2. Vada
  3. 9510082

Vada 9510082, 9510454, 9510456 Quick start guide

  • Hello! I've analyzed the provided Quick Start Guide for the Vada Flow Boss Automatic Pressure Control (VFB-APC) and related Vada pumps. This guide includes setup instructions for various models, information about the LED indicators, pressure adjustment and also options with Mechanical Water Switching Unit. I’m ready to assist with any questions you have about these products or the installation process.
  • What is the purpose of the LED light panel?
    How do I adjust the cut-in pressure?
    What does a flashing red light indicate?
    What does a solid red light indicate?
Quick Start Guide
Vada Flow Boss
Automatic Pressure Control
VFB-APC
Scan for
set up
support
32 VADA FLOW BOSS AUTOMATIC PRESSURE CONTROL VFB-APC QUICK START GUIDE
THANK YOU
• Use a pump cover to protect your setup from the elements and increase its lifespan.
• If installing with a Vada Flow Boss Mechanical Water Switching Unit, you will require a flathead
screwdriver to adjust the cut-in pressure. Please use thread tape.
• Ensure your pump setup is equipped with two isolation valves. This allows for fuss free
troubleshooting should you need it.
• If you are switching from tank to mains water, you will also need to install a Vada Flow Boss
Mechanical Water Switching Unit (VFB-MSU).
COMPATIBLE VADA PRODUCTS:
• Inlet: 25mm MI
• Outlet: 25mm MI
• Max operating pressure: 1000kPa / 10 bar
• Minimum pump pressure: 250kPa / 2.5 bar
• Min – max water temperature: 1°C – 65°C
• Min – max ambient temperature: 1°C – 40°C
• Supply voltage: 1~240V 50Hz
• Cut-in pressure: 150 – 300kPA / 1.5 – 3bar
• Max power: 1.5kW
• Max current: 10A
• IP rating: IP65
ADDITIONAL PRODUCTS REQUIRED FOR INSTALLATION:
SPECIFICATIONS
HELPFUL HINTS
Swing check valve Y-Strainer
(AKA Inline Strainer)
Thank you for purchasing a Vada Flow Boss Auto Pressure Control.
Designed with an LED light panel to signal the state of operation, a built
in pressure gauge to allow for adjustable cut-in pressure and a 24 hour
reset function for hassle free operation.
Thread tape Pump cover
Vada Flow
Boss Horizontal
Multistage Pump
VFB-HM80
VFB-HM110
Vada Flow Boss
Jet Pump
VFB-J40
VFB-J60
VFB-J90
Vada Flow Boss
Submersible Pump
VFB-S35
Vada Flow Boss
Submersible Pump
VFB-S75
Power On indicator
Pump On indicator
Error indicator
Restart button
Three-wire cable
25mm MI Inlet
Cut-in pressure
adjustment point
25mm MI Outlet
54 VADA FLOW BOSS AUTOMATIC PRESSURE CONTROL VFB-APC QUICK START GUIDE
5. Connect the IEC plug cord on the VFB-
APC to the IEC socket on the pump by
pushing them firmly into each other.
Ensure there are no water traces on the
connectors.
If you are installing a Vada Flow Boss
Mechanical Water Switching Unit skip
to step 8.
6. Plug the power lead in to the power point
and turn the switch on.
7. The green ‘Power On’ LED will illuminate.
If you are using a Tank Only system, then
you are ready to operate the pump.
If you are using a MSU continue to step
8. Ensure you have selected the correctly
sized MSU for your pump application.
8. Grab the rubber washer supplied with the
VFB-MSU and place it on top of the Auto
Pressure Control (VFB-APC) outlet.
9. Hold the Mechanical Switching Unit
(VFB-MSU) over the outlet and connect the
loose nut. Do not overtighten. The rubber
washer will lock this in place.
10. Connect the mains water pipe to the
VFB-MSU inlet labelled “mains in”.
Connect the house water pipe to the
VFB-MSU outlet labelled “to house”.
Note: For easy maintenance, add an isolation
valve into both lines.
Error
Pump on
Power on
Restart
1~240V 50 Hz
Max 1.5kW 8A
Max 65°C
IP65
Max 1MPa (10 bar)
AUTO PRESSURE CONTROL
VFB-APC
Power on
Pump on
Error
Restart
AUTO PRESSURE CONTROL
FLOW BOSS
240-50Hz
Max 1.5kW
Max 1MPa
8A
IP65
ON
If you are installing a Vada Flow Boss
Pump with a Vada Flow Boss Auto
Pressure Control (VFB-APC), follow
steps 1–7.
If you are installing a Vada Flow Boss
Pump with a Vada Flow Boss Auto
Pressure Control and Vada Flow Boss
Mechanical Water Switching Unit, follow
steps 1–14.
1. Set up the suction line installing an isolation
valve, swing check valve, y-strainer and
barrel union for optimal performance and
easy maintenance.
2. Ensure your pump is primed.
Note: Refer to your pump manual for
instructions on how to prime a pump.
3. Connect the VFB-APC to the pump either
directly with a 25mm barrel union or
between the pump and the first outlet. Use
thread tape to ensure a watertight seal.
Note: The pipe/hose must have an internal
diameter equal or larger than the outlet port
of the pump.
4. Check your set up, ensuring the VFB-APC
is installed with the arrows in the up position.
Solid level
base
INSTALLATION
Power on
Pump on
Error
Restart
AUTO PRESSURE CONTROL
FLOW BOSS
240-50Hz
Max 1.5kW
Max 1MPa
8A
IP65
100mm
Solid level base
Power on
Pump on
Error
Restart
AUTO PRESSURE CONTROL
FLOW BOSS
240-50Hz
Max 1.5kW
Max 1MPa
8A
IP65
To house Mains water in
76 VADA FLOW BOSS AUTOMATIC PRESSURE CONTROL VFB-APC QUICK START GUIDE
Green light
The pump is connected to the power supply
successfully.
Yellow light
The connected pump is operating.
Note: On initial start up the pump will run until
the discharge line is primed to remove all air.
Red light
Flashing red: Loss of flow detected. While the
red light is flashing, the pump will remain on for
20 seconds, then turn off as it tries to re-prime
itself. It will attempt this several times.
Solid red: The pump has not been able to
detect water and cannot re-prime itself. The
pump will turn off for 24 hours, or until reset.
To reset, turn the power off, then on or
press the restart button.
INTERPRETING THE APC
Error
Pump on
Power on
Restart
1~240V 50 Hz
Max 1.5kW 10A
Max 65°C
IP65
Max 1MPa (10 bar)
AUTO PRESSURE CONTROL
VFB-APC
Error
Pump on
Power on
Restart
1~240V 50 Hz
Max 1.5kW 10A
Max 65°C
IP65
Max 1MPa (10 bar)
AUTO PRESSURE CONTROL
VFB-APC
Error
Pump on
Power on
Restart
1~240V 50 Hz
Max 1.5kW 10A
Max 65°C
IP65
Max 1MPa (10 bar)
AUTO PRESSURE CONTROL
VFB-APC
11. Prepare to adjust the cut-in pressure by
locating the adjustment screw at the back
of the VFB-APC.
Note: Adjusting the cut-in pressure from the
default of 150kPa (1.5bar) to 220kPa (2.2Bar)
allows for a smooth, more reliable changeover
between tank and mains water.
12. Using a flat head screwdriver, turn the
adjustment screw clockwise until you reach
the correct pressure (approx 3.5 full
360° turns).
Note: If you are having trouble turning the
adjustment screw, turn the power off. Isolate
the Mains water supply line. Open the tap to
discharge some water to release the pressure
from within the system. You should now be
able to turn the adjustment screw.
13. Confirm the pressure has been correctly
adjusted by slowly opening a tap outlet
and checking the gauge on the side of the
VFB-APC. If the pump turns on when
gauge drops to 2.2 bar, the cut-in pressure
has been successfully adjusted.
14. Fit a pump cover to protect your setup
from the elements and increase product
lifespan.
Solid level base
To house Mains water in
INSTALLATION
98 VADA FLOW BOSS AUTOMATIC PRESSURE CONTROL VFB-APC QUICK START GUIDE
OPTION 2: ABOVE GROUND FLOW BOSS SET UP
• Vada Flow Boss Jet Pump VFB-J40, VFB-J60, VFB-J90 or
Horizontal Multistage Pump VFB-HM80, VFB-HM110
• Vada Flow Boss Auto Pressure Control VFB-APC
• Vada Flow Boss Mechanical Switching Unit VFB-MSU (20 or 25mm)
OPTION 1: ABOVE GROUND FLOW BOSS SET UP
• Vada Flow Boss Jet Pump VFB-J40, VFB-J60, VFB-J90 or
Horizontal Multistage Pump VFB-HM80, VFB-HM110
• Vada Flow Boss Auto Pressure Control VFB-APC
FLOW BOSS SET UP OPTIONS
Barrel unionY Strainer
Solid level base
Recommended
150mm
To house
Isolation
valve
Isolation
valve VFB-MSU
VFB-APC
Barrel union
Discharge pipe Mains pipe
To mains
House wall
25mm
isolation
valve
Swing
check
valve
100mm
Min 100mm
25mm
isolation
valve
25mm
isolation
valve
VFB-APC
25mm barrel union
25mm
barrel union
25mm Y Strainer
Solid level base
To house
100mm
Recommended
150mm
House wall
Min 100mm
1110 VADA FLOW BOSS AUTOMATIC PRESSURE CONTROL VFB-APC QUICK START GUIDE
25mm Check Valve
VFB-APC
VFB-S35
25mm Barrel Union
Discharge Pipe Min 25mm
Flow
25mm Y Strainer
Ground Level
25mm
isolation
valve
To house
House wall
OPTION 3: BELOW GROUND FLOW BOSS SET UP
• Vada Flow Boss Jet Pump VFB-J40, VFB-J60, VFB-J90 or
Horizontal Multistage Pump VFB-HM80, VFB-HM110
• Vada Flow Boss Auto Pressure Control VFB-APC
• Vada Flow Boss Mechanical Switching Unit VFB-MSU (20 or 25mm)
OPTION 4: BELOW GROUND FLOW BOSS SET UP
• Vada Flow Boss Submersible Pump VFB-S35
• Vada Flow Boss Auto Pressure Control VFB-APC
FLOW BOSS SET UP OPTIONS
Recommended
150mm
Flow
VFB-APC
25mm barrel union
25mm
barrel union Ground level
Solid level base
House wall
100mm
Suction pipe
min 25mm
Foot valve
25mm
isolation
valve
To house
Min 100mm
OPTION 5: BELOW GROUND FLOW BOSS SET UP
• Vada Flow Boss Submersible Pump VFB-S75
• Vada Flow Boss Auto Pressure Control VFB-APC
• Vada Flow Boss Mechanical Switching Unit VFB-MSU25
To house
25mm
isolation
valve
25mm
isolation
valve VFB-MSU25
VFB-APC
VFB-S75
32mm barrel union
Discharge pipe
min 20mm
Discharge pipe min 32mm
Mains pipe
min 20mm
To mains
Flow
32mm Y strainer
Ground level
100mm
FLOW BOSS SET UP OPTIONS
/