Ventomist VTHPMF-2405 User guide

VTHPMF-2405

High Pressure Misting Fan 24”

by

www.ventomist.com +1 (281) 724-8222 [email protected]

Customer:

Customer PO#:

VENTO SO#:

Tested By:

Serial #:

Ship Date / Install Date:

VTHPMF-2405

High Pressure Misting Fan 24”

by

www.ventomist.com +1 (281) 724-8222 [email protected]

General Safety Information

MACHINE WARNING SIGNS

Indicates an imminently

hazardous situation which,

if not avoided, will result in

death or serious injury.

Indicates a potentially

hazardous situation which,

if not avoided, could result

in death or serious injury.

Indicates a potentially

hazardous situation which,

if not avoided, may result

in minor or moderate

injury.

Used without the safety

alert symbol ( ) indicates

potentially hazardous

situation which, if not

avoided, may result in

property damage.

Warning of electric shock

Do not expose the

equipment to rain or use in

damp locations.

Do not use the equipment

around flammable products,

if not avoided, sparks can

ignite vapors from

flammable products.

Read and understand all

warnings and operating

instructions before using this

equipment. Failure to follow

all instructions may result in

electric shock, fire, and/or

serious personal injury or

property damage.

Figure 1

VTHPMF-2405 
 
High Pressure Misting Fan 24” 
 
 by   
www.ventomist.com +1 (281) 724-8222            [email protected] 
 
TABLE OF CONTENTS 
MACHINE WARNING SIGNS .................................................................................. 2 
General Safety Information ................................................................................... 4 
Installation .......................................................................................................... 6 
Performance Record ……………………………………………………………………………………… 10 
Front view………………………………………………………………………………………………………12 
Back view………………………………………………………………………………………………………14 
INSTRUCTIONS………………………………………………………………………………………………16 
Repair Parts Illustration(Figure3) ........................................................................ 17 
Repair Parts List(Figure3) ................................................................................... 18 
Repair Parts Illustration(Figure4) ........................................................................ 19 
Repair Parts List(Figure4) ................................................................................... 20 
Repair Parts Illustration(Figure5) ........................................................................ 22 
Repair Parts List(Figure5) ................................................................................... 26 
How to clean the filter ........................................................................................ 32

VTHPMF-2405

High Pressure Misting Fan 24”

4

by

www.ventomist.com +1 (281) 724-8222 [email protected]

General Safety Information

To reduce the risk of short circuit, please place the unit in a dry area.

To reduce the risk of burns, do not touch the surface of the pump while

operating.

Do not handle the pump or motor with wet hands.

Check the hose for weak or worn areas and the pump’s oil level before each

use.

To reduce the risk of electric shock, turn off motor before any maintenance

and trouble shooting.

Please ensure the water source is turned on before operation, or the pump

will be damaged. Never run the pump without water.

While operating the pump, please supervise the safety of children.

VTHPMF-2405

High Pressure Misting Fan 24”

5

by

www.ventomist.com +1 (281) 724-8222 [email protected]

General Safety Information

△

!ATTENTION

 Read the manual and safety precautions before using this misting fan.

 Please make sure the misting fan is properly grounded.

 While operating the misting fan, please supervise the safety of children.

 To reduce the risk of short circuit, please place the misting fan in a dry place.

 Please empty the water from the tank when not in use.

△

!WARNINGS

 The electrical power supply voltage and frequency must match that specified on the

misting fan.

 To reduce the risk of electric shock, turn off the motor before any maintenance and

troubleshooting.

 The unit must not be run without water. Lack of water will cause serious damage to

the pump.

△

!DANGEROUS

 To reduce the risk of burns, do not touch the surface of the pump while operating.

 It is highly risky to use the misting fan without the ground-fault circuit-interrupter

(GFCI); this device is provided to avoid the risk of electric shock.

 For safety concerns, please disconnect the plug of the misting fan from the power

supply when not in use.

 Do not handle the pump or motor with wet hands.

 Do not operate the misting fan in the rain or during thunderstorms.

VTHPMF-2405

High Pressure Misting Fan 24”

6

by

www.ventomist.com +1 (281) 724-8222 [email protected]

Instructions

A. Before Operation

1. Make sure to fill the pump with the oil that has been provided to you before

turning on the unit. Failure to add oil to the pump will result in damage to the

pump and void the warranty of this unit.

VTHPMF-2405

High Pressure Misting Fan 24”

7

by

www.ventomist.com +1 (281) 724-8222 [email protected]

2. Make sure that the pump is firmly installed and the connectors are tightened

properly.

3. Before operating the motor, turn on the water source and check whether the

suction hose is connected to the pump properly. Discharge redundant air inside

the pump.

4. The water’s pressure should be at least 50 PSI.

5. Make sure the diameter of the suction hose is 3/4 inch.

6. Make sure the diameter of any extension cords used is larger than 18AWG.

B. Maintenance

1. Change the oil when the pump has been used for the first 30~50 hours.

2. After the initial oil change, replace the oil after every 100~200 hours of

operation.

3. Use #30~40 oil, add 70 cc each time.

C. Troubleshooting

1. UNSTABLE WORKING PRESSURE

(a) Check whether the suction hose is leaking, clogged or afloat.

(b) Drain out the redundant air by disconnecting the outlet hose.

(c) Check the valve assembly to see if it is clogged or damaged.(1)

2. INSUFFICIENT PRESSURE

(a) Check to see if the packing, waterproof seal(3) and valve assembly(1) are

damaged.

(b) Check to see if the pressure valve and regulating spring are worn out.(2)

3. LEAKAGE

(a) Check the U-Packing, waterproof seal and piston. Replace them if

necessary.(3)

VTHPMF-2405

High Pressure Misting Fan 24”

8

by

www.ventomist.com +1 (281) 724-8222 [email protected]

4. UNUSUAL NOISE

(a) Check the piston and oil. Replace them if necessary.

(b) Check the water’s pressure.

(c) Check whether the nozzles are clogged.

VTHPMF-2405

High Pressure Misting Fan 24”

9

by

www.ventomist.com +1 (281) 724-8222 [email protected]

Machine Oil

Type

SAE-30-40

Oil Volume

70CC

Oil Change

Frequency

1. Initial change, after 30-50

hours of use.

2. After initial oil change,

every 100-200 hours of

use.

70 CC

VTHPMF-2405

High Pressure Misting Fan 24”

10

by

www.ventomist.com +1 (281) 724-8222 [email protected]

△

!ATTENTION

Please do not change the oil immediately after using the misting fan. The oil will be hot

and might cause personal injury. Wait at least 30 minutes before changing the oil.

TURNING OFF THE MISTING FAN & STORAGE

If the misting fan will not be used for a long period of time, please follow these

instructions.

1. Turn off the water supply and take off the suction hose.

2. Open the drain plug at the bottom of the water tank to release the water out. Clean

the filters (1) (2).

3. Press the air release valve to exhaust the air from the pump. Press to eliminate

the water frm the pump and hose. Pump will stop due to the duration of alarm

without water is 15 seconds. If water still remains, please unplug the power and plug

again to repeat this step.

4. Turn off the timer to stop spraying. Switch the fan speed knob to “0” to stop the fan.

5. Unplug the power cable from the socket.

6. Store the unit in a cool dry place away from hazardous conditions.

VTHPMF-2405

High Pressure Misting Fan 24”

11

by

www.ventomist.com +1 (281) 724-8222 [email protected]

Performance Record

VTHPMF-2405

High Pressure Misting Fan 24”

12

by

www.ventomist.com +1 (281) 724-8222 [email protected]

[Front view]

[Side view]

VTHPMF-2405

High Pressure Misting Fan 24”

13

by

www.ventomist.com +1 (281) 724-8222 [email protected]

[Side view]

[Back view]

VTHPMF-2405

High Pressure Misting Fan 24”

14

by

www.ventomist.com +1 (281) 724-8222 [email protected]

Water Inlet

Control Panel

Float sensor

and water

level indicator

VTHPMF-2405

High Pressure Misting Fan 24”

15

by

www.ventomist.com +1 (281) 724-8222 [email protected]

[Front view]

VTHPMF-2405

High Pressure Misting Fan 24”

16

by

www.ventomist.com +1 (281) 724-8222 [email protected]

Water

Tank

Oil inlet cover

Pressure regulator

Outlet

Inlet

Oil window

Drainage screw

Circuit breaker

VTHPMF-2405

High Pressure Misting Fan 24”

17

by

www.ventomist.com +1 (281) 724-8222 [email protected]

A. Before Operation

1. Lock the casters to prevent the misting fan from accidentally moving.

2. Make sure the fan brake is released before moving.

3. Make sure the fan is connected secured securely to hhe unit and adjust the fan height.

4. Fasten the water hose to the inlet socket on the water tank.

5. Connect the nozzles to the misting ring tigjtly to prevent leaking.

6. Use only clean water and check that there is sufficient water in the tank.

7. Check that the power cable is connected to a power supply of the correct voltage and

frequency.

8. Set the running and stop times on the timer and adjust the fan angle and speed.

(For more information on setting the timer, please see Digital Timer Instructions,

Page 36.)

9. Constantly push the air release valve for 15 seconds when running the pump for the

fist time, when restarting the pump after it has run out of water, or after a long period

without use.

△

!ATTENTION:

Make sure the length of the cable is longer than 10 meters and the diameter of extension

cords used is larger than 18AWG.

B. Filling the water tank

1. Donot fill water over the water float or the water might splash out and cause

malfunction.

2. Do not take the water filter away while filling the water to the tank.

3. Keep motor and electrical devices in dry conditions while adding the water to the

tank.

C. After Operation

1. Press OFF for 5 seconds to stop the misting pump.

2. Stop the fan and turn off the water supply.

3. Open the drain cap on the bottom to empty the tank.

GENERAL INSTRUCTIONS

VTHPMF-2405

High Pressure Misting Fan 24”

18

by

www.ventomist.com +1 (281) 724-8222 [email protected]

Repair Parts Illustration (Figure 2)

Figure 2

VTHPMF-2405

High Pressure Misting Fan 24”

19

by

www.ventomist.com +1 (281) 724-8222 [email protected]

Repair Parts List (Figure 2)

Repair Parts List for Misting Fan

Reference

Number

Description

Part Number

Quantity

1

Stainless Steel Ring

VTHPMF-2405-01

1

2

Clamp

VTHPMF-2405-02

3

Misting Nozzles

VTHPMF-2405-03

6

4

Nipple

VTHPMF-2405-04

1

5

Nipple

VTHPMF-2405-05

1

6

Fitting

VTHPMF-2405-06

1

7

Front Guard

VTHPMF-2405-07

1

8

Phillips Head Screw

VTHPMF-2405-08

12

9

Propeller Fan

VTHPMF-2405-09

1

10

Hex Screw

VTHPMF-2405-10

1

11

Back Guard

VTHPMF-2405-11

1

12

Hex Motor Frame Screws

VTHPMF-2405-12

4

13

Motor

VTHPMF-2405-13

1

14

Hex Screw

VTHPMF-2405-14

2

15

Sleeve

VTHPMF-2405-15

1

16

Power Cord

VTHPMF-2405-16

1

17

Filter

VTHPMF-2405-17

1

VTHPMF-2405

High Pressure Misting Fan 24”

20

by

www.ventomist.com +1 (281) 724-8222 [email protected]

Repair Parts Illustration (Figure 3)

Figure 3

Page is loading ...