Page is loading ...
1
LL-2WLD RGB
Professional Stage Lighting Laser show
Professional stage animation laser light
2
Thank you for purchasing this product. To optimize the performance of this
product, prior to use, please read these operating instructions carefully to
familiarise yourself with the basic operation of this unit. Please keep the
manual in safe price for future reference.
This unit has been tested at our factory before being shipped to you, there is
no assembly required.
Once after received this product , please take and put carefully. And check
cautiously that whether the product was damaged or not during the
transportation.
Checking Parts
Please check if the following parts are included:
1 x Laser
1 x Power cable
1 x User manual
Danger Laser Radiation!
Avoid direct eye exposure!
Laser radiation can cause eye damage or skin damage
All protective measures for a safe operation of this laser must be applied.
Installation
1. Please check the voltage whether is the same with the one showed on the
equipment or not.
2. It must ask for the technical person and set the light safety when installation.
And let the light beam at the suitable angle.
3. When install this equipment please make sure there's no flammable
surfaces (decorated things, etc) within at least 2.5M and maintain minimum
distance of 0.5M from the equipment to the walls.
4. Please make sure that there's no other equipment or decorating materials
obstructed the exhaust fan and the vent-pipe.
5. Products should be install immobility.
6. In case of safety, it's very important that to connect the earth with line.
Attention
1.Please do not open the bottom cover yourself without permission.Operate it
accord the user manual. Call the technician when the machine breaks down.
2.Please do not see the laser beam directly to avoid any damage.
3.Before connect or disconnect the power, please adjust the luminance of the
laser diode to the least to avoid any damage to the laser diode.
3
4.This unit should be keep dry, do not use in the rain and dusty environment. It
can be use in the outdoor with the water-proof cover protector.
5. Set the light immobility and try to avoid strong shake or hit.
6.Prevent dust into the equipment to avoid problems.
7.Please keep that there's no other equipment or decorating materials
obstructed the exhaust fan and the vent-pipe when the equipment was
working.
8.Before connect power, check the plug is immobility or not, power line should
be connect well.
9.Please do not open or close the equipment frequently that's to avoid any
affect to the life span of the laser diode, and try the best to avoid the long time
working.
10.Due to the characteristic of the laser diode, after four hours working, it
should be close at least 25 minutes until the laser diode cooling then work
again.
11.Don't touch the light or draw the power line when your hand was wet. And
do not pull the electronic power line.
12.Maintain the distance at least 3M above from the equipment to the object.
13.This equipment does not have any parts can repair for the users, please do
not open the equipment.
14.When the laser diode became dim or damaged please contact the dealer
timely.
15.When you want to retransfer the products, you'd better use the original
package to shockproof.
LCD setting: (when the ILDA interface connected to the
exterior console, LCD setting invalid)
Mode
LCD DISPLAY
1
DMX512 Control
2
Auto
3
Music
DMX-512
Auto
Address
001
Address
001
DMX-512
Auto
Show
001
Music
Testing
Show
001
4
DMX setting:
Input dmx singal, and the link the dmx controller and the lights by the
control line as the following picture, you can control the lights by the
controller.
1. Master-slave setting:
Link the lights as the following picture (the light which does not receive
signal, only output signal, will be the master light)
LCD display panel, as following
ENTER UP
Exit DOWN
1. Touch keys and LCD menu display, menu operation is simple and easy to use.
2. After loading the software to display the software version（Sof-v2.8）。
3. Through the UP and DOWN buttons to select the need of function。
4. Determined by the selected function ENTER and Exit button, return to the higher level
menu。
DMX-512
Auto
5
Using before pls must be check power supply link with
earth wire correctly or not.
The specification of the front and rear panel:
1. Power input to the socket
2. Power ON/OFF
3. Laser safety key
4. LCD display
5. DMX IN/OUT:DMX signal output and input
6. When the ILDA interface is connected to the exterior console, light will automatically change
to exterior control mode, and needn`t convert switch
7. Min-Max: Volume and sensitivity adjustment
8. MIC: microphone
Laser Graphic - Animated - PC Control ILDA
Professional 25Kbps High Speed Optical Scanner
Diodes:
- New Construction Technology, Diodes mounted in a single enclosure,
more vivid colors, better alignment and better performance.
- Red 500mW / 635nm - Green 500mW / 520nm - 1W / 445nm Blue
Color Mix: White Laser 2W
Working Modes: Sound, Auto Animation, Auto, ILDA PC Control, Dmx 512,
Master / Slave.
DMX: DMX 12/23 Channels
Product Size: 47x39x21cm
Product weight: 4KG
Packing size: 40x33x27
Gross weight: 6kg
6
LCD function menu Settings, as following：
7
DMX-512 channel Description ：
1、12channel-mode, as following:
channel
channel
value
control content
CH1
close light
0～41
Laser OFF
Automatic
42～83
Manual control CH2-CH12 valid
84～125
Run beam effects build-in, CH2-CH12 invalid
126～167
Run animation effects build-in, CH2-CH12
invalid
Music
168~209
Run beam effects build-in, CH2-CH12 invalid
210～251
Run animation effects build-in, CH2-CH12
invalid
252~255
Manual control CH2-CH12 valid
CH2
Patterns
choose
0~255
Each of the 2 value of a patterns, when
CH1=42~83
Animation
patterns
choose
0~255
9 animation effects choose,when CH1=126~167
or 210~251
CH3
pattern
rotating
1～127
rotating angle choose
128～159
30°rotating speed choose
160～191
180°rotating speed choose
192～223
left rotating speed choose
224～255
right rotating speed choose
CH4
pattern level
rotating
1～127
level rotating angle choose
128～159
level rotating speed choose
160～191
192～223
224～255
CH5
pattern
vertical
rotating
1～127
vertical rotating angle choose
128～159
vertical rotating speed choose
160～191
192～223
224～255
CH6
pattern level
moving
1～127
level moving site choose
128～159
level moving speed choose
160～191
192～223
224～255
1～127
vertical moving site choose
8
CH7
pattern
vertical
moving
128～159
vertical moving speed choose
160～191
192～223
224～255
CH8
pattern
zoom
1～127
pattern size choose
128～159
zoom out speed choose
160～191
enlarge speed choose
192～223
zoom speed choose
224～255
CH9
zoom resizing
1～255
pattern zoom resizing choose
CH10
pattern
drawing
1～127
drawing speed choose
128～255
CH11
pattern point
1～127
scanner speed choose
128～255
CH12
color mode
0～63
fixed color choose
64～95
change color effect speed choose
96～127
128～159
running effect speed choose
160～191
192～223
224～255
drawing effect speed choose
2、23channel-mode, as following:
channel
channel
value
control content
CH1
close light
0～41
Laser OFF
Automatic
42～83
Manual control CH2-CH23 valid
84～125
Run beam effects build-in, CH2-CH23 invalid
126～167
Run animation effects build-in, CH2-CH23
invalid
Music
168~209
Run beam effects build-in, CH2-CH23 invalid
210～251
Run animation effects build-in, CH2-CH23
invalid
252~255
Manual control CH2-CH23 valid
CH2
Patterns
choose
0~255
Each of the 2 value of a patterns, when
CH1=42~83
Animation
patterns
choose
0~255
9 animation effects choose,when CH1=126~167
or 210~251
CH3
pattern A
rotating
1～127
rotating angle choose
128～159
30°rotating speed choose
160～191
180°rotating speed choose
9
192～223
left rotating speed choose
224～255
right rotating speed choose
CH4
pattern A level
rotating
1～127
level rotating angle choose
128～159
level rotating speed choose
160～191
192～223
224～255
CH5
pattern A
vertical
rotating
1～127
vertical rotating angle choose
128～159
vertical rotating speed choose
160～191
192～223
224～255
CH6
pattern A level
moving
1～127
level moving site choose
128～159
level moving speed choose
160～191
192～223
224～255
CH7
pattern A
vertical
moving
1～127
vertical moving site choose
128～159
vertical moving speed choose
160～191
192～223
224～255
CH8
pattern A
zoom
1～127
pattern size choose
128～159
zoom out speed choose
160～191
enlarge speed choose
192～223
zoom speed choose
224～255
CH9
pattern A
zoom resizing
1～255
pattern zoom resizing choose
CH10
pattern A
drawing
1～127
drawing speed choose
128～255
CH11
pattern A
point
1～127
scanner speed choose
128～255
CH12
pattern A color
mode
0～63
fixed color choose
64～95
change color effect speed choose
96～127
128～159
running effect speed choose
160～191
192～223
224～255
drawing effect speed choose
CH13
pattern B
choosing
0～255
Every two values to choose a pattern
1～127
rotating angle choose
10
CH14
pattern B
rotating
128～159
30°rotating speed choose
160～191
180°rotating speed choose
192～223
left rotating speed choose
224～255
right rotating speed choose
CH15
pattern B level
rotating
1～127
level rotating angle choose
128～159
level rotating speed choose
160～191
192～223
224～255
CH16
pattern B
vertical
1～127
vertical rotating angle choose
128～159
vertical rotating speed choose
160～191
192～223
224～255
CH17
Pattern B level
moving
1～127
level moving site choose
128～159
level moving speed choose
160～191
192～223
224～255
CH18
patter B
vertical
moving
1～127
vertical moving site choose
128～159
vertical moving speed choose
160～191
192～223
224～255
CH19
pattern B
zoom
1～127
pattern size choose
128～159
zoom out speed choose
160～191
enlarge speed choose
192～223
zoom speed choose
224～255
CH20
pattern B
zoom resizing
1～255
pattern zoom resizing choose
CH21
pattern B
drawing
1～127
drawing speed choose
128～255
CH22
pattern B point
1～127
scanner speed choose
128～255
CH23
Pattern B
color mode
0～63
fixed color choose
64～95
change color effect speed choose
96～127
128～159
running effect speed choose
160～191
192～223
224～255
drawing effect speed choose
11
Maintenance
Maintenance should be performed every 15-day period, by using a sponge
which is dipped with alcohol, rather than wet cloth or other chemical liquid, to
clean the mirror.
Always disconnect from the mains when the device is not in use or before
cleaning it.
Warning
Power must be disconnected before maintenance or repair. Do not look at the
light source directly
Note
Don't separate laser machine from laser power and repair them by yourself ,
otherwise no good repair service will be supplied.
Declaration
This device has left our premises in absolutely perfect condition. In order to
maintain this condition and to ensure a safe operation, it is absolutely
necessary for the user to follow the safety instructions and warning notes
written in this user manual.
We cannot be made liable for damages caused by incorrect installations and
unskilled operation!
12
/
