the adjustable strike and deadbolt plates ensure a precise fit. The included corner pads help to establish proper jamb side margins, ensuring accurate placement of the bolt receivers.

The Endura Ultimate Slide Bolt Astragal is also compatible with Z-series adjustable inswing cap sills and Z-articulating cap sills, making it a great choice for a variety of door configurations.

1
Ultimate Slide Bolt Astragal
Inswing Field Installation Instructions
• Lower Bolt Receiver
• Header Strike Plate
• (2) #6 x 1-1/2" Screws
Kit Includes:
• Pencil/Marker
• Utility Knife
• Flathead
Screwdriver
• Drill (3/8" and
5/8" Bits)
• Rubber Mallet
Tools Required: Before you begin: Install corner pads
on door hinge jambs to establish
proper jamb side margins. This ensures
accurate locations on header and sill
for the bolt receivers.
STEP 1: INSTALL HEADER AND SILL BOLT RECEIVERS
b. Press and engage the upper and lower bolts so the bolt
pins come in contact with the header and the sill. Mark these
points of contact.
d. At the marked location on the sill, drill a hole 5/8" in diameter and at
least 1-3/8" deep. Install the lower bolt receiver by tapping into the sill
with a rubber mallet.
NOTE: If using a Z-AC sill, no drilling is
necessary as the bolt receiver is pre-
installed.
a. Close the inactive door panel until
the weatherstrip on the header is
compressed.
Rev. Date: 06.20.2023
©Endura Products, Inc.
Innovation protected under patents and patents pending
in U.S. and Canada. See www.EnduraPatents.com
#211159-LTPLUS-I-FP
Z- ARTICULATING CAP SILL∏
Z-SERIES ADJUSTABLE INSWING CAP SILL
HEADER
SILL
c. At the marked location on the header, drill a hole 3/8" in diameter
and at least 1-3/8" deep. Install the header strike plate into the header,
using two #6 x 1-1/2" screws.
HEADER
8817 West Market Street
Colfax, NC 27235 | 800.334.2006
www.enduraproducts.com
2
STEP 2: INSTALL STRIKE AND DEADBOLT PLATES
a. When you are ready to install the hardware
on the door, pry off the dummy strike plates
using a athead screwdriver.
b. Install the strike and deadbolt plates
by screwing into the retainers.
a. Remove the retainers from the astragal body by pushing the tabs in
and rotating the retainer out.
c. Break retainer in half using the bend lines. Return the two
pieces of the retainer to the astragal and adjust to t the larger
hardware.
If the hardware has mounting holes greater than 1-5/8" center to center:
>1-5/8"
b. Remove the trim strip from the
astragal and set aside.
e. Resize the trim strip to t ush against the
deadbolt and strike plates and install into the
astragal.
d. Adjust the location of the two pieces of the
retainer and install the new hardware.
Ultimate Slide Bolt Astragal Inswing Field Installation Instructions
3
Ultimate Slide Bolt Astragal Inswing Field Installation Instructions
STEP 4: CONFIRM PROPER INSTALLATION
a. With the inactive door closed, engage both the upper and
lower bolts to ensure they t into the bolt receivers smoothly.
b. Close the active door panel and ensure the deadbolt and strike
plates are aligned with the crossbore holes in the active door panel.
View from behind
door unit
c. If the plates are not aligned correctly,
loosen screws and slightly adjust the
locations of the plates.
STEP 3: CUT WEATHERSTRIP AT HEADER
a. Close the inactive door. Make a mark at the location
where the trim cap contacts the weatherstrip.
b. Open the inactive door. Using a utility knife, make a slit in
the weatherstrip along the mark made.
c. Close the active door panel and ensure the weatherstrip
forms a secure seal around the trim cap.
View from behind
door unit
Cut
Here
View from behind
door unit
  • Page 1 1
  • Page 2 2
  • Page 3 3

Endura Ultimate Slide Bolt Astragal Operating instructions

Endura
Brand
Endura
Model
Ultimate Slide Bolt Astragal
Type
Operating instructions
This manual is also suitable for

Endura Ultimate Slide Bolt Astragal

The Endura Ultimate Slide Bolt Astragal is a versatile and easy-to-install security device that can be used on inswing doors. It features a high-quality construction and a user-friendly design, making it a great choice for both residential and commercial applications.

The astragal's unique slide bolt design allows for smooth and secure engagement, while the adjustable strike and deadbolt plates ensure a precise fit. The included corner pads help to establish proper jamb side margins, ensuring accurate placement of the bolt receivers.

The Endura Ultimate Slide Bolt Astragal is also compatible with Z-series adjustable inswing cap sills and Z-articulating cap sills, making it a great choice for a variety of door configurations.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI