Figure 1 - Installing the WRC Remote Receiver
1. Depending on the model, you must access the ignition control module
by removing either the lower louver access panel or the lower control
cover. Refer to the installation manual included with your appliance when
shipped.
2. If a wall switch was installed to the ignition module, it must be removed
from the ignition control circuit for the remote to work properly. Remove
the wire nuts from the switch connection at the ignition control module.
Using one of the wire nuts, connect the transformer (blue) wire to the
remaining wire connected to the control terminal marked (PSW) see
Figure 3.
3. The WRC model receiver does not require a battery and can be installed
by plugging the extension cord into one of the outlet receptacles on the
outlet box, then plug the receiver unit into the extension cord and fi nally
plug the ignition module into the receiver unit, see Figure 1, Page 2.
4. Replace the louver or the control access panel.
5. Activate the handset battery by removing the insulating tab on the back
of the handset. See Figure 2.
6. Once the battery is activated the unit is ready to use.
INSIDE APPLIANCE TOWARDS FRONT
Extension Cord
Optional Fan Kit
Plug
Ignition Module
Plug
Junction Box
Remote
Receiver
OPTIONAL REMOTE CONTROL KIT
[FOR USE WITH MODELS MISSION36/42, ODYSSEY36/42, VRE3036/42]
OPTIONAL REMOTE CONTROL KIT
36/42 FIREPLACES
P/N 127161-01
Rev. B, 03/2017
HEARTH PRODUCTS
KITS AND ACCESSORIES
ON
OFF
KIT CONTENTS
1 ea. Remote Control System
1 ea. Extension Cord
1 ea. Instruction Sheet
Cat. No. Model Description
F1080 WRC Standard Electronic On/Off Remote Control Kit
REQUIRED TOOLS AND SUPPLIES
None
GENERAL INFORMATION
The hand-held ON/OFF remote control may be used to control the
operation of the fi replace burner.
READ ALL THE STEPS BEFORE STARTING THE INSTALLATION
THE FIREPLACE MUST BE OFF AND COLD BEFORE BEGINNING.
ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS IN THE
INSTALLATION AND OPERATION MANUAL PROVIDED WITH THE
APPLIANCE APPLY TO THESE INSTRUCTIONS.
If you encounter any problems, need clarifi cation of these instructions
or are not qualifi ed to properly install this kit, contact you local
distributor or dealer.
If any of these parts are missing or damaged, contact your dealer or
IHP.us.com for referral information.
INSTALLATION INSTRUCTIONS
(Electronic Models Only)
This option is for an Electronic Ignition Unit with 110 Volt AC electricity
wired to the unit. The Receiver is plugged into the Extension Cord, which
is plugged into the junction box. The plug from the Gas Appliance control
assembly is plugged into the Receiver (see Figure 1).
127161-01B 1
IHP.us.com
2
Figure 2 - Installing Battery in Hand Held Remote
Figure 3 - Installing Wall Switch
Plug 120V AC to
Receptacle
Ignition
Control
Module
Make Connections
with Wire nuts
Route Millivolt Wires
Through Gas Line Conduit
Sleeve.
18 AGW Red Wire
Wall Switch
Back View
Transformer
Electrode
TO GAS VALVE
Battery Cover
12 Volt Battery
Pull to Remove
Insulation Tab
Back of
Handset
INSTALLING A ALKALINE BATTERY IN HAND HELD REMOTE
CONTROL UNIT
1. Remove battery cover on back of remote control unit.
2. Attach terminal wires to the battery (not included).Place battery into
the battery housing.
3. Replace battery cover onto remote control unit.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Printed in U.S.A. © 2014 Innovative Hearth Products
P/N 127161-01 Rev. B 03/2017
IHP reserves the right to make changes at any time, without notice, in design, materials, specifi ca-
tions, prices and also to discontinue colors, styles and products. Consult your local distributor
for fi replace code information.
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
-
1
-
2
Astria Fireplaces Double Flame Century Oak LVD 18/24 CO Instruction Sheet
- Type
- Instruction Sheet
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
FMI WRC Operating instructions
-
Desa (V) CB36(N User manual
-
-
-
-
-
-
-
-